Novel solvent effects in the photopolymerization of methyl methacrylate by use of quinoline–bromine charge-transfer complex as photoinitiator

Photopolymerization of MMA was carried out at 40°C in diluted systems by use of quinolinebromine (Q–Br₂) charge-transfer complex as the initiator and chloroform, carbon tetrachloride, chlorobenzene, dioxane, THF, acetone, benzene, toluene, quinoline, and pyridine as solvents. The results showed variable monomer exponents ranging from 1 to 3. For chloroform, carbon tetrachloride, and chlorobenzene, the monomer exponent observed was unity; for other solvents used, the value of the same exponent was much higher (between 2 and 3). Initiation of polymerization is considered to take place through radicals generated in the polymerization systems by the photodecomposition of (Q–Br₂)–monomer complex (C) formed instantaneously in situ on addition of the Q–Br₂ complex in monomer. The kinetic feature of high monomer exponent is considered to be due to higher order of stabilization of the initiating complex (C) in presence of the respective solvents. In the presence of the retarding solvents, very low or zero initiator exponents were also observed, depending on the nature and concentration of the solvents used. The deviation from the square-root dependence of rate on initiator concentration becomes higher at high solvent and initiator concentrations in general. This novel deviation is explained on the basis of initiator termination, probably via degradative chain transfer involving the solvent-modified initiating complexes and the propagating radicals.     

Photopolymerization of methyl methacrylate using triethylene tetramine-benzophenone combination as the photoinitiator

Photopolymerization of MMA at 40 was studied using triethylene tetramine (TETA)-benzophenone (BP) combination as the initiator. Initiator exponent is 0.5; monomer exponent is 1.0 in benzene, toluene, chlorobenzene, acetone and methyl ethyl ketone, < 1.0 in halomethanes (chloroform and carbon tetrachloride) and > 1 in methanol. Photoreduction of BP1(BP in the excited state) by ground state TETA via an exiplex formation is considered to produce chain-initiating radicals. Polymers obtained were found to bear amine end-groups. Termination takes place bimolecularly (initiator exponent being 0.5 in bulk as well as in diluted systems). The radical generation process is dependent on the nature of the solvent. The role of solvents in modifying the initiation or radical generation process has been examined and analysed.     

2‐[(Diphenylphosphino)methyl]pyridine as ligand for iron‐based atom transfer radical polymerization

2‐[(Diphenylphosphino)methyl]pyridine (DPPMP) was successfully used as a bidentate ligand in the iron‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) with various initiators and solvents. The effect of the catalytic system on ATRP was studied systematically. Most of the polymerizations with DPPMP ligand were well controlled with a linear increase in the number‐average molecular weights (M_n) versus conversion and relatively low molecular weight distributions (M_w/M_n = 1.10–1.3) being observed throughout the reactions, and the measured molecular weights matched the predicted values. Initially added iron(III) bromide improved the controllability of the polymerization reactions in terms of molecular weight control. The ratio of ligand to metal influenced the controllability of ATRP system, and the optimum ratio was found to be 2:1. It was shown that ATRP of MMA with FeX₂/DPPMP catalytic system (X = Cl, Br) initiated by 2‐bromopropionitrile (BPN) was controlled more effectively in toluene than in polar solvents. The rate of polymerization increased with increasing the polymerization temperature and the apparent activation energy was calculated to be 56.7 KJ mol^?1. In addition, reverse ATRP of MMA was able to be successfully carried out using AIBN in toluene at 80 °C. Polymerization of styrene (St) was found to be controlled well by using the PEBr/FeBr₂/DPPMP system in DMF at 110 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2922–2935, 2008     

Anionic polymerization of Lewis acid-activated methyl methacrylate by enamines

A novel ionic polymerization of methyl methacrylate (MMA) with a series of enamines (1) in the presence of methylaluminum bis(2,6-di-tert-butylphenoxide) (2) was examined. Both nucleophile (1) and electrophile (2) are indispensable for the present polymerization, in which (1) acts as initiator and (2) as activator. MMA polymerization proceeded smoothly in toluene at or below room temperature (r.t.) in the presence of 1 and 2 (1 ∼ 4 mol %, respectively), went to completion within 1 h, and afforded syndiotactic-rich PMMA with molecular weight distribution (M_w/M_n) in the 1.1 ∼ 1.4 range. The number-average molecular weight (M_n) of the polymer was significantly higher than that calculated from the feed ratio of 1 to the monomer, indicating low initiating efficiency. Kinetic studies coupled with isolation of an intermediate species proved that the real monomeric species involved in both initiation and propagation was a complex of MMA with 2. The effects of the concentrations of 1, 2, and MMA as well as the temperature of polymerization were also examined. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3671–3679, 1999     

Electroactive methacrylate‐based triblock copolymer elastomer for actuator application

A series of ABA triblock copolymers of methyl methacrylate (MMA) and dodecyl methacrylate (DMA) [poly(MMA‐b‐DMA‐b‐MMA)] (PMDM) were synthesized by Ru‐based sequential living radical polymerization. For this, DMA was first polymerized from a difunctional initiator, ethane‐1,2‐diyl bis(2‐chloro‐2‐phenylacetate) with combination of RuCl₂(PPh₃)₃ catalyst and nBu₃N additive in toluene at 80 °C. As the conversion of DMA reached over about 90%, MMA was directly added into the reaction solution to give PMDM with controlled molecular weight (M_w/M_n ≤ 1.2). These triblock copolymers showed well‐organized morphologies such as body centered cubic, hexagonal cylinder, and lamella structures both in bulk and in thin film by self‐assembly phenomenon with different poly(methyl methacrylate) (PMMA) weight fractions. Obtained PMDMs with 20–40 wt % of the PMMA segments showed excellent electroactive actuation behaviors at relatively low voltages, which was much superior compared to conventional styrene‐ethylene‐butylene‐styrene triblock copolymer systems due to its higher polarity derived from the methacrylate backbone and lower modulus. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

Photopolymerization of methyl methacrylate with the use of tetrahydrofuran–bromine charge-transfer complex as the photoinitiator

The polymerization of MMA was kinetically studied in the presence of visible light (using a 125-W high-pressure mercury vapor lamp with fluorescent coating, without a filter), a THF—bromine charge-transfer complex being used as the photoinitiator. The initiator exponent was 0.5 in bulk polymerization. The monomer exponent varied from about 1.2 to about 2.5, depending on the nature of the solvent used; the initiator exponent also varied in diluted systems, depending on the nature and proportion of the solvent, the variation being from a value of 0.5 in bulk system to zero or almost zero at about 25% (v/v) solvent concentration. Other kinetic parameters, viz., k_p²/k_t and the activation energy for polymerization, were determined and are reported. Kinetic and other evidence indicates that the photopolymerization takes place by a radical mechanism and termination is bimolecular in nature in bulk systems; in dilute systems, termination by initiator complex assumes predominance, particularly at high solvent concentrations (≥25% v/v).     

Photopolymerization of methyl methacrylate with the use of morpholine-chlorine charge transfer complex as the photoinitiator

Polymerization of methyl methacrylate (MMA) was kinetically studied under photo condition using near UV visible light at 40°C and employing morpholine (MOR)–chlorine (Cl₂) charge transfer (C-T) complex as the photoinitiator. The rate of polymerization (R_p) was dependent on morpholine/chlorine mole ratio; the 1 : 2 (MOR–Cl₂) C-T complex acted as the latent initiator complex, C, which underwent further complexation with the monomer molecules to give the actual initiator complex, I. Using 1 : 2 (MOR-Cl₂) C-T complex as the latent initiator, the initiator exponent evaluated for bulk photopolymerization of MMA was 0.071 and monomer exponent determined from studies of photopolymerization in benzene diluted system was 1.10. Benzoquinone behaved as a strong inhibitor and the polymers tested positive for the incorporation of chlorine atom end groups. Polymerization followed a radical mechanism. Kinetic nonideality as revealed by low (≪0.5) initiator exponent and a monomer exponent of greater than unity were explained in terms of primary radical termination effect. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1681–1687, 1997     

Ferrocene-containing polymers. II. Radiation-induced copolymerizations of ferrocenylmethyl methacrylate with styrene,methyl methacrylate,and ethyl acrylate

Ferrocenylmethyl methacrylate (FMMA) was copolymerized with styrene (St), methyl methacrylate (MMA), and ethyl acrylate (EA) in benzene solution at 25°C by γ radiation. The reactions proceeded by a free radical mechanism, and monomer reactivity ratios were derived by the Tidwell–Mortimer method for St(M₁)–FMMA(M₂), r₁ = 0.35 and r₂ = 0.46; for MMA(M₁–FMMA)(M₂), r₁ = 0.85 and r₂ = 1.36; for EA(M₁)–FMMA(M₂), r₁ = 0.36 and r₂ = 3.03. The Q and e values of FMMA determined from copolymerization with St were 0.97 and 0.55, respectively. Terpolymerization of a MMA–FMMA–EA system based on the Alfrey–Goldfinger equations was studied. This is a typical terpolymerization system in which reactivities of the monomers obey the Q–e scheme. Comparing the results obtained here with those previously reported for other monomers, we concluded that FMMA is one of the most highly reactive monomers among alkyl methacrylates.     

Polymerization of Methyl Methacrylate with Bis(Cyclopentadienyl)Titanium Dichloride in a Water-Methanol Mixture: Formation of Tetrahydrofuran-Insoluble Polymer

Abstract

Methyl methacrylate (MMA) was found to be effectively polymerized with bis(cyclopentadienyl)titanium dichloride (CP₂TiCl₂) in a water-methanol mixture (1:1, v/v). The polymerization proceeded heterogeneously because the resulting poly(MMA) was insoluble in the system. The rate (R _p) of the heterogenous polymerization was apparently expressed by R _p = k[Cp₂TiCl₂]²[MMA]^2˙5 (at 40°C). The resulting poly(MMA) was observed to consist of tetrahydrofuran (THF)-soluble and insoluble parts. In contrast with the usual radical poly(MMA), the THF-insoluble part was soluble in benzene, toluene, and chloroform but insoluble in polar solvents such as ethyl acetate, acetone, acetonitrile, dimethylformamide, and dimethylsulfoxide. The polymerization was found to be profoundly accelerated by irradiation with a fluorescent room lamp (15 W). The results of copolymerization of MMA and acrylonitrile indicated that the present polymerization proceeds through a radical mechanism.     

Iron-mediated AGET ATRP of styrene and methyl methacrylate using ascorbic acid sodium salt as reducing agent

Atom transfer radical polymerization of styrene(St) and methyl methacrylate(MMA) in bulk and in different solvents using activators generated by electron transfer(AGET ATRP) were investigated in the presence of a limited amount of air using FeCl3·6H2O as the catalyst, ascorbic acid sodium salt(AsAc-Na) as the reducing agent, and a cheap and commercially available tetrabutylammonium bromide(TBABr) as the ligand. It was found that polymerization in THF resulted in shorter induction period than that in bulk and in toluene for AGET ATRP of St, while referring to AGET ATRP of MMA, polymerization in THF showed three advantages compared with that in bulk and toluene: 1) shortening the induction period, 2) enhancing the polymerization rate and 3) having better controllability. The living features of the obtained polymers were verified by chain end analysis and chain-extension experiments.     

Synthesis,Characterization, and Application of Poly[Substituted Methylene]S

Radical polymerization of fumaric acid derivatives, such as dialkyl fumarates, gave polymers consisting of a less-or nonflexible substituted polymethylene structure. The yield and molecular weight of the polymers produced increased as the bulkiness of the ester substituents increased. For example, when di-t-butyl fumarate was polymerized in bulk with azocyclohexanecarbonitrile (20 mmol/L) at 80°C for 6 h, polymer with M _n of more than 100 000 was produced in more than 80% yield. The polymers obtained were colorless powders and did not melt before degradation at ～250°C, but they were soluble in such organic solvents as benzene, carbon tetrachloride, tetrahydrofuran, and dioxane. A transparent brittle film or fiber was obtained from toluene solution. Some properties and possibilities for application of these polymers are described and discussed.     

Atmospheric Hydrocarbon Concentrations in the Baltic Sea Area

Abstract

During a marine research expedition in 1983 in the Baltic Sea area air samples were collected for the analysis of several organic and inorganic pollutants. The aim of the expedition was to obtain information on the airborne load in the sea as well as to measure the concentrations of the pollutants far away from source areas. In this paper the background concentrations of the primarily traffic originated aromatic hydrocarbons benzene, toluene and xylenes will be presented.

The concentrations of benzene were from 0.2 to 2μg/m³, of toluene between 0.4–3μg/m³, of m-xylene 0.02–0.60μg/m³ while the concentrations of o-xylene were 0.01–0.1 μg/m³. The concentrations did not depend too much on the origin (continental/sea type) of the air masses. A weak minimum in the concentrations of the measured hydrocarbons was noticed in the central Baltic Sea area. When comparing lead concentrations in fine particles (< 2.5 μm) with those of benzene, toluene and m-xylene some coincidence between them could be observed.     

Polymerization of 4-phenyl-1-butyne catalyzed by metathesis and Ziegler–Natta catalysts

The polymerization of 4-phenyl-1-butyne was carried out using metathesis and Ziegler-Natta catalysts. Especially, the Fe(acac)₃-AlEt₃ catalyst with toluene as a solvent produced an extremely high molecular weight polymer of M_w ≈ 10⁶. Solubility of the polymers at room temperature in organic solvents such as benzene, toluene, dichloromethane, chloroform, and THF was excellent despite their high molecular weights. It has been indicated that the polymer prepared by the Fe(acac)₃-AlEt₃ catalyst is of cis form with a high stereoregularity. © 1993 John Wiley & Sons, Inc.     

“Living” radical polymerization of methyl methacrylate with diethyl 2,3-dicyano-2,3-diphenylsuccinate as a thermal iniferter

The bulk polymerization of methyl methacrylate (MMA) initiated with diethyl 2,3-dicyano-2,3-diphenylsuccinate (DCDPS) was studied. This polymerization showed some “living” characteristics; that is, both the yield and the molecular weight of the resulting polymers increased with reaction time, and the resultant polymer can be extended by adding MMA. The molecular weight distribution of PMMA obtained at high conversion is fairly narrow (M_w/M_n = 1.24≈1.34). It was confirmed that DCDPS can serve as a thermal iniferter for MMA polymerization by a “living” radical mechanism. Furthermore, the PMMA obtained can act as a macroinitiator for radical polymerization of styrene (St) to give a block copolymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4610–4615, 1999     

Kinetic study on the radical polymerization of 2‐methacryloyloxyethyl phosphorylcholine

Polymerization of 2‐methacryloyloxyethyl phosphorylcholine (MPC) was kinetically investigated in ethanol using dimethyl 2,2′‐azobisisobutyrate (MAIB) as initiator. The overall activation energy of the homogeneous polymerization was calculated to be 71 kJ/mol. The polymerization rate (R_p) was expressed by R_p = k[MAIB]^0.54±0.05 [MPC]^1.8±0.1. The higher dependence of R_p on the monomer concentration comes from acceleration of propagation due to monomer aggregation and also from retardation of termination due to viscosity effect of the MPC monomer. Rate constants of propagation (k_p) and termination (k_t) of MPC were estimated by means of ESR to be k_p = 180 L/mol · s and k_t = 2.8 × 10⁴ L/mol · s at 60 °C, respectively. Because of much slower termination, R_p of MPC in ethanol was found at 60 °C to be 8 times that of methyl methacrylate (MMA) in benzene, though the different solvents were used for MPC and MMA. Polymerization of MPC with MAIB in ethanol was accelerated by the presence of water and retarded by the presence of benzene or acetonitrile. Poly(MPC) showed a peculiar solubility behavior; although poly(MPC) was highly soluble in ethanol and in water, it was insoluble in aqueous ethanol of water content of 7.4–39.8 vol %. The radical copolymerization of MPC (M₁) and styrene (St) (M₂) in ethanol at 50 °C gave the following copolymerization parameters similar to those of the copolymerization of MMA and St; r₁ = 0.39, r₂ = 0.46, Q₁ = 0.76, and e₁ = +0.51. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 509–515, 2000     

Effect of benzophenone on the H2O2-induced photopolymerization of methyl methacrylate

Benzophenone (BP) in low concentrations (<0.001 mol 1^?1) produces a rate enhancing effect in the H₂O₂-induced bulk photopolymerization of MMA. R_p is proportional to [H₂O₂]^0.4 and [BP]^0.4, and $\text{k}{}_{\mathrm{p}}{}^2\text{k}{}_1$ at 30° is 1.00 × 10^?2 1.mol^?1 sec^?1. In diluted systems, different solvents produce different kinetic effects, reaction order with respect to monomer being negative for IPA and THF as solvent, positive but <1.0 for benzene and chloroform, 1.2 for acetonitrile, CCl₄ and t-butanol and 1.8 for DMA. The variable solvent effect is attributed to modification of the initiation process by the various solvents to different extents. Kinetic analysis of data for bulk photopolymerization gives evidence for primary radical termination and degradative initiator transfer.     

Photopolymerization of methyl methacrylate using hydrogen peroxide as the photoinitiator

Photopolymerization of MMA with the use of H₂O₂ as the photoinitiator under visible light at 30°C was studied. Kinetic features in bulk monomer and in the presence of different diluents differ significantly. Usual free radical kinetics with square-root dependence of rate on initiator, indicating bimolecular termination of chain radicals, were observed for bulk polymerization. On dilution with various solvents polymerization was found to be retarded to different (usual and more than usual) extents, the observed monomer exponent value being much higher than unity in many cases. This deviation from normal kinetics has been interpreted in terms of the predominance of degradative initiator transfer in the diluted systems.     

ATRP of methyl methacrylate initiated with a bifunctional initiator bearing bromomethyl functional groups: Synthesis of the block and graft copolymers

This article reports the synthesis of the block and graft copolymers using peroxygen‐containing poly(methyl methacrylate) (poly‐MMA) as a macroinitiator that was prepared from the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in the presence of bis(4,4′‐bromomethyl benzoyl peroxide) (BBP). The effects of reaction temperatures on the ATRP system were studied in detail. Kinetic studies were carried out to investigate controlled ATRP for BBP/CuBr/bpy initiating system with MMA at 40 °C and free radical polymerization of styrene (S) at 80 °C. The plots of ln ([M_o]/[M_t]) versus reaction time are linear, corresponding to first‐order kinetics. Poly‐MMA initiators were used in the bulk polymerization of S to obtain poly (MMA‐b‐S) block copolymers. Poly‐MMA initiators containing undecomposed peroygen groups were used for the graft copolymerization of polybutadiene (PBd) and natural rubber (RSS‐3) to obtain crosslinked poly (MMA‐g‐PBd) and poly(MMA‐g‐RSS‐3) graft copolymers. Swelling ratio values (q_v) of the graft copolymers in CHCl₃ were calculated. The characterizations of the polymers were achieved by Fourier‐transform infrared spectroscopy (FTIR), ¹H‐nuclear magnetic resonance (¹H NMR), gel‐permeation chromatography (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), and the fractional precipitation (γ) techniques. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1364–1373, 2010     

Synthesis of poly(methyl methacrylate) macromonomer

Anionic polymerization of methyl methacrylate (MMA) was carried out in tetrahydrofuran (THF) or THF/toluene mixture at ?78°C initiated by triphenylmethyl sodium or lithium as initiators. Highly syndiotactic PMMA of low polydispersity (M _w/m _n = 1.11–1.17) could be prepared with triphenylmethyl lithium in THF or THF/toluene mixture at ? 78°C. Moreover, PMMA macromonomer having one vinylbenzyl group per polymer chain was prepared by the couplings of living PMMA initiated by triphenylmethyl lithium with p-chloromethyl styrene (CMS) at ?78°C. The coupling reaction of living PMMA initiated by triphenylmethyl sodium with CMS was scarcely occurred.