Eine quantitative,UV-photometrische bestimmung von Endgruppen in polystyrolen

Styrene was polymerized in bulk for 45 min at 70°C under a nitrogen atmosphere to a conversion of 6.16 weight-percent with an aliphatic azo compound, which contained four p-methoxyphenyl groups per molecule. The polystyrene could be purified easily by column chromatography and was then free of initiator and its decomposing products. It was separated into ten fractions by fractional precipitation (toluene/methanol), and the molecular weights of the polystyrenes were determined osmotically. The ultraviolet absorptions of the polystyrene solutions in dioxane were optically constant and followed the Bouguer-Lambert-Beer law. This made it possible to determine the number of absorbing groups per polystyrene molecule, which were constant with a value of 2. Polystyrenes with a number average molecular weight to 10⁶ should be determinable in the same way.     

Effects of iron(III) chloro complexes on the polymerization of styrene

The polymerization of styrene initiated by 2,2′-azobisisobutyronitrile has been studied in N,N-dimethylformamide solution at 60°C in the presence of hexakis(N,N-dimethylformamide) iron(III) tetrafluoroborate alone, and also in the presence of added lithium chloride. The presence of Fe(DMF)₆³⁺ ions in the polymerizing systems caused retardation, but iron(III) chloro complexes produced well defined inhibition periods. Velocity constants at 60°C for polystyryl radicals towards Fe(DMF)₆³⁺, Fe(DMF)₅Cl²⁺, Fe(DMF)₄Cl₂⁺, and FeCl₄^? ions were calculated to be 847, 4.15 × 10⁴, 6.55 × 10⁴, and 3.14 × 10⁴ l./mole-sec, respectively. Values of the initiator efficiency f for most systems investigated ranged from 0.59 to 0.62.     

Solvation effect in thermal decomposition of 2,2′-azoisobutyronitrile on the N,N-dimethylformamide/methyl methacrylate system

The thermal decomposition rate constant of AIBN (??_d) in N,N-dimethylformamide (DMF)/methyl methacrylate (MM) mixtures of various compositions at 60°C is studied. The ??_d value is 6.45 × 10^?4min^?1 for pure DMF and 7.20 × 10^?1 min^?1 for pure methyl methacrylate. The ??_d values of DMF/MM mixtures were found to be dependent on the mixture composition. This dependence is not a linear function of the monomer mole fraction, but has a minimum at ca. 20 30 mol% of MM. The relationship between the AIBN decomposition rate constant and the monomer mole fraction was interpreted on the basis of solvation of the initiator molecules. © 1995 John Wiley & Sons, Inc.     

Radical polymerization of vinyl thiocyanatoacetate: Participation of group‐transfer mechanism

Vinyl thiocyanatoacetate (VTCA) was synthesized, and its radical polymerization behavior was studied in acetone with dimethyl 2,2′‐azobisisobutyrate (MAIB) as an initiator. The initial polymerization rate (R_p) at 60 °C was expressed by R_p = k[MAIB]^0.6±0.1 [VTCA]^1.0±0.1 where k is a rate constant. The overall activation energy of the polymerization was 112 kJ/mol. The number‐average molecular weights of the resulting poly (VTCA)s (1.4–1.6 × 10⁴) were almost independent of the concentrations of the initiator and monomer, indicating chain transfer to the monomer. The chain‐transfer constant to the monomer was estimated to be 9.6 × 10^?3 at 60 °C. According to the ¹H and ¹³C NMR spectra of poly (VTCA), the radical polymerization of VTCA proceeded through normal vinyl addition and intramolecular transfer of the cyano group. The cyano group transfer became progressively more important with decreasing monomer concentration. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 573–582, 2002; DOI 10.1002/pola.10137     

Association of polyacrylonitrile prepared by low-temperature,solution polymerization with an organometallic catalyst

The weight-average molecular weights of polymers of acrylonitrile prepared by a free-radical initiator and an organometallic catalyst have been determined by lightscattering measurements in N,N-dimethylformamide, dimethyl sulfoxide, and dimethylacetamide at 25°C. and in dimethyl sulfoxide at 140°C. The apparent molecular weights of the polymers prepared with the NaAlEt₃S(i-Pr) catalyst in DMF at ?78°C. (referred to as high-melting polymers) changed from 54,800, 82,700, and 480,000 when measured in DMF at 25°C. to 36,000, 41,600, and 225,000 when measured in DMSO at 140°C., whereas the molecular weights of the free-radical polymers remained unchanged. Furthermore, from results obtained in DMSO at 140°C., The intrinsic viscosity–molecular-weight relationships were found to be identical for the high-melting and the free-radical polymer and in substantial agreement with an equation reported by Cleland and Stockmayer. The apparent decrease in molecular weight of the high-melting polymer from 25 to 140°C. indicates rather clearly that the high-melting polymers are associated in DMF at 25°C. The “aggregates,” even though present only at low concentrations, raised the weight-average molecular weight markedly but affected the number-average molecular weight only slightly, thus giving a high M?_w/M?_n ratio. It appears likely that when temperature and solvent are such that association does not occur, linear PAN's will have approximately the same intrinsic viscosity–molecular weight relationship (subject of course to slight change by polydispersity). The often reported abnormal molecular weight of samples prepared by solution polymerization especially at low temperatures, may be attributed to branching, or to an association, as reported here. The nature of association of PAN in dilute solution is also discussed.     

Initiator efficiency of 2,2′‐azobis(isobutyronitrile) in bulk dodecyl acrylate free‐radical polymerizations over a wide conversion and molecular weight range

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(21) 5559 . The initiator efficiency, f, of 2,2′‐azobis(isobutyronitrile) (AIBN) in dodecyl acrylate (DA) bulk free‐radical polymerizations has been determined over a wide range of monomer conversion in high‐molecular‐weight regimes (M_n ? 10⁶ g mol^?1 [? 4160 units of DA)] with time‐dependent conversion data obtained via online Fourier transform near infrared spectroscopy (FTNIR) at 60 °C. In addition, the required initiator decomposition rate coefficient, k_d, was determined via online UV spectrometry and was found to be 8.4 · 10^?6 s^?1 (±0.5 · 10^?6 s^?1) in dodecane, n‐butyl acetate, and n‐dodecyl acetate at 60 °C. The initiator efficiency at low monomer conversions is relatively low (f = 0.13) and decreases with increasing monomer to polymer conversions. The evolution of f with monomer conversion (in high‐molecular‐weight regimes), x, at 60 °C can be summarized by the following functionality: f^{60 °C} (x) = 0.13–0.22 · x + 0.25 · x² (for x ≤ 0.45). The reported efficiency data are believed to have an error of >50%. The ratio of the initiator efficiency and the average termination rate coefficient, 〈k_t±, (f/〈k_t〉) has been determined at various molecular weights for the generated polydodecyl acrylate (M_n = 1900 g mol^?1 (? 8 units of DA) up to M_n = 36,500 g mol^?1 (? 152 units of DA). The (f/〈k_t〉) data may be indicative of a chain length‐dependent termination rate coefficient decreasing with (average) chain length. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5170–5179, 2004     

SET–LRP of N‐isopropylacrylamide in the presence of chain transfer agent

In this study, single electron transfer‐living radical polymerization (SET–LRP) of N‐isopropylacrylamide (NIPAM) in the presence of 2‐mercaptoethylamine chain transfer agent (CTA) was carried out by Cu(0) generated in situ from the disproportionation of CuBr/2,2′‐bipyridine (2,2′‐bpy) in N,N‐dimethylformamide (DMF) at 90 °C. Analysis of polymerization kinetics in the presence of CTA showed that the premature termination of growing polymer chains leads to retardation. The apparent rate constant of polymerization (k) decreased from 4.49 × 10^?4 to 2.59 × 10^?4 min^?1 with increasing CTA concentration. The initiator efficiency (I_eff) and the chain transfer constant (C_s) were found to be 0.524 and 0.286, respectively. The molecular weights of poly(N‐isopropylacrylamide) [poly(NIPAM)] produced were significantly higher than the predicted values, and the polydispersities were less than 1.22. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Chain transfer for vinyl monomers polymerized in N-allylstearamide

Apparent transfer constants have been determined for styrene, methyl methacrylate vinyl acetate, and diethyl maleate polymerized in N-allylstearamide at 90°C. Regression coefficients for transfer were: methyl methacrylate, 0.301 × 10^?3; styrene, with no added initiator, 0.582 × 10^?3; styrene, initiated with benzoyl peroxide, 0.830 × 10^?3; vinyl acetate, 62.01 × 10^?3; and diethyl maleate, 2.24 × 10^?3. Rates of polymerization were retarded for both styrene and methyl methacrylate. Vinyl monomer and comonomer disappearance followed an increasing exponential dependence on both initiator and monomer concentration. Although degradative chain transfer probably caused most of the retardation, the cross-termination effect was not eliminated as a contribution factor. Rates for the vinyl acetate copolymerization were somewhat retarded, even though initiator consumption was large because of induced decomposition. The kinetic and transfer data indicated that the reactive monomers added radicals readily, but that rates were lowered by degradative chain transfer. Growing chains were terminated at only moderate rates of transfer. Unreactive monomers added radicals less easily, producing reactive radicals, which transferred rapidly, so that molecular weights were lowered precipitously. Although induced initiator decomposition occurred, rates were still retarded by degradative chain transfer. A simple empirical relation was found between the reciprocal number-average degree of polymerization, 1/X?_n1 and the mole fraction of allylic comonomer entering the copolymer F₂, which permitted estimation of the molecular weight of copolymers of vinyl monomers with allylic comonomers. This equation should be applicable when monomer transfer constants for each homopolymer are known and when osmometric molecular weights of one or two copolymers of low allylic content have been determined.     

End‐functionalized polystyrene by ATRP: A facile approach to primary amino and carboxylic acid terminal groups

Monoamino‐terminated and monocarboxylic acid‐terminated polystyrenes containing active halogenated end groups were prepared by atom transfer radical polymerization (ATRP) using the so‐called initiator method and protective group chemistry. α‐Chloropropionates were synthesized and utilized as initiators containing the tert‐butoxycarbonyl (t‐BOC)‐protected amino and the tert‐butyl (t‐Bu)‐protected carboxylic acid function, respectively. Optimum polymerization conditions were attained using CuCl/N,N,N′,N′′,N′′‐pentamethyldiethylenetriamine (PMDETA) as catalyst and 10 vol % n‐butanol as homogenizing agent at 110 °C. However, targeting larger quantities an alternative route was established employing 50 vol % N,N‐dimethylformamide (DMF). Subsequent hydrolysis of the ω‐tert‐butoxycarbonyl polystyrenes afforded well‐defined polymers with quantitative deprotection of the functional groups. Comparatively, thermolytic cleavage of the protective sites was studied. ¹H NMR verified the quantitative removal of the t‐BOC‐protecting groups. Furthermore, the resulting α‐amino‐ω‐chloro polystyrenes were reacted with Sanger reagent to confirm the existence of the thereby converted primary amino groups. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3845–3859, 2009     

Dilute-solution properties of ring polystyrenes

The temperature Θ_A2 at which the second virial coefficient A₂ is zero for ring polystyrenes is 28.5°C in cyclohexane, independent of molecular weight in the range 2 × 10⁴ to 4.5 × 10⁵. This cannot be explained solely by the Candau–Rempp–Benoit theory, which takes into account the effect of segment density on Θ_A2 The radius of gyration of a ring is found to be approximately one-half that of a linear polymer with the same molecular weight. The intrinsic viscosities [η] and intrinsic translational friction coefficients [f] of ring polystyrenes with molecular weights ranging from 7 × 10³ to 4.5 × 10⁵ have been measured in cyclohexane at 34.5°C (Θ, the Flory theta temperature for linear polystyrenes) and in toluene (a good solvent). The results are compared with those for linear polystyrene. It is found that the Mark–Houwink exponent is less than one-half in cyclohexane at Θ. In toluene it is 0.67 compared to 0.73 for linear polystyrene. The hydrodynamic measurements suggest that large rings are less expanded than the linear polymers with the same molecular weight, contrary to many predictions.     

Aqueous polymerization of acrylamide initiated by oxygenated cobalt(III) triethylenetetramine complex

Polymerization of acrylamide was thermally initiated by the oxygenated cobalt( III ) triethylenetetramine complex. Rate, conversion, and molecular weights obtained are favorable comparable to those initiated by K₂S₂O₄ and K₂S₂O₈ initiators. An induction period is about 3 mins. The value of K_df at 60°C is 6.75 × 10^?5 s^?1, and the chain transfer to monomer constant is 1.2 × 10^?5. The rate dependence obtained are a half order on the initiator concentration and a 1.38 order on the monomer concentration. The mole fraction of combination termination occurred in the overall termination reactions evaluated is 0.746.     

Stimuli‐responsive 4‐acryloylmorpholine/4‐acryloylpiperidine copolymers via nitroxide mediated polymerization

4‐acryloylmorpholine/4‐acryloylpiperidine statistical copolymers were synthesized by nitroxide mediated polymerization (NMP) with BlocBuilder unimolecular initiator in dimethylformamide solution at 120 °C. The copolymers had narrow molecular weight distributions (dispersity ? = 1.25–1.35, number average molecular weights M _n = 8.5–13.7 kg mol^?1). The copolymer microstructure was essentially statistical (reactivity ratios r _4AP = 0.81 ± 0.73, r _4AM = 0.73 ± 0.68 based on non‐linear fitting of the Mayo‐Lewis equation). Cloud point temperatures (CPT) in aqueous media were tuned from 11 °C to 92 °C, merely by adjusting the initial monomer composition. Using NMP permitted sharper control of the CPT transitions, compared to the similar copolymer made using conventional radical polymerization. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2160–2170     

Characterization of Branched Poly (vinyl Acetate) by GPC and Low Angle Laser Light Scattering Photometry

Abstract

Poly (vinyl acetate), PVAC, synthesized by bulk polymerization over a range of initiator concentrations ([AIBN] = 10^?5 to 4 × 10^?3 g-mole/1), temperatures (50°C, 60°C, 70°C, and 80°C) and conversion levels (3 to > 90%) were characterized using low angle laser light scattering (LALLS) photometry to measure M_w of the whole polymers. A number of these samples were characterized using GPC with a differential refractive index (DRI) and LALLS detector to measure the molecular weight distribution (weight fraction versus M_w). M_w for PVAC samples synthesized at suitably low initiator levels at various conversions were found to agree with classical light scattering measurements after Graessley.

An electronic device and a technique which optimizes the sensitivity and the signal-to-noise ratio of the LALLS photometer throughout the molecular weight distribution (MWD) of the GPC chromatogram were devised. These considerably simplify the operation of the LALLS for both offline and online operation with GPC.

Most importantly it was unambiguously shown that the commonly used universal calibration parameter (UCP) with GPC, [n]M_w, is incorrect for polymers with molecules having the same hydrodynamic volume but different molecular weights, i. e., those with only chain branching (LCB), copolymers with compositional drift, and polymer blends. The correct UCP was found to     

Styrene/maleimide copolymer with stable second-order optical nonlinearity

Radical copolymerization of N-(azo dye) maleimide or N-(substituted phenyl) maleimide and styrene were carried out using 2,2′-azobis-isobutyronitrile as an initiator in THF at 60°C. These copolymers exhibit high solubility in most of the organic solvents and excellent thermal stability up to 280°C under nitrogen atmosphere. The copolymer films which were heated at 200–240°C under high corona field exhibit d₃₃ = 3–5 pm/V, in the Maker-fringe measurement. Experimental results also showed that the copolymer with azo dye as chromophore did not decay in second harmonic response even at 130°C. © 1996 John Wiley & Sons, Inc.     

Effect of Oxygen on the Polymerization of Vinyl Chloride

The effects of oxygen on the liquid-phase polymerization of vinyl chloride at 55°C in the presence of an added initiator, bis(4-tert-butylcyclohexy1) peroxydicarbonate, (Perkadox 16), have been studied by tumbled dilatometry. A conventional kinetic scheme involving a predominant cross-termination reaction is proposed to explaine the dependence of the induction period on initial oxygen concentration and initiator concentration. The degree of conversion of the initial oxygen to peroxidic compounds did not exceed 30% by weight under any experimental conditions employed, and the existence of other oxidation products such as formaldehyde, carbon monoxide, and methanol has been demonstrated. Radical decomposition reactions may produce some of the oxidation products. At 55°C, the average velocity constant for decomposition of vinyl chloride polyperoxides in dichloromethane solution was 8 × 10^?5 sec^?1 compared with 6.6 × 10^?5 sec^?1 for Perkadox 16. Perkadox 16 has been used as an initiator in a dilatometric study of the homogeneous polymerization of styrene at 60°c. Molecular weights of the polymers were determined viscometrically or by the use of gel-permeation chromatography. The results indicate that no transfer to initiator occurs in this systems.     

Synthesis,characterization, and photoresponsive behavior of new azobenzene‐containing polyethers

Two new polyethers, bearing azobenzene moiety in the side chain, were synthesized in excellent yields by means of anionic polymerization of 4‐glycidyloxyazobenzene and 4‐cyano‐4′‐glycidyloxyazobenzene (leading to azo‐P1 and azo‐P2 polymers, respectively) with the system polyiminophosphazene base t‐Bu‐P₄/3,5‐di‐tert‐butylphenol as initiator. The polymers were characterized with respect to their molecular weights, structure, and calorimetric features. The polyether bearing cyanoazobenzene group in the side chain was found to exhibit nematic phase up to 200 °C. E–Z isomerization of both polymers in tetrahydrofuran solution, after irradiating with UV light at 364 nm for 15 min, was investigated by means of UV–visible absorption spectroscopy. In the case of glycidylic monomers as well as the resulting polymers, E–Z isomerization was also investigated by means of ¹H NMR, by direct irradiation in the NMR probe in deuterated 1,1,2,2‐tetrachloroethane solution. By this technique, in the case of 4‐cyano‐4′‐glycidyloxyazobenzene, it was found that irradiation led to a photostationary state corresponding to an amount of Z isomer equal to 25%. For azo‐P1 polymer, Z–E or “reverse” isomerization was investigated at 60, 70, or 80 °C directly in the NMR probe; as expected, the process followed a first‐order rate law. The kinetic constants as well as the activation energy for the process were determined in this temperature range. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5426–5436, 2009     

Radical‐initiated polymerization of β‐methyl‐α‐methylene‐γ‐butyrolactone

β‐Methyl‐α‐methylene‐γ‐butyrolactone (MMBL) was synthesized and then was polymerized in an N,N‐dimethylformamide (DMF) solution with 2,2‐azobisisobutyronitrile (AIBN) initiation. The homopolymer of MMBL was soluble in DMF and acetonitrile. MMBL was homopolymerized without competing depolymerization from 50 to 70 °C. The rate of polymerization (R_p) for MMBL followed the kinetic expression R_p = [AIBN]^0.54[MMBL]^1.04. The overall activation energy was calculated to be 86.9 kJ/mol, k_p/k_t^1/2 was equal to 0.050 (where k_p is the rate constant for propagation and k_t is the rate constant for termination), and the rate of initiation was 2.17 × 10^?8 mol L^?1 s^?1. The free energy of activation, the activation enthalpy, and the activation entropy were 106.0, 84.1, and 0.0658 kJ mol^?1, respectively, for homopolymerization. The initiation efficiency was approximately 1. Styrene and MMBL were copolymerized in DMF solutions at 60 °C with AIBN as the initiator. The reactivity ratios (r₁ = 0.22 and r₂ = 0.73) for this copolymerization were calculated with the Kelen–Tudos method. The general reactivity parameter Q and the polarity parameter e for MMBL were calculated to be 1.54 and 0.55, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1759–1777, 2003     

Solution properties of high molecular weight polystyrene

A series of polystyrenes with weight-average molecular weight M?_w up to 1.3 × 10⁷ was prepared by anionic polymerization in tetrahydrofuran (THF). Each sample was characterized by gel-permeation chromatography, light scattering, and viscometry. It was found that each sample had an almost symmetrical and very narrow molecular weight distribution (M?_w/M?_n < 1.07). The mean-square unperturbed radius of gyration 〈S²〉₀ was determined in trans-decalin at 20.4°C as 〈S²〉₀ = 7.8₆ × 10^?18M?_w (cm²). The particle scattering factor was well represented by the Debye equation irrespective of solvent in the range of M?_w < 4 × 10⁶, and only a small deviation was observed in benzene at higher molecular weights. The penetration function Ψ ≡ A₂M²/4π^3/2N_A〈S〉^23/2 was found to approach a relatively low asymptotic value of 0.21–0.23 at molecular weights above 2 × 10⁶ in benzene at 30°C, where A₂ is the second virial coefficient and N_A is Avogrado's number. It was also found that the theta temperature in trans-decalin was affected by the nature of polymer samples. A difference of about 3°C in the theta temperature was observed between two series of anionic polystyrenes, one prepared in THF and the other in benzene, but there was practically no difference in unperturbed chain dimension.     

13C-NMR spectroscopic analysis of vinyl groups in styrene–divinylbenzene networks

p-Divinylbenzene (DVB) ¹³C-labeled at the methine carbon of the vinyl group was copolymerized in suspension with styrene at 70, 70–95, and 135–155°C using 2,2′-azobisisobutyronitrile (AIBN) as the initiator. The number of unreacted vinyl groups in each copolymer was determined by ¹³C CP–MAS NMR analysis of solid samples, direct polarization ¹³C-NMR analysis of CDCl₃-swollen gels, and bromination. Results from the three methods agree methods agree qualitatively. Even the 1% DVB-crosslinked networks contained 40% unreacted DVB-vinyl groups when prepared by high conversion polymerization at 70°C and 16% unreacted DVB-vinyl groups when polymerization was finished at 95°C. The analyses were also applied to some commercial crosslinked polystyrenes. Every sample examined contained pendent vinyl groups     

Synthesis,spectroscopic and thermodynamic studies of new transition metal complexes with N,N′-bis(2-hydroxynaphthalin-1-carbaldehydene)-1,2-bis(m-aminophenoxy)ethane and their determination by spectrophotometric methods

A novel tetradentate N₂O₂-type Schiff base, synthesized from 1,2-bis(m-aminophenoxy)ethane and 2-hydroxynaphthalin-1-carbaldehyde, forms stable complexes with transition metal ions such as Cu(II), VO(IV) and Zn(II) in DMF. Microanalytical data, elemental analysis, magnetic measurements, UV, visible and IR spectra as well as conductance measurements were used to confirm the structures. The stability constants of these complexes in 60% (v/v) DMF–water were determined at different ionic strengths (0.07,?0.13,?0.2?M) and at different temperatures (45,?50,?55,?60?±?0.1°C) using a spectrophotometric method. From these constants, thermodynamic stability constants and thermodynamic parameters (ΔG?⁰, ΔH?⁰, ΔS?⁰) were calculated. The values of enthalpy change are negative for all systems. The acid dissociation constant of the ligand, investigated in 60% (v/v) DMF–water, has also been calculated at different temperatures.