Averaging the electrical properties of fiber-reinforced metal composites

Using the regular structure model, we average the electrical properties of unidirectional fiber-reinforced metal composites and propose procedures for determination of the effective electrical conductivity tensor of these materials. For the general case of packing of fibers of arbitrary cross section, the problem is reduced to calculation of some functionals determined in solutions of the integral equation of the corresponding boundary current problem for the structure. In the special case of symmetric packing of fibers of circular cross section, the solution is written in the form of series in elliptic functions.Translated from Mekhanika Kompozitnykh Materialov, Vol. 31, No. 4, pp. 533–539, July–August, 1995.     

Averaging of electrical properties of anisotropic fiber-metal composites

The electrical properties of fiber-metal composites with anisotropic components were averaged within the framework of a regular structure model. The corresponding current problem was reduced to a system of two integral equations with elliptical kernels. The effective electrical conductivity tensor of such materials was defined as several functionals based on integral equation solutions for the boundary problem. The calculation results are given.Translated from Mekhanika Kompozitnykh Materialov, Vol. 33, No. 2, pp. 263–268, March–April, 1997.     

Predicting the elastoplastic response of fiber-reinforced metal matrix composites

This paper aims to investigate the effect of microstructure parameters (such as the cross-sectional shape of fibers and fiber volume fraction) on the stress–strain behavior of unidirectional composites subjected to off-axis loadings. A micromechanical model with a periodic microstructure is used to analyze a representative volume element. The fiber is linearly elastic, but the matrix is nonlinear. The Bodner–Partom model is used to characterize the nonlinear response of the fiber-reinforced composites. The analytical results obtained show that the flow stress of composites with square fibers is higher than with circular or elliptic ones. The difference in the elastoplastic response, which is affected by the fiber shape, can be disregarded if the fiber volume fraction is smaller than 0.15. Furthermore, the effect of fiber shape on the stress–strain behavior of the composite can be ignored if the off-axis loading angle is smaller than 30°.     

Pultrusion mechanics of fiber-reinforced thermoplastic composites

The associated problem of the rheology of a thermoplastic polymer melt during the pultrusion of fiber-reinforced composites in a plane-slotted die is resolved. The permeabilities of a stochastic fibrous system are determined for the case of a nonlinear (exponential) rheological model of the melt. The pressure distribution in the pultrusion tool is calculated with allowance for the permeability of the fibrous system. The dependence of the pultrusion force on the viscous properties of the melt and on the pull rate of the fibrous layer is established.Paper to be presented at the Ninth International Conference on the Mechanics of Composite Materials, Riga, October, 1995.Translated from Mekhanika Kompozitnykh Materialov, Vol. 31, No. 4, pp. 547–554, July–August, 1995.     

Realization of the mechanical properties of fibers in high-modulus polymer composites

The effect of scatter in the strength and deformation properties of the high-modulus fibers, the degree of twist, and the presence of pores in the polymeric matrix on the degree of realization of the potential possibilities of these fibers in composite materials is briefly considered.All-Union Scientific-Research Institute of Aviation Materials, Moscow. Translated from Mekhanika Polimerov, No. 6, pp. 1123–1125, November–December, 1972.     

Estimation of interface damage of fiber-reinforced composites

The estimation of interface damage of fiber-reinforced composites based on the propagation constants of coherent waves is studied in this paper. First, the relation between the interface damage and the propagation constants is investigated by using the theory of multiple scattering. Next, single and multiple scatterings in the composites in the case of incident P, SV, and SH waves are considered. The propagation constants of coherent waves are computed numerically, and the influence of interface damage on them is discussed. Then, based on the relation between the propagation constants and the interface damage, an inverse method to estimate the interface damage is proposed. Finally, a numerical example is given. The numerical results are obtained by using synthetic experimental data and the genetic algorithm. It is shown by the numerical example that the interface damage can be approximately estimated from the wave propagation constants measured with various degrees of accuracy.     

Predicting the onset of delamination in layered fiber-reinforced composites

In this paper, composite structures are considered which consist of several layers of carbon fiber reinforced plastics (CFRP). For such layered composite structures, delamination constitutes one of the major failure modes and hence predicting its initiation is essential for their design. Evaluating stress-strength relation based onset criteria requires an accurate representation of the through-the-thickness stress distribution, which can be particularly delicate in the case of shell-like structures. Thus, in this paper, a solid-shell finite element is utilized, which allows for incorporating a fully three-dimensional material model, still being suited for application to thin structures. Moreover, locking phenomena are cured by using both the EAS and the ANS concept, and numerical efficiency is ensured through reduced integration. The proposed anisotropic material model accounts for the material's micro-structure by using the concept of structural tensors. (© 2013 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)     

Averaging the physical properties of fibrous piezocomposites

Elastic, piezoelectric, and dielectric properties of fibrous composites with piezoelectric components are averaged for antiplane strains. Methods for determining coupled electroelastic fields in piezocomposites are proposed. Calculation results of the effective physical characteristics of some composites are given.Sumskii State University, Ukraine. Translated from Mekhanika Kompozitnykh Materialov, Vol. 34, No. 1, pp. 116–123, January–February, 1998.     

Inelastic deformation and fracture of disordered fiber-reinforced composites

Conclusions Simulation of the process of nonlinear deformation and failure in the structure of a unidirectional epoxy glass plastic under transverse loading has indicated that equilibrium regions of failure receiving only hydrostatic compressive loading may form. The development of this region explains the high (up to 40%) nonlinearity of deformation diagrams under transverse biaxial compressive loading. The regions of nonlinear deformation of the epoxy matrix affect less markedly the nonlinearity of the macroscopic s* diagrams. This fact and also the formation and avalanchelike propagation of regions of complete failure explain the linear form of many diagrams corresponding to tensile and shear loading in the transverse plane. The relations of the nonlinear theory of elasticity make it possible to describe with sufficient accuracy the entire set of the calculated diagrams.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 5, pp. 621–628, September–October, 1993.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 5, pp. 621–628, September–October, 1993.     

Interlaminar fracture toughness of graphite fiber-reinforced polyimide composites

Conclusion The present study has proved the effectiveness of the application of viscoelastic polymers with increased fracture toughness to graphite/polyimide composites interlaminar fracture toughness improvement. Thermoplastic polysulphone film and thermoresistant structural adhesive have proved to be inherently more effective for composites' delamination resistance growth than maleimide resin toughening and structural modification. The former inevitably results in increase of the honeycomb delamination resistance (Fig. 1) and its durability.Published in Mekhanika Kompozitnykh Materialov, Vol. 30, No. 6, pp. 848–852, November–December, 1994.     

Analysis of elastomeric composites based on fiber-reinforced systems 3. Two-directional composites

Results of investigation of deformation of elastomeric composite materials with a two-directional reinforcement scheme are presented. The study is performed on the basis of a structural macroscopic theory. The matrix of the composites analyzed is of a poorly compressible material. The fibers of both reinforcing systems are simulated as compressible bodies. Dependences of the parameters of tensile and shear strains on the strain values for different geometries of fiber arrangement are obtained.State Metallurgical Academy of Ukraine, Dnepropetrovsk, Ukraine. Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 4, pp. 479–492, May–June, 1999.     

Analysis of elastomeric composites based on fiber-reinforced systems. 2. Unidirectional composites

The elastic properties of unidirectionally reinforced composite materials under large deformations are studied. The applied model for deformation of materials is based on the structural macroscopic theory of stiff and soft composites, including micro- and macromechanical levels of analysis of composite media. The properties of unidirectional elastomeric composites are studied in tension and shear in the plane of reinforcement. The microscopic fields in the structural components of composites having poorly compressible and compressible matrices are also analyzed. Changes in the parameters of macroscopic deformation of the composites are examined as functions of the loading parameters and initial conditions of the structure. The evolution of the structural changes in deformed composite materials is described.State Metallurgical Academy of Ukraine, Dnepropetrovsk, Ukraine. Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 1, pp. 29–50, January–February, 1999.     

Regulation of the mechanical properties of thermoplastic carbon fiber-reinforced plastics by changing their production conditions and surface treatment of the fibers

The effect of technological parameters of processing and surface treatment of carbon fibers on the mechanical properties of carbon fiber-reinforced plastics (CFRPs) was investigated. The copolymer of 1,3,5-trioxane with 1,3-dioxolane was used as the polymer matrix, and medium-modulus hydrated cellulose Ural LO-24 carbon fibers served as the reinforcing filler. The polymer matrix was mixed with the carbon fibers by the method of combined extrusion. The dependence of the mechanical properties of CFRPs on the technological parameters of screw-disk extrusion was studied. It was found that the properties of the composites were greatly affected by the size of the working disk gap, the disk rotation rate, and the temperature in the zone of normal stresses. The surface of the carbon fibers was activated with atmospheric oxygen in the temperature range of 450–600°C, with mass loss of the fibers no greater than 3–4%. A 30–40% increase in the mechanical properties of the CFRPs was achieved. A decrease in the melt index of the 1,3,5-trioxane copolymer with 1,3-dioxolane reinforced with oxidized carbon fibers was observed, which should be taken into account in processing the composites into products. Introduction of carbon fibers in the 1,3,5-trioxane copolymer with 1,3-dioxolane allows us to increase the wear resistance and decrease the friction coefficient, which makes it possibile to use these materials in the friction units of machines and mechanisms, such as plain bearings, gears, and flange packings.Presented at the 10th International Conference on the Mechanics of Composite Materials (Riga, April 20–23, 1998).Ukrainian State University of Chemical Technology, Dnepropetrovsk, Ukraine. Translated from Mekhanika Kompozitnykh Materialov, Vol. 34, No. 5, pp. 673–682, September–October, 1998.     

Generalized self-consistent method: Modeling and computation of effective elastic properties of composites with composite or hollow inclusions

A new approach to the generalized self-consistent method [1,2] has been developed for problems of the statistical mechanics of composites with composite or hollow inclusions. The approach can reduce the problem of predicting the effective elastic properties of composites to a simpler averaged problem of a single, composite, or hollow inclusion with inhomogeneous elastic surrounding in a homogeneous effective elastic medium. The problem of predicting the effective elastic properties of composites with unidirectional hollow fibers or hollow spherical inclusions are studied by using the new approach.Submitted to the 10th International Conference on Mechanics of Composite Materials, April 20–23, 1998, Riga, Latvia.Perm' State Technical University, Russia. Translated from Mekhanika Kompozitnykh Materialov, Vol. 34, No. 2, pp. 173–183, March–April, 1998.     

The effect of carbon fibers and carbon nanotubes on the mechanical properties of polyimide composites

In this experimental work, the influence of carbon fibers (CFs) added to polyimide (PI) composite plastics was investigated. Also, the effect of carbon nanotubes (CNTs) on the fiber-matrix interface was studied. The results obtained show that the mechanical properties of CF/CNT/PI nanocomposites are superior to those of CF/PI composites.