Adhesion of polyether-modified poly(acrylic acid) to mucin

Pluronic-PAA, a thermogelling copolymer composed of side chains of poly(acrylic acid) (PAA) grafted onto a backbone of Pluronic copolymer, is of interest as a vehicle for the controlled release of compounds. An important feature of such a vehicle is its bioadhesive/mucoadhesive properties, which in the case of Pluronic-PAA are significant due to the presence of the PAA side chains. An atomic force microscopy (AFM) method has been developed and utilized to investigate the interactions between a Pluronic-PAA-modified microsphere and mucous substrates. The bioadhesive force was successfully measured, and trends were observed under conditions of varying pH and ionic strength. Pluronic-PAA exhibits significant mucoadhesion over a range of pH values, with mucoadhesion being optimal at pH 4-5 (adhesive force approximately 80 mN/cm(2)) and dropping sharply at higher pH, to a value of approximately 20 mN/cm(2) at pH 8. The mucoadhesive force decreased with increasing ionic strength, from a value of approximately 80 mN/cm(2) in 0.025 M NaCl to approximately 25 mN/cm(2) in 1.0 M NaCl. These results have been interpreted in terms of the effect of changing pH and ionic strength on electrostatic interactions and swelling of the polymer and mucin layers. Tensiometric force measurements indicated that hydrophobic interactions, as well as hydrogen bonding and electrostatic interactions, were significant in the mucoadhesion of Pluronic-PAA copolymers. Experiments with a range of Pluronic-PAA copolymers with varying PPO contents in the Pluronic segments showed that increasing the overall PPO content increased the hydrophobicity of the polymer solutions. This was reflected in the increases in the advancing contact angles with the mucin layer, indicating that hydrophobic interactions play a role in the adhesion of Pluronic-PAA to mucin.     

A physico-chemical investigation of poly(ethylene oxide)-block-poly(L-lysine) copolymer adsorption onto silica nanoparticles

The adsorption behavior of poly(ethylene oxide)-b-poly(L-lysine) (PEO(113)-b-PLL(10)) copolymer onto silica nanoparticles was investigated in phosphate buffer at pH 7.4 by means of dynamic light scattering, zeta potential, adsorption isotherms and microcalorimetry measurements. Both blocks have an affinity for the silica surface through hydrogen bonding (PEO and PLL) or electrostatic interactions (PLL). Competitive adsorption experiments from a mixture of PEO and PLL homopolymers evidenced greater interactions of PLL with silica while displacement experiments even revealed that free PLL chains could desorb PEO chains from the particle surface. This allowed us to better understand the adsorption mechanism of PEO-b-PLL copolymer at the silica surface. At low surface coverage, both blocks adsorbed in flat conformation leading to the flocculation of the particles as neither steric nor electrostatic forces could take place at the silica surface. The addition of a large excess of copolymer favoured the dispersion of flocs according to a presumed mechanism where PLL blocks of incoming copolymer chains preferentially adsorbed to the surface by displacing already adsorbed PEO blocks. The gradual addition of silica particles to an excess of PEO-b-PLL copolymer solution was the preferred method for particle coating as it favoured equilibrium conditions where the copolymer formed an anchor-buoy (PLL-PEO) structure with stabilizing properties at the silica-water interface.     

pH-responsive diblock copolymer micelles at the silica/aqueous solution interface: Adsorption kinetics and equilibrium studies

The adsorption behavior of two examples of a weakly basic diblock copolymer, poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (PDMA-PDEA), at the silica/aqueous solution interface has been investigated using a quartz crystal microbalance with dissipation monitoring and an optical reflectometer. Dynamic and static light scattering measurements have also been carried out to assess aqueous solution properties of such pH-responsive copolymers. In alkaline solution, core-shell micelles are formed above the critical micelle concentration (cmc) by both copolymers, whereas the chains are molecularly dissolved (as unimers) at all concentrations in acidic solution. As a result, the adsorption behavior of PDMA-PDEA diblock copolymers on silica is strongly dependent on both the copolymer concentration and the solution pH. Below the cmc at pH 9, the cationic PDMA-PDEA copolymers adsorb as unimers and the conformation of the adsorbed polymer is essentially flat. At concentrations just above the cmc, the initial adsorption of copolymer onto the silica is dominated by the unimers due to their faster diffusion compared to the much larger micelles. Rearrangement of the adsorbed unimers and/or their subsequent displacement by micelles from solution is then observed during an equilibration period, and the final adsorbed mass is greater than that observed below the cmc. At concentrations well above the cmc, the much higher proportion of micelles in solution facilitates more effective competition for the surface at all stages of the adsorption process and no replacement of initially adsorbed unimers by micelles is evident. However, the adsorbed layer undergoes gradual rearrangement after initial adsorption. This relaxation is believed to result from a combination of further copolymer adsorption and swelling of the adsorbed layer.     

Adsorption properties of poly(l-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) at a hydrophobic interface: influence of tribological stress, pH, salt concentration, and polymer molecular weight

The adsorption properties of a graft copolymer of poly(ethylene glycol) (PEG) with a polycationic backbone, namely, poly( l-lysine)- graft-poly(ethylene glycol) (PLL- g-PEG), onto nonpolar, hydrophobic PDMS surfaces from aqueous solution and the lubrication properties of the self-mated sliding contacts of PDMS surfaces modified with PLL- g-PEG have been investigated. Whereas PLL- g-PEG is spontaneously attracted to negatively charged surfaces as a result of the polycationic PLL backbone, the collective interaction of (CH 2) 4 hydrocarbon moieties on the lysine units in the PLL backbone with nonpolar, hydrophobic surfaces also enables the adsorption of PLL- g-PEG onto hydrophobic surfaces such as PDMS. The adsorption and lubrication properties of PLL- g-PEG have been investigated by varying the aqueous solution parameters, such as pH (2, 7, and 12) and KCl concentration (0, 0.01, 0.1, and 1 M) as well as the length of the PLL backbone of the copolymer (20 vs 375 kDa). In the absence of tribological stress, the adsorption of PLL- g-PEG onto PDMS surfaces was mainly governed by the KCl concentration, whereas the role of pH or the molecular weight of the copolymer was of relatively minor importance; for all pH values, the adsorbed mass decreased with increasing KCl concentration. Under tribological stress, however, a clear dependence of the lubrication properties of PLL- g-PEG on all of the studied parameters, including pH, KCl concentration, and backbone molecular weight, was observed. The adsorption strength of PLL- g-PEG on PDMS surfaces, rather than the adsorbed mass itself, appeared to be the most critical parameter in determining the lubrication properties.     

Synthesis, rapid responsive thickening, and self-assembly of brush copolymer poly(ethylene oxide)-graft-poly(N,N-dimethylaminoethyl methacrylate) in aqueous solutions

Double hydrophilic brush copolymer poly(ethylene oxide)-graft-poly(N,N-dimethylaminoethyl methacrylate) (PEO-g-PDMAEMA) was successfully prepared via atom transfer radical polymerization (ATRP). We investigated the pH/thermoresponsive behaviors of PEO-g-PDMAEMA brush-shaped copolymer concentrated aqueous solutions by rheology. The observed LCST strongly decreased with increasing pH of the solutions, which was lower than that of linear block copolymer for different pH, indicating rapid thermoresponsiveness of the brush PDMAEMA chains. An unexpected shear thickening behavior was observed and could be tuned by the pH, resulting from the mobile nature and tractive force of the densely grafted hydrophobic chains of PDMAEMA at high pH. Self-assembly of the brush copolymer in a different pH and ionic strength environment was studied by transmission electron microscopy. A wormlike cylinder structure was formed at low pH. Fractals were observed for the brush copolymer aqueous solution in the presence of NaCl. The results showed that by adjusting the pH and NaCl concentration of the dispersions fractal aggregates with different topology were obtained. The observations reported here can supply a better understanding of the molecular self-assembling nature and be used to develop responsive materials with better performance.     

Study of pH-sensitive copolymer/phospholipid complexes using the langmuir balance technique: effect of anchoring sequence and copolymer molecular weight

The behavior of three copolymers of N-isopropylacrylamide (NIPAM), methacrylic acid (MAA), and hydrophobic moiety was studied at phospholipid monolayer/subphase interfaces. The hydrophobic moieties, N-terminal dioctadecylamine (DODA) and random octadecylacrylate (ODA), were used as anchoring groups. The interactions between a 1,2-distearoyl-sn-glycero-3-phosphatidylcholine (DSPC) monolayer and the copolymers were studied using the Langmuir balance technique. The effect of subphase pH, distribution of anchors along the copolymer chain, and copolymer molecular weight on the nature of the interactions between the copolymer chains and the DSPC monolayer were investigated. A first-order kinetics model was used to analyze the copolymers adsorption at the DSPC monolayer/subphase interface and allowed the interaction area between the copolymer chains and the DSPC monolayer, A(x), to be determined. The interaction area appears to depend on the subphase pH and the copolymer molecular weight. On decreasing pH, the interaction area of high molecular weight copolymers increases significantly; this is consistent with the copolymer chain phase transition from an extended coil to a collapsed globule while pH is lowered. In the latter conformation, strong hydrophobic attractive interactions between the copolymer chains and the hydrophobic part of the DSPC monolayer favor the copolymer intercalation, which could eventually provoke the phospholipidic layer destabilization or rupture.     

Adsorption behavior of urokinase by polypropylene film modified with amino acids as affinity groups

In order to prepare a new-type adsorbent with an affinity ligand, polypropylene films modified with amino acid groups such as -phenylalanine (Phe), , -Phe, -cysteine (Cys), and , -tryptophane (Try), were prepared by radiation-induced grafting of glycidyl methacrylate (GMA) onto polypropylene (PP) films and subsequent amination of poly-GMA graft chains. The physical and chemical properties of the GMA-grafted PP film and the PP film modified with amino acid groups were investigated by IR and XPS. The adsorption of urokinase for the PP films modified with four kinds of amino acid groups were examined under various conditions, such as the contents of the amino acid group and pH value. The adsorption of urokinase increased with the increasing content of the amino acid group. The adsorption of the PP film modified with four kinds of amino acid groups was in the following order: -Phe> , -Phe> , -Try> -Cys. The adsorption amounts of urokinase by the PP film modified with four kinds of amino acid groups at pH 7.4 was higher than that at pH 9.0.     

pH-responsive copolymer films by surface-catalyzed growth

We have engineered a new class of pH-responsive polymer films on gold surfaces by first developing a controlled, surface-catalyzed polymerization to prepare a copolymer film consistent with poly(methylene-co-ethyl acetate) and subsequently hydrolyzing the ester side chains to varying extents to yield carboxylic acids (denoted as PM-CO2H). When pH is increased, the acid groups become deprotonated or charged, dramatically increasing their water solubility and greatly altering the film properties. The carboxylic acid content within the copolymer film can be adjusted by changing the monomer concentration ratio used in the polymerization process or the length of time for the hydrolysis. We have designed PM-CO2H films to consist predominately (>95%) of polymethylene (PM) so that the film is hydrophobic in the uncharged state and, thereby, exhibits an extremely large pH-induced response in barrier properties once ionized. The effect of polymer composition on pH response was investigated by electrochemical impedance spectroscopy (EIS), reflectance-absorption infrared spectroscopy (RAIRS), and contact angle measurements. At a 1%-4% molar acid content, the copolymer film exhibits a 5 orders of magnitude change in its resistance to ion transport over 2-3 pH units. The pH at which this response begins can be tailored from pH 5 to pH 10 by decreasing the acid content in the film from 4% to 1%.     

Control of the PEO chain conformation on nanoparticles by adsorption of PEO-block-poly(L-lysine) copolymers and its significance on colloidal stability and protein repellency

The physical adsorption of PEO(n)-b-PLL(m) copolymers onto silica nanoparticles and the related properties of poly(ethylene oxide) (PEO)-coated particles were studied as a function of the block copolymer composition. Copolymers adopt an anchor-buoy conformation at the particle surface owing to a preferential affinity of poly(L-lysine) (PLL) blocks with the silica surface over PEO blocks when a large excess of copolymer is used. The interdistance between PEO chains at particle surface is highly dependent on the size of PLL segments; a dense brush of PEO is obtained for short PLL blocks (DP = 10), whereas PEO chains adopt a so-called interacting "mushroom" conformation for large PLL blocks (DP = 270). The size of the PEO blocks does not really influence the copolymer surface density, but it has a strong effect on the PEO layer thickness as expected. Salt and protein stability studies led to similar conclusions about the effectiveness of a PEO layer with a dense brush conformation to prevent colloidal aggregation and protein adsorption. Besides, a minimal PEO length is required to get full stabilization properties; as a matter of fact, both PEO(45)-b-PLL(10) and PEO(113)-b-PLL(10) give rise to a PEO brush conformation but only the latter copolymer efficiently stabilizes the particles in the presence of salt or proteins.     

A Monte Carlo study of the effect of polymer rigidity on adsorption behaviour

The effect of copolymer sequence distribution and stiffness on the adsorption–desorption transition and configuration of an adsorbed polymer chain is examined by Monte Carlo methods. Trends in the adsorption–desorption transition temperatures show that the transition temperature of the block and alternating copolymers are determined by entropic factors while the copolymers with a random sequence distribution (block-ran, random, or alt-ran, defined below) are controlled by enthalpic considerations. Analysis of the conformation of adsorbed chains and monomer density profiles suggests that utilizing an adsorbed rigid copolymer may be useful at tuning the properties of an interface in a multiphase material. A block copolymer can be utilized to affect substantial surface coverage and extensive expansion away from the surface. Additionally, an increase in the rigidity of the diblock chain will improve the expansion of the chain in all three dimensions. Alternatively, random copolymer structures offer a chain that will adopt a flatter adsorbed configuration that offers more efficient surface coverage. In this case, the expansion of the copolymer along the surface can be enhanced by increasing the stiffness of the chain with little or no change in the expansion away from the interface.     

Cellulose Functionalization via ATRP Grafting of Glycidyl Methacrylate for Cr（VI） Adsorption

Cellulose was first grafted with glycidyl methacrylate （GMA） in an ionic liquid via atom transfer radical polymerization （ATRP） and then the introduced epoxy groups were reacted with ethanediamine （EDA） to obtain an amino adsorbent. The grafting copolymer and the obtained adsorbent were characterized by FTIR, aH NMR, TEM and SEM. The results showed that the grafted copolymers had grafted polymer chains with well-controlled molecu- lar weight and polydispersity, the polymerization was a controlled system. The cellulose adsorbent had numerous micropores on the surface and showed high performance for Cr（VI） adsorption. The adsorption behavior was pH dependent and the sorption equilibrium was achieved within 2 h on the adsorbent.     

大孔交联甲基丙烯酸缩水甘油酯共聚物的合成及其吸附性能研究(Ⅱ)对磷的吸附性能

前文[1]介绍了大孔交联甲基丙烯酸缩水甘油酯（GMA）与三烯丙基氰尿酸酯（TAC）共聚物（GT）的合成及其孔结构性能。本文研究了GT共聚物经与甘露醇进行功能基化反应制得新型吸磷吸附剂（GTG）。并观察了该吸附剂在诸因素（如pH值、温度及时间等）对磷的吸附性能。实验结果表明：该吸附剂在磷酸盐缓冲液中，pH＝7．0时，温度为37℃，磷的初始含量为10mg／dl时，吸附剂对磷的吸附量可达8．60mg／g吸附剂。     

Water-soluble hydrogen-bonding interpolymer complex formation between poly(ethylene glycol) and poly(acrylic acid) grafted with poly(2-acrylamido-2-methylpropanesulfonic acid)

Comb-type copolymers of poly(acrylic acid) grafted with poly(2-acrylamido-2-methylpropanesulfonic acid) (PAMPSA) side chains form with poly(ethylene glycol), at low pH, water-soluble hydrogen-bonding interpolymer complexes. Turbidimetry, viscometry, and dynamic light scattering measurements suggest that compact, negatively charged, colloidal nanoparticles are formed at pH<3.75. The influence of the structure of the graft copolymers and of the ionic strength of the solution on the size of these nanoparticles was investigated. It was found that their hydrodynamic radius decreases by increasing the molecular mass of the PAMPSA side chains of the graft copolymer and increases with increasing the ionic strength of the solution.     

Adsorption characteristics of zwitterionic diblock copolymers at the silica/aqueous solution interface

The adsorption of a zwitterionic diblock copolymer, poly(2-(diethylamino)ethyl methacrylate)-block-poly(methacrylic acid) (PDEA59-PMAA50), at the silica/aqueous solution interface has been characterised as a function of pH. In acidic solution, this copolymer forms core-shell micelles with the neutral PMAA chains being located in the hydrophobic cores and the protonated PDEA chains forming the cationic micelle coronas. In alkaline solution, the copolymer forms the analogous inverted micelles with anionic PMAA coronas and hydrophobic PDEA cores. The morphology of the adsorbed layer was observed in situ using soft-contact atomic force microscopy (AFM): this technique suggests the formation of a thin adsorbed layer at pH 4 due to the adsorption of individual copolymer chains (unimers) rather than micelle aggregates. This is supported by the remarkably low dissipation values and the relatively low degrees of hydration for the adsorbed layers, as estimated using a combination of quartz crystal microbalance with dissipation monitoring (QCM-D) and optical reflectometry (OR). In alkaline solution, analysis of the adsorption data suggests a conformation for the adsorbed copolymers where one block projects normal to the solid/liquid interface; this layer consists of a hydrophobic PDEA anchor block adsorbed on the silica surface and an anionic PMAA buoy block extending into the solution phase. Tapping mode AFM studies were also carried out on the silica surfaces after removal from the copolymer solutions and subsequent drying. Interestingly, in these cases micelle-like surface aggregates were observed from both acidic and alkaline solutions. The lateral dimension of the aggregates seen is consistent with the corresponding hydrodynamic diameter of the copolymer micelles in bulk solution. The combination of the in situ and ex situ AFM data provides evidence that, for this copolymer, micelle aggregates are only seen in the ex situ dry state as a result of the substrate withdrawal and drying process. It remains unclear whether these aggregates are caused by micelle deposition at the surface during the substrate withdrawal from the solution or as a result of unimer rearrangements at the drying front as the liquid recedes from the surface.     

Brush-like copolymer as a physically adsorbed coating for protein separation by capillary electrophoresis

A brush-like copolymer consisting of poly(ethylene glycol) methyl ether methacrylate and N,N-dimethylacrylamide (PEGMA-DMA) was synthesized and used as a novel static physically adsorbed coating for protein separation by capillary electrophoresis for the first time, in order to stabilize electroosmotic flow (EOF) and suppress adsorption of proteins onto the capillary wall. Very stable and low EOF was obtained in PEGMA-DMA-coated capillary at pH 2.2-7.8. The effects of molar ratio of PEGMA to DMA, copolymer molecular mass, and pH on the separation of basic proteins were discussed. A comparative study of bare capillary with PEGMA-DMA-coated capillary for protein separation was also performed. The basic proteins could be well separated in PEGMA-DMA-coated capillary over the investigated pH range of 2.8-6.8 with good repeatability and high separation efficiency because the copolymer coating combines good protein-resistant property of PEG side chains with excellent coating ability of PDMA-contained backbone. Finally, the coating was successfully applied to the fast separation of other protein samples, such as protein mixture and egg white, which reveals that it is a potential coating for further proteomics analysis.     

Adsorption mechanism of mixed cationic/anionic collectors in feldspar-quartz flotation system

The adsorption mechanism of mixed cationic alkyl diamine and anionic sulfonate/oleate collectors at acidic pH values was investigated on microcline and quartz minerals through Hallimond flotation, electrokinetic and diffuse reflectance FTIR studies. In the presence of anionic collectors, neither of the minerals responded to flotation but the diamine flotation of the minerals was observed to be pH and concentration dependent. The presence of sulfonate enhanced the diamine flotation of the minerals by its co-adsorption. The difference in surface charge between the minerals at pH 2 was found to be the basis for preferential feldspar flotation from quartz in mixed diamine/sulfonate collectors. The infrared spectra revealed no adsorption of sulfonate collector when used alone but displayed its co-adsorption as diamine-sulfonate complex when used with diamine. The presence of sulfonate increased the diamine adsorption due to a decrease in the electrostatic head-head repulsion between the adjacent surface ammonium ions and thereby increasing the lateral tail-tail hydrophobic bonds. The mole ratio of diamine/sulfonate was found to be an important factor in the orientation of alkyl chains and thus the flotation response of minerals. The increase in sulfonate concentration beyond diamine concentration leads to the formation of soluble 1:2 diamine-sulfonate complex or precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase.     

Spectroscopic investigation of the adsorption mechanisms of polyacrylamide polymers onto iron oxide particles

The mechanisms of high-molecular-weight polyacrylamide nonionic homopolymer and 25 mol% anionic acrylate-substituted copolymer adsorption onto iron oxide particles were investigated via DRIFT and UV-vis spectroscopies at three pH values (6, 8.5, and 11). While electrostatic interactions play an important role in charged polymer adsorption, this information is not spectroscopically available. At pH values above and below pH 8.5 (the isoelectric point for the anionic polymer), bidentate chelation and hydrogen bonding were the main adsorption mechanisms. At the isoelectric point, monodentate chelation was observed to be the main mode of adsorption, along with hydrogen bonding. For the nonionic polymer, in all cases, hydrogen bonding through the carbonyl group was the main mode of adsorption. The adsorption of both polymers conformed well to the Freundlich model, suggesting that the adsorbed polymer amount increases with increasing polymer concentration up to 7500 g/t solid, rather than approaching monolayer coverage. Spectroscopic evidence was found to suggest that hydrolysis of nonionic polyacrylamide occurs at high pH.     

Adsorption of Poly(ethylene oxide)-Poly(lactide) Copolymers. Effects of Composition and Degradation

The effect of chemical degradation of two diblock copolymers of poly(ethylene oxide) (E) and poly(lactide) (L), E(39)L(5) and E(39)L(20), on their adsorption at silica and methylated silica was investigated with in situ ellipsometry. Steric stablization of polystyrene dispersions was investigated in relation to degradation. Hydrolysis of the poly(lactide) block of the copolymers was followed at different temperatures and pH by using HPLC to measure the occurrence of lactic acid in solution. The block copolymers were quite stable in pH-unadjusted solution at low temperature, whereas degradation was facilitated by increasing temperature or lowering of the pH. Lower degradation rates of E(39)L(20) where observed at low temperature in comparison with those of E(39)L(5), whereas the degradation rates of the copolymers were quantitatively similar at high temperature. The adsorption of the copolymers at methylated silica substrates decreased with increasing degree of degradation due to the reduction in the ability of hydrophobic block to anchor the copolymer layer at the surface. At silica the adsorption initially increased with increasing degradation, particularly for E(39)L(20) due to deposition of aggregates onto the surface. After extensive degradation the adsorption of the copolymers at both silica and methylated silica resembled that of the corresponding poly(ethylene oxide) homopolymer. Overall, it was found that the eventual reduction in adsorption occurred at a lower degree of degradation for E(39)L(5) than for E(39)L(20). Mean-field calculations showed a reduced anchoring for the block copolymers with decreasing poly(lactide) block length at hydrophobic surfaces. In accordance with this finding, it was observed that polystyrene dispersions were stabilized by E(39)L(20) or E(39)L(5) in a way that depended on both the lactide block length and the degree of degradation. Upon degradation of the hydrophobic block, stabilization of the polystyrene dispersions was maintained initially, but eventually degradation resulted in destabilization. The average residual copolymer concentration required for stabilization of the polystyrene dispersions was much higher than the corresponding concentration of intact copolymer required for stabilization. Copyright 2001 Academic Press.     

CMC型高分子表面活性剂在固/液界面上的吸附

在润湿、乳化、洗涤、分散等应用领域中,表面活性剂分子在界面上的吸附状态对性能有重要影响.另一方面,在化学驱油过程中,表面活性剂分子在氧化物矿物上的吸附是引起表面活性剂损失的主要原因,表面活性剂的损耗量大,将降低采收率及经济效益[1].高分子表面活性剂作为一种多功能的新型表面活性剂在许多领域有广阔的应用前景,但对其性能研究尚处于起步阶段,特别是结构复杂的高分子双亲性共聚物,在吸附、乳化等方面研究尚少报导.羧甲基纤维素系列高分子表面活性剂是采用独特的超声波辐照技术合成的嵌段型共聚物,具有优良的表/界面活性[2],可望用…     

Alumina interaction with AMPS-MPEG random copolymers I. Adsorption and electrokinetic behavior

Adsorption of brush copolymers, bearing sulfonate groups and polyethylene glycol segments, on to alumina particles in suspension in water has been investigated. Study of the adsorption isotherms revealed that the copolymers displayed a strong affinity for the surface of the alumina regardless of the fraction of ionic groups on the polymer. For poly(ethylene glycol) content greater than 50%, the adsorption isotherms revealed an initial adsorption plateau followed by a second one. The shape of the adsorption isotherms was interpreted in terms of the polymer configuration at the solid-to-liquid interface. The effects of the pH and the ionic force on adsorption were studied and connected to the effects of interaction between chain segments at the surface of the alumina particles. Changes in the electrokinetic properties of the alumina particles after addition of the copolymers were investigated by following the zeta potential of particles as a function of pH. In the presence of the copolymer continuous shift of the isoelectric point IEP to a more acidic values was observed. Beyond a certain concentration the zeta potential remained negative regardless of the pH.