基于自发布里渊散射的双路分布式光纤传感器设计与实现

利用光纤中的布里渊散射光频移与温度和应变呈线性关系的原理,提出了一种基于自发布里渊散射的双支路分布式光纤传感系统。该系统利用不同种类光纤的布里渊频移差别,同时对两条线路的应力和温度进行监测,实现对被测对象多方位的同时测量,缩短了探测时间,提高了工作效率。本文实现了两路光纤的同时监测,用6 km的光纤作为传感介质,获得了4 m的空间分辨率。得到的实验结果表明,提出的系统能准确判断40 ns脉冲光在两路传感光纤沿线产生的自发布里渊背向散射光谱的中心频率变化。      

偏振态对分布式光纤泄漏检测系统的影响研究

研制了一种基于Sagnac干涉仪的直线型分布式光纤传感器,可实时进行管道泄漏检测与定位。分析和研究了该干涉仪的泄漏检测原理、泄漏源定位方法以及光偏振态对传感器性能的影响。当两束光偏振态相同时,系统具有最佳的性能;当两束光正交时,无法实现信号检测。管道泄漏的实验结果表明,该系统能较准确地确定泄漏源位置,且定位误差为0.69%。     

Optical fiber temperature sensor based on wavelength-dependent detection

Semiconductor fiber temperature sensors have been used widely in many fields, but most of them pick up temperature by measuring the optical intensity of certain fixed narrow-band in absorption spectrum.Furthermore, they are sensitive to the loss of optical intensity and the fluctuation of light source power.The novel temperature measurement system proposed in this paper is based on the semiconductor absorption theory and the spectral analysis of method. To measure temperature, the sensor model detects not the certain narrow-band spectrum but the most spectra of the optical absorption edge. Therefore the measurement accuracy and the stability can be improved greatly. Experimental results are in agreement with theoretical analysis results perfectly.     

High-repetition-rate distributed Brillouin sensor based on optical correlation-domain analysis with differential frequency modulation

A kind of high-repetition-rate distributed Brillouin sensor is proposed and experimentally demonstrated based on optical correlation-domain analysis with differential frequency modulation, where the optical frequencies of the pump and the probe waves are modulated at slightly different RFs so that the temporal position of the measurement is continuously and repeatedly swept along a fiber under test. A distribution map of Brillouin frequency variation along a 100 m optical fiber is acquired at a repetition rate of 20 Hz with an accuracy of ±2.5 MHz and a spatial resolution of about 80 cm.     

57-km single-ended spontaneous Brillouin-based distributed fiber temperature sensor using microwave coherent detection

We present a novel technique for performing single-ended distributed fiber temperature measurements by use of microwave heterodyne detection of spontaneous Brillouin scattering. Brillouin frequency-shift measurements were obtained for a sensing length of 57 km, with a spatial resolution of 20 m. The rms error in frequency measurements at the far end of the sensing fiber was less than 3 MHz, and the overall frequency dependence on temperature was 1.07+/-0.06 MHz/K.     

A nuclear-spin based rotation sensor using optical polarization and detection methods

We describe a rotation sensor that is based on the detection of the nuclear magnetic resonance signal of¹²⁹Xe in the gas phase. Under rotation shifts of the signal phase and Larmor frequency occur, which can be used to determine orientational angle variations with an accuracy of about 1^o and rotation rates of 0.4 mHz to 5 Hz with a precision of 0.4 mHz during the measurement time, which is of the order of 3×T ₂, the nuclear spin relaxation time. The nuclear spin species is polarized by spin-exchange collisions with optically pumped ground-state spins of Rb-gas atoms. The Rb atoms also present in the sample are used as a magnetometer to probe the free-induction decay of the nuclear spin ensemble. Polarization, detection, and data processing sheemes are described in detail and the current sensitivity and limitations of this Stuttgart nuclear magnetic resonance (NMR) gyroscope are discussed. Possibilities for further improvements are pointed out.     

Full distributed fiber optical sensor for intrusion detection in application to buried pipelines

Based on the microbend effect of optical fiber, a distributed sensor for real-time continuous monitoring of intrusion in application to buried pipelines is proposed. The sensing element is a long cable with a special structure made up of an elastic polymer wire, an optical fiber, and a metal wire. The damage point is located with an embedded optical time domain reflectometry (OTDR) instrument. The intrusion types can be indicated by the amplitude of output voltage. Experimental results show that the detection system can alarm adequately under abnormal load and can locate the intrusion point within 22.4 m for distance of 3.023 km.     

Effect of optical phase on a distributed Brillouin sensor at centimeter spatial resolution

Because of the power imbalance between the two arms of an interferometer in an electro-optic modulator (EOM), the output of the EOM is combined amplitude modulation (AM) and phase modulation (PM) for the probe signal consisting of the pulse and the dc component. Because of this PM, the Brillouin gain-loss spectrum becomes asymmetric. The central Brillouin frequency is shifted from that of an AM pulse. The maximum extinction ratio of the EOM is limited to approximately 29 dB for a power-splitting ratio of 51% to 49%. The asymmetric property induced by PM is not pulse shape dependent; for both Gaussian- and super-Gaussian-shaped pulses the Brillouin loss spectrum is symmetric for AM and asymmetric for combined AM and PM (power imbalance).     

Optical fiber curvature sensor based on few mode fiber

An optical fiber curvature sensor based on interference between LP₀₁–LP₀₂ modes of a circularly symmetric few mode fiber (FMF) is presented. The device consists of two single-mode fiber and a 10-cm FMF. The two single-mode fiber is offset-spliced to each end of the FMF. When the optical fiber is kept straight and fixed, the interference pattern appears in the transmitted spectrum. As the fiber device is bent, the visibility of the interference fringes (at 1530 nm) decreases, reaching values close to 0.3. The dynamic range of the device can be tailored by the proper selection of the length of FMF. The relationship between the fringe visibility and the curvature is linear while the curvature is between 11 m⁻¹ and 16 m⁻¹. The result indicates that the compact sensor can be used in the measurement of large curvature, which is also important in structural health monitoring.     

Effect of Brillouin slow light on distributed Brillouin fiber sensors

The effect of Brillouin slow light on distributed Brillouin fiber sensors (DBFSs) is studied. We demonstrate Brillouin slow light for a 1.2 ns pulse with peak powers (PS) from 3.3 to 56.2 mW on depletion of the pump power (PP) ranging from 1.3 to 83.2 mW in conventional optical fibers (SMF-28). Experiments show that, when pump power depletion is not negligible, for a given PP the Brillouin gain and delay time of a pulse decrease when PS increases in a long (> or =10 km) sensing fiber. The optimum pump beam depletion resulting from strong interaction of the pump and the probe in the fiber provides accurate temperature and strain information at a high spatial resolution. Our study reveals that at low PP the spatial resolution error caused by the pulse delay for a DBFS with centimeter spatial resolution is less than 5% of the pulse length.     

Fiber-optic distributed measurement of polarization beat length using slope-assisted Brillouin optical correlation-domain reflectometry

Optical Review - We demonstrate distributed measurement of the polarization beat length along single-mode optical fibers (SMFs) using slope-assisted Brillouin optical correlation-domain...     

Accuracy enhancement in Brillouin scattering distributed temperature sensor based on Hilbert transform

The scattering optical signal of OTDR based Brillouin scattering distributed sensor is very weak and have a frequency width of several decades megahertz, so it is hard to perform the traditional analogue coherent demodulation. A novel optical coherent detection based on Hilbert transform is presented here. In detail, Brillouin backscattering light is coherent detected with the reference light, which is modulated by microwave electric optical modulator to produce frequency-adjustable light, then the detected photocurrent signal is demodulated by digital signal processing based on Hilbert transform, and at last the distributed sensing signal with better S/N ratio is gained, which can enhance the performance of the sensor. The simulation and experimental results of the detection method are given.     

基于单模光纤的分布式温度传感器研制

在对光纤背向喇曼散射温度效应理论分析的基础上,研制了基于单模光纤的5km分布式温度传感器。实验比较了温度传感解调方法,选择反斯托克斯(Anti-Stokes)和斯托克斯(Stokes)背向喇曼散射光强度比值进行解调。介绍了系统的硬件组成和软件实现。实验表明,系统能精确地进行分布式测温,温度分辨率为1℃,空间分辨率为2m。     

Digital coherent detection research on Brillouin optical time domain reflectometry with simplex pulse codes

The X-ray spectrometer used in high-energy-density plasma experiments generally requires both broad X-ray energy coverage and high temporal, spatial, and spectral resolutions for overcoming the difficulties imposed by the X-ray back- ground, debris, and mechanical shocks. By using an elliptical crystal together with a streak camera, we resolve this issue at the SG-II laser facility. The carefully designed elliptical crystal has a broad spectral coverage with high resolution, strong rejection of the diffuse and/or fluorescent background radiation, and negligible source broadening for extended sources. The spectra that are Bragg reflected （23° 〈 θ 〈 38°） from the crystal are focused onto a streak camera slit 18 mm long and about 80 μm wide, to obtain a time-resolved spectrum. With experimental measurements, we demonstrate that the quartz（1011） elliptical analyzer at the SG-II laser facility has a single-shot spectral range of （4.64-6.45） keV, a typical spectral resolution of E/△E = 560, and an enhanced focusing power in the spectral dimension. For titanium （Ti） data, the lines of interest show a distribution as a function of time and the temporal variations of the He-α and Li-like Ti satellite lines and their spatial profiles show intensity peak red shifts. The spectrometer sensitivity is illustrated with a temporal resolution of better than 25 ps, which satisfies the near-term requirements of high-energy-density physics experiments.     

基于马赫-曾德尔干涉仪的光纤扭转传感器

提出一种基于马赫-曾德尔干涉仪的扭转传感器,通过实验进行了验证。干涉仪采用无芯光纤-七芯光纤-无芯光纤的结构,当七芯光纤发生扭转时,中心纤芯和外部纤芯的相位差发生变化,使得其透射光谱随之改变。实验结果表明,随着七芯光纤扭转角度的增加,输出光谱的下陷峰向短波长方向偏移,其传感敏感度为0.33nm/(°),角度最小测量精度为0.15°。所提光纤传感器具有成本低、构造简单、制作简便的优点,可以应用于涉及扭转、旋转等的角度测量领域。     

Optical fiber humidity sensor based on evanescent-wave scattering

The phenomenon of evanescent-wave scattering (EWS) is used to design an optical-fiber humidity sensor. Porous solgel silica (PSGS) coated on the surface of a silica optical-fiber core scatters evanescent waves that penetrate the coating layer. Water molecules in the gas phase surrounding the optical fiber can be absorbed into the inner surface of the pores of the porous silica. The absorbed water molecules form a thin layer of liquid water on the inner surface of the porous silica and enhance the EWS. The amount of water absorbed into the PSGS coating is in dynamic equilibrium with the water-vapor pressure in the gas phase. Therefore the humidity in the air can be quantitatively determined with fiber-optic EWS caused by the PSGS coating. The humidity sensor reported here is fast in response, reversible, and has a wide dynamic range. The possible interference caused by EWS to an optical-fiber gas sensor with a reagent-doped PSGS coating as a transducer is also discussed.     

利用受激布里渊散射在光纤中实现光存储

利用有限差分法在慢变包络近似下求解了耦合波方程组,并从理论上实现了短光脉冲的存储。研究了数据脉冲的读出效率随声子寿命、布里渊增益系数、数据脉冲强度和控制脉冲强度的变化规律。结果显示:在长声子寿命的条件下,可以获得高的读出效率和长的存储时间,而布里渊增益系数和数据脉冲强度对读出效率没有影响;增大布里渊增益系数可以降低所需控制脉冲的强度。这种方法对短脉冲可以实现有效存储,而对长脉冲不能实现存储。     

Optical single sideband-frequency generation with carrier totally suppressed for Brillouin distributed fiber sensing

The power fluctuation and multi-sidebands of the RF modulated electro-optic intensity modulator (EOIM) can lead to a degraded resolution of the Brillouin distributed sensors. A standard commercial fiber-pigtailed DFB-LD is locked to one of the sidebands of the EOIM. Optical single sideband-frequency generation is realized with the carrier and the other sidebands totally suppressed. The locked LD greatly improves the power stability of the injected sideband. No dc bias controlling to the EOIM is needed in the locking process. This simple method provides large tuning range (～1 GHz), fast response (～100 μs), and high side-frequency suppression ratio (～60 dB). Thus, it is practical for high-resolution Brillouin sensing systems as well as microwave photonics.     

利用受激布里渊散射在光纤中实现光存储

利用有限差分法在慢变包络近似下求解了耦合波方程组,并从理论上实现了短光脉冲的存储。研究了数据脉冲的读出效率随声子寿命、布里渊增益系数、数据脉冲强度和控制脉冲强度的变化规律。结果显示：在长声子寿命的条件下,可以获得高的读出效率和长的存储时间,而布里渊增益系数和数据脉冲强度对读出效率没有影响;增大布里渊增益系数可以降低所需控制脉冲的强度。这种方法对短脉冲可以实现有效存储,而对长脉冲不能实现存储。     

Stimulated Brillouin scattering frequency-domain analysis in a single-mode optical fiber for distributed sensing

A numerical and experimental analysis of the stimulated Brillouin scattering in a single-mode optical fiber for distributed sensing applications is carried out in the frequency domain. The theoretical model describing the Brillouin interaction is solved by taking into account the temporal dynamics of the acoustic wave that is involved. The simulations and the experimental results reveal the role played by the ac component of the acoustic wave, which is responsible for significant changes of the small-signal stimulated Brillouin scattering transfer function that occur when the modulation frequency rises above the natural Brillouin gain spectrum linewidth. One should take these effects into account to perform accurate signal processing of frequency-domain signals in high-resolution distributed sensing applications.