Bias sensitive spectral sensitivity in double -SiC:H pin structures

In this work we discuss the use of multilayer stacked structures (p(SiC:H)/i(SiC:H)/n(SiC:H)/p(SiC:H)/i(Si:H)/n(Si:H)) sandwiched between two transparent conductive contacts as colour sensing devices. The thickness and the absorption coefficient of both front and back p–i–n cells were specifically designed in order to achieve simultaneously high blue collection and red transmittance in the front cell and full green absorption and high red collection in the back cell. Electric and optical sensing methods were used for measuring the current–voltage characteristics and the spectral sensitivity, under different experimental conditions. Results show that the spectral sensitivity of the device is strongly modulated by the applied voltage, which allows colour selectivity. The results were supported by a physical model.     

Microcrystalline silicon‐carbon alloys as anti‐reflection window layers in high efficiency thin film silicon solar cells

Microcrystalline silicon‐carbide (μc‐SiC:H) films were prepared using hot wire chemical vapor deposition at low substrate temperature. The μc‐SiC:H films were employed as window layers in microcrystalline silicon (μc‐Si:H) solar cells. The short‐circuit current density (J_SC) in these n‐side illuminated n–i–p cells increases with increasing the deposition time t_W of the μc‐SiC:H window layer from 5 min to 60 min. The enhanced J_SC is attributed to both the high transparency and an anti‐reflection effect of the μc‐SiC:H window layer. Using these favourable optical properties of the μc‐SiC:H window layer in μc‐Si:H solar cells, a J_SC value of 23.8 mA/cm² and cell efficiencies above 8.0% were achieved with an absorber layer thickness of 1 μm and a Ag back reflector. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Light trapping for a‐Si:H/µc‐Si:H tandem solar cells using direct pulsed laser interference texturing

We present a‐Si:H/µc‐Si:H tandem solar cells on laser textured ZnO:Al front contact layers. Direct pulsed laser interference patterning (DLIP) was used for writing arrays of one‐dimensional micro gratings of submicron period into ZnO:Al films. The laser texture provides good light trapping which is indicated by an increase in short‐circuit current density of 20% of the bottom cell limited device compared to cells on planar ZnO:Al. The open‐circuit voltage of the cells on laser textured ZnO:Al is almost the same as for cells on planar substrates, indicating excellent growth conditions for amorphous and microcrystalline silicon on the U‐shaped grating grooves. DLIP is a simple, single step and industrially applicable method for large area periodic texturing of ZnO:Al thin films. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

The p recombination layer in tunnel junctions for micromorph tandem solar cells

A new tunnel recombination junction is fabricated for n–i–p type micromorph tandem solar cells. We insert a thin heavily doped hydrogenated amorphous silicon (a-Si:H) p + recombination layer between the n a-Si:H and the p hydrogenated nanocrystalline silicon (nc-Si:H) layers to improve the performance of the n–i–p tandem solar cells. The effects of the boron doping gas ratio and the deposition time of the p-a-Si:H recombination layer on the tunnel recombination junctions have been investigated. The current-voltage characteristic of the tunnel recombination junction shows a nearly ohmic characteristic, and the resistance of the tunnel recombination junction can be as low as 1.5 ·cm 2 by using the optimized p-a-Si:H recombination layer. We obtain tandem solar cells with open circuit voltage V oc = 1.4 V, which is nearly the sum of the V oc s of the two corresponding single cells, indicating no V oc losses at the tunnel recombination junction.     

硅锗量子阱结构在硅异质结太阳电池中应用的数值模拟

利用半导体工艺和器件仿真软件silvaco TCAD(Technology Computer Aided Design),模拟研究了采用硅/硅锗合金(silicon/silicon germanium alloy,Si/Si_(1-x)Ge_x)量子阱结构作为吸收层的薄膜晶体硅异质结太阳电池各项性能.模拟结果显示,长波波段光学吸收随锗含量的增加而增加,而开路电压则因Si_(1-x)Ge_x)层带隙的降低而下降.锗含量为0.25时,短路电流密度的增加补偿了开路电压的衰减,效率提升0.2%.氢化非晶硅/晶体硅(a-Si:H/c-Si)界面空穴密度以及Si_(1-x)Ge_x)量子阱的体空穴载流子浓度制约着空穴费米能级的位置,进而影响到开路电压的大小.随着锗含量增加,a-Si:H/c-Si界面缺陷对开压的影响降低,Si_(1-x)Ge_x)量子阱的体缺陷对开压的影响则相应增加.高效率含Si_(1-x)Ge_x)量子阱结构的硅异质结太阳电池的制备需要a-Si:H/c-Si界面缺陷的良好钝化以及高质量Si_(1-x)Ge_x)量子阱的生长.     

CuO薄膜的制备及其光伏特性

通过反应磁控溅射在n型硅和玻璃衬底上制备了p型CuO薄膜.使用X射线衍射仪和紫外-可见光-近红外光度计研究了p型CuO薄膜的结构和光学特性,得出其平均晶粒尺寸和光学带隙分别为8nm和1.36eV.通过研究其电压-电流关系确定了在p型CuO薄膜和n型硅衬底之间形成了p-n结.在AM 1.5光照条件下p-CuO/n-Si电池的开路电压为0.33V,短路电流密度为6.27mA/cm2,填充因数和能量转化效率分别为0.2和0.41%.     

高温退火处理下SiNx薄膜组成及键合结构变化

采用等离子增强化学气相沉积法, 以氨气和硅烷为反应气体, p型单晶硅为衬底, 低温下(200 ℃)制备了非化学计量比氮化硅(SiN_x)薄膜. 在N₂氛围中, 于500–1100 ℃范围内对薄膜进行热退火处理. 室温下分别使用Fourier变换红外吸收(FTIR)光谱技术和X射线光电子能谱(XPS)技术测量未退火以及退火处理后SiN_x薄膜的Si–N, Si–H, N–H键键合结构和Si 2p, N 1s电子结合能以及薄膜内N和Si原子含量比值R的变化. 详细讨论了不同温度退火处理下SiN_x薄膜的FTIR和XPS光谱演化同薄膜内Si, N, H原子间键合方式变化之间的关系. 通过分析FTIR和XPS光谱发现退火温度低于800 ℃时, SiN_x薄膜内Si–H和N–H键断裂后主要形成Si–N键; 当退火温度高于800 ℃时薄膜内Si–H和N–H键断裂利于N元素逸出和Si纳米粒子的形成; 当退火温度达到1100 ℃时N₂与SiN_x薄膜产生化学反应导致薄膜内N和Si原子含量比值R增加. 这些结果有助于控制高温下SiN_x薄膜可能产生的化学反应和优化SiN_x薄膜内的Si纳米粒子制备参数. 关键词： x薄膜')" href="#">SiN_x薄膜 Fourier变换红外吸收光谱 X射线光电子能谱 键合结构     

Excellent passivation of thin silicon wafers by HF‐free hydrogen plasma etching using an industrial ICPECVD tool

In this work, hydrogen plasma etching of surface oxides was successfully accomplished on thin (～100 µm) planar n‐type Czochralski silicon wafers prior to intrinsic hydrogenated amorphous silicon [a‐Si:H(i)] deposition for heterojunction solar cells, using an industrial inductively coupled plasma‐enhanced chemical vapour deposition (ICPECVD) platform. The plasma etching process is intended as a dry alternative to the conventional wet‐chemical hydrofluoric acid (HF) dip for solar cell processing. After symmetrical deposition of an a‐Si:H(i) passivation layer, high effective carrier lifetimes of up to 3.7 ms are obtained, which are equivalent to effective surface recombination velocities of 1.3 cm s^–1 and an implied open‐circuit voltage (V_oc) of 741 mV. The passivation quality is excellent and comparable to other high quality a‐Si:H(i) passivation. High‐resolution transmission electron microscopy shows evidence of plasma‐silicon interactions and a sub‐nanometre interfacial layer. Using electron energy‐loss spectroscopy, this layer is further investigated and confirmed to be hydrogenated suboxide layers. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

γ射线辐照对a-SiC:H薄膜结构与特性的影响

 采用射频（13.56 MHz）反应溅射方法制备a-SiC:H 薄膜，并将其在空气中进行高能γ射线(平均为1.25 MeV)辐照，5个样品的吸收剂量分别为0，2×10⁴，4×10⁴，6×10⁴，8×10⁴ Gy。采用拉曼及红外光谱对薄膜的结构进行表征,得到了其结构与特性的变化规律。研究与分析表明：随样品吸收剂量的增加，陷入空穴中的电子会被激发，a-SiC:H薄膜中的SiC成份增加，电阻率变小，数量级为105Ω·cm；薄膜存在结晶化的趋势,其主要原因在于由Si－O－Si键断裂而产生的Si取代膜中C－C键中的C而形成晶态SiC，在此过程中出现了Si－O－Si键及a-SiC:H的减少，晶态SiC的增加。经γ射线辐照后薄膜的氢含量降低，折射率从5.19增大到5.53，辐照后薄膜的透过率均低于原膜的透过率。在500~2 300 cm^-1(对应波长为20.00~5.29 μm)波段内，a-SiC:H薄膜存在一定的增透作用。     

SiC埋层的制备及其红外吸收特性

采用metal vapor vacuum arc离子源的离子束合成方法，对单晶Si衬底注入C^＋离子，获得不同剂量下的SiC埋层．C^＋离子束的引出电压为50kV，注入的剂量为3.0×10¹⁷—1.6×10¹⁸cm^-2．通过红外吸收谱的测试和分析，表明SiC埋层的结晶程度依赖于剂量的大小．研究证实，可以在较低的平均衬底温度下（低于400℃）得到含立方相结构的SiC埋层． 关键词：     

A new proposal for Si tandem solar cell: Significant efficiency enhancement in 3C–SiC/Si

In order to considerable enhancement of the efficiency of silicon solar cells, in this paper, for the first time, we present a new proposal for silicon based tandem solar cells. For investigation of this idea, we have evaluated the characteristics of 3C–SiC/Si crystalline tandem solar cells connected series by a tunneling junction, under air mass 1.5 global irradiance spectrums. A 2D simulation including the effects of surface passivation, back surface field (BSF), and carrier tunneling have been performed to obtain the optical and electrical characteristics of single junction silicon, 3C–SiC, and finally the tandem cells. The obtained data illustrate that the best design parameters considering the experimental limitations can be obtained. High energy conversion efficiency for the proposed structure of 26.09% has been achieved for 3C–SiC/Si tandem structure driven by 20.49% and 17.86% conversion efficiencies of single junction Si and 3C–SiC solar cells, respectively. Our results justifies that the higher conversion efficiency of the Si-based tandem structure compared with 3C–SiC and Si cells stems from enhancement of open circuit voltage and fill factor parameter at the hands of decrease in short circuit current limited by the top 3C–SiC cell.     

Theoretical investigation on the passivation layer with linearly graded bandgap for the amorphous/crystalline silicon heterojunction solar cell

Passivation layer with linearly graded bandgap (LGB) was proposed to improve the performance of amorphous/crystalline silicon heterojunction (SHJ) solar cell by eliminating the large abrupt energy band uncontinuity at the a‐Si:H/c‐Si interface. Theoretical investigation on the a‐Si:H(p)/the LGB passivation layer(i)/c‐Si(n)/a‐Si:H(i)/a‐Si:H(n⁺) solar cell via AFORS‐HET simulation show that such LGB passivation layer could improve the solar cell efficiency (η) by enhancing the fill factor (FF) greatly, especially when the a‐Si:H(p) emitter was not efficiently doped and the passivation layer was relatively thick. But gap defects in the LGB passivation layer could make the improvement discounted due to the open‐circuit voltage (V_OC) decrease induced by recombination. To overcome this, it was quite effective to keep the gap defects away from the middle of the bandgap by widening the minimum bandgap of the LGB passivation layer to be a little larger than that of the c‐Si base. The underlying mechanisms were analysed in detail. How to achieve the LGB passivation layer experimentally was also discussed. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

射频溅射法制备3C-SiC和4H-SiC薄膜

利用射频溅射法在Si衬底上制备了SiC薄膜，并利用x射线衍射（XRD）和红外（IR）吸收谱对薄膜的结构、成分及化学键合状态进行了分析.XRD结果表明，低温制备的SiC薄膜为非晶相，而在高温下（＞800℃），薄膜呈现4HSiC和3CSiC结晶相.IR谱显示，溅射制备薄膜的吸收特性主要为Si—C键的吸收.此外，还利用原子力显微镜对薄膜的表面形貌进行了研究，并研究了样品的场发射特性. 关键词： 射频溅射 SiC薄膜 结构 表面形貌 场发射     

Si—OH基团对SiCOH低k薄膜性能的影响与控制

研究了十甲基环五硅氧烷(D5)的电子回旋共振等离子体沉积的SiCOH薄膜中Si—OH基团对介电性能和漏电流的影响.结果表明Si—OH含量的增大会导致介电常数k的增大、漏电流的降低和介电色散的增强.由于Si—OH结构的强极化补偿了薄膜密度减小带来的介电常数降低，导致总的介电常数k增大.高Si—OH含量下漏电流的降低是由于封端的Si—OH基团降低了薄膜中Si—O网络的连通概率p而导致网络电导下降的缘故.介电色散的增强与Si—OH封端结构的快极化过程有关.改变放电参数以提高电子能量，从而提高源的电离程度，使更多的Si—OH基团断裂并通过缩合反应形成Si—O—Si网络，可以进一步降低薄膜的介电常数. 关键词： SiCOH薄膜 Si—OH结构 介电性能 ECR放电等离子体     

Kr离子注入SiC的拉曼光谱研究

应用拉曼光谱研究了5 MeV Kr离子（注量分别为5×1013,2×1014,1×1015 ions/cm2）室温注入6H SiC单晶及其高温退火处理后结构的变化。 研究表明, 注入样品的拉曼光谱中不仅出现了Si—C振动的散射峰, 还产生了同核Si—Si键和C—C键散射峰。 Si—C散射峰强度随退火温度升高而增强, 当退火温度高达1000 ℃时, 已接近未辐照SiC的散射峰强度。晶体Si—Si键散射峰强度随退火温度变化不大, 而非晶Si—Si键散射峰强度随退火温度的增加逐渐消失。相对拉曼强度（Relative Raman Intensity, 简称RRI）随注量的增加逐渐减小并趋于饱和, 且不同退火温度样品的饱和注量不相同; RRI随退火温度的增加逐渐升高, 这在低注量样品中表现得尤为明显。 低、中、高3种注量样品的RRI随退火温度的增加从重合逐渐分离, 并且退火温度越高, 分离越大。 Raman spectroscopy was used to study the structure changes of 6H SiC single crystal implanted with 5 MeV Kr (Krypton) at room temperature and subsequently annealed at high temperature. The Raman spectrum of the implanted SiC displays not only Si—C bonds vibration peaks, but also homonuclear Si—Si and C—C bond vibration peaks. Si—C bond vibration peaks gradually strengthen with increasing temperature. When annealing at 1000 ℃, the peak intensity of Raman spectrum is close to that of virgin specimen. It is found that crystal Si—Si bond vibration peaks do not change when annealing, but amorphous Si—Si bond vibration peaks disappear with increasing annealing temperature. The Relative Raman Intensity (RRI) values decrease with increasing fluence and tend to saturate, but the saturation fluences is different for various anneal temperature. The RRI values increases with raising annealing temperature, which is more obvious in low implanted specimens. At the same time, the RRI values separate gradually with increasing temperature and this phenomenon is strengthened by annealing temperature.     

Control of epitaxial growth at a-Si:H/c-Si heterointerface by the working pressure in PECVD

The epitaxial-Si(epi-Si) growth on the crystalline Si(c-Si) wafer could be tailored by the working pressure in plasmaenhanced chemical vapor deposition(PECVD).It has been systematically confirmed that the epitaxial growth at the hydrogenated amorphous silicon(a-Si:H)/c-Si interface is suppressed at high pressure(hp) and occurs at low pressure(1p).The hp a-Si:H,as a purely amorphous layer,is incorporated in the 1p-epi-Si/c-Si interface.We find that:(i) the epitaxial growth can also occur at a-Si:H coated c-Si wafer as long as this amorphous layer is thin enough;(ii) with the increase of the inserted hp layer thickness,lp epi-Si at the interface is suppressed,and the fraction of a-Si:H in the thin films increases and that of c-Si decreases,corresponding to the increasing minority carrier lifetime of the sample.Not only the epitaxial results,but also the quality of the thin films at hp also surpasses that at lp,leading to the longer minority carrier lifetime of the hp sample than the lp one although they have the same amorphous phase.     

Effects of sic buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates

ZnO films have been grown by a sol-gel process on Si (1 1 1) substrates with and without SiC buffer layers. The influence of SiC buffer layer on the optical properties of ZnO films grown on Si (1 1 1) substrates was investigated. The intensity of the E₂ (high) phonon peak in the micro-Raman spectrum of ZnO film with the SiC buffer layer is stronger than that of the sample without the SiC buffer layer, and the breadth of E₂ (high) phonon peak of ZnO film with the SiC buffer layer is narrower than that of the sample without the SiC buffer layer. These results indicated that the crystalline quality of the sample with the SiC buffer layer is better than that of the sample without the SiC buffer layer. In photoluminescence spectra, the intensity of free exciton emission from ZnO films with the SiC buffer was much stronger than that from ZnO film without the SiC buffer layer, while the intensity of deep level emission from sample with the SiC buffer layer was about half of that of sample without the SiC buffer layer. The results indicate the SiC buffer layer improves optical qualities of ZnO films on Si (1 1 1) substrates.     

Synthesis of epitaxial silicon carbide films through the substitution of atoms in the silicon crystal lattice: A review

A review of recent advances in the field of epitaxial growth of SiC films on Si by means of a new method of epitaxial substitution of film atoms for substrate atoms has been presented. The basic statements of the theory of the new method used for synthesizing SiC on Si have been considered and extensive experimental data have been reported. The elastic energy relaxation mechanism implemented during the growth of epitaxial SiC films on Si by means of the new method of substitution of atoms has been described. This method consists in substituting a part of carbon atoms for silicon matrix atoms with the formation of silicon carbide molecules. It has been found experimentally that the substitution for matrix atoms occurs gradually without destroying the crystalline structure of the matrix. The orientation of the film is determined by the “old” crystalline structure of the initial silicon matrix rather than by the silicon substrate surface only, as is the case where conventional methods are used for growing the films. The new growth method has been compared with the classical mechanisms of thin film growth. The structure and composition of the grown SiC layers have been described in detail. A new mechanism of first-order phase transformations in solids with a chemical reaction through an intermediate state promoting the formation of a new-phase nuclei has been discussed. The mechanism providing the occurrence of a wide class of heterogeneous chemical reactions between the gas phase and a solid has been elucidated using the example of the chemical interaction of the CO gas with the single-crystal Si matrix. It has been shown that this mechanism makes it possible to grow a new type of templates, i.e., substrates with buffer transition layers for growing wide-band-gap semiconductor films on silicon. A number of heteroepitaxial films of wide-band-gap semiconductors, such as SiC, AlN, GaN, and AlGaN on silicon, whose quality is sufficient for the fabrication of a wide class of micro- and optoelectronic devices, have been grown on the SiC/Si substrate grown by solid-phase epitaxy.     

SiC film growth on Si(111) by supersonic beams of C 60

The development of electronic devices based on Silicon Carbide (SiC) has been strongly limited by the difficulties in growing high quality crystalline bulk materials and films. We have recently elaborated a new technique for the synthesis of SiC on clean Si substrates by means of supersonic beams of C₆₀: the electronic and structural properties of the film can be controlled by monitoring the beam parameters, i.e. flux and particles energy and aggregation state. SiC films were grown in Ultra High Vacuum on Si(111)-7×7, at substrates temperatures of 800 ^° C, using two different supersonic beams of C₆₀: He and H₂ have been used as seeding gases, leading to particles energy of 5 eV and 20 eV, respectively. Surface characterisation was done in situ by Auger and X-Ray photoelectron spectroscopy, as well as by low energy electron diffraction and ex situ by atomic force microscopy technique. SiC films exhibited good structural and electronic properties, with presence of defects different from the typical triangular voids. Received 20 November 2001     

Effect of buffer layers on performance of organic photovoltaic devices based on copper phthalocyanine-perylene dye heterojunction

The work presents the results of research on the systems formed from thin films of copper phthalocyanine (CuPc), N-N′-dimethylperylene-3,4,9,10-dicarboximide (MePTCDI), electrodes of ITO and Ag, and from buffer layers: MoO₃ at ITO and BCP at Ag. We have observed the effect of each buffer layer on voltage dependence of dark current and photocurrent, and on open circuit voltage-light intensity relationship. The system with both buffer layers exhibited the highest values of open circuit voltage and fill factor. The buffer layers improve transport of charge carriers within near-electrode regions, reduce dissociation of excitons on electrodes and reveal processes of charge carrier generation and recombination within the CuPc/MePTCDI junction.