AlGaN/GaN MIS-HEMT using NbAlO dielectric layer grown by atomic layer deposition

We present an AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor (MIS-HEMT) with an NbAlO high-k dielectric deposited by atomic layer deposition (ALD).Surface morphology of samples are observed by atomic force microscopy (AFM),indicating that the ALD NbAlO has an excellent-property surface.Moreover,the sharp transition from depletion to accumulation in capacitance-voltage (C-V)curse of MIS-HEMT demonstrates the high quality bulk and interface properties of NbAlO on AlGaN.The fabricated MIS-HEMT with a gate length of 0.5 μm exhibits a maximum drain current of 960 mA/mm,and the reverse gate leakage current is almost 3 orders of magnitude lower than that of reference HEMT.Based on the improved direct-current operation,the NbAlO can be considered to be a potential gate oxide comparable to other dielectric insulators.     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga 关键词： AlGaN/GaN HEMT 电流崩塌 坑状缺陷 位错缺陷     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下，研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明，钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降；在高漏偏压下，场板的尺寸对器件抑制崩塌的能力有较大影响，而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现，场板结构不仅能够抑制虚栅的充电过程，而且提供了放电途径，有利于虚栅的放电，从而抑制电流崩塌.在此基础上，通过建立场板介质对虚栅放电的模型，解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因.     

场板结构AlGaN/GaN HEMT的电流崩塌机理

在不同的漏偏压下,研究了钝化和不同场板尺寸AlGaN/GaN HEMT对电流崩塌的抑制能力.实验结果表明,钝化器件对电流崩塌的抑制能力随着漏偏压的升高而显著下降;在高漏偏压下,场板的尺寸对器件抑制崩塌的能力有较大影响,而合适尺寸的场板结构在各个漏偏压下都能够很好的抑制电流崩塌.深入分析发现,场板结构不仅能够抑制虚栅的充电过程,而且提供了放电途径,有利于虚栅的放电,从而抑制电流崩塌.在此基础上,通过建立场板介质对虚栅放电的模型,解释了高漏偏压下场板的尺寸对器件抑制崩塌的能力有较大影响的原因. 关键词： AlGaN/GaN HEMT 场板 电流崩塌     

A study on Al2O3 passivation in GaN MOS-HEMT by pulsed stress

This paper studies systematically the drain current collapse in AlGaN/GaN metal-oxide-semiconductor high electron mobility transistors （MOS-HEMTs） by applying pulsed stress to the device. Low-temperature layer of Al2O3 ultrathin film used as both gate dielectric and surface passivation layer was deposited by atomic layer deposition （ALD）. For HEMT, gate turn-on pulses induced large current collapse. However, for MOS-HEMT, no significant current collapse was found in the gate turn-on pulsing mode with different pulse widths, indicating the good passivation effect of ALD Al2O3. A small increase in Id in the drain pulsing mode is due to the relieving of self-heating effect. The comparison of synchronously dynamic pulsed Id - Vds characteristics of HEMT and MOS-HEMT further demonstrated the good passivation effect of ALD Al2O3.     

基于脉冲方法的超短栅长GaN基高电子迁移率晶体管陷阱效应机理

陷阱效应导致的电流崩塌是制约GaN基微波功率电子器件性能提高的一个重要因素,研究深能级陷阱行为对材料生长和器件开发具有非常重要的意义.随着器件频率的提升,器件尺寸不断缩小,对小尺寸器件中深能级陷阱的表征变得越发困难.本文制备了超短栅长（L_g=80 nm）的AlGaN/GaN金属氧化物半导体高电子迁移率晶体管（MOSHEMT）,并基于脉冲I-V测试和二维数值瞬态仿真对器件的动态特性进行了深入研究,分析了深能级陷阱对AlGaN/GaN MOSHEMT器件动态特性的影响以及相关陷阱效应的内在物理机制.结果表明,AlGaN/GaN MOSHEMT器件的电流崩塌随着栅极静态偏置电压的增加呈非单调变化趋势,这是由栅漏电注入和热电子注入两种陷阱机制共同作用的结果.根据研究结果推断,可通过改善栅介质的质量以减小栅漏电或提高外延材料质量以减少缺陷密度等措施达到抑制陷阱效应的目的,从而进一步抑制电流崩塌.     

A physics-based potential and electric field model of a nanoscale rectangular high-K gate dielectric HEMT

In this paper, we have developed a physics-based model for surface potential, channel potential, electric field and drain current for AlGaN/GaN high electron mobility transistor with high-K gate dielectric using two-dimensional Poisson equation under full depletion approximation with the inclusion of effect of polarization charges. The accuracy of the model has been verified and is found to be in good agreement with the simulated results.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

高场应力及栅应力下AlGaN/GaN HEMT器件退化研究

采用不同的高场应力和栅应力对AlGaN/GaN HEMT器件进行直流应力测试,实验发现：应力后器件主要参数如饱和漏电流,跨导峰值和阈值电压等均发生了明显退化,而且这些退化还是可以完全恢复的;高场应力下,器件特性的退化随高场应力偏置电压的增加和应力时间的累积而增大;对于不同的栅应力,相对来说,脉冲栅应力和开态栅应力下器件特性的退化比关态栅应力下的退化大.对不同应力前后器件饱和漏电流,跨导峰值和阈值电压的分析表明,AlGaN势垒层陷阱俘获沟道热电子以及栅极电子在栅漏间电场的作用下填充虚栅中的表面态是这些不同应 关键词： AlGaN/GaN HEMT器件 表面态(虚栅) 势垒层陷阱 应力     

AlGaN/GaN高电子迁移率晶体管肖特基高温退火机理研究

在不同应力条件下,研究了AlGaN/GaN高电子迁移率晶体管高温退火前后的电流崩塌、栅泄漏电流以及击穿电压的变化.结果表明,AlGaN/GaN高电子迁移率晶体管通过肖特基高温退火以后,器件的特性得到很大的改善.利用电镜扫描(SEM)和X射线光电子能谱(XPS)对高温退火前、后的肖特基接触界面进行深入分析,发现器件经过高温退火后,Ni和AlGaN层之间介质的去除,并且AlGaN材料表面附近的陷阱减少,使得肖特基有效势垒提高,从而提高器件的电学特性. 关键词： AlGaN/GaN高电子迁移率晶体管 肖特基接触 界面陷阱     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

Sodium beta-alumina thin films as gate dielectrics for A1GaN/GaN metal-insulator-semiconductor high-electron-mobility transistors

<正>Sodium beta-alumina（SBA） is deposited on AlGaN/GaN by using a co-deposition process with sodium and Al₂O₃ as the precursors.The X-ray diffraction（XRD） spectrum reveals that the deposited thin film is amorphous.The binding energy and composition of the deposited thin film,obtained from the X-ray photoelectron spectroscopy（XPS） measurement,are consistent with those of SBA.The dielectric constant of the SBA thin film is about 50.Each of the capacitance-voltage characteristics obtained at five different frequencies shows a high-quality interface between SBA and AlGaN.The interface trap density of metal-insulator-semiconductor high-electron-mobility transistor（MISHEMT） is measured to be（3.5～9.5）×10¹⁰ cm^-2·eV^-1 by the conductance method.The fixed charge density of SBA dielectric is on the order of 2.7×10¹² cm^-2.Compared with the AlGaN/GaN metal-semiconductor heterostructure high-electronmobility transistor（MESHEMT）,the AlGaN/GaN MISHEMT usually has a threshold voltage that shifts negatively. However,the threshold voltage of the AlGaN/GaN MISHEMT using SBA as the gate dielectric shifts positively from—5.5 V to—3.5 V.From XPS results,the surface valence-band maximum（VBM-E_F） of AlGaN is found to decrease from 2.56 eV to 2.25 eV after the SBA thin film deposition.The possible reasons why the threshold voltage of AlGaN/GaN MISHEMT with the SBA gate dielectric shifts positively are the influence of SBA on surface valence-band maximum （VBM-E_F）,the reduction of interface traps and the effects of sodium ions,and/or the fixed charges in SBA on the two-dimensional electron gas（2DEG）.     

Breakdown voltage analysis of Al0.25Ga0.75N/GaN high electron mobility transistors with partial silicon doping in the AlGaN layer

In this paper,two-dimensional electron gas（2DEG） regions in AlGaN/GaN high electron mobility transistors（HEMTs） are realized by doping partial silicon into the AlGaN layer for the first time.A new electric field peak is introduced along the interface between the AlGaN and GaN buffer by the electric field modulation effect due to partial silicon positive charge.The high electric field near the gate for the complete silicon doping structure is effectively decreased,which makes the surface electric field uniform.The high electric field peak near the drain results from the potential difference between the surface and the depletion regions.Simulated breakdown curves that are the same as the test results are obtained for the first time by introducing an acceptor-like trap into the N-type GaN buffer.The proposed structure with partial silicon doping is better than the structure with complete silicon doping and conventional structures with the electric field plate near the drain.The breakdown voltage is improved from 296 V for the conventional structure to 400 V for the proposed one resulting from the uniform surface electric field.     

Breakdown voltage analysis of Al_0.25Ga_0.75N/GaN high electron mobility transistors with partial silicon doping in the AlGaN layer

In this paper,two-dimensional electron gas(2DEG) regions in AlGaN/GaN high electron mobility transistors(HEMTs) are realized by doping partial silicon into the AlGaN layer for the first time.A new electric field peak is introduced along the interface between the AlGaN and GaN buffer by the electric field modulation effect due to partial silicon positive charge.The high electric field near the gate for the complete silicon doping structure is effectively decreased,which makes the surface electric field uniform.The high electric field peak near the drain results from the potential difference between the surface and the depletion regions.Simulated breakdown curves that are the same as the test results are obtained for the first time by introducing an acceptor-like trap into the N-type GaN buffer.The proposed structure with partial silicon doping is better than the structure with complete silicon doping and conventional structures with the electric field plate near the drain.The breakdown voltage is improved from 296 V for the conventional structure to 400 V for the proposed one resulting from the uniform surface electric field.     

Influence of Schottky drain contacts on the strained AlGaN barrier layer of AlGaN/AlN/GaN heterostructure field-effect transistors

Rectangular Schottky drain AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) with different gate contact areas and conventional AlGaN/AlN/GaN HFETs as control were both fabricated with same size. It was found there is a significant difference between Schottky drain AlGaN/AlN/GaN HFETs and the control group both in drain series resistance and in two-dimensional electron gas (2DEG) electron mobility in the gate-drain channel. We attribute this to the different influence of Ohmic drain contacts and Schottky drain contacts on the strained AlGaN barrier layer. For conventional AlGaN/AlN/GaN HFETs, annealing drain Ohmic contacts gives rise to a strain variation in the AlGaN barrier layer between the gate contacts and the drain contacts, and results in strong polarization Coulomb field scattering in this region. In Schottky drain AlGaN/AlN/GaN HFETs, the strain in the AlGaN barrier layer is distributed more regularly.     

AlGaN/GaN高电子迁移率晶体管中kink效应的半经验模型

初步分析了AlGaN/GaN 器件上的kink效应. 在直流模型的基础上, 建立了AlGaN/GaN 高电子迁移率晶体管中kink效应的半经验模型, 并加入了kink效应发生的漏源偏压与栅源偏压的关系. 该模型得出较为准确的模拟结果, 可用来判断kink效应的发生和电流的变化量. 最后, 我们采用模型仿真结合实验分析的方法, 对kink效应进行了一定的物理研究, 结果表明碰撞电离对kink效应的发生有一定的促进作用.     

The degradation and recovery properties of AlGaN/GaN high-electron mobility transistors under direct current reverse step voltage stress

Direct current(DC) reverse step voltage stress is applied on the gate of an AlGaN/GaN high-electron mobility transistor(HEMT).Experiments show that parameters degenerate under stress.Large-signal parasitic source/drain resistance(RS/RD) and gate-source forward I-V characteristics are recoverable after breakdown of the device under test(DUT).Electrons trapped by both the AlGaN barrier trap and the surface state under stress lead to this phenomenon,and surface state recovery is the major reason for the recovery of device parameters.     

A study of GaN MOSFETs with atomic-layer-deposited Al2O3 as the gate dielectric

Accumulation-type GaN metal-oxide-semiconductor field-effect transistors (MOSFETs) with atomic-layer-deposited Al₂O₃ gate dielectrics are fabricated. The device, with atomic-layer-deposited Al₂O₃ as the gate dielectric, presents a drain current of 260 mA/mm and a broad maximum transconductance of 34 mS/mm, which are better than those reported previously with Al₂O₃ as the gate dielectric. Furthermore, the device shows negligible current collapse in a wide range of bias voltages, owing to the effective passivation of the GaN surface by the Al₂O₃ film. The gate drain breakdown voltage is found to be about 59.5 V, and in addition the channel mobility of the n-GaN layer is about 380 cm²/Vs, which is consistent with the Hall result, and it is not degraded by atomic-layer-deposition Al₂O₃ growth and device fabrication.