反相离子对高效液相色谱法分离测定钪、锡和铝

 以 1,2 二苯乙烯 4,4′ 双 (1 偶氮 ) 3,4 二羟基苯 2 ,2′ 二磺酸铵 (芪唑 )为柱前衍生试剂 ,采用反相离子对高效液相色谱法分离和测定钪、锡和铝。在C18柱上 ,用含 2 0mmol/LHAc NaAc缓冲溶液 (pH 6 0 )和 10mmol/L十二烷基磺酸钠的甲醇水溶液作流动相 ,检测波长 5 0 0nm ,同时分离测定了钪、锡和铝的络合物。钪、锡和铝的检出限分别为 0 9μg/L ,1 0 μg/L和 1 2 μg/L ,此方法用于矿石样品分析获得满意结果。     

A flow cell optosensor for lead based on immobilized gallocynin in chitosan membrane

Gallocynin immobilized in chitosan membrane has been studied as a sensor element of an optical sensor for lead using a flowing system. By using this set up, lead in solution has been determined in the concentration range from 1.0x10(-1) to 1.0x10(3) ppm with a detection limit of 0.075 ppm. The standard deviation of the method for the repeatability of lead detection at a concentration of 100 ppm was found to be 2.10%. The response of the sensor was reproducible and can be regenerated by using acidified saturated KNO(3) solution. Interference from foreign ions was also studied at 1:1 mole ratio of Pb(II):foreign ions.     

Determination of acetaldehyde in fuel ethanol by high-performance liquid chromatography with electrochemical detection.

The cyclic voltammetric behavior of acetaldehyde and the derivatized product with 2,4-dinitrophenylhydrazine (DNPHi) has been studied at a glassy carbon electrode. This study was used to optimize the best experimental conditions for its determination by high-performance liquid chromatographic (HPLC) separation coupled with electrochemical detection. The acetaldehyde-2,4-dinitrophenylhydrazone (ADNPH) was eluted and separated by a reversed-phase column, C18, under isocratic conditions with the mobile phase containing a binary mixture of methanol/LiCl(aq) at a concentration of 1.0 x 10(-3) M (80:20 v/v) and a flow rate of 1.0 mL min(-1). The optimum condition for the electrochemical detection of ADNPH was +1.0 V vs. Ag/AgCl as a reference electrode. The proposed method was simple, rapid (analysis time 7 min) and sensitive (detection limit 3.80 microg L(-1)) at a signal-to-noise ratio of 3:1. It was also highly selective and reproducible [standard deviation 8.2% +/- 0.36 (n = 5)]. The analytical curve of ADNPH was linear over the range of 3-300 mg L(-1) per injection (20 microL), and the analytical recovery was > 99%.     

流动注射双安培法测定盐酸苯肼

使用经过恒电位预阳极化处理的双铂电极,在外加电压差为0.20 V时,通过偶合盐酸苯肼在一支电极上的氧化和氧化铂在另一支电极上的还原两个不可逆电极过程,建立快速准确分析测定盐酸苯肼的流动注射双安培检测法.结果表明:在pH为2.36的B-R缓冲溶液中,外加电位差为0.20 V时测得盐酸苯肼的氧化电流与其浓度在1.0×10~(-6)～1.0×10~(-4)mol/L范围内呈线性关系(r=0.9949,n=9),检出限为1.0×10~(-7)mol/L.对1.0×10~(-5)mol/L的盐酸苯肼溶液的连续23次测定,电流值的相对标准偏差为2.26%.常见离子均不干扰测定.样品处理方法简单,且有较高的选择性和灵敏性,结果令人满意.     

纳米氧化铁修饰玻碳电极检测痕量镉离子

制备了一种纳米氧化铁修饰玻碳电极,并研究了镉离子在该修饰电极上的溶出伏安行为。结果表明,纳米氧化铁颗粒能有效促进镉离子的溶出伏安响应。在pH 6.0的磷酸缓冲溶液中,镉离子能有效吸附在纳米氧化铁表面并在-1.0 V时被还原。被还原的镉在正向扫描过程中可以重新氧化,并在-0.85 V处出现一明显的溶出伏安氧化峰。该峰电流随镉离子浓度的增大而增大,可用于对镉离子的检测。在最佳检测条件(pH 6.0,富集时间350 s,富集电位-1.0 V)下,镉离子的响应电流与其浓度在6.0×10-10～1.0×10-8mol/L以及1.0×10-8～1.0×10-5 mol/L范围内呈良好线性,检出限(S/N=3)为1.0×10-10 mol/L。干扰实验结果表明,一些常见的阳离子以及阴离子对镉离子的检测无明显干扰。将该方法用于实际样品的检测,回收率良好。     

ZnO/石墨烯修饰电极的制备及电化学性能研究

采用水热法合成了纳米氧化锌-氧化石墨烯复合材料,并基于该复合材料构制了一种新型双酚A传感器,研究了该传感器的电化学行为。结果表明,在含8.0×10-5mol/L CTAB的p H 7.0磷酸盐缓冲液中,双酚A在0.573V处出现1个不可逆的氧化峰,具有良好的电化学响应;其氧化峰电流与浓度在1.0×10-8~4.0×10-5mol/L范围内呈良好的线性关系,检出限为5.0×10-9mol/L;对模拟环境水样中双酚A进行3次平行测定的回收率在96.3%~101.9%之间,相对误差在1.2%~3.8%范围内。该传感器具有灵敏度高、线性范围宽的特点。     

反相离子对色谱法测定硫代硫酸根和碘离子的研究

首次利用Ｓ２Ｏ２－３和Ｉ－与Ｈｇ－ＥＤＴＡ二元络合物通过柱前衍生形成ＥＤＴＡ－Ｈｇ－Ｓ２Ｏ３和ＥＤＴＡ－Ｈｇ－Ｉ两种三元络合物的方法,实现了对Ｓ２Ｏ２－３和Ｉ－的间接反相离子对色谱分离和紫外检测。在ＺｏｒｂａｘＯＤＳ柱上,用甲醇∶水＝２３∶７７作流动相,内含对离子ＴＢＡ＋３．０ｍｍｏｌ／Ｌ,ＥＤＴＡ１．０ｍｍｏｌ／Ｌ,ＮａＮＯ３２．０ｍｍｏｌ／Ｌ和缓冲剂ＫＨ２ＰＯ４－Ｎａ２ＨＰＯ４（ｐＨ７．０）,紫外２５４ｎｍ检测。Ｓ２Ｏ２－３和Ｉ－的最小检出限分别为６１．１ｎｇ和３７．６ｎｇ。方法简便,选择性好。     

聚氯乙烯膜修饰碳微电极的研制及应用

采用浸涂流延法制得ＰＶＣ膜修饰碳微电极,用Ｋ３Ｆｅ（ＣＮ）６的循环伏安图考察了电极的电化学性能,并用此电极建立了环境水样中痕量汞的阳极溶出伏安法测定。在０．０６ｍｏｌ／Ｌ ＫＳＣＮ＋０．０１ｍｏｌ／ＬＫＣｌ介质中,富集电位－０．８０Ｖ,搅拌富集时间３００ｓ,扫描电压范围－０．２０～０．４０Ｖ,扫描速率３１４ｍＶ／ｓ,咄峰电流与Ｈｇ＾２＋浓度在０．０１～２．０ｍｇ／Ｌ的范围内有良好的线性关系,本电极     

Application of the spectral correction method and "neural networks" for simultaneous determination of V(V) and Al(III)

Simultaneous determination of V(V) and Al(III) was performed by application of neural networks when the calibration matrix was performed using β-correction spectra. Two reactions between V(V) and Al(III) and Alizarin Red S (ARS) as a ligand have been investigated and applied for the simultaneous spectrophotometric determination of these metal ions. The parameters controlling behavior of the system were investigated and optimum conditions selected. Feed-forward neural networks have been trained to quantify considered metal ions in mixtures under optimum conditions. Sigmoidal functions were used in the hidden and output layers. Determinations were made over the concentration range 0.10-7.80 μg ml⁻¹ of V(V) and 0.11-4.20 μg ml⁻¹ of Al(III). Applying this method satisfactorily to simultaneous determination of these metal ions in several synthetic solutions with total relative standard error less than 4.02% validated the proposed method.     

A PVC plasticized sensor for Ni(II) ion based on a simple ethylenediamine derivative.

A new PVC membrane ion selective electrode which is highly selective towards Ni(II) ions was constructed using a Schiff base containing a binaphthyl moiety as the ionophore. The sensor exhibited a good Nernstian response for nickel ions over the concentration range 1.0x10(-1)-5.0x10(-6) M with a lower limit of detection of 1.3x10(-6) M. It has a fast response time and can be used for a period of 4 months with a good reproducibility. The sensor is suitable for use in aqueous solutions in a wide pH range of 3.6-7.4 and works satisfactorily in the presence of 25% (v/v) methanol or ethanol. The sensor shows high selectivity to nickel ions over a wide variety of cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for the direct determination of nickel content in real samples: effluent samples, chocolates and hydrogenated oils.     

4-(5-溴-2-噻唑偶氮)间苯二酚反相阳离子对HPLC测定痕量铌、钒、铑、铬

本文报道新试剂4-(5-溴-2-噻唑偶氮)间苯二酚(5-Br-TAR)为柱前衍生试剂,以阳离子表面活性剂作为对离子试剂,用含15 mmol／L的pH 5.8的乙酸-乙酸钠缓冲溶液、0.05 mmol／L溴化钠、10 mmol／L TBA·Br的乙腈-甲醇-水(42 : 13：45,V／V／V)三元体系为流动相,在C8柱上25min内HPLC测定了Nb(V)、V(V)、Rh(Ⅲ)和Cr(Ⅵ)的5-BR-TAR螯合物。当SNR=2时,检出限分别为Nb(V)1.0、V(V)1.6、Rh(Ⅲ)0.9和Cr(Ⅵ)1.9μg／L。该方法用于测定污水中的铬和钒,结果良好。     

单扫示波极谱法测定食品包装材料中双酚A的研究

研究发现，在0.12mol/L Na2HPO4-KH2PO4(pH7.5)底液中，双酚A于峰电位（Ep)-1.0V(vs.SCE)处产生灵敏的极谱还原波，该波的二阶导数峰电流（ip)与双酚A浓度在2.0-10.0mg/L范围内呈良好的线性关系，检出限为1.0mg/L，萃取后测定，检出限为0.1mg/L。本法操作简便、快速、准确。用于食品包装材料中双酚A含量的测定，结果令人满意。     

Ion-selective electrode for aluminum determination in pharmaceutical substances, tea leaves and water samples

A novel ion-selective PVC membrane sensor for Al(III) ions based on 6-(4-nitrophenyl)-2-phenyl-4-(thiophen-2-yl)-3,5-diaza-bicyclo[3.1.0]hex-2-ene (NTDH) as a new ionophore has been prepared and studied. The electrode exhibit a good response for aluminum ion over concentration range of 1.0x10(-6) to 1.0x10(-1) mol L(-1) with a Nernstian slope of 19.6+/-0.4 mV per decade and low detection limit of 6.3x10(-7) mol L(-1). The best performance was obtained with membrane composition 30% poly(vinyl chloride), 62% acetophenone, 5% oleic acid, 3% ionophore and 2 ml tetrahydrofuran. NTDH-based electrode was suitable for aqueous solutions of pH 3. It has relatively fast response time (approximately 10 s) and can be used at least for 3 months without any considerable divergence in potentials. The proposed membrane electrode revealed good selectivity for Al(III) ions over a wide variety of other cations. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. The formation constant and stoichiometry ratio of ionophore-Al(III) complex were calculated at 25 degrees C by using segmented sandwich membrane method. It was used in non-aqueous solvents and also as indicator electrode in potentiometric determination of Al(III) ions in some real samples.     

基于核酸酶的新型阻抗传感器检测纺织品中的铅

建立一种基于核酸酶的电化学阻抗传感器检测纺织品中铅含量的方法。采用金纳米粒子修饰的金电极作为基底电极,以一种新型的核酸酶17EDNAzyme体系作为铅离子的生物识别元件,构建了一种新型的电化学阻抗传感器用于高灵敏选择性检测铅离子。在最佳实验条件下,传感器对溶液中铅离子的线性检测范围为1.0μg/L~10mg/L,检出限为0.6μg/L。测定结果的相对标准偏差小于5.4%(n=6),加标回收率在93.5%~106.0%之间。采用该法对实际纺织品样品进行测试,并与国标方法测定值进行对比,实验结果表明两种方法的测定值无显著性差异。该方法操作简便,对铅离子的检测具有良好的选择性,可用于现场样品的在线、快速测定。     

Novel membrane potentiometric sulfate ion sensor based on zinc-phthalocyanine for the quick determination of trace amounts of sulfate.

Poly(vinyl chloride) (PVC) based membranes of zinc-phthalocyanine (ZPC) with hexadecyltrimethylammonium bromide (HTAB) as a cation excluder, and dibutyl phthalate (DBP) and benzyl acetate (BA) as plasticizing solvent mediators were prepared and investigated as a SO4(2-) selective electrode. The best performance was observed with a membrane having a composition of ZPC-PVC-HTAB-BA in a ratio of 5%:32%:3%:60%, which works well over a wide concentration range (1.0 x 10(-2) - 1.0 x 10(-6) M) with a Nemstian slope of -29.2 mV per decade of activity, between the pH values of 2.0 to 7.0. This sensor shows a very fast response time of 10 s, and can be used over a period of 2 months with good reproducibility. The proposed sensor displays excellent selectivity for SO4(2-) over a large number of common inorganic anions. The sensor has been successfully applied for the direct and indirect determination of sulfate and zinc in zinc sulfate tablets, respectively. It was also used as an indicator electrode in the potentiometric titration of sulfate ions with barium ions.     

Electrodeposition and stripping voltammetry of arsenic(III) and arsenic(V) on a carbon black–polyethylene composite electrode in the presence of iron ions

In this work, a new sensor is proposed for the stripping voltammetric determination (anodic stripping voltammetry—ASV) of total arsenic(V) or arsenic(III). The sensor is based on an Fe-modified carbon composite electrode containing 30 % carbon black–high-pressure polyethylene (CB/PE). The modification with iron is achieved by the addition of Fe(III) or Fe(II) ions to the sample solution and co-electrodeposition of iron and arsenic on the CB/PE electrode. In anodic stripping voltammetry, two peaks are observed: an Fe peak at ?0.45 or ?0.29 V and a peak at 0.12?±?0.07 V which depends on the arsenic concentration and corresponds to the As(0) → As(III) oxidation, as is the case with other solid electrodes. The optimum conditions proposed for ASV determination of As(V) and As(III) in solutions in the presence of dissolved oxygen are the following: the background electrolyte is 0.005 M HCl containing 0.5–1 mg/?L Fe(III) for As(V) and containing 1.0–1.5 mg/?L Fe(III) for As(III), respectively; E _dep?=??2.3 V; rest period at ?0.10 V for 3–5 s before the potential sweep from ?0.2 to +0.4 V; scan rate is 120 mV/?s. The detection limit (LOD, t?=?120 s) for As(III) and As(V) is 0.16 and 0.8 μg/?L, respectively. Various hypotheses on the effect of Fe ions and atoms on the electrodeposition and dissolution of arsenic are considered. The new method of determination of As(III) and As(V) differs from known analogues by its simplicity, low cost, and easy accessibility of the electrode material. It allows the voltammetric determination of total arsenic after chemical reduction of all its forms to As(III) or after their oxidation to As(V).     

Determination of fluoride ions in urinary stones by ion chromatography

A method of the ion chromatographic determination of fluoride ions in urinary stones has been developed. Sample preparation of solid mineral-organic samples includes dissolution in concentrated hydrochloric acid, dilution with deionized water, and the elimination of excess calcium and magnesium cations by adding a KU-2 sulfo cation exchanger in the H-form to samples and filtration through a membrane filter. Anions were separated on a Shim-pack IC-AIS anion-exchange column (100 × 4.6 mm) with elution with a mixture of 2.0 mM phthalic acid and 1.2 mM sodium hydroxide (pH 3.5). The linearity range of the fluoride ions in the obtained solutions of urinary stones with conductometric detection was 0.01–300 mg/L, the limit of detection calculated by the 3s-test was 0.004 mg/L. The quantitative determination of fluoride ions in 20 samples of urinary stones was performed; in 80% of cases the presence of fluorides in the stones at a level from 0.01 to 4 mg/g of the stone was detected. The average concentration of the fluoride ions was 0.3 mg/g of stone. For 20% of the samples an elevated concentration of fluoride ions compared to the average one was found.     

反相高效液相色谱法测定肾复康胶囊中的野黄芩苷和芦丁

建立了肾复康胶囊中野黄芩苷和芦丁的反相高效液相色谱测定方法。以甲醇-水为提取溶剂,采用超声提取法对样品进行前处理。以0.02 mol/L磷酸二氢钾缓冲溶液(含1.0％（体积分数）冰醋酸)-甲醇（体积比为63∶37）为流动相,于330 nm波长下检测,肾复康提取液中野黄芩苷和芦丁可达基线分离,分析时间在20 min内。野黄芩苷和芦丁在10 ~300 mg/L内,其峰面积与浓度之间线性关系良好,目标物的加标回收率大于98％。该方法适用于肾复康胶囊及相关药材中野黄芩苷和芦丁黄酮类化合物的测定和质量控制。     

高效液相色谱法测定人血清中鬼臼乙叉甙浓度

建立了测定血清中鬼臼乙叉甙浓度的反相高效液相色谱方法。血清样品以乙酸乙酯提取,加表鬼臼毒噻吩糖甙作内标,以甲醇∶水（５５∶４５）为流动相,紫外２５４ｎｍ检测,最低检测浓度０．１ｍｇ／Ｌ,在药物浓度为０．５～５０ｍｇ／Ｌ范围内有良好的线性关系,Ｙ＝０．０１６０＋０．０３４０Ｘ,ｒ＝０．９９９１,回收率达９５．０％。日内、日间精密度分别为４．１６％和４．７６％（ｎ＝５）。用所建立的方法测定了患者的血清浓度,结果表明,方法简便、灵敏。     

流动注射化学发光法测定呋塞米

在酸性条件下呋塞米对Ce(Ⅳ)-Na_2SO_3弱化学发光体系具有很强的增敏作用,据此建立了流动注射化学发光法测定呋塞米的新方法.该法测定呋塞米的线性范围为0.01～1.0 mg/L,检出限为4×10~(-3)mg/L(3σ),RSD为2.2%(n=11,ρ=0.2mg/L),回收率为95%～105%.该法已应用于片剂和针剂中呋塞米含量的测定.