基于少模光纤的模分复用系统多输入多输出均衡与解调

针对光纤模分复用传输系统中模式耦合串扰问题, 设计并制备了一种新型少模光纤, 其较高的模式差分群延时保证各模式信道独立传输.在此基础上, 提出一种级联多输入多输出(MIMO)延时均衡算法, 进一步减少源于模式复用器和解复用器的模式串扰, 提高基于少模光纤的模分复用传输系统的传输距离和传输容量.与传统MIMO均衡算法相比, 级联MIMO延时均衡算法在没有显著增加计算复杂度的条件下, 能够应用于模式差分群延时很大的模分复用传输系统.对单信道传输速率为 40 Gbps的四相相移键控两模复用传输系统进行仿真, 经40 km少模光纤传输后, 采用级联MIMO均衡算法较普通MIMO均衡算法有1.7 dB的质量因子的提升. 仿真结果证明, 使用少模光纤和级联MIMO延时均衡算法能够有效地消除模分复用信号间的串扰, 有望在下一代大容量光纤传输系统中获得 推广应用. 关键词： 模分复用 少模光纤 模式差分群延时 多输入多输出均衡     

Fiber-modes and fiber-anisotropy characterization using low-coherence interferometry

An optical low-coherence interferometry technique has been used to simultaneously resolve the mode profile and to measure the intermodal dispersion of guided modes of a few-mode fiber. Measurements are performed using short samples of fiber (about 50 cm). There is no need for a complex mode-conversion technique to reach a high interference visibility. Four LP mode groups of the few-mode fiber are resolved. Experimental results and numerical simulations show that the ellipticity of the fiber core leads to a distinct splitting of the degenerate high-order modes in group index. For the first time, to the best of our knowledge, it has been demonstrated that degenerate LP11 modes are much more sensitive to core shape variations than the fundamental modes and that intermodal dispersion of high-order degenerate modes can be used for characterizing the anisotropy of an optical waveguide.     

应用耦合模理论研究光在圆对称双包层光纤中的传输(英文)

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

应用耦合模理论研究光在圆对称双包层光纤中的传输

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

Mode division multiplexing: from photonic integration to optical fiber transmission [Invited]

To overcome the capacity crunch of optical communications based on the traditional single-mode fiber(SMF), different modes in a few-mode fiber(FMF) can be employed for mode division multiplexing(MDM). MDM can also be extended to photonic integration for obtaining improved density and efficiency, as well as interconnection capacity. Therefore, MDM becomes the most promising method for maintaining the trend of "Moore's law" in photonic integration and optical fiber transmission. In this tutorial, we provide a review of MDM works and cutting-edge progresses from photonic integration to optical fiber transmission, including our recent works of MDM low-noise amplification, FMF fiber design, MDM Si photonic devices, and so on. Research and application challenges of MDM for optical communications regarding long-haul transmission and short reach interconnection are discussed as well. The content is expected to be of important value for both academic researchers and industrial engineers during the development of next-generation optical communication systems,from photonic chips to fiber links.     

Fiber acousto-optic mode coupling between the higher-order modes with adjacent azimuthal numbers

It is pointed out theoretically that fiber acousto-optic mode coupling can occur between the higher-order modes with adjacent azimuthal numbers. Selective fiber mode conversion from LP01 to LP11, and then to LP21 or LP02 is demonstrated experimentally in a few-mode fiber by using a method of cascaded acousto-optic mode coupling.     

A cost effective 100 Gbps hybrid MDM–OCDMA–FSO transmission system under atmospheric turbulences

FSO or free space optics is a familiar name used in a wide array of applications in the area of telecommunications. Due to its features of low maintenance cost and deployment time, most of the applications consider FSO as the alternative solution for appropriately replacing fiber optics. In this work, we have designed 100 Gbps FSO system by combining mode division multiplexing (MDM) and optical code multiple access scheme (OCDMA). Ten channels, each carrying 10 Gbps data, are transported over 8 km FSO link by using MDM of two Laguerre Gaussian modes and random diagonal codes. Moreover, the performance of proposed MDM–OCDMA–FSO system is also investigated under atmospheric turbulences.     

单模光纤波导模的傍轴传输特性

将LP01模表示成用拉盖尔-高斯模线性叠加的形式,利用柯林斯公式推导出单模光纤波导模通过傍轴ABCD光学系统的解析传输公式。用所得的解析公式对LP01模在自由空间的传输和聚焦特性作了研究,并和高斯基模进行了比较。数值计算结果表明,用高斯基模描述LP01模会产生一定误差。LP01模经过透镜聚焦后存在焦移,且焦移随着菲涅尔数传输特性的减小而增大。选择合适的菲涅尔数聚焦后,LP01模会出现长焦深,这是与聚焦的高斯模所不同的。     

Intermodal interference of LP01 and LP11 modes inpanda fibers

LP01 and LP11 mode interferences in high-birefringence （Hi-Bi） panda fibers are theoretically and experimentally presented. The propagation characteristics of both the fundamental and second-order modes in Hi-Bi panda fibers are investigated, and the interference output intensity distribution of the LP₀1 and LP₁1 modes in panda fibers are thoroughly examined. An experiment is conducted to verify the feasibility of modal interference sensors. The results show that the two-lobe interference pattern of panda fibers generates energy exchanges when external strain is applied on the fiber. Moreover, Hi-Bi panda fibers can be used to design voltage sensors.     

Fiber-optic vector vibroscope

A directional vibration sensor based on polarization-controlled cladding-to-core recoupling is demonstrated. A compact structure in which a short section of multi-mode fiber (MMF) stub containing a weakly tilted fiber Bragg grating (TFBG) is spliced to another single-mode fiber without any lateral offset. Multiple core modes of the MMF are coupled at the junction and appear as well defined resonances in reflection from the TFBG. Some of those resonances exhibit a strong polarization and bending dependence. Both the orientation and the amplitude of the vibrations can be determined unambiguously via dual-path power detection of the orthogonal-polarimetric lowest order LP(1n) modes. Meanwhile, the unwanted power fluctuations and temperature perturbations can be referenced out by monitoring the fundamental LP(01) mode resonance.     

Fiber laser with combined feedback of core and cladding modes assisted by an intracavity long-period grating

We present a fiber laser made in a single piece of conventional doped-core fiber that operates by combined feedback of the fundamental core mode LP((0,1)) and the high-order cladding mode LP((0,10)). The laser is an all-fiber structure that uses two fiber Bragg gratings and a long-period grating to select the modes circulating in the cavity; the laser emits at the coupling wavelength between the core mode LP((0,1)) and the counterpropagating cladding mode LP((0,10)) in the Bragg gratings. This work demonstrates the feasibility of high-order mode fiber lasers assisted by long-period gratings.     

基于非线性光纤环形镜的少模脉冲幅度调制再生器

随着网络带宽需求的快速增加,波分复用系统的容量已接近非线性香农极限.为了适应未来网络的发展,空分复用技术引起了越来越多的关注.本文首次提出基于少模非线性光纤环形镜(FM-NOLM)的脉冲幅度调制(PAM)全光再生器,描述了其工作原理和具体设计过程.采用COMSOL软件对组成FM-NOLM的硫化物高非线性光纤进行了模式特性仿真.以LP01,LP11,LP21三个光纤模式为例,确定了再生器的参数,计算出每个模式的功率转移函数曲线.仿真分析了该少模PAM-4全光再生器的噪声抑制(NRR)性能,并与单模情形进行了比较.研究表明,1)对于每个空间模式的PAM信号,所有再生电平具有一致的功率转移性能;2)当输入信噪比(SNR)约大于20 dB时,三种模式的噪声抑制比均可超过3 dB,并随着输入信噪比线性增加,其斜率约为1.2;3)在相同输入SNR条件下,三种模式的噪声抑制比相差不大,不超过1.1 dB.为了说明再生器的再生性能,当输入SNR为25 dB时,我们还给出了再生前后PAM-4信号的功率分布直方图.与现有的再生方案相比,本文方案的均匀多电平再生转移性能,使其更适合高频谱效率的长距空分复用系统和任意电平数的PAM信号再生.此外,该方案也能够扩展到波长域,有效提高光通信系统的传输容量.     

光纤激光器反馈耦合损耗分析

将双包层光纤基模LP01模近似表示为拉盖尔-高斯光束的线性叠加,前六阶的拉盖尔-高斯光束包含了LP01模能量的99.99％.利用拉盖尔-高斯光束的传输特性计算了腔镜分别为球面镜和透镜加平面反射镜时的反馈耦合损耗.结果表明,腔镜为球面镜时,只有当球面镜和到达球面镜光束的曲率半径匹配时才能获得最小的耦合损耗,特别是当平面镜紧贴光纤端面时,耦合损耗为0;当腔镜为透镜加平面反射镜时,将平面镜放置在透镜焦平面时获得最小反馈耦合损耗为0.25％.     

Fiber-based Bessel beams with controllable diffraction-resistant distance

We experimentally generate n=0 Bessel beams via higher-order cladding mode excitation with a long period fiber grating. Our method allows >99% conversion efficiency, wide or narrow conversion bandwidth, and accurate control of the number of rings in the beam. This latter property is equivalent to tuning the beam cone angle and allows for control of width and propagation distance of the center spot. We generate Bessel-like beams from LP(0,5) to LP(0,15) cladding modes and measure their propagation-invariant characteristics as a function of mode order, which match numerical simulations and a simple geometric model. This yields a versatile tool for tuning depth of focus out of fiber tips, with potential uses in endoscopic microscopy.     

Ultrashort-pulse investigation of the propagation properties of the LP(11) mode in 1.55-mum communication fibers

The coupling of an ultrashort laser pulse into a single-mode optical communication fiber gives rise to two propagating pulses as a result of the excitation of two guided modes, the fundamental, LP(01) , and the leaky, LP(11) . Such a phenomenon provides a new approach to the study of the propagation properties of the LP(11) mode. An experiment with tunable 110-fs pulses at a wavelength near 1550 nm is described. Information about the group velocity, the polarization-rotation length, the attenuation coefficient, and the cutoff wavelength of the LP(11) mode is obtained in a simple and direct way for various fibers.     

Coherent acousto-optic mode coupling in dispersion-compensating fiber by two acoustic gratings with orthogonal vibration directions

The acousto-optic mode coupling from core to LP11(cl) mode of a dispersion-compensating fiber excited by two acoustic waves with orthogonal perturbations is studied by use of a novel composite piezoelectric transducer. Highly polarization-dependent mode-selective spectra are observed that are due to coherent acousto-optic coupling between the core and various constituent cladding modes. Potential applications for implementing an all-fiber wavelength-tunable polarization analyzer are also discussed.     

折射率不敏感的级联型单模-少模-单模光纤温度传感器

提出了一种折射率不敏感的级联型单模-少模-单模光纤温度传感器。在制作传感器的过程中,设置熔接电流为100 mA,通过将少模光纤与单模光纤进行无错位熔接,以激发稳定的传输模式,形成光纤马赫-曾德尔干涉仪。由于外界环境的改变会引起少模光纤中不同模式之间相位差的改变,从而导致干涉条纹的漂移,因此通过检测干涉条纹的漂移量就可以实现待测参数的检测。少模光纤可以传输LP₀₁,LP₁₁,LP₂₁,LP₀₂共四种模式的光。实验中对长度为81.5 mm的传感器光谱进行分析可知,发生干涉的两个模式主要是LP₀₁模和LP₁₁模。利用该长度的级联型单模-少模-单模光纤传感器进行折射率和温度传感实验,结果表明,随着传感器温度不断的增加,其传输光谱出现了明显的蓝移现象,在27.6~93.8 ℃的温度变化范围内,灵敏度高达-85.9 pm·℃-1,且具有较好的线性度;在甘油折射率为1.347 1~1.443 9变化范围内,其传输光谱没有出现明显的漂移现象,灵敏度仅为3.697 34 nm·RIU-1,具有折射率不敏感特性。因此,相对于传统的包层模干涉型与多模干涉型光纤传感器,所提出的基于FMF的传感器更易于实现对传输模式的控制与分析,且具有结构简单、易于制备、灵敏度高等优点,能够避免温度与折射率同测的交叉敏感问题,可用于电力系统、生物医学、航空航天等领域的温度检测。     

基于无芯-少模-无芯光纤结构的温度传感特性研究北大核心CSCD

提出了一种基于无芯-少模-无芯光纤结构的温度传感器,对传感器进行了理论分析和实验研究。该传感器将无芯光纤(coreless fiber,CLF)与少模光纤(few-mode fiber,FMF)同轴熔接,构建无芯-少模-无芯的光纤结构,结构两端熔接单模(single mode fiber,SMF)光纤作为输入输出光纤,第1段无芯光纤与单模光纤的模式失配起到激发高阶模的作用,少模光纤中的LP01与LP11两种模式沿少模光纤纤芯传输,在第2段无芯光纤的作用下LP01与LP11两种模式重新耦合回单模光纤,LP01与LP11两种模式发生干涉,形成干涉光谱。当外界温度变化时,两种模式的光程差发生变化,干涉光谱的干涉波谷发生漂移,选取2个不同的干涉波谷作为特征波长,进行实验分析。实验结果表明:波长在1550 nm和1534 nm附近的干涉谷均发生红移,相应的温度灵敏度分别为68 pm/℃和44.5 pm/℃。该传感结构制作简单、灵敏度高,有很好的应用前景。     

多叶应力区扭转光纤的耦合模理论

从线性极化模的耦合模理论出发,分析了双叶应力区扭转光纤,即扭转保偏光纤,和四叶应力区扭转光纤.推导应力引起的在光纤芯区各向异性的介质张量表达式;利用该表达式得到线性极化模在有转角时的多叶应力区光纤中传输的耦合模方程;从而推得多叶应力区扭转光纤中的超本地模,由超本地模的相位常数来确定该光纤的双折射.在双叶、四叶应力区理想对称的条件下,前者可以得到较高的椭圆双折射,而后者则无任何双折射.同样的结论可推广到8叶或16叶的扭转光纤,都无任何双折射.     

Bragg grating resonances in all-solid bandgap fibers

Bragg gratings are fabricated in all-solid photonic bandgap fibers by forming a longitudinal periodic index modulation over the high-index rod lattice in the cladding. Due to its unique index-modulation pattern and the modal properties of the fiber, resonance couplings to the LP(01) supermodes (also known as high-index rod modes) are observed. The corresponding peak is located at the long-wavelength side of the Bragg wavelength and presents the highest depth. The asymmetric index profile over the high-index rods, which is induced by side UV illumination, leads to broadening of the supermode resonance peaks and variation with fiber orientation in the bend response of the fiber grating.