Three-dimensional multi-phase simulation of the mixing and segregation of binary particle mixtures in a two-jet spout fluidized bed

This study presents a three-dimensional numerical study of the mixing and segregation of binary particle mixtures in a two-jet spout fluidized bed based on an Eulerian–Eulerian three-fluid model. Initially, the particle mixtures were premixed and packed in a rectangular fluidized bed. As the calculation began, the gas stream was injected into the bed from the distributor and jet nozzles. The model was validated by comparing the simulated jet penetration depths with corresponding experimental data. The main features of the complex gas–solid flow behaviors and the mechanism of mixing and segregation of the binary mixtures were analyzed. Moreover, further simulations were carried out to evaluate the effects of operating conditions on the mixing and segregation of binary particle mixtures. The results illustrate that mixing can be enhanced by increasing the jet velocity or enlarging the difference of initial proportions of binary particle mixtures.     

Experimental and computational studies on flow behavior of gas–solid fluidized bed with disparately sized binary particles

This paper presents experimental and computational studies on the flow behavior of a gas-solid fluidized bed with disparately sized binary particle mixtures. The mixing/segregation behavior and segregation efficiency of the small and large particles are investigated experimentally. Particle composition and operating conditions that influence the fluidization behavior of mixing/segregation are examined. Based on the granular kinetics theory, a multi-fluid CFD model has been developed and verified against the experimental results. The simulation results are in reasonable agreement with experimental data. The results showed that the smaller particles are found near the bed surface while the larger particles tend to settle down to the bed bottom in turbulent fluidized bed. However, complete segregation of the binary particles does not occur in the gas velocity range of 0.695-0.904 m/s. Segregation efficiency increases with increasing gas velocity and mean residence time of the binary particles, but decreases with increasing the small particle concentration. The calculated results also show that the small particles move downward in the wall region and upward in the core. Due to the effect of large particles on the movement of small particles, the small particles present a more turbulent velocity profile in the dense phase than that in the dilute phase.     

Three-dimensional multi-phase simulation of the mixing and segregation of binary particle mixtures in a two-jet spout fluidized bed

This study presents a three-dimensional numerical study of the mixing and segregation of binary particle mixtures in a two-jet spout fluidized bed based on an Eulerian-Eulerian three-fluid model.Initially,the particle mixtures were premixed and packed in a rectangular fluidized bed.As the calculation began,the gas stream was injected into the bed from the distributor and jet nozzles.The model was validated by comparing the simulated jet penetration depths with corresponding experimental data.The main features of the complex gas-solid flow behaviors and the mechanism of mixing and segregation of the binary mixtures were analyzed.Moreover,further simulations were carried out to evaluate the effects of operating conditions on the mixing and segregation of binary particle mixtures.The results illustrate that mixing can be enhanced by increasing the jet velocity or enlarging the difference of initial proportions of binary particle mixtures.     

Experimental and computational studies on flow behavior of gas-solid fluidized bed with disparately sized binary particles

This paper presents experimental and computational studies on the flow behavior of a gas-solid fluidized bed with disparately sized binary particle mixtures. The mixing/segregation behavior and segregation efficiency of the small and large particles are investigated experimentally.Particle composition and operating conditions that influence the fluidization behavior of mixing/segregation are examined. Based on the granular kinetics theory, a multi-fluid CFD model has been developed and verified against the experimental results. The simulation results are in reasonable agreement with experimental data. The results showed that the smaller particles are found near the bed surface while the larger particles tend to settle down to the bed bottom in turbulent fluidized bed. However, complete segregation of the binary particles does not occur in the gas velocity range of 0.695--0.904 m/s. Segregation efficiency increases with increasing gas velocity and mean residence time of the binary particles, but decreases with increasing the small particle concentration. The calculated results also show that the small particles move downward in the wall region and upward in the core. Due to the effect of large particles on the movement of small particles, the small particles present a more turbulent velocity profile in the dense phase than that in the dilute phase.     

Numerical simulation of gas–solid flow with two fluid model in a spouted-fluid bed

The flow characteristics in a spouted-fluid bed differ from those in spouted or fluidized beds because of the injection of the spouting gas and the introduction of a fluidizing gas. The flow behavior of gas–solid phases was predicted using the Eulerian–Eulerian two-fluid model (TFM) approach with kinetic theory for granular flow to obtain the flow patterns in spouted-fluid beds. The gas flux and gas incident angle have a significant influence on the porosity and particle concentration in gas–solid spouted-fluid beds. The fluidizing gas flux affects the flow behavior of particles in the fountain. In the spouted-fluid bed, the solids volume fraction is low in the spout and high in the annulus. However, the solids volume fraction is reduced near the wall.     

CFD-DEM simulation of spouting of corn-shaped particles

Three dimensionally coupled computational fluid dynamics (CFD) and discrete element method (DEM) were used to investigate the flow of corn-shaped particles in a cylindrical spouted bed with a conical base. The particle motion was modeled by the DEM, and the gas motion by the k-? two-equation turbulent model. A two-way coupling numerical iterative scheme was used to incorporate the effects of gas–particle interactions in terms of momentum exchange. The corn-shaped particles were constructed by a multi-sphere method. Drag force, contact force, Saffman lift force, Magnus lift force, and gravitational force acting on each individual particle were considered in establishing the mathematical modeling. Calculations were carried out in a cylindrical spouted bed with an inside diameter of 200 mm, a height of 700 mm, and a conical base of 60°. Comparison of simulations with experiments showed the availability of the multi-sphere method in simulating spouting action with corn-shaped particles, but it depended strongly on the number and the arrangement of the spherical elements. Gas–solid flow patterns, pressure drop, particle velocity and particle concentration at various spouting gas velocity were discussed. The results showed that particle velocity reaches a maximum at the axis and then decreases gradually along the radial direction in the whole bed. Particle concentration increases along the radial direction in the spout region but decreases in the fountain region, while it is nearly constant in the annulus region. Increasing spouting gas velocity leads to larger pressure drop, remarkably increased speed of particle moving upward or downward, but decreased particle concentration.     

Numerical simulation of gas-solid flow with two fluid model in a spouted-fluid bed

The flow characteristics in a spouted-fluid bed differ from those in spouted or fluidized beds because of the injection of the spouting gas and the introduction of a fluidizing gas. The flow behavior of gas-solid phases was predicted using the Eulerian-Eulerian two-fluid model （TFM） approach with kinetic theory for granular flow to obtain the flow patterns in spouted-fluid beds. The gas flux and gas incident angle have a significant influence on the porosity and particle concentration in gas-solid spouted-fluid beds. The fluidizing gas flux affects the flow behavior of particles in the fountain. In the spouted-fluid bed, the solids volume fraction is low in the spout and high in the annulus. However, the solids volume fraction is reduced near the wall.     

Simulated configurational temperature of particles and a model of constitutive relations of rapid-intermediate-dense granular flow based on generalized granular temperature

In gas–solid flat-base spout bed with a jet, the flow of particles must go through an intermediate regime where both kinetic/collisional and frictional contributions play a role. In this paper, the statistical framework is proposed to define the generalized granular temperature which sums up the configurational temperature and translational granular temperature. The configurational temperature, translational and rotational granular temperatures of particles are simulated by means of CFD-DEM (discrete element method) in a 3D flat-base spout bed with a jet. The configurational temperatures of particles are calculated from instantaneous overlaps of particles. The translational and rotational granular temperatures of particles are calculated from instantaneous translational and angular velocities of particles. Roughly, the simulated translational and rotational granular temperatures increase, reach maximum, and then decrease with the increase of solids volume fractions. However, the configurational temperature increases with the increase of solids volume fractions. At high solid volume fraction, the predicted configurational temperatures are larger than the translational and rotational granular temperatures, indicating that the rate of energy dissipation do contributes by contact deformation of elastic particles. The generalized granular temperature is proposed to show the relation between the variance of the fluctuation velocity of deformation and the variance of the translational fluctuation velocity of particles. The constitutive relations of particle pressure, viscosity, granular conductivity of fluctuating energy and energy dissipation in rapid-intermediate-dense granular flows are correlated to the generalized granular temperature. The variations of particle pressure, shear viscosity, energy dissipation and granular conductivity are analyzed on the basis of generalized granular temperature in a flat-base spout bed with a jet. The axial velocities of particles predicted by a gas–solid two-fluid model of rapid-intermediate-dense granular flows agree with experimental results in a spout bed.     

Multi-fluid modeling of density segregation in a dense binary fluidized bed

This paper presents simulation results of the density segregation in a dense binary gas fluidized bed using a multi-fluid model from Chao et al. (2011). The segregation behavior of two types of particles with approximately same particle diameters and different particle densities was studied and validated using the experimental data from Formisani et al. (2008). Some detailed information regarding the gas, particle velocity profiles, the distributions of the particle volume fractions and the flotsam-to-total particle volume fraction ratios is presented. The simulation results show that the simulated axial average flotsam-to-total particle volume fraction ratio distribution agrees reasonably with the experimental data of Formisani et al. (2008). The binary particle velocities are closely coupled though the segregation exists. The segregation behavior and the particle velocity profiles are superficial gas velocity dependent. The number and distribution of particle velocity vortices change dramatically with superficial gas velocity: at a comparatively low superficial gas velocity, the particles mainly segregate axially, and at a comparatively high superficial gas velocity, the particles segregate both axially and radially.     

NUMERICAL SIMULATIONS OF HYDRODYNAMIC BEHAVIORS IN CONICAL SPOUTED BEDS

The axial and radial distributions of static pressures and vertical particle velocities of conical spouted beds have been simulated and compared with experimental data. Simulation results show that, among all factors investigated, the Actual Pressure Gradient (the APG term) in conical spouted beds, introduced as the default gravity term plus an empirical axial solid phase source term, has the most significant influence on static pressure profiles, followed by the restitution coefficient and frictional viscosity, while other factors almost have no effect. Apart from the solid bulk viscosity, almost all other factors affect the radial distribution of the axial particle velocity, although the influence of the APG term is less significant. For complex systems such as conical spouted beds where a fluidized spout region and a defluidized annulus region co-exist, the new term introduced in this work can improve the CFD simulation. Furthermore, for other systems with the Actual Pressure Gradient different from either fluidized beds or packed beds, the new approach can also be applied.     

Influences of the fluidizing and spouting pulsation on particle motion in spout-fluid beds

Effects of variable airflow on particle motion in spout-fluid beds are studied. Computational fluid dynamics using Navier–Stokes equations for the gas phase coupled with the discrete element method using Newton’s laws for the solid phase have been employed. Results indicate that increasing the fluidizing velocity diminishes dead zones and increases both the total height of the bed and the traversed distance by particles in the steady spout-fluid bed. In pulsed airflows, two configurations are investigated, namely, the spouted pulsed-fluidized bed with pulsed flow of the fluidizing velocity, and the pulsed-spouted fluidized bed with pulsed flow of the spouting velocity. The positive effect of pulsation on particle motion is shown and the effects of parameters, such as amplitude and frequency, on the dynamics of the bed are investigated in each configuration. An increase of up to 19% in traversed distance is found for the range studied, which suggests flow pulsation as a promising technique for increasing particle mixing in spout-fluid beds.     

LBM-DEM四向耦合喷动床内介尺度模拟与分析

研究喷动床内颗粒的流动特性对于喷动床的设计和优化具有重要意义。基于气固两相流流动的LBM-DEM四向耦合模型,对单孔射流喷动床中颗粒的流动进行数值模拟。其中,气相采用修正的格子玻尔兹曼方法,颗粒相采用离散单元法,流固之间受力的双向耦合基于牛顿第三定律,颗粒与颗粒及颗粒与壁面的受力双向耦合采用软球模型。模拟得到了流化过程、颗粒与气体的速度分布、床层膨胀高度变化以及床宽对流化过程的影响。结果表明,喷动床内存在强烈的内循环,床宽增加导致颗粒运动能力减弱,射流速度增加使颗粒运动更加剧烈,床层膨胀高度增加。     

回转窑多粒径颗粒流动与偏析的DEM模拟与实验研究

为明晰回转窑内颗粒的运动行为及偏析机理,以绿豆、黄豆和黑豆为颗粒介质,依次对3种装填顺序下的颗粒流动过程进行离散元模拟与实验研究,以颗粒质量分数和平均粒度为判据,对颗粒偏析进行评价。结果表明,回转窑内颗粒流动区可分为自由滚落区、渗流呆滞区以及窑壁携带区,自由滚落区颗粒流速最大,而渗流呆滞区流速最小。窑内颗粒沿轴向输运过程发生径向偏析,形成夹层结构,小颗粒受渗流作用在渗流呆滞区中心形成内核,大粒径和中等粒径颗粒集中在自由滚落区和窑壁携带区。窑内颗粒力链分布不均匀,强力链分布于近窑壁区,弱力链分布于自由滚落区和渗流呆滞区,且渗流呆滞区力链细而密集。当窑头附近不同粒径颗粒存在轴向速度差时,颗粒在轴向发生掺混,并产生径向偏析。     

Particle size distribution in CPFD modeling of gas–solid flows in a CFB riser

A computational particle fluid dynamics (CPFD) numerical method to model gas–solid flows in a circulating fluidized bed (CFB) riser was used to assess the effects of particle size distribution (PSD) on solids distribution and flow. We investigated a binary PSD and a polydisperse PSD case. Our simulations were compared with measured solids concentrations and velocity profiles from experiments, as well as with a published Eulerian-Eulerian simulation. Overall flow patterns were similar for both simulation cases, as confirmed by experimental measurements. However, our fine-mesh CPFD simulations failed to predict a dense bottom region in the riser, as seen in other numerical studies. Above this bottom region, distributions of particle volume fraction and particle vertical velocity were consistent with our experiments, and the simulated average particle diameter decreased as a power function with riser height. Interactions between particles and walls also were successfully modeled, with accurate predictions for the lateral profiles of particle vertical velocity. It was easy to implement PSD into the CPFD numerical model, and it required fewer computational resources compared with other models, especially when particles with a polydisperse PSD were present in the heterogeneous flow.     

Constraint strength and axial/radial particle velocity profiles for an integrated riser outlet

To study axial/radial profiles of particle velocity in the affected region of an integrated riser outlet, a cold model was developed for the integrated riser reactor combining the gas–solid distributor with the fluidized bed. Constraints, related to the gas–solid distributor and the upper fluidized bed, imposed on the particle flow in the riser outlet region, were investigated experimentally. The experimental results showed that with increasing superficial gas velocity, these constraints have strong influences on particle flow behavior, the particle circulation flux in the riser, and the height of the static bed material of the upper fluidized bed. When the constraints have greater prominence, the axial profile of the cross-sectionally averaged particle velocity in the outlet region initially increases and then decreases, the rate of decrease being proportional to the constraint strength. Along the radial direction of the outlet section, the region where the local particle velocity profile tends to decrease appears near the dimensionless radius r/R = 0.30 initially and then, with increasing constraint strength, gradually extends to the whole section from the inner wall. Based on the experimental data, an empirical model describing the constraint strength was established. The average relative error of the model is within 7.69%.     

Hydrodynamic behavior of magnetized fluidized beds with admixtures of Geldart-B magnetizable and nonmagnetizable particles

This work focuses on the hydrodynamic behavior of admixtures of Geldart-B magnetizable and nonmagnetizable particles in a magnetized fluidized bed. The applied magnetic field was axial, uniform, and steady. In operating the beds, the magnetization-LAST mode was adopted under which four distinct flow regimes exist: fixed, magnetized-bubbling, partial segregation-bubbling, and total segregation-bubbling. The operational phase diagram was drawn to display the transitions between flow regimes in an intuitive manner. Only in the magnetized-bubbling regime could the magnetic field reduce the bubble size and improve fluidization quality. In the segregation-bubbling regimes, fluidization quality deteriorated as segregation developed. The segregation of the binary mixture was quantitatively studied by observing pressure drops in the local bed. Reasons for the improvement in fluidization quality as well as the occurrence of segregation were analyzed. Furthermore, the flow regime transition under magnetization-LAST operation mode was different from that under magnetization-FIRST mode. The magnetically stabilized bed (MSB) flow regime, which could be easily created under magnetization-FIRST mode, could no longer be achieved under magnetization-LAST mode. With the admixture, the MSB was proved to be a metastable equilibrium state. Under the magnetization-LAST mode, the admixture bed reached directly the stable equilibrium state—bubbling with segregation.     

Particle size distribution in CPFD modeling of gas-solid flows in a CFB riser

A computational particle fluid dynamics(CPFD) numerical method to model gas-solid flows in a circulating fluidized bed(CFB) riser was used to assess the effects of particle size distribution(PSD) on solids distribution and flow.We investigated a binary PSD and a polydisperse PSD case.Our simulations were compared with measured solids concentrations and velocity profiles from experiments,as well as with a published Eulerian-Eulerian simulation.Overall flow patterns were similar for both simulation cases,as confirmed by experimental measurements.However,our fine-mesh CPFD simulations failed to predict a dense bottom region in the riser,as seen in other numerical studies.Above this bottom region,distributions of particle volume fraction and particle vertical velocity were consistent with our experiments,and the simulated average particle diameter decreased as a power function with riser height.Interactions between particles and walls also were successfully modeled,with accurate predictions for the lateral profiles of particle vertical velocity.It was easy to implement PSD into the CPFD numerical model,and it required fewer computational resources compared with other models,especially when particles with a polydisperse PSD were present in the heterogeneous flow.     

Constraint strength and axial/radial particle velocity profiles for an integrated riser outlet

To study axial/radial profiles of particle velocity in the affected region of an integrated riser outlet,a cold model was developed for the integrated riser reactor combining the gas-solid distributor with the fluidized bed.Constraints,related to the gas-solid distributor and the upper fluidized bed,imposed on the particle flow in the riser outlet region,were investigated experimentally.The experimental results showed that with increasing superficial gas velocity,these constraints have strong influences on particle flow behavior,the particle circulation flux in the riser,and the height of the static bed material of the upper fluidized bed.When the constraints have greater prominence,the axial profile of the cross-sectionally averaged particle velocity in the outlet region initially increases and then decreases,the rate of decrease being proportional to the constraint strength.Along the radial direction of the outlet section,the region where the local particle velocity profile tends to decrease appears near the dimensionless radius r/R = 0.30 initially and then,with increasing constraint strength,gradually extends to the whole section from the inner wall.Based on the experimental data,an empirical model describing the constraint strength was established.The average relative error of the model is within 7.69%.     

Nanoparticle dispersion and coagulation in a turbulent round jet

Nanoparticle dispersion and coagulation behaviors in a turbulent round jet were studied in this article. An experimental system was designed to generate a uniformly distributed air–nanoparticle two-phase flow in a turbulent round jet. The particle size distribution (PSD) was measured by a scanning mobility particle sizer (SMPS) in the near field of the jet. The particle diameters were nearly constant in the potential core due to the high carrying velocity and laminar characteristic of the flow but grew larger in the region of high turbulence intensities because the vortex structures in the mixing layer promoted coagulation. Furthermore, the migration property of small-sized nanoparticles forced them to be preserved in the potential core also leading to the diameter increase. The comparison of the particle concentration distributions at different sections indicated that the shear layer is the major region for the mixing of particle-laden stream and ambient air. The particle diameters in the axial direction experienced three stages including a slightly changed stage, an increasing stage and a constant stage. The diameter increase should be attributed to turbulence coagulation.     

A laser-fluorescence technique for turbulent two-phase flow measurements

A non-intrusive measurement technique has been developed for accurate determination of gas and particle velocities in a turbulent two-phase flow field. The principle of the technique is based on the discrimination between the scattered light from particles and the fluorescence emission from particles coated with a fluorescent dye. A high-powered, argon-ion based, single-channel, on-axis backscatter laser-Doppler velocimetry system was used. The fluorescent dye was Rhodamine 6G. A study of the gas-solid two-phase flow behaviour in the freeboard of a cold gas-fluidized bed was undertaken. The solid phase contained two particle groups: bed material (sand) and fuel particles (wood). Measurements of the axial velocity and turbulence intensity distributions of the gas phase and both particle groups within the solid phase were made along the column centre and across the freeboard. Excellent discrimination of velocities from the two phases and from the two particle groups within the solid phase was achieved.