Realization and properties of ramp-type YBa2Cu3O7−δ/Au/Nb junctions

All-thin-film ramp type Josephson junctions between YBa₂Cu₃O_7−δ and Nb have been fabricated. This procedure allows connections between high-T_c and low-T_c superconductors at different crystal sides of the high-T_c superconductor on one chip, which is of great interest for novel phase devices. A thin Au layer is incorporated as a chemical barrier to avoid oxygen transfer from the YBa₂Cu₃O_7−δ to the Nb. Critical current densities up to 600 A/cm² are obtained at T=4.2 K, with typical R_nA values of 0.8 μΩ cm². The variation of the magnetic field dependence of the critical current with the angle between the junction barrier and the YBa₂Cu₃O_7−δ crystal axes is explained by considering a predominant d_x²−y² order parameter symmetry of the YBa₂Cu₃O_7−δ. The successful fabrication of these junctions allows the implementation of novel superconducting electronics, such as complementary Josephson circuitry or proposed qubit concepts, using the unconventional order parameter symmetry of the high-T_c superconductor.     

Positron annihilation in the hydrogenated granular superconductor of YBa2Cu3O7−δ

In this paper, we have used the sputtering neutral-particles mass spectroscopy (SNMS) and positron-annihilation technique to investigate the effect of hydrogenation on the physical properties of different oxygenated YBa₂Cu₃O_7−δ superconductors. Under the same of hydrogenation treatment, the hydrogenation effects on the superconductors are compared to the non-superconductors. It was shown that the hydrogen concentration in the superconductors is about eight times of the non-superconductor's. It was proven that the long lifetime of positrons in the annihilation process is determined by the variation of the concentrations of monovacancies and microvoids, which takes place in both of intragrain and intergrain samples. The hydrogenation effect can be classified into four stages. At the first stage, the hydrogen atoms fill both monovacancy and microvoid. At the end of the first stage, the long lifetime τ₂ reaches the maximum value which is determined by the lifetime of the positron in the monovacancy-free and nearly microvoid-exhausted YBCO sample. In the second stage, the hydrogen charging will lead to creation of new monovacancies; this will make the long lifetime τ₂ drop monotonically to its minimum value. In the third stage, further hydrogen charging promotes the formation of microvoids, and leads to an increasing τ₂ up to a saturation value, which indicates the equilibrium concentrations of monovacancy and microvoid at that temperature.     

Ramans study of Y1−xPrxBa2Cu3O7−δ and YB2Cu3−xZnxO7−δ single crystals

Single crystals with known T_c values of Y_1−xPr_xBa₂Cu₃O_7−δ (Y---Pr1:2:3) and YBa₂Cu_3−xZn_3−xZn_xO_7−δ (Y---Zn1:2:3) systems are studied by Raman measurements. The Raman spectra for (Y---Pr1:2:3) single crystals show that the frequencies of Ba and O_z modes increase as the Pr content increases. The results are consistent with the hole-localization scheme proposed for the suppression of superconductivity in the polycrystalline Y---Pr1:2:3 systems. On the other hand, in the Y---Zn1:2:3 system, all the Raman modes do not change in frequencies. However, the FWHM of the Cu(2) mode increases with the decrease of T_c, indicating strong scattering of charge carriers by the substituted Zn ions in the CuO₂ planes. The induced disorder in the CuO₂ planes may be related with suppression of T_c in the Y---Zn1:2:3 system. Thus, the suppression mechanism in the Y---Zn1:2:3 systems seems to be different from that in the Y---Pr1:2:3 systems.     

The crystallographic symmetries of single BaPb1−xBixO3 crystals grown from BaCO3-PbO2-Bi2O3 solutions

Single crystals of Perovskite-type oxide BaPb_1−xBi_xO₃ are grown from BaCO₃-PbO₂-Bi₂O₃ solutions which are weighed in two kinds of mixing ratios: X/2 mol % BaCO₃ − (100−X) mol % PbO₂ − X/2 mol % Bi₂O₃ and (10+X/2) mol % BaCO₃ − (90−X) mol % PbO₂ − X/2 mol % Bi₂O₃ These room temperature crystal structures are examined by using an X-ray powder diffraction method. The crystals grown from X/2−(100−X)−X/2 mol % solutions are orthorhombic at room temperature, while the structures are tetragonal with crystals grown from relatively Ba rich and Pb poor ( (10+X/2)−(90−X)−X/2 mol % ) solutions. This result indicates that the difference in the mixing ratio of the initial materials brings about a drastic structural change. The orthorhombic and the tetragonal crystals of x0.25 exhibit superconducting transition at 10K and 12K, respectively. The transition temperature in the latter is 2K higher than the former. In the light of this result, some difference between orthorhombic and tetragonal crystals is considered to influence superconductivity in this system.     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Fabrication and growth rate estimation of PrBa2Cu3O7−δ single crystal by the modified top seeded crystal pulling method

Recently, we succeeded in fabricating single crystals of PrBa₂Cu₃O_7−δ by a modified top seeded crystal pulling method called the SRL-CP (Solute Rich Liquid-Crystal Pulling) method. Y₂O₃ and MgO polycrystalline crucibles and a MgO single crystal crucible were used to grow the single crystals. The crystal growth temperature was set in the range of 968°C to 972°C. The grown crystals were identified as PrBa₂Cu₃O_7−δ by X-ray diffraction. In the case of using Y₂O₃ crucibles the composition of the grown crystals was Y_xPr_1−xBa₂Cu₃O_7−δ (0.48 < x < 0.57) and in the case of using MgO crucibles a relatively small amount of Mg contamination to the grown crystals occurred at a typical concentration of approximately 1 at.% of the sum of cations. According to the crystal growth model of the SRL-CP method [1–5], a maximum growth rate of 1.7 × 10⁻⁵ cm/s was calculated with the aid of the phase diagram studies we reported earlier [6]. This value is reasonably in agreement with the experimental results.     

Superconductivity and crystallographic properties of La2 − xMxCuO4 − δ (M = Na, K)

Superconductivity and crystallographic properties of La_{2 − x}M_xCuO_{4 − δ} (M = Na, K) are studied. In the La_{2 − x}M_xCuO_{4 − δ} system, superconductivity is detected for x 0.2. Oxygen content analysis shows that the system has more oxygen vacancies than the La_{2 − x}Sr_xCuO_{4 − δ} system. These oxygen vacancies may reduce the hole concentration, and high Na-doping is needed to produce superconductivity. In the La_{2 − x}K_xCuO_{4 − δ} system, superconductivity is observed for the first time. Resistivity and magnetic susceptibility measurements show that T_c(onset) is 40 K and the Meissner volume fraction is about 4% for x = 0.7. The system changes from orthorhombic to a tetragonal K₂NiF₄ structure at x ≈ 0.3 and only tetragonal samples show superconductivity.     

Systematic thermopower measurements of the thallium cuprates Tl(Ba,Sr)2Cam−1CumO2m+3−δ and Tl2Ba2Cam−1CumO2m+4+δ

The thermoelectric power (TEP) S versus temperature has been systematically investigated for several series of the superconducting cuprates Tl(Ba,Sr)₂Ca_m−1Cu_mO_2m+3−δ (m = 2, 3) and Tl₂Ba₂Ca_m−1Cu_mO_2m+4+δ (m = 1, 2, 3). The consideration of the S(T_c) curves allows two important points to be found evidence for. The first one deals with the fact that all these superconducting thallium cuprates are systematically overdoped whatever T_c, and whatever the number of Cu or Tl layers; no underdoped superconducting cuprate could be obtained. The second point shows that there exist two classes of Tl cuprates: the weakly overdoped cuprates that exhibit a T_{c max} ≥ 100 K (all the triple copper layer cuprates and the 2212 cuprates) and those which can be heavily doped that exhibit a T_{c max} ≤ 90 K (the 2201 and the 1212 cuprates). The different behavior of thallium cuprates compared to YBa₂Cu₃O_7−δ and to bismuth cuprates is discussed.     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

Preparation and characterization of Y1−xPrxBa2Cu3O7−δ single crystals

We present a reliable method for growing single crystals of Y_1−xPr_xBa₂Cu₃O_7−δ high-T_c superconductors in ZrO₂ crucibles. This method results in crystals with greatly improved superconducting properties compared to crystals grown with the previously reported methods which use Al₂O₃ crucibles. We describe techniques for crystal growth in both Al₂O₃ and ZrO₂ crucibles using an excess of BaCo₃ and CuO as the flux. The crystals were characterized by means of DC magnetic-susceptibility measurements, electrical-resistivity measurements, and electron microprobe analysis. The effects of Al contamination on the conditions for crystal growth and on the superconducting properties of the crystals are found to be quite significant.     

High TcYBa2Cu3O7−δ superconducting transition-edge microbolometers

High T_c superconducting thin film YBa₂Cu₃O_7−δ (YBCO) bolometers have been fabricated on various substrates such as MgO, LaAlO₃, YSZ and Si using laser ablation technique. Performance of these IR bolometers operating with a Joule-Thomson refrigerator has been investigated. Measurements of the responsivity and low frequency noise near T_c in the current biased YBCO bolometers show that reliable devices can be fabricated. Measured noise equivalent power (NEP), for YBCO/YSZ bolometer, reaches 6 × 10⁻¹⁰W/Hz^1/2 at 165 Hz and has a responsivity of 60 V/W with a blackbody source. This performance is comparable to that of the optimized pyroelectric detectors. The characteristics of YBCO films deposited on Si substrates reveal that superconducting thin film multi-elements or focal plane array with silicon integrated readout circuit are feasible. Such bolometers exhibit NEP of 7 × 10⁻⁹W/Hz^1/2, and significant improvement appears possible. Electrical measurements show no noticeable film degradation after the bolometer is exposed to atmosphere for three months.     

The contribution of Bc mesons to the search for B → τ ντ decays at LEP

We study the contribution of B_c mesons to the search for B → τν_τ decays. We find that at LEP the contributions from B_u and B_c mesons can be comparable. This observation can have a relevant impact on the extraction of constraints on new physics (such as charged-Higgs contributions) from current LEP limits on B → τν final states. Inclusion of the B_c contribution can reduce the current L3 limit on tan β/M_H from 0.38 GeV⁻¹ (90% CL) down to 0.27 GeV⁻¹ (90% CL).     

Low field microwave absorption of YBa2Cu3O7−δ thin films

The modulated microwave absorption in YBa₂Cu₃O_7−δ thin films was studied as a function of temperature, modulation amplitude, and microwave power. The comparative nature of weak links in YBaCuO thin films, ceramics, and powders is discussed.     

Properties of nonstoichiometric Pr0.6−xSr0.4MnO3 as the cathodes of SOFCs

A series of samples Pr_0.6−xSr_0.4MnO₃ (x=0, 0.01, 0.05, 0.1, 0.15, 0.2) were synthesized by a solid state reaction method. Pr deficiency at the A site has a great effect on the properties of Pr_0.6−xSr_0.4MnO₃ as the cathode of SOFCs (solid oxide fuel cells). Compared to the commonly used La_0.6Sr_0.4MnO₃ and La_0.55Sr_0.4MnO₃ cathode, Pr_0.6−xSr_0.4MnO₃ is better in the properties of conductivity, overpotential and impedance. In all the samples, the one with x=0.05, Pr_0.55Sr_0.4MnO₃, revealed the best performance in the measured temperature range.     

Symmetry breaking and the decays ψ′ → J/ψπ(η) and J/ψ → η(η′) γ

The theoretical mechanisms for the decays ψ′ → ψπ⁰ and ψ′ → ψη, which violate SU₂ and SU₃, respectively discussed. It is argued that symmetry breaking in the decay amplitudes may be as important as π⁰ −η −η′ mixing. The π⁰ −η mechanism ψ′ → ψν → ψπ⁰ leads to Γ(ψ′ → ψπ⁰) = (3.3±1.0) × 10⁻³ Γ(ψ′ → ψν), but this number may be enhanced by a factor as large as 12 by π⁰−η′ mixing and isospin violation in the decay amplitude. The related decays ψ → ηγ and ψ → η′γ are also discussed.     

Structural and transport properties of the triple-layer compounds Ba4(Pb1−xBix)3O10 (0≤ x<0.3)

A series of new compounds Ba₄(Pb_1−xBi_x)₃O₁₀ with 0≤x<0.3 has been prepared and characterized by X-ray and electron diffraction. The d.c. resistivity vs. temperature data for different x values are presented and structural features are compared to those of the superconducting phase Ba(Pb_1−xBi_x)O₃. The “mother-compound” Ba₄Pb₃O₁₀ is tetragonal, with lattice constants A=0.4280(1) and C=3.017(1) nm. Its structure can be regarded as a stacking of Ba(PbBi)O₃ triple-layers, separated by single BaO layers. Electron diffraction reveals the presence of a weak superstructure with the a-axis related to that of the perovskite by a=√2a_p. Frequent intergrowth of this phase with the perovskite structure is observed. The conductivity of the samples Ba₄Pb₃O₁₀ is nearly independent of temperature, while Bi-doped samples exhibit semiconductor-like behaviour at low temperature. No superconducting transition is observed down to 2K.     

Estimation of the exchange constants in the Fe sublattice of the Y2Fe17 and Y2Fe17N3−δ compounds from the analysis of Mössbauer measurements

From the analysis of Mössbauer data for Y₂Fe₁₇ and Y₂Fe₁₇N_3−δ at various temperatures the hyperfine fields for 4f, 6g, 12j, 12k iron sites were estimated as a function of temperature. The reduced magnetizations calculated from the values of the hyperfine fields are fitted with a mean field model for four interacting sublattices using a computer program. The estimated exchange interaction from the fitting procedure between the 4f sites is found strongly negative (antiferromagnetic) in Y₂Fe₁₇ whereas in Y₂Fe₁₇N_3−δ it increases and becomes weak negative following a modified Slater-Néel curve. The rest of the exchange interactions are found positive or weak negative depending on the distances between the Fe atoms.     

Spectroscopic study of BixEu1−xVO4 and BiyGd1−yVO4 mixed oxides

The mixed oxides Bi_xEu_1−xVO₄ and Bi_yGd_1−yVO₄ crystallize in a zircon-type structure, for 0 <x < 0.6 and 0 < y < 0.64, and in a fergusonite-type structure, for 0.94 < x < 1 and 0.93 < y < 1. A process of competition between the dominant and the constrained effects of the lone-pair 6s² of Bi³⁺ is discussed. The diffuse reflectance spectroscopic studies of these mixed oxides are presented. The observed broad bands are attributed to charge transfer processes and the sharp peaks in the Bi_xEu_1−xVO₄ spectra are ascribed to intra-configurational 4f – 4ftransitions of the Eu³⁺ ion. The broad absorption shift in BiLnVO₄ (Ln : Eu and Gd) compounds to the longer wavelengths range, when Bi is introduced in the LnVO₄ lattice, is ascribed to charge transfer processes in a Bi-VO₄ center and are interpreted assuming a Jahn-Teller effect in the excited state of Bi³⁺. The concept of an internal pressure of Bi³⁺ ions is also used to explain the broad A-band shifts.