TiO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> binary xerogels: Synthesis and characterization

Silica/titania binary xerogels were prepared by joint hydrolysis of the ingredients. Gels of various compositions were characterized by ¹H NMR spectroscopy, IR spectroscopy, and thermogravimetry. The spectral characteristics of binary systems differ considerably from mere superposition of the spectra of the two constituent compounds and the spectrum of a mechanical mixture. A feasibility was demonstrated for controlling the acid properties of binary oxide gels via varying the component mole ratio.     

Synthesis and characterization of Co(OH)<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> nanotube composites as supercapacitor materials

A novel composite of Co(OH)₂ and TiO₂ nanotubes was synthesized by a chemical precipitation method. Co(OH)₂/TiO₂ nanotube composites and its microstructure were characterized by transmission electron microscopy (TEM), X-ray diffraction pattern (XRD). The electrochemical capacitance performance of this composite was investigated by cyclic voltammetry and charge–discharge tests with a three-electrode system in 6 M KOH solution. We synthesized different weight ratios of Co(OH)₂/TiO₂ nanotubes, a maximum specific capacitance of 229 F/g was obtained for the composite. Based on these tests, we propose that TiO₂ nanotubes provide the three-dimensional nanotube network structure for the composite and make the Co(OH)₂ dispersed. For these reasons, the TiO₂ nanotubes used as a framework for Co(OH)₂ improve the utilization of Co(OH)₂ greatly.     

Photocatalytic degradation of Br-trihalomethanes by nanosized TiO<Subscript>2</Subscript>/diatomite hybrid photocatalyst

Nanosized TiO₂/diatomite catalyst was prepared by sol–gel method at ambient temperature. Diatomite was used as a carrier, tetrabutyl titanate served as a source of titanium. The photocatalytic degradation of Br-THMs was successfully achieved in the presence of TiO₂/diatomite under Xe-light irradiation. It was suggested that Br-THMs were debromized in a stepwise manner. The rate of degradation increases markedly with increasing extent of substitution of Br-THMs by bromine because the C–Br bond is less stable than the C–Cl bond. Furthermore, the degradation of Br-THMs was caused by the action of hydroxyl free radicals, the signals of which were registered by means of electron spin resonance (ESR) spectroscopy.     

Charge separation by tetrahexahedron-SrTiO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> heterojunction as an efficient photocatalyst

Charge separation plays a key role in the conversion of solar energy into chemical energy for use in the redox reaction and as well as in the photocatalytic activity. In this study, SrTiO₃ particles with different morphologies including irregular, tetrahexahedron, and cube were synthesized by an in situ solvothermal method. The photocatalytic activity of the synthesized nanoparticles was investigated in the photocatalytic decomposition of methylene blue under UV light irradiation. Tetrahexahedron SrTiO₃ particles exhibited high decomposition activity (70 %), which is about two times higher than those of the irregular and cubic SrTiO₃ particles. The high decomposition activity of tetrahexahedron SrTiO₃ particles could be attributed to the improvement of charge separation achieved on different crystal facets. To reach a good charge separation, tetrahexahedron SrTiO₃/TiO₂ coupled nanoparticles were fabricated by impregnation method. Results showed that coupling tetrahexahedron SrTiO₃ with TiO₂ could produce efficient charge separation between tetrahexahedron SrTiO₃ and TiO₂ due to their matched band edges. In order to achieve better charge separation, the tetrahexahedron SrTiO₃/90 %TiO₂ sample was calcined at different temperatures in the 450–750 °C range. Tetrahexahedron SrTiO₃/90 %TiO₂ coupled nanoparticles calcined at 650 °C show high photocatalytic activity compared with other samples. The prepared samples were characterized by using various techniques such as X-ray diffraction, scanning electron microscopy, photoluminescence emission spectra, and UV–Vis diffuse reflectance spectroscopy.     

Synthesis,characterization and photocatalytic properties of tungsten-doped hydrothermal TiO<Subscript>2</Subscript>

Crystalline anatase phase TiO₂ with photocatalytic properties was obtained through a sol–gel low-temperature hydrothermal process. TiO₂ samples doped with tungsten oxide were also obtained by using this synthetic approach. The photocatalytic oxidation of methylene blue in water was monitored to study the influence of the tungsten doping degree on the photocatalytic degradation performance of TiO₂. The degradation rate constant was further increased by adjusting the tungsten doping degree of hydrothermal TiO₂. Also, a much faster photodegradation of methylene blue was achieved using tungsten doped samples baked at 450°C. The results were compared with those obtained with Degussa P25 used as photocatalyst. The structure and optical properties of tungsten-doped TiO₂ were studied by SEM, X-ray diffraction, UV–vis and DRIFT spectroscopy techniques.     

SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> nanoparticles in Aerosol OT reverse microemulsions: Synthesis and characterization

Stable SiO₂ and TiO₂ organosols were prepared by hydrolyzing tetraethyl orthosilicate (TEOS) in the presence of 6–12 M NH₃ and titanium(IV) isopropylate (TTIP) in reverse microemulsions of 0.12–0.25 M bis(2-ethylhexyl) sulfosuccinate (Aerosol OT, AOT) in n-decane with the aqueous pseudophase content of 2–3 vol %, 0.018–0.090 M TEOS, and 0.15–0.55 vol %, 0.003–0.025 M TTIP. The degree of hydrolysis was monitored by IR spectroscopy (for TEOS) and spectrophotometry (for TTIP). Oxide nanoparticles were characterized by photon-correlation spectroscopy (PCS) (D _h = 8–100 nm) and laser electrophoresis (ζ-potential = 7.4–11.6 mV). The occurrence of surface potential made it possible to separate the oxides from the excess of surfactant by nonaqueous electrophoresis and to determine particle sizes (7–40 nm) by means of transmission electron microscopy (TEM).     

Synthesis and characterization of TiO<Subscript>2</Subscript>-montmorillonite nanocomposites and their photocatalytic activity

TiO₂ nanoparticles have been synthesized on the surface of exfoliated montmorillonite at a low temperature in benzyl alcohol medium. According to X-ray diffraction (XRD), N₂ adsorption-desorption isotherm and transmisson electron microscopy (TEM), it was found that the intercalation of TiO₂ nanoparticles destroyed the ordered structure of montmorillonite to some extent, and the crystallites of the nanocomposites are assembled to form a house-of-cards structure. The size of the nanoparticles in the interlamellar space is about 4 nm. The nanocomposites exhibited excellent photocatalytic activity in methylene blue degradation due to the synergetic effect of the adsorptive ability to organic compound of cetyl trimethylammonium bromide—montmorillonite and the catalytic ability of TiO₂ nanoparticles in it.     

Synthesis and characterization of a new hybrid TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> filler for lithium conducting gel electrolytes

This paper describes the synthesis and properties of a new type of ceramic fillers for composite polymer gel electrolytes. Hybrid TiO₂-SiO₂ ceramic powders have been obtained by co-precipitation from titanium(IV) sulfate solution using sodium silicate as the precipitating agent. The resulting submicron-size powders have been applied as fillers for composite polymer gel electrolytes for Li-ion batteries based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF/HFP) copolymeric membranes. The powders, dry membranes and gel electrolytes have been examined structurally and electrochemically, showing favorable properties in terms of electrolyte uptake and electrochemical characteristics in Li-ion cells.     

TiO<Subscript>2</Subscript> nanofibers embedding single crystalline TiO<Subscript>2</Subscript> nanowires

Epitaxially grown titanium dioxide (TiO₂) nanofibers embedding single crystalline TiO₂ nanowires (NWs) were successfully fabricated by electropinning poly(vinyl pyrrolidone)/ethanol solutions mixed with hydrothermally synthesized TiO₂ NWs and titanium isopropoxide precursors and subsequently calcinating the electrospun nanofibers. Utilizing scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the morphologies of TiO₂ NWs and nanofibers were investigated. High resolution TEM (HR-TEM) and selected area electron diffraction (SAED) allowed us to indentify the fact that, during the calcination process under the optimized condition, titanium isopropoxide precursors were epitaxially crystallized on the surface of single crystalline TiO₂ NWs. Based on the X-ray diffraction (XRD) experiments, it was also realized that the crystalline structure of hydrothermally synthesized TiO₂ NWs and epitaxially crystallized TiO₂ nanofibers is anatase and that TiO₂ composite nanofibers embedding TiO₂ NWs exhibited a higher crystallinity than the pristine TiO₂ nanofibers. Additionally, ultraviolet visible (UV–Vis) spectra of nanofibers indicated that optical properties of TiO₂ nanofibers can be tuned by introducing the single crystalline TiO₂ NWs.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Chitosan-modified TiO<Subscript>2</Subscript> as photocatalyst for ethanol reforming under visible light

This work reports the reforming of bio-ethanol on chitosan–TiO₂ hybrid photocatalysts at ambient temperature. The influence of chitosan composition on the photocatalytic performance of chitosan–TiO₂ hybrid was studied. The hybrids were characterized by CHN elemental analysis, nitrogen adsorption–desorption isotherms, thermogravimetric analysis, diffuse reflectance spectroscopy, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results showed that the preparation variables used for the incorporation of chitosan on TiO₂ promoted changes in the morphology, superficial area, crystal size and porosity of the photocatalyst, affecting the band gap of this semiconductor and consequently the reactivity of the chitosan–TiO₂ hybrids. The catalysts were evaluated for hydrogen production from ethanol under visible light. It was demonstrated that the calcination temperature of 623 K and a chitosan content of 20% were the most appropriate preparation conditions and the resulting product displays a pore size of 1.9 nm, crystal size of 11.3 nm, BET area of 178 m² g^?1 and band gap of 2.92 eV. The calcination temperature of 623 K and incorporation of 20% of chitosan obtained the same results in the conversion rate of hydrogen in comparison to the pure TiO₂ P25.     

Synthesis of TiO<Subscript>2</Subscript> nano powder by the sol-gel method and its use as a photocatalyst

In this work the titanium dioxide powder was prepared by the optimized and simple Sol-Gel method and then characterized. The gelling pH was set to values of 3 (TiO₂-A), 7 (TiO₂-N) and 9 (TiO₂-B) to observe the effect on the properties of the material. In these three cases nanoparticulated materials were obtained with particle sizes between 10nm and 20nm. The larger surface areas were obtained at pH 3, which is several times larger than the others. Furthermore, with the gelling condition pH 3, it was possible to synthesize pure anatase phase titania. Some preliminary results on the test of the photocatalytic activity of the synthesized materials in the reduction of nitric oxide are presented. Based on these results the nanoparticle TiO2, which was prepared in acidic pH 3 with the pure anatase phase and the lowest particle size has the highest reactivity for the photocatalytic reduction of nitric oxide.     

Diagnostics of Plasma Behavior and TiO<Subscript>2</Subscript> Properties Based on DBD/TiO<Subscript>2</Subscript> Hybrid System

Plasma catalysis is gaining increasing interest in environmental and energy applications, such as the destruction of gas pollutants and hydrocarbon conversion. In order to further improve the application of plasma catalysis, it is crucial to understand the fundamental mechanisms, especially the mutual interaction between plasma and catalyst. In this paper, a parallel-plate dielectric barrier discharge (DBD) reactor is developed to investigate the plasma behavior and TiO₂ properties in the plasma/catalytic hybrid system. The introduction of TiO₂ thin film coated on the dielectric improves the discharge intensity, which significantly contributes to the enhancement of reactive species and charges. The energy efficiency of generating ozone in DBD/TiO₂ system has been approximately raised by 38% compared to pure DBD when the applied voltage reaches 13 kV. It is fortunately found that the discharge does not change the crystal structure of the TiO₂, but the band gap increases from 3.13 to 3.39 eV, which has been proved to enhance the oxidizability of TiO₂ in the degradation of methyl orange experiment under UV light. The FTIR and XPS spectra also demonstrate that N element is doped into the structure of TiO₂. These results successfully illustrate the plasma behavior and catalyst properties in plasma/catalysis hybrid system and provide reference for the optimization of the plasma catalysis process.     

Cooperation among N,F and Fe in tri-doped TiO<Subscript>2</Subscript> photocatalyst

TiO₂ photocatalysts tri-doped with N, F and Fe were synthesized by a sol–gel method. The cooperation of N, F and Fe in tri-doped TiO₂ was verified by monitoring NH₃ decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and by the simulation based on the density functional theory (DFT). The results from NH₃ decomposition revealed that the cooperation of N, F and Fe broadened the optical response of TiO₂ to the visible light range and also enhanced the photocatalytic activity of TiO₂ under UV light. The reusability of the tri-doped TiO₂ sample after three cycles under UV and visible light irradiation was very good. XRD patterns and SEM and HRTEM images indicated that the tri-doped sample was nanometric anatase with a small amount of rutile with an average particle size of 18 nm. Tri-doping with N, F and Fe suppressed the phase transition from anatase to rutile and also resulted in some more lattice defects. XPS analysis showed that the N, F and Fe atoms were doped into the TiO₂ lattice. UV–Vis absorption spectra of the tri-doped TiO₂ showed that its optical absorption edge was moved up to 640 nm and its UV absorption was also enhanced. The DFT results confirmed that the cooperation of Fe 3d and N 2p orbits narrowed the band gap of TiO₂ and the F 2p orbit broadened the upper valence bands. The synergistic electron density around N, F and Fe in tri-doped TiO₂ was capable of enhancing the photochemical stability and reusability of TiO₂.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Preparation of highly active photocatalyst anatase TiO<Subscript>2</Subscript> by mixed template method

TiO₂ nanocrystals with diameters 8–10 nm have been prepared through sol–gel method using a mixed template of polyethylene glycol (PEG) and cetytrimethylammonium bromide (CTAB) at low temperature. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution (HR) TEM and fourier transform infrared spectroscopy (FT-IR) etc. XRD analysis showed the TiO₂ photocatalysts prepared with mixed template are pure anatase. FTIR spectrum revealed that the cationic surfactant provides CTA⁺ molecules and bonds to Ti–O to prevent the condensation reaction. PEG plays a dispersant role in controlling the structure of nano-TiO₂ particles. CTAB and PEG incorporated with each other to restrain the growth of crystal nucleus and control the size of grain. The self-assembling process has been confirmed by HRTEM. PEG played different role in mixed template from the single template. The photocatalytic activity of samples was determined by using as a model reaction. The results showed that TiO₂ photocatalysts with mixed template have higher photocatalytic activity than P25.     

Photooxidation of Ethylbenzene with TiO<Subscript>2</Subscript> and Metal Coated TiO<Subscript>2</Subscript> and its Kinetics

Summary. Photooxidation of ethylbenzene with oxygen to give ethylbenzene hydroperoxide has been achieved in a stirred photochemical reactor that was cooled by a water system by irradiation with a 400W high-pressure mercury lamp and using TiO₂ powder and metal coated TiO₂. The effects of the amount of copper or silver coated on TiO₂ and of the temperature on the rate of oxidation have been investigated. It is suggested that thermal cleavage of the O–O bond and photochemically generated singlet oxygen should be considered as the initiating step in a radical chain mechanism. An optimum loading of 6% Ag or 4–5% Cu was observed for photooxidation of ethylbenzene.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Fabrication,characterization, and photocatalytic performance of TiO<Subscript>2</Subscript> hybridized with SiO<Subscript>2</Subscript>

Nanostructures TiO₂–SiO₂ photocatalysts were successfully synthesized using the sol-gel method, hydro-calcination, co-precipitation and room-temperature solid-phase synthesis technology. X-ray powder diffraction pattern (XRD), Fourier transform infrared spectrum (FTIR), photoluminescence (PL) spectra, thermal analyses (TG–DTA), scanning electron micrographs (SEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS) were used to characterize the as-synthesized catalysts. Photocatalytic performances of the catalysts were evaluated by the degradation of methyl orange (MO) under s imulated natural light and the degradation rate of MO is 97.2%. The composites showed a good stability: after five recycling runs there are no significant decreases in the photocatalytic activity. The photodegradation of methylene blue, rhodamine B, methyl violet, naphthol green B, basic fuchsin, malachite green, and methyl red were also tested, and the degradation rate of dyes could reach over 94.2 %. A possible mechanism for the photocatalysis with the TiO₂–SiO₂ was proposed.