A New Criterion for Brittle-Ductile Transition of Polymer Blends

The T_c criterion was first used by S. Wu for characterizing the brittleductile (B-D) transition of N6/EPDM blends. But in this paper, a new criterion which is based on the stress analysis of blends is proposed to characterize the B-D transitions of blends, namely, A criterionV_(fc) and d_c are the critical volume fractions and particle size of dispersed particles in blends, respectively. For given blends, A is independent of the morphology of dispersed phase and is only the characteristic parameter of matrix. The B-D transitions of different blends, including polar N6/EPDM blends, nonpolar PP/EPDM blends and PE/CaCO_3 composites, were manipulated with A criterion and satisfactory results were obtained. In addition, a new master curve for the impact strength of PP/EPDM blends versus V_f~2/d was obtained. The results showed that A criterion is more suitable than T_c criterion for characterizing the B-D transition of blends.     

固相法氯化聚乙烯对PVC／LLDPE共混体系性能和形态的影响

采用固相法氯化聚乙烯（ＣＰＥ）对聚氯乙烯／线型低密度聚乙烯（ＰＶＣ／ＬＬＤＰＥ）共混体系进行增容改性。扫描电子显微镜、透射电子显微镜、动态力学分析和力学性能测试结果表明，ＣＰＥ对ＰＶＣ／ＬＬＤＰＥ共混体系具有很好的增容作用。     

Effective interaction parameter of linear/star polymer blends and comparison with that of linear/linear and star/star blends

The authors present a detailed study of the microscopic parameters, which control the miscibility in binary linear/star polymer blends. The effective interactions of linear/star polymer blends are studied by means of Monte Carlo simulations and comparison is made with linear/linear and star/star blends, which they also determined. Using the bond fluctuation model on a simple cubic lattice, the authors are able to simulate symmetric linear/linear, star/star, and, for the first time, linear/star blends with a moderate number of arms. The simulations were performed at a volume fraction of occupied lattice sites phi=0.5, which corresponds to dense polymer mixtures for this algorithm. In particular, we study star/star blends with 4, 8, and 12 arms and the respective linear/linear blends as well as linear/star blends, all having the same total number of units equal to 73 and 121. The authors find that linear/star blends are more miscible than the corresponding linear/linear blends, which is in agreement with recent experimental and theoretical results. They find that linear/star mixtures are less miscible than star/star blends, a result which is also verified by theoretical findings.     

Influence of microstructure and deformation behavior on toughening of reactively compatibilized polyamide 6 and poly(ethylene-co-butyl acrylate) blends

Influence of microstructure on impact toughness and fracture behavior of PA6 and EBA blends reactively compatibilized by EBA-g-MAH was quantitatively studied. The reactively compatibilized blends showed better distribution of elastomeric EBA particles in the PA6 matrix and the presence of EBA-g-MAH resulted in considerable reduction of interfacial tension between the component polymers. The interfacial adhesion between the PA6 and EBA phase in the compatibilized blends was enhanced by the interfacial reaction between the amide end-groups of PA6 and maleic anhydride group of EBA-g-MAH compared to uncompatibilized blends. The matrix ligament thickness and particle diameter values were lower than the predicted critical values and were responsible for the ductile behavior of the compatibilized blends. Stress whitening around the notch occurred in all the compatibilized blends which was the major energy dissipation zone in the blends. Matrix shear yielding or plastic flow without crazing was the dominant deformation mechanism in the tough compatibilized blends. There was no sign of shear yielding during impact fracture of the uncompatibilized blends where the elastomeric particles were completely dislodged from the matrix.     

增容剂SB对LDPE/PS共混物形态的影响

研究了不同温度和转速下苯乙烯 -丁二烯二嵌段共聚物 (SB)低密度聚乙烯 聚苯乙烯共混物形态和分散相颗粒尺寸的影响。结果表明 ,未加入SB的共混物在 1 50℃时的分散相颗粒尺寸比 2 0 0℃粗大 ,形态极不规则 :加入SB的共混物在 1 50℃时颗粒尺寸比 2 0 0℃时稍小 ,但形态变化不大。在 1 50℃ ,转速从 3 0r min至 1 0 0r min时 ,未加入SB的共混物的分散相颗粒尺寸迅速减小 ,而加入SB的共混物在 3 0r min时达到平衡颗粒尺寸 ,继续增加转速 ,形态和颗粒尺寸没有明显变化。     

环氧树脂/聚碳酸酯固化共混物的结构及性能

相结构;酯交换反应;力学性能;环氧树脂/聚碳酸酯固化共混物的结构及性能     

Effect of chain blockiness on the phase behavior of ethylene‐octene copolymer blends

New challenges and opportunities for polyolefin blends arise from the recent introduction of olefin block copolymers (OBCs). In this study, the effect of chain blockiness on the miscibility and phase behavior of ethylene‐octene (EO) copolymer blends was studied. Binary blends of two statistical copolymers (EO/EO blends) that differed in comonomer content were compared with blends of an EO with a blocky EO copolymer (EO/OBC blends). The blends were rapidly quenched to retain the phase morphology in the melt and the phase volumes were obtained by atomic force microscopy (AFM). Two EOs of molecular weight about 100 kg/mol were miscible if the difference in octene content was less than about 10 mol % and immiscible if the octene content difference was greater than about 13 mol %. The blocky nature of the OBCs reduced the miscibility and broadened the partial miscibility window of the EO/OBC blends compared with the EO/EO blends. The EO/OBC blends were miscible if the octene content difference was less than 7 mol % and immiscible above 13 mol % octene content difference. It was also found that the phase behavior of EO/OBC blends strongly depended on blend composition even for constituent polymers of about the same molecular weight. Significantly more demixing was observed in an OBC‐rich blend (EO/OBC 30/70 v/v) than in an OBC‐poor blend (EO/OBC 70/30 v/v). An interpretation based on extractable fractions of the OBC described the major features of the EO/OBC (30/70 v/v) blends. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1554–1572, 2009     

Mechanical and Rheological Behavior of Unvulcanized and Dynamically Vulcanized i-PP/EPDM Blends

The mechanical and rheological behavior of dynamically vulcanized PP/EPDM blends is examined and compared with those of unvulcanized blends. The effect of blend ratio and dynamic vulcanization of EPDM rubber on tensile properties and flow are investigated. The mechanical properties of the blends are strongly influenced by the blend ratio. With the increasing of EPDM content the value of yield stress in a solid state decreases with the elastomer volume fractions less than 0.45 for the unvulcanized blends. For the dynamically vulcanized blends the interval of EPDM content, at which the yield peak is seen, is rather limited below 0.25 elastomer volume fractions. It is shown that dynamic vulcanization changes the deformational behavior of PP/EPDM blends. The rheological properties of dynamically vulcanized blends depending on the ratio of the components may be similar to the properties of polymer composites containing the highly disperse structuring filler. The distinction between the rheological behavior of unvulcanized and dynamically vulcanized blends is related to differences of their structures and viscoelastic characteristics of unvulcanized and vulcanized EPDM phase.     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

环氧树脂在热塑性树脂改性中的应用

本文综述了国内外有关利用环氧树脂改性热塑性树脂共混体系研究的最新进展。着重阐述了环氧树脂在热塑性树脂之间的增容作用,如尼龙6(PA6)合金体系,改性聚苯乙烯塑料(ABS)合金体系,以及聚对苯二甲酸丙二醇酯(PTT)合金体系等。同时,介绍了利用环氧树脂的反应活性提高无机填料在聚合物中分散性研究的情况,如二氧化硅纳米粒子在聚醚砜(PES)中,以及滑石粉在聚丙烯(PP)中分散性的提高。最后,简介了环氧树脂改性热塑性树脂提高热塑性树脂物理机械性能方面的研究方向和成果并展望了环氧树脂在热塑性树脂改性研究中的前景。     

A Concise Review on the Physicochemical Properties of Biopolymer Blends Prepared in Ionic Liquids

An enhancement of environmental concern lately has improved the awareness of researchers in employing eco-friendly solvents for processing biopolymers. Recently, ionic liquids have been utilized to prepare biopolymer blends as they are non-volatile and recyclable. Biopolymers such as cellulose, chitin, chitosan, keratin, lignin, silk, starch, and zein are widely used for the preparation of biopolymer blends via dissolution in ionic liquids, followed by coagulation procedure. In this concise review, three types of ionic liquids based on imidazolium cations combined with different counter anions that are frequently utilized to prepare biopolymer blends are described. Moreover, three types of biopolymer blends that are prepared in ionic liquids were classified, specifically polysaccharide/polysaccharide blends, polysaccharide/polypeptide blends, and polysaccharide/bioplastic blends. The physicochemical properties of biopolymer blends prepared in different imidazolium-based ionic liquids are also concisely reviewed. This paper may assist the researchers in the polymer blend area and generate fresh ideas for future research.     

High temperature polymer blends: an overview of the literature

A review of work which has been performed on high temperature polymer blends is presented. The discussion is divided into miscible and immiscible blends. It is pointed out that one problem with miscible polymer blends is that of processing in the miscible state. In the case of immiscible blends, particularly ones containing liquid crystal polymers, the issue of adhesion of the two phases is discussed. Finally, the need for better theoretical models for predicting miscibility in polymer blends is highlighted.     

一种加成固化型热固性树脂PN-PAA固化过程和热稳定性研究

研究了炔丙基醚化酚醛树脂(PN)与聚芳基乙炔树脂(PAA)的反应性共混物(以下简称PN-PAA共混树脂)的相容性,并对共混树脂的固化过程和固化物的耐热性进行了表征.相态、DSC、SEM、TEM等测试结果均表明共混树脂及其固化物是完全相容的均相体系.凝胶时间、粘度、DSC等结果表明共混树脂固化工艺性优良,适合多种成型工艺(如RTM),显著改善了PAA树脂的固化工艺缺陷.DMA、TGA等分析表明共混树脂固化物具有很高的耐热性,可作为新型的防热复合材料和高温结构材料的基体.     

粘度法研究氯化聚丙烯和涂料树脂间的相容性

用稀溶液粘度法研究了氯化聚丙烯与石油树脂、丙烯酸树脂和醇酸树脂间的相容性,并用α判据对相容性结果进行判别。结果显示,石油树脂/氯化聚丙烯的共混体系是相容的;丙烯酸树脂/氯化聚丙烯的共混体系是不相容的。而醇酸树脂与氯化聚丙烯的相容性情况复杂,由二者的组成决定。当m(醇酸树脂)∶m(氯化聚丙烯)1∶1时,体系是相容的;当m(醇酸树脂)∶m(氯化聚丙烯)1∶1时,体系是不相容的。通过共溶剂法和涂膜宏观特性对上述体系的相容性进行测定,所得结果与α判据的结果相符合,印证了稀溶液粘度法研究溶液中高分子间的相互作用来预测涂料树脂的相容性具有一定可行性。     

Effect of acrylonitrile content of SAN on the bending morphology and its quantitative variation inside crystals of PCL/SAN blends confined in thin films

The effect of acrylonitrile content of SAN on the bending morphology of PCL/SAN blends was studied. The blends were prepared from solution with different compositions, and isothermally crystallized at a certain temperature. During crystallization at 45°C, the truncated lozenge-shaped morphology of the PCL crystals being modified to regular/inverted S- or C-shaped morphology for PCL/SAN blends with 9.5–25% AN in SAN. The bending curvature increases by lowering the crystallization temperature, and the growth rate of PCL decreases with SAN reflecting the miscible nature of the blends. For blends with 30% AN in SAN, mix morphologies with different crystal growth rates reflects the immiscible nature of the blends. Raman spectroscopy reveals at lower crystallization temperature, for miscible blends, a small amount of SAN is retained in the PCL crystal, with a regular increase in concentration from the midpoint to the edge of the crystal, whereas a homogeneous distribution of SAN is found in immiscible blends. Those distribution of SAN are completely absent at higher crystallization temperatures due to a higher crystallographic order of the PCL crystals.     

动态硫化EPDM／PP共混体系中PP相的结晶度及晶体结构的研究

研究了动态硫化ＥＰＤＭ／ＰＰ共混物中ＰＰ相的结晶度及晶体结构,同时讨论了制备工艺条件以共混物中ＰＰ相的结晶度和晶体结构的影响。结果表明：在动态硫化ＥＰＤＭ／ＰＰ共混物中,硫化的ＥＰＤＭ的分子键没有穿入ＰＰ的晶区,ＰＰ的结晶度随ＥＰＤＭ含量的增加而下降。提高共混温度,加入软化剂或碳黑均使共混物中ＰＰ的结晶度降低,共混时间１５ｍｉｎ时,共混物中ＰＰ相的结晶度最低,但ＰＰ的晶格不受制备工艺条件的影响。     

聚乳酸共混体系的研究进展

聚乳酸是人工合成的可生物降解的热塑性脂肪族聚酯 ,是一种环境友好的材料 ,逐渐成为人们研究的热点。本文根据聚乳酸共混体系中另一组分的生物降解性 ,将聚乳酸共混体系分为完全可生物降解共混体系和部分可生物降解共混体系两类。针对体系的相容性和结晶结构以及在提高PLA的性能和降低成本等方面 .综述了聚乳酸共混体系的最新研究进展 ,并对其发展动态进行了简要介绍     

Nonisothermal crystallization behavior of isotactic polypropylene/ thermoplastic rubber blends

The morphology and crystallization behavior of blends of polypropylene (PP) and an ethylene-based thermoplastic elastomer (TPO) were investigated by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The SEM images showed a two-phase morphology for these blends. As TPO was partially crystalline, two distinct peaks were observed in both heating and cooling scans of DSC. The crystallization temperature of TPO in blends was higher than pure TPO. In contrast, the crystallization temperature of PP in blends was lower than pure PP. The crystallization behavior of blends was modeled by Avrami equation. It was observed that the presence of TPO accelerated the growth rate of crystals of PP in PP/TPO blends.     

Mechanical, morphological and biodegradation studies of microwave processed nanostructured blends of some bio-based oil epoxies with poly (vinyl alcohol)

Bioresource based blends exploit the synergy between polymers derived from renewable resource and commercial polymers to obtain desirable physical, mechanical, and biodegradable properties. With the aim to develop a sustainable resource based biodegradable mulch films, nanostructured blends of epoxies of linseed oil (LOE) and dehydrated castor oil (DCOE) with poly (vinyl alcohol) (PVA) were prepared in the weight ratios of 20/80, 50/50 and 80/20. Microwave-assisted blending was used for the synthesis of DCOE/LOE blends with PVA and the results were compared with conventional solution blending using FT-IR, TGA-DTA and optical measurements. The results revealed that microwave-assisted blending proved to be an efficient method for the formation of compatible blends in a short span of time as compared to conventional solution blending. Transmission electron microscopy (TEM) analysis of DCOE/PVA and LOE/PVA blends synthesized by microwave-assisted method confirmed the formation of a nanostructured blend. Scanning electron microscopy (SEM), respirometry and mechanical measurements were carried out to compare the morphology, biodegradability, and the mechanical strength of DCOE/PVA and LOE/PVA blends. It was observed that DCOE/PVA blends exhibited higher biodegradability, better mechanical properties, and lower moisture absorption characteristics as compared to LOE/PVA blends. The mechanical strength, moisture absorption, and biodegradability of these blends were also compared with blends of other bioresource based polymers such as sugarcane bagasse (SCB), waste gelation (WG), apple peal (AP), and starch/glycerol with PVA, as available from the cited literature in the text.     

PVC／PE交联共混体系的动态力学研究

在ＰＶＣ／ＰＥ共混体系中加入交联剂和引发剂能产生ＰＶＣ－ＣＯ－ＰＥ共聚物，这种共聚物在共混物中可起到增容剂的作用。通过动态力学分析和扫描电镜研究了ＰＶＣ／ＰＥ交联共混体系的相容性。发现引发剂、交联剂、稳定剂和增塑剂等对共混物中的交联反应均有较大的影响。