Fabrication of Pt nanoparticles-decorated CVD diamond electrode for biosensor applications

An electrochemical biosensor was developed using boron-doped diamond (BDD) as an electrode material. To enhance the electrical performance of the electrode, the BDD electrode was decorated with Pt-nanoparticles (Pt-NPs) by electrochemical deposition. Their morphology according to the applied potentials for the synthesis of Pt-NPs was characterized by SEM. To identify the performance of the electrode modified with Pt-NPs, glucose detection was used as a sample sensing process, and the results were compared with those of a gold electrode and a bare BDD electrode. The electrochemical characteristics of the modified electrode were examined by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The BDD electrode with the Pt-NPs showed higher sensitivity and a lower detection limit than the Au electrode and BDD electrode. The proposed biosensor based on the Pt-NPs decorated BDD electrode showed high sensitivity, a low detection limit, fast direct electron transfer and good stability.     

Electrocatalysis by ad-atoms: Part IV. Enhancement of the oxidation of formic acid on Pt-Au(subs) and Au-Pt(subs) electrodes by bismuth ad-atoms

The roles of surface and bulk for electrocatalysis have been investigated. Bi ad-atoms enhance a platinum electrode to a great extent for HCOOH oxidation. In order to examine whether bulk platinum atoms are necessary for the electrocatalysis, monolayer or submonolayer amounts of platinum atoms were made to deposit on a gold electrode which is quite inactive for the oxidation. The deposition of a complete monolayer of platinum atoms on a gold electrode makes the electrode as active as a platinum electrode itself. Bi ad-atoms enhance this electrode to the same extent as they do a platinum electrode for the oxidation. Thus surface atoms, Pt and Bi atoms, having no bulk atoms on a quite inactive electrode work effectively for the electrocatalysis, the platinum atoms for the adsorption of the main reactant and the Bi atoms for blocking of the sites against the formation of poison. It is the adsorptive property of the surface that controls the electrocatalytic activity.     

Chloride Response of a Cadmium Chloride Electrode

An unsymmetrical quaternary ammonium salt, trinonyloctadecylammonium tetrachlorocadmiate, was used for the preparation of a chloride-selective electrode. The electrode parameters were examined. An equation for the semiquantitative estimation of the electrode response was proposed. The electrode was used for determining chloride ions in blood serum.     

Studies of copper(II) sulphide ion-selective electrodes

Changes in liquid junction potentials in copper(II) solutions were measured when different reference electrodes were used. The slope and intercept of a calibration curve for a copper-selective electrode will depend on the selection of reference electrode. The condition of the electrode surface of an Orion copper-selective electrode was studied microscopically and the influence of redox potential on stability of the electrode against corrosion is discussed. Oxidizing solutions will produce pits at dislocations in the material and there will be a mixed electrode potential. The slope, stability, and speed of response are much lower when the surface contains pits. Diamond-polishing was shown to improve the electrode significantly.     

The determination of copper,lead and cadmium in sea water by differential pulse anodic stripping voltammetry

The effect of various instrumental parameters is investigated and optimized conditions established. The results are in accordance with the theory of differential pulse anodic stripping voltammetry. Both a hanging mercury drop electrode, and a rotating glassy carbon electrode mercury plated in situ were used. The best detection limit is obtained with the mercury film electrode, but the hanging mercury drop electrode is more reproducible. The differential pulse stripping technique is compared to linear sweep stripping, and increased sensitivity and better peak separation is demonstrated for the former technique, particularly when a hanging mercury drop electrode is used. However, the differential pulse technique will also improve the detection limit for a mercury film electrode, if the electrode has a non-ideal response with a corresponding high background current.     

Evaluation of the oxygen reduction activities of rare-earth oxide-supported silver catalysts using a channel flow double electrode.

The channel flow double electrode (CFDE) was used for the evaluation of the oxygen reduction activities in alkaline solution of rare-earth oxide-supported silver catalysts. The CFDE cell was modified for the experiment using the powder catalyst as a working electrode. In the present experiment, the silver electrode was supported with CeO2 in order to improve the performance of the oxygen reduction. The detecting electrode current for HO2- emitted from the working electrode was recorded simultaneously with the measurement of the i-E curve of each working electrode. Moreover, the average number of charge transfers n was calculated from the working and detecting electrode currents. The value of n for the oxygen reduction was approximately 4 for silver electrode supported with rare-earth oxide, compared with the n value of pure silver that was smaller than 4. On the basis of these results, the mechanisms of oxygen reduction on these electrodes and role of the rare-earth oxide in alkaline solution were discussed.     

Potentiometric Determination of Acids and Bases using Silicone Rubber Based Graphite Electrode

Abstract

A silicone rubber based graphite electrode has been used as an indicator electrode for potentiometric acid-base titrations. The electrode potential changes an average of 30 mV per pH-unit. If the electrodes are pretreated with a solution of an oxidant before use, the pH-sensitivity is increased. The electrode can be used in both aqueous and non-aqueous solutions. A measuring cell, composed of a silicone rubber based graphite electrode of small surface area and a chloride-selective reference electrode, can be used for acid-base titrations in the micro range.     

化学修饰电极的研究XVIII,四苯基钴卟啉化学修饰玻碳电极的热处理及其对氧的催化还原

本文研究四苯基钴卟啉化学修饰玻碳电极的热处理,经热处理的这种电极[(PCo/GC)h]具有对氧催化还原的异常高的稳定性和活性.在纯O2饱和的0.05mol.L^-^1H2SO4溶液中经循环伏安(CV)扫描3000次(100mV/s),其催化活性未见明显降低.研究了热处理温度(500-1000℃)对(PCo/GC)h电极电催化性能的影响.用紫外可见光谱对热处理产物的结构进行了分析.用CV法及旋转圆盘电极研究了O2在(PCo/GC)h电极上电催化反应动力学,测定了速率常数.在该电极上O2的还原反应为二电子还原成H2O2的不可逆过程.     

Fe修饰多壁碳纳米管电极高效产H2O2

为提高电芬顿(Electro-Fenton)体系H2O2的产率, 制备了多壁碳纳米管(MWNT)电极, 并与石墨/气体扩散(GDC)电极进行了比较. 结果表明, MWNT电极H2O2产率高于GDC电极. 采用电沉积方法, 制备了Fe修饰MWNT(Fe-MWNT)电极, 发现Fe对MWNT电极的修饰不仅可以提高体系的H2O2产率, 而且电流效率可以提高8%左右, 与GDC电极的电流效率接近. Fe-MWNT电极有望成为一种新型的阴极材料应用于Electro-Fenton体系中.     

Design of a new dodecyl sulfate-selective electrode based on conductive polyaniline.

A new, simple, sensitive, low cost and rapid potentiometric method for direct determination of ultra trace amounts of sodium dodecyl sulfate (SDS) with a new DS(-)-selective electrode is reported. The electrode was prepared by electropolymerization of aniline in acidified DS- ion on the surface of a Pt electrode. The cyclic voltammetry (CV) was used for electropolymerization of polyaniline (PA) in the potential range of -200 to +1000 mV vs. Ag/AgCl. This sensor showed a Nernstian behavior (59.0 +/- 2.3 mV/decade) over a very wide linear range (1.0 x 10(-9)-3.0 x 10(-6) M) with a detection limit of 1.0 x 10(-9) M. The response time of the electrode was 15 s for 1.0 x 10(-7) M of analyte; the electrode can be used for 4 weeks without any major deviation. This electrode can be used in the pH range of 3.5-9.8. The selectivity of electrode to DS- over some organic, inorganic and anionic surfactants was investigated with the fixed primary ion method. The results show that the electrode is highly selective to DS- ion over other ions. The proposed electrode was applied to the determination of DS- in real samples.     

血红素LB膜的电化学行为

采用循环伏安法研究了血红素与脑磷脂混合Y型LB（Langmuir-Blodgett）膜在玻碳电极上的电化学行为，结果表明血红素LB膜有良好的电化学活性，在0．1mol/L KCl溶液中有一对氧化还原峰（－0．42V／－0．30V）；将血红素LB膜转移到玻碳电极表面得到的血红素LB膜修饰电极（heme LB-GC）对溶液中溶解氧的电化学还原有良好的催化作用，其催化还原过程具有不可逆电荷传递特性。     

同时测定多巴胺和肾上腺素的大环镍膜修饰电极

研究了大环镍膜修饰电极对多巴胺和肾上腺素的电化学响应特性；结果表明，该修饰电极对多巴胺和肾上腺素的电极反应具有良好的催化活性，多巴胺和肾上腺素在修饰电极上的氧化电位比在裸铂电极上分别负移了230mV和70mV，使二者的阳极峰得到很好的分离，且灵敏度大为提高；将该修饰电极用于多巴胺和肾上腺素的同时检测，获得满意结果，生物体中的主要干扰物质抗坏血酸和NO2^-等均不干扰测定。     

Catalysis of dioxygen reduction at soluble polyaniline modified electrode

A reflux-treatment of soluble polyaniline (SPA) in dimethylformamide (DMF) containing CoCl₂ yields an active catalyst for dioxygen reduction which can be adsorbed on the electrode surface firmly. The catalytic reduction of dioxygen at the glassy carbon (GC) electrode modified by the catalyst was studied with cyclic voltammetry (CV), rotating disk electrode (RDE) and rotating ring-disk electrode (RRDE). The kinetic process of dioxygen reduction at the modified electrode was analyzed with a new RRDE theory dealing with a nondiffusion-controlled process on ring electrode. The rate constants for each scheme of dioxygen reduction were calculated, showing that only 2-electron reduction to H₂O₂ was conducted at the modified electrode. The effect of solution acidity on the electrocatalytic behaviour for dioxygen reduction was investigated. A possibility of initiating catalytic activity for dioxygen reduction was explored with ESCA method.     

Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

Determination of trace amounts of lead and cadmium using a bismuth/glassy carbon composite electrode

We examined the use of a bismuth-glassy carbon (Bi/C) composite electrode for the determination of trace amounts of lead and cadmium. Incorporated bismuth powder in the composite electrode was electrochemically dissolved in 0.1 M acetate buffer (pH 4.5) where nanosized bismuth particles were deposited on the glassy carbon at the reduction potential. The anodic stripping voltammetry on the Bi/C composite electrode exhibited well-defined, sharp and undistorted peaks with a favorable resolution for lead and cadmium. Comparing a non-oxidized Bi/C composite electrode with an in-situ plated bismuth film electrode, the Bi/C composite electrode exhibited superior performance due to its much larger surface area. The limit of detection was 0.41 μg/L for lead and 0.49 μg/L for cadmium. Based on this study, we are able to conclude that various types of composite electrodes for electroanalytical applications can be developed with a prudent combination of electrode materials.     

双盘工作电极参比电位采样快扫伏安方法

报道一种双铂盘工作电极、相应的毛细管参比电极和竖直式电化学池设计并用于快速循环伏安测量.双工作电极包括一个常规工作电极,一个辅助工作电极.后者在使用中接地,仅提供参比电位来控制工作电极的电位.参比毛细管尖端安设在接近辅助工作电极的位置上;用0.3mm直径Pt盘工作电极,在电位扫描速度高达10kV/s都可以得到类似于100%iR补偿的伏安曲线,而不必使用iR补偿电路.本文围绕高扫速伏安法中工作电极电位的准确控制问题做了一些初步的探讨.     

High-throughput dielectrophoretic manipulation of bioparticles within fluids through biocompatible three-dimensional microelectrode array

Dielectrophoresis (DEP) has been deemed as a potential and ideal solution for bioparticle manipulation. A 3-D carbon micro-electro-mechanical system (MEMS) fabricated from the latest developed carbon-MEMS approach has advantages of offering low-cost, biocompatible and high-throughput DEP manipulation for bioparticles. In this paper, a typical process for fabrication of various 3-D microelectrode configurations was demonstrated; accurate numerical analysis was presented on electric field gradient distribution and DEP force based on various microelectrode array configurations. The effects of electrode edge angle, electrode edge-to-edge spacing and electrode height on the electric field distributions were investigated, and optimal design considerations and rules were concluded through analysis of results. The outcomes demonstrate that the sharp edge electrode is more effective in DEP manipulation and both electrode edge-to-edge spacing and electrode height are critical design parameters for seeking optimal DEP manipulation. The gradient magnitude increases exponentially as the electrode spacing is reduced and the electric field extends significantly as the electrode height increases, both of which contribute to a higher throughput for DEP manipulation. These findings are consistent with experimental observations in the literature and will provide critical guidelines for optimal design of DEP devices with 3-D carbon-MEMS.     

纳米碳管电极上氧的电催化还原

以聚四氟乙烯为粘结剂制成了多壁纳米碳管（MWNT）电极.采用恒电位阶跃法和循环伏安法研究了MWNT电极在碱性溶液中的电化学行为，并对碱性溶液中溶解氧在该电极上的电化学还原行为进行了研究.实验结果表明： MWNT电极具有比石墨电极更高的孔隙率和电化学表面积；MWNT电极上O2还原成的反应为准可逆过程；在5～50 mV•s－1的扫描速率范围内，阴极峰电流与扫描速度成线性关系，表明MWNT电极上O2还原成的反应受吸附控制；对碱性溶液中的氧还原反应， MWNT比石墨具有更高的催化活性.     

钙钛矿型氧化物电极极化过程中的导电特性

研究了La_(0.5)Sr_(0.5)CoO_3等钙钛矿型氧化物电极的极化性质及它们对氧电化学还原的催化活性。发现在阴极极化过程中氧化物电极发生还原时,其电催化活性降低,电极阻抗明显增加,而在阳极极化过程中电极阻抗减小。讨论了影响钙钛矿型氧化物导电的因素及电极阻抗变化对电极性能的影响。     

Sheath-flow electrochemical detection of amino acids with a copper wire electrode in capillary electrophoresis

Here, we report the detection of native amino acids using a sheath-flow electrochemical detector with a working electrode made of copper wire. A separation capillary that was inserted into a platinum tube in the detector acted as a grounded electrode for electrophoresis and as a flow channel for sheath liquid. Sheath liquid flowed outside the capillary to support the transport of the separated analytes to the working electrode for electrochemical detection. The copper wire electrode was aligned at the outlet of the capillary in a wall-jet configuration. Amino acids injected into the capillary were separated following elution from the end of the capillary and detection by the copper electrode. Three kinds of copper electrodes with different diameters-50, 125, and 300 μm-were examined to investigate the effect of the electrode diameter on sensitivity. The peak widths of the analytes were independent of the diameter of the working electrode, while the 300-μm electrode led to a decrease in the signal-to-noise ratio compared with the 50- and 125-μm electrodes, which showed no significant difference. The flow rate of the sheath liquid was also varied to optimize the detection conditions. The limits of detection for amino acids ranged from 4.4 to 27 μM under optimal conditions.