Magnetic pair making and breaking effect of Ru in La0.7Sr0.3Mn0.9Ru0.1O3 and La0.5Sr0.5Co0.9Ru0.1O3

The substitutional effect of Ru on the magnetic and transport properties of double exchange ferromagnets, La_0.7Sr_0.3MnO₃ and La_0.5Sr_0.5CoO₃ has been investigated. It is found that substitution of 10% Ru at the Mn site of La_0.7Sr_0.3MnO₃ decreases the Curie temperature by 20 K than that of the parent compound. However, a large decrease in the Curie temperature, ΔT_c80 K and the system undergoes a transition from metallic state to insulating state is observed when 10% Ru is doped in La_0.5Sr_0.5CoO₃. The marginal effect of Ru in the Mn–O–Mn sublattice in comparison to the Co–O–Co sublattice could be due to the magnetic exchange interaction between Mn and Ru by virtue of the fact that Ru exhibits variable valence states, Ru⁺⁴/Ru⁺⁵. The e_g and t_2g parentage of Ru⁺⁵ is similar to Mn⁺⁴ and therefore, Ru⁺⁵ ion appears to participate in the double exchange mediated ferromagnetic (FM) interaction. On the other hand, Ruthenium (IV) ion disrupts an intermediate spin state of cobalt (Co⁺³: t_2g⁵e_g¹), forcing a double exchange FM state to anti-FM state.     

Effect of Co substitution on magnetic properties of Sr14Cu24O41

A series samples of Sr₁₄(Cu_1−xCo_x)₂₄O₄₁ (x=0, 0.02, 0.06, 0.14, 0.18) were prepared by standard solid-state reaction. X-ray diffraction measurements show that all the samples are single phase and their lattice parameter hardly changes by Co dopant. Electron diffraction experiments and X-ray photo-emission spectroscopy measurements reveal that Co ions substituted Cu ions in the chain. The measurements of magnetic susceptibility from 10 to 300 K in an applied magnetic field of 1.0 T show that Co dopant induces increase in susceptibility. The spin gaps are observed in all the samples, and decrease with increase in Co doping concentration. Fitting of the date indicates that strong antiferromagnetic interaction is induced and antiferromagnetic dimeried state may be formed due to Co³⁺ ions doping in these compounds.     

New red Y0.85Bi0.1Eu0.05V1−yMyO4 (M=Nb, P) phosphors for light-emitting diodes

The Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) as new near-ultraviolet excited phosphors were synthesized and their luminescence properties under 365 nm excitation were investigated in detail. It indicated that by doping small amount of P⁵⁺ into V⁵⁺ sites, the excitation intensity of charge transfer (CT) band of Bi–O (330–400 nm) was greatly improved. By substituting Nb⁵⁺ for V⁵⁺, both the CT bands of Bi–O and Eu–O (240–320 nm) were significantly enhanced. As a result, the emission intensity of Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) could be improved about 90% by doping 5 mol% P⁵⁺ and 110% by doping 5 mol% Nb⁵⁺. Comparing with the commercial Y₂O₂S:Eu³⁺ phosphors, the Y_0.85Bi_0.1Eu_0.05V_0.95M_0.05O₄ (M=Nb, P) phosphors exhibited excellent color purity and much higher brightness. The results showed that these Y_0.85Bi_0.1Eu_0.05V_1−yM_yO₄ (M=Nb, P) phosphors could be considered as promising red phosphors for application in LED.     

Direct measurement of the magnetocaloric effect in La0.67Ca0.33MnO3

Polycrystalline perovskite La_0.67Ca_0.33MnO₃ was synthesized by a sol–gel method. Its adiabatic temperature change ΔT_ad induced by a magnetic field change was measured directly. At 268 K, near its Curie temperature T_C, ΔT_ad of La_0.67Ca_0.33MnO₃ induced by a magnetic field change of 2.02 T reaches 2.4 K. The latent heat Q and magnetic entropy change −ΔS_M induced by a magnetic field change were calculated from the temperature dependence of ΔT_ad and zero-field heat capacity C_p. The maximum values of Q and −ΔS_M in La_0.67Ca_0.33MnO₃ induced by a magnetic field change of 2.02 T are 1.85 J g⁻¹ and 6.9 J kg⁻¹ K⁻¹, respectively. The former is larger than the phase transition latent heat of heating or cooling, which is about 1.70 J g⁻¹.     

High-temperature ferromagnetism in Zn1−xMnxO semiconductor thin films

Clear evidence of ferromagnetic behavior at temperatures >400 K as well as spin polarization of the charge carriers have been observed in Zn_1−xMn_xO thin films grown on Al₂O₃ and MgO substrates. The magnetic properties depended on the exact Mn concentration and the growth parameters. In well-characterized single-phase films, the magnetic moment is 4.8 μ_B/Mn at 350 K, the highest moment yet reported for any Mn doped magnetic semiconductor. Anomalous Hall effect shows that the charge carriers (electrons) are spin-polarized and participate in the observed ferromagnetic behavior.     

Magnetocaloric and magnetoresistance properties of La2/3Sr1/3Mn1−xCoxO3 compounds

Structural, magnetic, magnetoresistance and magnetocaloric studies on La_2/3Sr_1/3Mn_1−xCo_xO₃ compounds were reported. The samples were prepared by the conventional ceramic method. X-ray analysis showed the presence of one phase only, in all studied samples. From electrical resistance measurements it was found that the samples show large negative magnetoresistance behavior. The magnetic measurements were performed in a large temperature range, 4.2–750 K and external magnetic fields up to 5 T. The adiabatic magnetic entropy changes, |ΔS|, were determined from magnetization data. Large magnetocaloric effect (MCE) has been obtained in all studied samples.     

Structure and composition of secondary phase particles in cobalt-doped TiO2 films

The microstructural properties of secondary phase particles formed in epitaxial Co_xTi_1−xO₂ anatase thin films grown on (0 0 1)LaAlO₃ by a reactive RF magnetron co-sputter deposition are examined. These films exhibit ferromagnetic behavior in magnetization measurements, showing a M–H loop at room temperature with a saturation magnetization on the order of 0.7 μ_B /Co. X-ray photoemission spectrometry indicates that the Co cations are in the Co²⁺ valence state. Cross-section electron microscopy reveals that a significant fraction of the cobalt segregates into Co–Ti–O secondary phase particles. Selected area electron diffraction shows that the secondary phase particles are cobalt-rich anatase. While the cobalt is concentrated in the segregated particles, local energy dispersive spectrometry indicates some Co throughout the film.     

Magnetic properties of Lu2Co17−xSix single crystals

The Co-sublattice anisotropy in Lu₂Co₁₇ consists of four competitive contributions from Co atoms at crystallographically different sites in the Th₂Ni₁₇-type of crystal structure, which result in the appearance of a spontaneous spin-reorientation transition (SRT) from the easy plane to the easy axis at elevated temperatures. In order to investigate this SRT in detail and to study the influence of Si substitution for Co on the magnetic anisotropy, magnetization measurements were performed on single crystals of Lu₂Co_17−xSi_x (x=0−3.4) grown by the Czochralski method. The SRT in Lu₂Co₁₇ was found to consist of two second-order spin reorientations, “easy-plane”–“easy-cone” at T_SR1≈680 K and “easy-cone”–“easy-axis” at T_SR2≈730 K. Upon Si substitution for Co, both SRTs shift toward the lower temperatures in Lu₂Co₁₆Si (T_SR1≈75 K and T_SR2≈130 K) with the further onset of the uniaxial type of magnetic anisotropy in the whole range of magnetic ordering for Lu₂Co_17−xSi_x compounds with x>1 due to a weakening of the easy-plane contribution from the Co atoms at the 6g and 12k sites to the total anisotropy.     

Low-field negative magnetization and coercive-field magnetization reversal in transition metal chalcogenides; Cr2FeSe4 magnetic structure from neutron diffraction

Low-field negative magnetization, of the order of −10⁻¹ emu/g-Oe, from 4.2 K up to room temperature and higher (350 K), and coercive-field magnetization reversal are both present in Cr_(3−x)Fe_xX₄ for X=S, Se, Te and x=0 to 3, and for Cr₅Te₈ and Cr₇Te₈. For Cr₂FeSe₄ the zero-field-cooled (ZFC) magnetization is negative for 5 Oe and below. To obtain a more detailed knowledge of the magnetic phases involved in the observed magnetization versus temperature M(T) curves, we obtained and studied neutron diffraction (n.d.) scans on the compound Cr₂FeSe₄, taken at 14 temperatures from 4.2 to 300 K. For this same n.d. sample, the temperature for magnetization reversal of value −3×10⁻⁴ emu/g-Oe is 80 K in 40 Oe applied field, then the reversal disappears for 65 Oe applied field. The complex magnetic interactions responsible for this reversal are revealed in the hysteresis curves.     

Features of the electrochemical lithium insertion into monophosphate tungsten bronzes (PO2)4(WO3)2m (m=9 and 10)

Electrochemical lithium insertion into (PO₂)₄(WO₃)_2m, where m=9 and 10, has allowed the determination of several phases Li_x(PO₂)₄(WO₃)_2m between 3.4 and 0.01 V vs Li⁺/Li⁰. After the first cycle the electrochemical system was unable to maintain the high specific capacity of the cells (540 Ah/kg) due to irreversible processes. Nevertheless at high voltage values, above 1.4 V vs Li⁺/Li⁰, the lithium insertion proceeded through a reversible mechanism. By means of X-ray diffraction experiments we have detected the nature of different phases Li_x(PO₂)₄(WO₃)_2m formed and we have established a correlation with the reversible/irreversible processes detected during the electrochemical insertion.     

Phase formation and magnetic properties of Nd2Fe14B-type Nd16Co76B8−xCx alloys and their hydrides

An attempt is made to synthesize Nd₂Co₁₄C compound by mechanical alloying Nd₁₆Co₇₆B_8−xC_x (0x8) alloys and subsequent annealing. Phase formation and magnetic properties of Nd₂Fe₁₄B-type Nd₁₆Co₇₆B_8−xC_x alloys and their hydrides are investigated. The Nd₂Co₁₄(B,C) phase with Nd₂Fe₁₄B-type structure is formed for Nd₁₆Co₇₆B_8−xC_x (0x7) alloys, while NdCo₇C_δ phase with TbCu₇-type structure is observed in Nd₁₆Co₇₆C₈ alloy. The lattice parameter c of the Nd₂Co₁₄(B,C) phase decreases with increasing the carbon content. A limit volume of the unit cell to form the Nd₂Fe₁₄B-type structure is estimated to be 0.870 nm³. The spin-reorientation temperature T_SR increases with increasing the carbon content, due to an enhancement of magnetocrystalline anisotropy caused by carbon substitution for boron. After hydrogenation, the lattice expansion is observed for Nd₁₆Co₇₆B_8−xC_x (0x7) alloys. The spin-reorientation temperature of Nd₁₆Co₇₆B_8−xC_xH_y (0x7) is much lower than that of the host alloys. Some structural and magnetic properties of hypothetic Nd₂Co₁₄C and Nd₂Co₁₄CH_y compounds are estimated by extrapolation.     

W doping-dependent structural and ferroelectric properties of SrBi2Nb2O9 ferroelectric ceramics

The structural and ferroelectric characteristics of SrBi₂(Nb_1−xW_x)₂O₉ (x=0–0.12) ferroelectric ceramics were investigated. SrBi₂(Nb_1−xW_x)₂O₉ ceramics consisted of a single-phase layered perovskite structure when x was less than 0.06. Uniform microstructure and grain size reduction were observed after the introduction of W. The maximum remanent polarization of 16 μC/cm² appeared at x=0.03, and the coercive field decreased with increasing concentration of W. The ferroelectric behavior of SrBi₂(Nb_1−xW_x)₂O₉ ceramics is interpreted based on the Raman measurement.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

Structure determination, magnetic and optical properties of a new chromium(II) thioantimonate, [Cr((NH2CH2CH2)3N)]Sb4S7

The chromium(II) antimony(III) sulphide, [Cr((NH₂CH₂CH₂)₃N)]Sb₄S₇, was synthesised under solvothermal conditions from the reaction of Sb₂S₃, Cr and S dissolved in tris(2-aminoethyl)amine (tren) at 438 K. The products were characterised by single-crystal X-ray diffraction, elemental analysis, SQUID magnetometry and diffuse reflectance spectroscopy. The compound crystallises in the monoclinic space group P2₁/n with a=7.9756(7), b=10.5191(9), c=25.880(2) Å and β=90.864(5)°. Alternating SbS₃³⁻ trigonal pyramids and Sb₃S₆³⁻ semi-cubes generate Sb₄S₇²⁻ chains which are directly bonded to Cr(tren)²⁺ pendant units. The effective magnetic moment of 4.94(6)μ_B shows a negligible orbital contribution, in agreement with expectations for Cr(II):d⁴ in a ⁵A ground state. The measured band gap of 2.14(3) eV is consistent with a correlation between optical band gap and framework density that is established from analysis of a wide range of antimony sulphides.     

Ionic conductivity and phase stabilization in Cu- and Tl-substituted CsAg2I3

Samples of general formula CsAg_2−xM_xI₃, x=0–0.4 and M=Cu and Tl, have been prepared and studied by powder X-ray diffraction, DSC and electrical conductivity measurements. X-ray diffractograms and DSC curves showed the possibility of stabilizing the high-temperature -phase at lower temperatures in Tl-substituted samples, while such results were not obtained in Cu-substituted samples. Ionic conductivity measurements showed two regions corresponding to the low- and high-temperature phases. The transition temperature between the two phases was found to remain unchanged with the addition of Cu⁺ and decreased gradually with increasing Tl⁺. The ionic conductivity decreased in Cu-substituted samples and enhanced with the incorporation of Tl⁺ ion in the lattice of CsAg₂I₃. Dielectric constant was found to show behaviour similar to that of the ionic conductivity, and this is an evidence of the predominant effect of ion hopping on this property.     

Crystal structure, electrical and magnetic properties of La1 − xSrxCoO3 − y

The crystal structure and properties of La_{1 − x}Sr_xCoO_{3 − y} with strontium contents ranging from x = 0.1 to x = 0.7 have been studied. The lattice parameters were measured as a function of temperature (4.2–400 K) and the crystal structure was found to change from rhombohedral (at low temperatures and values of x) to cubic. While LaCoO₃ is paramagnetic the oxides in the composition range 0.2 < x < 0.6 are soft ferromagnets. The strontium additions are compensated by the formation of Co⁴⁺ (cobalt ions with one positive effective charge, Co_Co^.) and oxygen vacancies (V_o^..). From the results it is concluded that the relative importance of oxygen vacancies increases with increasing temperature and decreasing oxygen activity. As a result the concentration of electronic charge carriers — and the resultant electrical conductivity — decrease with increasing temperature. The defect structure is discussed and it is concluded that defect associations — probably between oxygen vacancies and strontium ions — and formation of microdomains of perovskite-related phases are important aspects of the overall structure of these perovskite phases.     

Investigation of the static and dynamic magnetic properties of CoFe2O4 nanoparticles

We have investigated the magnetic behavior of cobalt ferrite nanoparticles with a mean diameter of 7.2 nm. AC susceptibility of colloidal cobalt ferrite nanoparticles was measured as a function of temperature T from 2 to 300 K under zero external DC field for frequencies ranging from f=10 to 10,000 Hz. A prominent peak appears in both χ′ and χ″ as a function of T. The peak temperature T₂ of χ″ depends on f following the Vogel–Fulcher law. The particles show superparamagnetic behavior at room temperature, with transition to a blocked state at T_B^m94 K in ZFC and 119 K in AC susceptibility measurements, respectively, which depends on the applied field. The saturation magnetization and the coercivity measured at 4.2 K are 27.3 emu/g and 14.7 kOe, respectively. The particle size distribution was determined by fitting a magnetization curve obtained at 295 K assuming a log-normal size distribution. The interparticle interactions are found to influence the energy barriers yielding an enhancement of the estimated magnetic anisotropy, K=6×10⁶ erg/cm³. Mössbauer spectra obtained at higher temperatures show a gradual collapse of the magnetic hyperfine splitting typical for superparamagnetic relaxation. At 4.2 K, the Mössbauer spectrum was fitted with two magnetic subspectra with internal fields H_int of 490, 470 and 515 kOe, corresponding to Fe³⁺ ions in A and B sites.     

Magnetic and electronic phase transitions and magnetoresistance effect in the Pr0.5−xLaxSr0.5MnO3 (, 0.15) system

The electronic and magnetic phase transitions of Pr_0.5−xLa_xSr_0.5MnO₃ with x=0.10 and 0.15 were investigated. The M(T) and ρ(T) curves for these samples clearly show transitions from antiferromagnetic insulator to ferromagnetic semiconductor, ferromagnetic metal and finally to paramagnetic semiconductor as the temperature is increased from 5 to 300 K. Especially, two obvious protrudent peaks in the magnetoresistance curves MR(T) for these samples were clearly observed in the relative low magnetic field, 1 T. One peak appears at around the antiferromagnet-ferromagnet transition temperature T_N (150 K) with MR≈−23%, another occurs at around the ferromagnet-paramagnet transition temperature T_C(275 K ) with MR≈−8.2%. In addition, when the magnetic field was increased, the temperature corresponding to the MR peak at T_N shifts to lower temperature while the temperature corresponding to the MR peak at T_C is fixed.     

Observation of enhanced dielectric permittivity in Bi doped BaFe12O19 ferrite

The dielectric properties of a 2.5 mol% Bi₂O₃ doped Ba-ferrite (BaFe₁₂O₁₉) have been investigated. The specimen shows a drastically enhanced (≈ 10⁵ times) permittivity (ε) through local polarization of Fe³⁺ electronic charges activated with nearby Bi³⁺ sites. The ε value also depends reasonably on thermal annealing (causes grain growth) of the samples. The specimens comprising large particle sizes (1–20 μ m) usually exhibit smaller ε values and low dielectric losses.     

Domain wall pinning in polycrystalline perovskite La0.7Sr0.3MnO3

Reversible and irreversible domain wall (DW) motions have been investigated in La_0.7Sr_0.3MnO₃ ceramic samples using frequency-response complex permeability with various amplitudes of AC field. We also examine the effects of temperature in the range from 293 to 368 K and transverse DC magnetic field with a maximum of 4.40×10⁵ A/m on the real part of permeability (μ′). Two relaxations corresponding to reversible wall motions and domain rotations occur in low and high frequency regions, respectively. The irreversible DW displacements can be activated as the amplitude larger than the pinning field of 3 A/m, leading to an increase in μ′. The μ′ obeys a Rayleigh law at the temperature below 343 K or under DC field of less than 4.22×10⁴ A/m. The Rayleigh constant η increases from 5.45×10⁻² to 1.54×10⁻¹ (A/m)⁻¹ as the temperature rises from 293 to 343 K, and η decreases from 5.58×10⁻² to 3.67×10⁻² (A/m)⁻¹ with increasing DC field from 1.99×10³ to 4.22×10⁴ A/m.