Dosage des thiols par polarographie a impulsions

The determination of thiols has been studied by pulse polarography. A single peak is obtained if the concentration is less than 10^-4 M. The electrochemical reaction involves oxidation of mercury in presence of the thiol with adsorption of the mercury thiolate on the electrode. The method is more sensitive with a negative pulse; this corresponds to reduction of the mercury thiolate formed during the drop life. The sensitivity is about 10^-7 M, i.e. 3 p.p.b. calculated as sulfur. Peak potential values are given for H₂S, nine aliphatic thiols and benzenethiol. Peak height is proportional to concentration up to about 5 · 10^-5 M. The phenomena are more complicated for concentrations higher than 10^-4 M so that the method is not then analytically useful.     

Polarographic study of uracil derivatives

Eighteen uracil derivatives were studied by d.c. polarography, differential-pulse (d.p.)polarography and d.p. cathodic stripping voltammetry. In a borax buffer at ca. pH 7.6, uracil, thymine and derivatives such as 5-halouracils, 5-trifluoromethyl-,5-aza-,5-acetyl-, 5-formyl- and 5-vinyl-uracil produced well-defined peaks at potentials between 0 V and ca. 160 mV vs. silver/ silver chloride (satd. KCl). The peaks are ascribed to the formation of sparingly soluble mercury salts. For the other derivatives tested (e.g., 5-nitro- and 5-ethynyl-uracil and 6-substituted uracils), the peaks were less well-defined and in some cases the polarographic curves were very complex. 2-Thiouracil produced a single peak at ca. ?400 mV, but only at pH 12.2. The shapes, heights and potentials of the peaks depended on the kind and position of the substituent on the pyrimidine ring. Rectilinear relationships of peak current vs. concentrations were found for most compounds (10^?5-10^?4 M) by d.p. polarography; d.c.polarography was not tested quantitatively. For 5-fluorouracil and 5-vinyluracil, linear calibrations were found for concentrations of 0.5–5 × 10^?7 M by d.p. cathodic stripping voltametry. Interference studies showed that small amounts of chloride and phosphate did not interfere but 5-fluorodeoxyuridine, which did not itself produce a peak, and proteins interfered seriously.     

Electroanalytical studies of the pesticides menazon and its hydrolysis products

An electroanalytical study based on d.c. polarography, differential pulse polarography (d.p.p.) and coulometry is described for Menazon, S-[4, 6-diamino-1,3,5-triazin-2-yl)- methyl]-O,O-dimethylphosphorodithioate, and its alkaline hysdrolysis products in a (1 + 4) methanol/water medium. The responses of the different species are studied for analytical utility. Menazon itself produces two diffusion-controlled cathiodic waves or peaks at pH 4.78; the determination limit is 5.5 × 10^-7 M for the d.p. peak at about ?0.8 V vs. Ag/AgCl. The hydrolysis products obtained in 0.1 M sodium ydroxide give rise to four anodic waves. Acidification of the alkaline medium to pH 4.3 produces three well-defined waves; two cathodic and one anodic. The responses for the cathodic processes are linear with concentration over 2–2.5 orders of magnitude; the anodic wave is adsorption-controlled and provides linear response only at low concentrations. The detection limit for the hydrolysis products is 0.17 × 10^-6 M. Reaction mechanisms are proposed.     

Evaluation of derivative normal pulse polarography for use in metal speciation studies

A simple inexpensive microcomputer-orientated approach for obtaining pseudo-derivative polarograms is demonstrated. The method, called derivative normal pulse polarography (d.n.p.p.), produces better signal-to-noise ratios, and therefore lower detection limits, than differential pulse polarography (d.p.p.). The foremost advantage of d.n.p.p. is its relative freedom from influences of homogeneous chemical kinetics which makes it an excellent method for metal speciation studies. Response curve shapes for Pb(II) between 2 × 10^-4 and 8 × 10^-4 M exhibit excellent agreement with theory. Titration of EDTA with 0.01 M Cu(II) and 0.01 M Cd(II) using d.n.p.p. for detection exhibited recoveries of 98.0 and 99.5%, respectively.     

Determination of uranium in plutonium by differential linear sweep oscillographic polarography

The polarographic behavior of uranium in hydroxylamine hydrochloride was investigated by differential oscillographic polarography. A procedure is presented for the determination of uranium in plutonium for concentrations of uranium greater than 10 p.p.m. Analyses of solutions containing 22 common impurities found in plutonium metal revealed that antimony, copper, and titanium cause significant interference. A reversible peak corresponding to a one-electron reduction was obtained with a peak potential of -0.167 V vs. Hg pool electrode. The diffusion coefficient is 0.51·10^-5 cm²/sec and the diffusion current constant is 1.59 with an average relative standard deviation of 2.28%. The peak current of uranium can be affected by hydrochloric, nitric, perchloric, and sulfuric acids, depending on the acid concentration.     

Etude Polarographique De La Marcellomycine

Abstract

Polarographic study of marcellomycine.

d.c., a.c. and d.p. polarography and cyclic voltammetric techniques were used to investigate the electrochemical properties of marcellomycine. These are found to be quite similar to those of aclacinomycine or carminomycine, the main reversible two-electron wave being attributed tot he reduction of the quinonic structure. The molecule undergoes a degradation process starting in acidic medium and giving rise to the formation of two small irreversible waves at more negative potentials. This process is time, illumination and pH dependent. Important adsorption phenomena interfere in the investigated pH range but are lowered in very acidic medium. Quantitative measurements have been carried out at pH 1 and 6 in a 10^?3 to 10^?5 M concentration range using d.c. polarography. d.p. technique allows determinations in a restricted 10^?5 to 10^?4 M range. A detection limit of 1 · 10^?5 M has been fixed at pH 1.     

The determination of some 2-thiobarbiturates by cathodic stripping voltammetry

Pulse polarography and cyclic voltammetry are employed in studies of the electrochemical behaviour of 5-ethyl-5'-(l-methylbutyl)-2-thiobarbituric acid (I), l-methyl-5-ethyl-5'-(l-methylpropyl)-2-thiobarbituric acid (II) and l,3-dimethyl-5-ethyl-5'-p-chlorophenyl)-2-thiobarbituric acid (III) in the pH range 4–12. All three compounds show anodic and cathodic waves or peaks in this pH range. Compounds (I) and (II) are oxidized at mercury indicator electrodes to produce mercury salts which can adsorb thereon and are thus amenable to cathodic stripping voltammetric analysis (c.s.v.) down to concentrations of the order of 10^-6 M, which is superior to the sensitivities obtained by differential pulse polarography (d.p.p.) based on a reduction peak. Compound (III) oxidizes to produce sulphur which is subsequently plated as HgS. Again the sensitivity of the c.s.v. method is of the order of lO^-6 M and analytically superior to d.p.p. The optimum pH for the three determinations is 8. The determination of (II) in the presence of its oxygenated analogue and metabolite, phemitone, and the effect of chloride ions are reported.     

Polarographic Behavior of Eriochrome Red B and Its Complexes with Rare-Earth Ions

The polarographic behavior of Eriochrome Red B (ERB) and its complexes with rare-earth element (REE) ions in wide ranges of pH and concentrations was investigated by alternating-current polarography and cyclic linear-sweep voltammetry. A new polarographic method was proposed for the determination of heavy REEs and yttrium. The detection limit for REE(III) is 6 × 10^–7M. The method proposed was used for determining REE(III) in single crystals with valuable optical properties and in intermetallic compounds of the Tb–Al system.     

Determination of Methimazole and Carbimazole Using Polarography and Voltammetry

Abstract

Anodic waves of methimazole (I) (1-methylimidazole-2-thiol) and carbimazole (II) (1-ethoxycarbonyl-3-methyl-2-thio-4-imidazoline) on mercury electrodes correspond to mercury salt formation. Both compounds form in the thiono form a soluble complex at pH < 6, compound (I) at higher pH-values a slightly soluble salt of the thiol form. Electrode processes involving the thiol form are complicated by adsorption. Oxidation at solid electrodes occurs only at potentials more than 0.5 V more positive. For compound (I) spectrophotometry indicated pK_a=12.0 ± 0.2. By d.c. polarography in 0.1 M H₂SO₄ containing 10% ethanol the determination of both compounds is possible between 4 × 10^? and 1 × 10^?3 M, by differential pulse polarography between 1 × 10^? and 1 × 10^?4 M, by differential pulse voltammetry at HMDE between 5 × l0^?7 and 6 × 10^? M.     

Determination of total phthalate esters in wastewaters by differential pulse polarography

A reliable procedure for the determination of total phthalate esters as phthalic acid in environmental samples is based on differential pulse polarography (d.p.p.). The phthalate esters are extracted from the sample water with hexane; concentrated sulphuric acid/hexane partitioning provides effective removal of organic interferences. The individual phthalate esters are hydrolyzed by refluxing with 10 M potassium hydroxide to phthalic acid, which is extracted with ethyl acetate followed by evaporation of the extract. This procedure gives recoveries of 83–90%. The residue is dissolved in 0.1 M acetic acid/0.1 M potassium chloride for d.p.p. The otpimal conditions for polarography are discussed. The calibration graphs are linear over the range 2 × 10^?6–1 × 10^?4 M and the detection limit for phthalic acid is 5 × 10^?7 M. The method was successfully applied to determine total phthalate esters over the range 0.3–30 μg l^?1 in crude and treated wastewaters.     

An electroanalytical study of the anticancer drug dacarbazine

The electrochemical behaviour of dacarbazine [5-(3,3-dimethyl-1-triazenyl) imidazole-4-carboxamide; DTIC] was investigated by Tast and differential pulse polarography (d.p.p.) at the dropping mercury electrode, by cyclic and differential pulse voltammetry at the hanging mercury drop electrode and by anodic voltammetry at the glassy carbon electrode. Calibration graphs were obtained for 2×10^?8?2×10^?5 M DTIC by d.p.p., for 5×10^?9?1×10^?5 M by adsorptive stripping voltammetry ar a hanging mercury drop electrode, and for 1?10×10^?5 M by high-performance liquid chromatography with oxidative amperometric detection at a glassy carbon electrode. The methods are compared and applied to determine DTIC added to blood serum after a simple clean-up procedure.     

Electrochemical determination of prolintane in pharmaceutical formulations and in human urine

The oxidative behavior of 1-[1-(phenylmethyl)butyl]pyrrolidine, prolintane, was studied at a glassy carbon electrode using linear-sweep and differential-pulse voltammetry. The oxidation process was shown to be irreversible using 0.04 M Britton–Robinson buffer and was diffusion-adsorption controlled. Two voltammetric methods were developed for the determination of prolintane using different techniques: linear-sweep and differential-pulse voltammetry. The peak current varied linearly with prolintane concentrations in the range of 1.0 × 10⁻⁵ −2.5 × 10⁻⁴ M, with a detection limit of 8.5 × 10⁻⁶ and 4.0 × 10⁻⁶ M, and with relative standard deviations of 2.1 % and 3.1 %, respectively. The methods were applied to commercial preparations, giving relative errors less than 3.1 % and relative standard deviations lower than 4.8 % (n = 10). Determination of prolintane (down to the 8.5 × 10⁻⁸ M level) can be performed by using a preconcentration step prior to the determination by differential-pulse voltammetry in 0.04 M Britton–Robinson buffer (pH 8.0) with preconcentration potential of 0.0 V. The detection limit was found to be 6.2 × 10⁻⁸ M (4 min preconcentration) and the relative standard deviation for 2.5 × 10⁻⁷ M prolintane (n = 5) was 4.6 %. Applicability to human urine analysis is illustrated (recovery 98 ± 2 %). Standard additions method can be used to determine prolintane in real samples of urine.     

Electrochemical Reduction of Metronidazole and Its Determination in Pharmaceutical Dosage Forms by D.C. Polarography

Abstract

A simple d.c. polarographic method has been developed for the determination of metronidazole in dosages forms. In Robinson - Britton buffer (pH 4.38) and in presence of 1.60 × 10^?3 % Triton X-100, the drug produced a well defined 4-electron polarographic wave followed by another wave of about half the height of the first wave. The current is proportional to the concentration and permits the drug to be determined by d.c. polarography in the concentration range 5.0 × 10^?5 -7.0 × 10^?4 M. Results obtained by the proposed method are in excellent agreement with that provided by the USP-XX method. A rapid, sensitive and accurate polarographic method for the determination of metronidazole in the tablets which are produced locally is proposed.     

Polarographic Determination of Aztreonam

Abstract

The polarographic behaviour of Aztreonam is studied. In acid media, at pH values lower than 6, in differential pulse polarography a peak is observed at a potential close to ? 0.6 volts. The optimum conditions for the polarographic signal are established and the different parameters affecting the electrochemical process are studied. The relationship between peak intensity and the concentration of Aztreonam is linear for concentrations lower than 1.0 ? 10^?5 M, the detection limit being 1.4 × 10^?8 M It was observed that the presence of 1-arginine does not affect the polarographic signal of Aztreonam to any significant extent.     

Determination of trace thiocyanate by linear sweep polarography

In a thiocyanate solution containing iron (II), nitrite and ascorbic acid, a linear-sweep polarographic wave appears at ?0.42 V (vs. SCE). In anodic sweeps, the derivative peak current is directly proportional to the concentration of thiocyanate over the range 2×10^?8?1×10^?6 M; the detection limit is 1×10^?8 M. The procedure is used for the determination of trace thiocyanate (10^?3?10^?4 M) in saliva. The mechanism of the electrode process is discussed; the polarographic wave is ascribed to catalytic reduction of dissolved oxygen in the presence of an adsorbed ternary Fe/SCN/NO complex.     

Analytical Determination of N-(2-Mercapto Propionyl)Glycine (Tiopronin) by Voltammetric Methods

Abstract

The anodic processes which occur at the mercury electrode in N-(2-mercaptopropinyl)glycine (tiopronin) solutions are studied by polarographic techniques (d.c., d.p. and a.c₁.), controlled potential coulometry and cathodic stripping voltammetry. According to the observed electrochemical behaviour the overall electrode process is the formation of a mercury(II)-mercaptide. Adsorption on the electrode of both the mercaptide and the free thiol is present. The d.p.p. peak at -0.58 V or the voltammetric stripping peak at -0.56 V are used for the analytical determination of N-(2-mercaptopropionyl)glycine within the concentration ranges 7.0 10^?5 - 6.8 10^?6 mol 1^?1 or 3.0 10^?7 - 1.0 10^?9 mol I^?1, respectively. Calibration functions are reported in both cases. The interference of several organic compounds is described.     

Electrochemical study of 1,2-Naphthoquinone-4-sulphonate and 1,2-Naphthoquinone semicarbazone

Summary A study of the electrochemical characteristics of 1,2-naphthoquinone-4-sulphonate, sodium salt, and of the semicarbazone of 1,2-naphthoquinone (Naftazone) was carried out using d.c., a.c. and d.p. polarography and cyclic voltammetry. Changes in the waves as a function of concentration and pH indicate evidence of adsorption phenomena at the potential of the reduction wave. These techniques also indicate the formation of a mercury derivative in the case of Naftazone. The quantitative determination of these two compounds is possible by polarography. Limits of detection are 5×10^–6 and 5×10^–8 M, respectively.

---

Elektrochemische Untersuchung von 1,2-Naphthochinon-4-sulfonat und 1,2-Naphthochinon-semicarbazon

Zusammenfassung Die elektrochemischen Eigenschaften von 1,2-Naphthochinon-4-sulfonat und -semicarbazon (Naftazon) wurden mit Hilfe der Gleichstrom-, Wechselstrom und Differentialpuls-Polarographie sowie der cyclischen Voltammetrie untersucht. Veränderungen an den Stufen in Abhängigkeit von Konzentration und pH-Wert deuten auf Adsorptionsvorgänge beim Potential der Reduktionsstufe hin. Im Falle von Naftazon wurde die Bildung eines Quecksilberderivats nachgewiesen. Beide Substanzen können polarographisch mit Nachweisgrenzen von 5×10^–6 bzw. 5 × 10^–8 M bestimmt werden.

     

Determination of physiological thiols by electrochemical detection with piazselenole and its application in rat breast cancer cells 4T-1

Glutathione (GSH), the most abundant cellular thiol, has been shown to play an important role in maintaining cellular redox equilibrium that is pivotal for cell growth and function. In the present paper a novel electrochemical probe of piazselenole containing a Se-N bond was well developed for the determination of GSH. The cyclic voltammogram of piazselenole scanned at 100 mV/s displayed an irreversible reduction peak at -0.106 V (vs Ag/AgCl electrode) and a significant peak current decrease could be further provoked with the addition of GSH into piazselenole solution. On the basis of the peak current decrease of piazselenole recorded by differential pulse voltammetry with the increase of GSH concentration, a working curve was constructed for GSH determination in the range of 5.0 x 10(-10) approximately 2.2 x 10(-8) M with the linear regression equation as DeltaiP (10(-6)A) = 0.0952 + 0.4287 x CGSH (10(-8) M) and the detection limit (3sigma) as 83 pM. The proposed method was satisfactorily applied to the extracts of rat breast cancer cells 4T-1 for intracellular thiols detection.     

The specific fluorimetric determination of digoxin.

The simultaneous determination of Cd, Cu, Pb and Zn in lead and zinc concentrates by fundamental, second-harmonic and linear-sweep a.c. and pulse polarographic methods is described. Calibration curves are linear over wide concentration ranges, so that both major and minor trace constituents can be determined in the same experiment; thus the polarographic method is highly competitive with atomic absorption spectrometry (a.a.s.). Conventional a.c. polarography and a.a.s. were compared in the first instance with conservative instrumentation. More sophisticated polarographic methods were then utilized; with the phase-selective linear sweep a.c. (fundamental- and second-harmonic) methods the four elements were determined simultaneously from voltammograms obtained in less than 20 s down to the 10^-6-10^-7M concentration range.     

Cathode ray polarography and differential pulse polarography of the catalytic molybdenum(VI) wave

The optimum conditions of electrolyte composition and pH were studied for the cathode ray polarography (c.r.p.) of the catalytic molybdenum(VI) wave; 1–2 M potassium nitrate at pH 1.6–2.2 is optimum, the detection limit is 3 × 10^-9 M (0.3 ppb) molybdenum(VI). Equal molar concentrations of foreign electroactive substances do not interfere at the potential of the molybdenum wave and 500-fold amounts of these can be tolerated if their c.r.p. peaks are separated from the molybdenum wave by 0.1 or 0.2 V. Similar conditions were used for the differential pulse polarography of the catalytic wave. The detection limit is 2 × 10^-8 M (2 ppb). being limited in part by lead impurities which contribute to the background.