Differential pulse anodic stripping voltammetry at the wall-jet electrode

Differential pulse anodic stripping voltammetry at the wall-jet electrode requires careful consideration of flow conditions in the plating and stripping steps as well as the electrochemical parameters such as modulation amplitude and clock period. A systematic appraisal of the various factors affecting the differential pulse stripping current is described. Although the stripping current depends on the stripping solution flow rate, the differential pulse mode is preferred to dc stripping because of its greater sensitivity and the abililty to obviate oxygen interference.     

Subtractive differential pulse anodic stripping voltammetry at a stationary mercury-coated glassy carbon electrode

The application of subtractive mode differential pulse anodic stripping voltammetry (SDPASV) at a stationary mercury-coated glassy carbon electrode for the analysis of labile Zn(II), Cd(II), Pb(II) and Cu(II) is described. It is shown that the method has an improved sensitivity to Cu(II) owing to elimination of high background currents normally encountered in normal mode DPASV at the TFME. The sensitivity limits of the present method to Cd(II) and Cu(II) is estimated to be 0.025 and 0.067 ppb respectively, when a 2 min deposition time is used. It is suggested that the high sensitivity of the method coupled to the relative simplicity of the stationary electrodes could make the method useful in environmental and natural water studies.     

Differential-pulse anodic stripping voltammetry of copper with a chemically-modified glassy carbon electrode

Copper at the low or fractional ng g^?1 level in 0.1 M oxalic acid solutions at pH 1.6 is electrodeposited on a chemically-modified glassy carbon electrode with surface-bound

groups at ?0.6 V vs. Ag/AgCl (3.3 M KCl). The deposit is then anodically stripped in the same solution, a current-potential curve being recorded by the differential-pulse technique. The advantages of this electrode over an unmodified glassy carbon electrode include higher sensitivity, precision and selectivity; the modified electrode can be used 50–100 times without further treatment.     

Comparison of linear scan and differential pulse anodic stripping voltammetry at a thin mercury film glassy carbon electrode

The use of the differential pulse mode in anodic stripping voltammetry with an electrode consisting of a thin mercury film deposited in situ on a glassy carbon support leads to detection limits which are 3–5 times lower than if a simple linear scan is used at the same electrode. If the glassy carbon electrode has a high base current, the improvement in detection limit with differential pulse will be even greater. Differential pulse peak currents, however, are more susceptible to interference by surface-active substances, and undetected adsorption/desorption effects can cause serious errors. Precautions which are necessary to maintain a glassy carbon electrode in good condition are described.     

Electrochemical behavior of lead(II) at poly(phenol red) modified glassy carbon electrode, and its trace determination by differential pulse anodic stripping voltammetry

Poly(phenol red) (denoted as PPR) films were electrochemically synthesized on the surface of a glassy carbon electrode (GCE) by cyclic voltammetry to obtain a chemically modified electrode (denoted as PPR-GCE). The growth mechanism of PPR films was studied by attenuated total reflection spectroscopy. This PPR-GCE was used to develop a novel and reliable method for the determination of trace Pb²⁺ by anodic stripping differential pulse voltammetry. At optimum conditions, the anodic peak exhibits a good linear concentration dependence in the range from 5.0 × 10⁻⁹ to 5.0 × 10⁻⁷ mol L⁻¹ (r = 0.9989). The detection limit is 2.0 × 10⁻⁹ mol L⁻¹ (S/N = 3). The method was employed to determine trace levels of Pb²⁺ in industrial waste water samples. Correspondence: Gongjun Yang, Ming Shen, College of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002, P.R. China     

Determination of copper by anodic stripping voltammetry on a glassy carbon electrode using a continuous flow system

 A successful flow-through system was developed for trace analysis of copper using DPASV with a glassy-carbon electrode. Periodical chemical regeneration of the electrode with a 1 mol/L NaOH solution increased sensitivity and precision. The method was shown to be applicable with a detection limit of 0.56 μg/L, with a determination time of less than 7 min per measurement (without deaeration time). The drawback of the system is the 10 min deaeration time. The system gave an accuracy of 0.090±0.005% for a certified reference material of low alloy steel containing 0.090±0.004% Cu. Applicability to various fresh water samples with a Cu content between 1.57 and 13.11 μg/L with an RSD<2.36% is illustrated. Received: 11 March 1996/Revised: 1 July 1996/Accepted: 4 July 1996     

Linear scan stripping voltammetry of copper(II) at the chemically modified carbon paste electrode

A new chemically modified electrode (CME), -benzoinoxime (CUPRON) modified carbon paste electrode, for determining copper(II) is reported because of its excellent selectivity and sensitivity. The electrode is made by mixing a quantity of CUPRON (25%, w/w) with graphite powder (50%, w/w) and paraffin oil (25%, w/w). The CME preferentially deposits copper from the pH 8.5 NH₃-NH₄Cl buffer solution containing copper(II) under an open circuit and most of metal ions do not interfere with the measurements. The detection limit (S/N of three) for determining Cu(II) is 3 × 10^–10 g/ml after 10 min accumulation in fast linear scan stripping voltammetric measurement. Linear calibration curves are obtained for Cu(II) concentration ranged from 1 × 10^–8 M to 1 × 10^–6 M. The response can be maintained with relative standard deviation of 6.0% in a 5 × 10^–6 M Cu(II) solution after eight accumulation/measurement/ regeneration cycles at the same electrode surface. The effect resulted from carbon paste preparation, reduction potential, electrode renewal, electrolyte and solution pH, preconcentration time, concentration dependence, possible interference and other variables has been evaluated. As for application, the CME demonstrates its high sensitivity and copper-selectivity in complex composition samples, such as anodic mud and polluted water.     

Determination of copper by anodic stripping voltammetry on a glassy carbon electrode using a continuous flow system

 A successful flow-through system was developed for trace analysis of copper using DPASV with a glassy-carbon electrode. Periodical chemical regeneration of the electrode with a 1 mol/L NaOH solution increased sensitivity and precision. The method was shown to be applicable with a detection limit of 0.56 μg/L, with a determination time of less than 7 min per measurement (without deaeration time). The drawback of the system is the 10 min deaeration time. The system gave an accuracy of 0.090±0.005% for a certified reference material of low alloy steel containing 0.090±0.004% Cu. Applicability to various fresh water samples with a Cu content between 1.57 and 13.11 μg/L with an RSD<2.36% is illustrated. Received: 11 March 1996/Revised: 1 July 1996/Accepted: 4 July 1996     

Selenium-coated carbon electrode for anodic stripping voltammetric determination of copper(II)

We describe a new and promising type of selenium film electrode for anodic stripping voltammetry. This method is based on formation of copper selenide onto an in-situ formed selenium-film carbon electrode, this followed by Osteryoung square-wave anodic stripping voltammetry. Copper(II) is also in-situ electroplated in a test solution containing 0.01 mol L^-1 hydrochloric acid, 0.05 mol L^?1 potassium chloride and 500 µg L^?1 Se(IV) at a deposition potential of ?300 mV. The well-defined anodic peak current observed at about 200 mV is directly proportional to the Cu(II) concentration over the range from 1.0 to 100 µg L^?1 under the optimized conditions. The detection limit (three sigma level) is 0.2 µg L^?1 Cu(II) at 180 s deposition time. Relatively less interferences are shown from most of metal ions except for antimony(III). The method can be applied to analyses of river water and oyster tissue with good accuracy.     

Differential-pulse anodic stripping voltammetry at mercury-poly(4-vinylpyridine) coatings on glassy carbon electrodes

The coating layer is simple to prepare and when the HG²⁺ within the layer is reduced it proves useful for determination of Cd²⁺ and Pb²⁺, but not Cu²⁺. The inherent filtering ability of the poly(vinylpyridine) excludes gelatin, which adsorbs on mercury film electrodes causing irreproducible results.     

Determination of trace metoclopramide by anodic stripping voltammetry with nafion modified glassy carbon electrode

A novel method is described for determination of metoclopramide (MCP) by second-derivative adsorptive anodic stripping voltammetry with a nafion-modified electrode. The stripping peak current is proportional to the concentration of MCP over the range 1.2×10⁻⁹–4.6×10⁻⁷ M. The detection limit is 8.0×10⁻¹¹ M with 4-min accumulation. The method has been successfully applied to the determination of MCP in human serum.     

Adsorptive stripping voltammetry of nickel at a bare glassy carbon electrode

A bare glassy carbon electrode is applied to nickel determination by adsorptive stripping voltammetry in the presence of dimethylglyoxime as a complexing agent. A procedure of nickel determination and electrode regeneration was proposed. The calibration graph for Ni(II) for an accumulation time of 120?s was linear from 2?×?10^?9 to 1?×?10^?7?mol?L^?1. The detection limit was 8.2?×?10^?10?mol?L^?1. The relative standard deviation for a solution containing 2?×?10^?8?mol?L^?1 of Ni(II) was 4.1%. The proposed procedure was applied for Ni(II) determination in certified water reference materials.     

The differential pulse anodic stripping voltammetry of copper and lead and their determination in EDTA extracts of soils with the mercury film glassy carbon electrode

The differential pulse anodic stripping voltammetry of copper and lead at the mercury film glassy carbon electrode is discussed. The mercury film prevents the occurrence of a monolayer stripping peak for copper. The influence of antimony and bismuth on the anodic stripping voltammetric behaviour of copper and lead is discussed. An interaction between copper and antimony distorts the copper stripping peak and gives rise to an intermediate peak. The method described is suitable for determining copper and lead simultaneously in EDTA extracts of soils.     

Differential pulse anodic stripping voltammetry detection of metallothionein at bismuth film electrodes

As a representation of metalloproteins, metallothionein (MT), which plays important biological and environmental roles such as in the metabolism and detoxification of some metals, was detected at bismuth film electrode (BiFE) by differential pulse anodic stripping voltammetry (DPASV). In pH 2–5.5, two well-defined anodic peaks were produced and attributed to the Zn²⁺ and Cd²⁺ inherent to MT. The calibration plot of DPASV peak currents for Cd²⁺ inherent to MT versus MT concentrations showed a good linearity with a detection limit of 3.86 × 10⁻⁸ mol/L for MT. As a non-toxic excellent electrode material, BiFE shows good performance for detecting MT, and is expected to find further applications in the studies of many other metalloproteins.     

An evaluation of differential pulse anodic stripping voltammetry at a rotating glassy carbon electrode for the determination of cadmium,copper, lead and zinc in antarctic snow samples

A procedure is described for the determination without preconcentration of Cd, Cu, Pb and Zn in Antarctic snow, based on differential pulse anodic stripping voltammetry at a rotating glassy carbon electrode with in situ mercury plating. Thirty four surface snow samples from Adelaide Island in the Antarctic Peninsula demonstrate the scope of this method, and allow an assessment of local heavy metal sources such as the rock, the sea, and a manned base. The zinc data are affected by container contamination, but concentrations as low as 0.005, <0.02 and 0.05 ng g^-1 were measured for Cd, Cu and Pb, respectively.     

Differential pulse cathodic stripping voltammetry of the copper complexes of glycyl-L-histidyl-glycine at a hanging mercury drop electrode

The behaviour of the copper complexes of glycyl-L-histidyl-glycine (GHG) was investigated using cyclic voltammetry and differential pulse voltammetry after their adsorptive accumulation on the surface of a hanging mercury drop electrode (HMDE). The nature of the observed cathodic and anodic peaks was established and optimum conditions were found for the differential pulse cathodic stripping voltammetric detemination of GHG at the 1 x 10(-8)M concentration level using adsorptive accumulation at -0.20 V vs. Ag/AgCl reference electrode and the cathodic stripping peak around -0.4 V (pH 8.3). This peak corresponds to the reduction of the Cu(I)-GHG complex formed at the HMDE surface as an intermediate in the reduction of Cu(II)-GHG to Cu(O)amalgam.     

Determination of copper ion by square wave anodic stripping voltammetry at antimony trioxide-modified carbon nanotube paste electrode

In this work, an antimony trioxide-modified multi-walled carbon nanotube paste electrode (Sb₂O₃/CNTPE) was employed for determination of Cu²⁺ ions by using square wave anodic stripping voltammetry (SWASV) in the presence of 8-hydroxy-7-iodo-5-quinoline sulfonic acid (HIQSA) as a chelating agent. The field emission scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS) and electrochemical impedance spectroscopy (EIS) methods were applied to estimate the morphology and properties of the modified electrode. Measurements related to SWASV were taken in 0.6 M HCl at ?1.0 V versus Ag|AgCl|KCl (3 M) for 90 s (deposition step). After equilibrium time of 15 s, an ASV appeared at 0.0 V versus Ag|AgCl|KCl (3 M) (stripping step). The sensor depicted a fairly linear response for Cu²⁺ in the concentration range of 2–100 ppb with appropriate detection limit about 0.39 ppb and limit of quantification about 1.3 ppb. The stability of the modified electrode during 7 weeks and its behavior in the presence of some metal ions was evaluated. The practical applicability of the Sb₂O₃/CNTPE was established on the voltammetric determination of Cu²⁺ in tap water as a sample.