Electrochemical study of Meldola's blue,methylene blue and toluidine blue immobilized on a SiO<Subscript>2</Subscript>/Sb<Subscript>2</Subscript>O3 binary oxide matrix obtained by the sol-gel processing method

SiO₂/Sb₂O₃ (SiSb), having a specific surface area, S _BET, of 788 m² g⁻¹, an average pore diameter of 1.9 nm and 4.7 wt% of Sb, was prepared by the sol-gel processing method. Meldola's blue (MeB), methylene blue (MB) and toluidine blue (TB) were immobilized on SiSb by an ion exchange reaction. The amounts of the dyes bonded to the substrate surface were 12.49, 14.26 and 22.78 μmol g⁻¹ for MeB, MB and TB, respectively. These materials were used to modify carbon paste electrodes. The midpoint potentials (E _m) of the immobilized dyes were −0.059, −0.17 and −0.18 V vs. SCE for SiSb/MeB, SiSb/MB and SiSb/TB modified carbon paste electrodes, respectively. A solution pH between 3 and 7 practically did not affect the midpoint potential of the immobilized dyes. The electrodes presented reproducible responses and were chemically stable under various oxidation-reduction cycles. Among the immobilized dyes, MeB was the most efficient to mediate the electron transfer for NADH oxidation in aqueous solution at pH 7. In this case, amperometric detection of NADH at an applied potential of 0 mV vs. SCE gives linear responses over the concentration range of 0.1–0.6 mmol L⁻¹, with a detection limit of 7 μmol L⁻¹.     

The role of triplet states in dye sensitization of ZnO electrodes

The quantum efficiency of photooxidation of a number of xanthene dyes at ZnO single crystal electrodes has been found to depend on the solution concentration of a triplet quenching agent, FeCN^4?₆, providing evidence for triplet state participation in the oxidation reaction.     

A New Mussel‐Inspired Polydopamine Sensitizer for Dye‐Sensitized Solar Cells: Controlled Synthesis and Charge Transfer

The efficient electron injection by direct dye‐to‐TiO₂ charge transfer and strong adhesion of mussel‐inspired synthetic polydopamine (PDA) dyes with TiO₂ electrode is demonstrated. Spontaneous self‐polymerization of dopamine using dip‐coating (DC) and cyclic voltammetry (CV) in basic buffer solution were applied to TiO₂ layers under a nitrogen atmosphere, which offers a facile and reliable synthetic pathway to make the PDA dyes, PDA‐DC and PDA‐CV, with conformal surface and perform an efficient dye‐to‐TiO₂ charge transfer. Both synthetic methods led to excellent photovoltaic results and the PDA‐DC dye exhibited larger current density and efficiency values than those in the PDA‐CV dye. Under simulated AM 1.5 G solar light (100 mW cm^?2), a PDA‐DC dye exhibited a short circuit current density of 5.50 mW cm^?2, corresponding to an overall power conversion efficiency of 1.2 %, which is almost 10 times that of the dopamine dye‐sensitized solar cell. The PDA dyes showed strong adhesion with the nanocrystalline TiO₂ electrodes and the interface engineering of a dye‐adsorbed TiO₂ surface through the control of the coating methods, reaction times and solution concentration maximized the overall conversion efficiency, resulting in a remarkably high efficiency.     

Structural,electrochemical, and adsorption studies of Ni and Zn benzylimidazole coordination polymers with terephthalate linkers

Two coordination polymers, [Ni(bim)₂(L1)(H₂O)₂] _n (CP-1) and [Zn(bim)(L1)(Cl)] _n (CP-2) (bim = 1-benzylimidazole, L1 = terephthalic acid), were synthesized and characterized by physicochemical and spectroscopic methods. The Ni(II) center in CP-1 is octahedral, while the Zn(II) center in CP-2 is tetrahedral. CP-1 and CP-2 were used to modify carbon paste electrodes to assess their effect on the electrochemical behavior of ferricyanide. The redox reactions of ferricyanide on both electrodes proved to be reversible and diffusion controlled, with ferricyanide diffusion coefficients for CP-1 and CP-2 of 1.88 × 10⁵ and 3.44 × 10⁵ cm² s^?1, respectively. These coordination polymers were also investigated for their adsorption behavior toward two dyes: Chicago sky blue and methylene blue. CP-1 and CP-2 both rapidly adsorbed the anionic Chicago sky blue dye by different intermolecular interactions; in contrast, the cationic methylene blue dye was adsorbed to a lesser extent. The adsorption of these CPs depends on the charge but not the size of the dye. Addition of methanolic potassium nitrate solution caused the release of the adsorbed dyes.     

Electrochemical investigations on the analysis of reactive dyes with monoazo- and monoanthraquinone structures

Summary Qualitative voltammetric determination of reactive dyes is possible down to concentrations of about 10^–5 mol/l using DC-polarography. Using rotating solid electrodes (glassy carbon) a detection limit of about 10^–4 mol/l can be obtained. Reduction involves chiefly only the azo- and anthraquinoid groups, respectively, whereas the reactive functionality of these dyes shows electroactivity at much more negative potentials. Only the dichloro-quinoxaline group gives signals superimposed on the reduction of anthraquinoid groups. Discrimination between an original reactive dye and its hydrolysate (containing a hydrolytically destroyed reactive group) can be achieved, if the dye contains further cleavable groups such as benzamido substituents in conjugation to the chromophor as is seen with Azo-red I. Cleavage of such a group shifts the reduction potential for about 130 mV to more negative values.     

Photovoltaic performance of nanostructured zinc oxide sensitised with xanthene dyes

The photovoltaic properties of nanostructured ZnO electrodes prepared from commercially available ZnO nanoparticles (Degussa) and sensitised with xanthene dyes are explored. We have used Eosin Y, Eosin B and Mercurochrome and compared their performance to that of the more common N719 dye. We observe that these dyes efficiently sensitise commercial ZnO nanopowder and yield efficiencies that are very competitive with respect to those provided by N719. Local photocurrent and transmittance measurements as a function of the wavelength confirm the good performance of the xanthene dyes in the absorption maxima. We have prepared polymer-sealed cells and measured the short-circuit current of the devices under continuous illumination at 200 mW/cm² corresponding to twice the standard solar light intensity. The organic dyes show very good stability properties under these conditions. The combination of a versatile metal oxide such as ZnO and inexpensive organic dyes should be considered as a promising alternative in the field of dye-sensitised solar cells.     

Change of Boron Substitution Improves the Lasing Performance of Bodipy Dyes: A Mechanistic Rationalisation

Bodipy laser dyes are highly efficient but degrade rapidly in solution by reacting with in situ generated singlet oxygen (¹O₂). To increase the lasing lifetimes of these dyes, we have designed and synthesised two different congeners of the widely studied Pyrromethene 567 (PM567) by substitution at the boron centre and/or at both the boron centre and the meso position. The two new dyes showed high lasing efficiencies with increased photostability. The results of theoretical and pulse radiolysis studies revealed that the substitution at the boron centre reduced the ¹O₂ generation capacity of these dyes as well as their rate of reaction with ¹O₂, thereby enhancing their lifetimes even under lasing conditions.     

Dopamine and Glucose Sensors Based on Glassy Carbon Electrodes Modified with Melanic Polymers

This work deals with the study of polymers electrogenerated from different catechols at glassy carbon electrodes and the analytical applications of the resulting modified electrodes for dopamine quantification and glucose biosensing. The electropolymerization was performed from a 3.0×10^?3 M catechol solution (catechol, dopamine, norepinephrine, epinephrine or L ‐dopa in a 0.050 M phosphate buffer pH 7.40) by applying 1.00 V for 60 min. The properties of the polymers are very dependent on the nature of the catechol, L ‐dopa being the best. Glassy carbon electrodes modified with melanic polymers electrogenerated from L ‐dopa and norepinephrine were found to be suitable for dopamine determinations in flow systems, although the behavior was highly dependent on the nature of the monomer. Detection limits of 5.0 nM dopamine and interferences of 9.0 and 2.6% for 5.0×10^?4 M ascorbic acid and 5.0×10^?5 M dopac, respectively, were obtained at the glassy carbon electrode modified with a melanin‐type polymer generated from L ‐dopa (using 1.0×10^?3 M AA in the measurement solution). The advantages of using a melanin‐type polymer generated from dopamine to improve the selectivity of glucose biosensors based on carbon paste electrodes containing Pt and glucose oxidase (GOx) are also discussed. The resulting bioelectrodes combines the high sensitivity of metallized electrodes with the selectivity given by the polymeric layer. They exhibit excellent performance for glucose with a rapid response (around 10 seconds per sample), a wide linear range (up to 2.5×10^?2 M glucose), low detection limits (143 μM) and a highly reproducible response (R.S.D of 4.9%). The bioelectrodes are highly stable and almost free from the interference of large excess of easily oxidizable compounds found in biological fluids, such as ascorbic acid (AA), uric acid (UA) and acetaminophen.     

New Ion-Selective Electrodes for Determination of Bupivacaine and Oxybuprocaine

Abstract

PVC membrane electrodes selective for hydrochlorides of the anaesthetics bupivacaine (BpC) and oxybuprocaine (ObC) are prepared. The electrodes have a near Nernstian slope (58 mV for BpC and 51 mV for ObC electrodes) over the range of 1.6 × 10^?5-10^?1M and 1.3 × 10^?1M for BpC and ObC electrodes, respectively. The change in pH of the test solution within the ranges 2.5–6.0 and 3.0–7.4 does not affect the EpC-and ObC-electrodes, respectively. The electrodes have very long life times (10 days for BpC, and 3 months for ObC) and exhibit good seletivity for the investigated compounds with respect to a large number of inorganic cations and organic substances of biological importance. The isothermal coefficients of the electrodes are calculated from the standard electrode potentials at different temperatures. BpC and ObC are determined successfully in some pharmaceutical preparations using the calibration graph technique and potentiometric titration.     

Synthesis,characterization and dyeing assessment of novel acid azo dyes and mordent acid azo dyes based on 2-hydroxy-4-methoxybenzophenone-5-sulfonic acid on wool and silk fabrics

Novel acid mono azo and mordent acid mono azo dyes were synthesized by the coupling of diazonium salt solution of different aromatic amines with 2-hydroxy-4-methoxybenzophenone-5-sulfonic acid. The resulting dyes were characterized by spectral techniques like elemental analysis, IR, ¹H-NMR and UV visible spectroscopy. The dyeing performance of all the dyes was evaluated on wool and silk fabrics. The dyeing of chrome pre-treated wool and silk fabrics showed better hues on mordented fabrics. Dyeing of wool and silk fabrics resulted in pinkish blue to red shades with very good depth and levelness. The dyed fabrics showed excellent to very good light, washing, perspiration, sublimation and rubbing fastness.     

Novel Cyanine Dyes: Synthesis,Characterization and Photosensitization‐Structure Correlation

Novel furo, thieno and pyrrolo[2,3‐b]pyrazole cyanine dyes were synthesized. The structure‐photosensitization properties correlation of the dyes were examined in 95% ethanol solution by absorption spectroscopy. The chemical structure of the starting biheterocyclic compounds and their derived cyanine dyes were confirmed by elemental analysis, IR and ¹H NMR spectroscopy.     

Coated wire linear alkylbenzenesulfonate sensor based on polypyrrole and improvement of the selectivity behavior

The potentiometric behavior of coated wire electrodes based on dodecylbenzenesulfonate-doped polypyrrole (PPy-DBS) and hyamine as ion exchanger was investigated. The PPy-DBS was prepared electrochemically by anodic polymerization of pyrrole in the presence of DBS⁻ ions in aqueous solution and used as ionophore for construction of the sensor. Two types of coated wire electrodes made of PVC-PPy-DBS and PVC-Hyamine-DBS, plasticized with ortho-nitrophenyloctylether (o-NPOE) showed the Nernstian behavior (with respective calibration slopes of about 58 and 60 mV per decade) over the DBS⁻ concentration range of 3.0×10⁻⁶ to 1.1×10⁻³ M and 5.0×10⁻⁶ to 1.3×10⁻³ M, respectively. The influence of membrane composition, type of plasticizer, and pH of test solution on the potentiometric responses of the two electrodes was investigated. The potentiometric response was independent of the pH of test solution in the range 3-10. The response time of electrodes was fast (10 s for both types of electrode), and they can be used for at least 3 months without any significant change in potential. The proposed electrodes revealed very good selectivity for DBS⁻ ion over diverse inorganic and organic anions. The potentiometric selectivity coefficients for the PPy-DBS based electrode revealed a significant improvement as compared to the electrode made by conventional Hyamine-DBS (Hya-DBS) anion exchanger. The proposed electrode was used for determination of DBS⁻ ion in some commercial detergents. The results of the potentiometric determinations were in satisfactory agreement with those obtained by a standard method (two-phase titration).     

Novel Ag ion-selective electrodes based on two new mixed azathioether crowns containing a 1,10-phenanthroline sub-unit

Novel polymeric membrane (PME) and coated graphite (CGE) silver-selective electrodes based on two recently synthesized mixed azathioether crowns containing a 1,10-phenanthroline sub-unit were prepared. The electrodes reveal a Nernstian behavior over quite wide Ag⁺ ion concentration ranges with a very low limits of detection (LOD) (i.e. down to 1.0×10⁻⁸ M for CGEs and 8.0×10⁻⁷ M for PMEs). The potentiometric responses are independent of the pH of the test solution in the pH range 3.0-7.0. The electrodes possess advantages of low resistance, very fast response time, relatively long lifetimes and, especially, good selectivities relative to a wide variety of other cations. The electrodes were used, as indicator electrodes, in the potentiometric titration of silver ion and in the determination of Ag⁺ in waste water, photographic emulsion and radiographic and photographic films.     

Iodide-Selective PVC Membrane Electrodes Based on Five Transitional Metal Chelates of bis-furfural-semi-o-tolidine

Abstract

Some new PVC membrane electrodes based on Co(II), Mn(II), Ni(II), Cu(II), and Zn(II)chelates of bis-furfural-semi-o-tolidine as carriers are described. The electrodes exhibited different selectivity behaviour compared with the electrode using a classical anion exchanger such as tetraalkyl ammonium. The results showed that the Cobalt(II) chelate-based electrodes had a Nernstian response to iodide ion ranging from 1.0 × 10^?1 to 1.0 × 10^?6 mol.L^?1 in a phosphate buffer solution of pH 2.0 with a detection limit of 6.4 × 10^?7 mol.L^?1 and a slope of 57.8 mV/dec at 25deg;C. The response mechanism was also investigated by use of both a.c. impedance and SPQC techniques. The Co(II) chelate-based electrodes were used to determine the iodide content of a drug with satisfactory results.     

Rapid decolorization of water soluble azo-dyes by nanosized zero-valent iron immobilized on the exchange resin

Nanosized zero-valent iron (NZVI) supported on the cation exchange resin was synthesized and applied to decompose some water soluble azo dyes. The decomposition efficiency for azo dyes was evaluated by using the aqueous suspensions and parked column of this material. Batch experiments indicated that this novel material exhibited excellent degradation ability for 0.05 g·L1 of Acid Orange 7, Acid Orange 8, Acid Orange 10, Sunset Yellow, and Methyl Orange, with decolorization ratio up to 95% in 4 min; pH value was the key factor for degradation and H was one of the reactants; adsorption of azo dyes onto the material existed at the beginning but reduced gradually until disappearing completely. For the packed column system, 58%~90% of azo dyes were decomposed in the 1st circle of solution passing through the column, and the adsorption onto the materials could accelerate the degradation azo dyes with the increasing reaction time. During the degradation process, Fe2 , the product of NZVI, was exchanged to the resin again and could be reduced to Fe0 by KBH4 for reusing. The 10th refreshed NZVI possessed reductive activity up to 90% of the newly systhesized NZVI. Decomposing pollutants in the aqueous solution with columns packed with NZVI immobilized on the cation exchange resin is a promising technology that can solve the reclaiming and refreshing problem of NZVI.     

Copper(II) ion sensor based on electropolymerized undoped conducting polymers

A solid state copper(II) ion sensor is reported based on the application of electropolymerized undoped (neutral) polycarbazole (PCz) and polyindole (PIn) modified electrodes. The new sensor shows high selectivity to Cu²⁺ ions with a detection limit of 10^–5 M. PCz and PIn are formed respectively by the anodic oxidation of 50 mM carbazole and 5 mM indole monomers in dichloromethane containing 0.1 M tetrabutylammonium perchlorate on a platinum electrode using a single compartment cell. Potentiostatic polymerization of both the monomers are carried out at 1.3 V and 1.0 V vs. Ag/AgCl, respectively. Perchlorate ions were electrochemically removed from the polymer films by applying – 0.2 V vs. Ag/AgCl. Polymer-coated electrodes are incubated in 1 M KCl solution for 8 h followed by incubation in distilled water for 2 h before using as a metal ion sensor. The undoped PCz and PIn electrodes were found to be highly selective and sensitive for Cu²⁺ ions with little selectivity for Pb²⁺ and negligible response towards Ag⁺, Hg²⁺, Cu⁺, Ni²⁺, Co²⁺, Fe²⁺, Fe³⁺ or Zn²⁺. Potentiometric responses for Cu²⁺ ions are recorded for both the sensor electrodes together with a double-junction Ag/AgCl reference electrode. Calibration curves for Cu²⁺ are reported for both ion sensors. The polymer-modified electrodes were found to be stable for several weeks. Electronic Publication     

Progress of Organic Electrodes in Aqueous Electrolyte for Energy Storage and Conversion

Aqueous batteries using inorganic compounds as electrode materials are considered a promising solution for grid-scale energy storage, while wide application is limited by the short life and/or high cost of electrodes. Organics with carbonyl groups are being investigated as the alternative to inorganic electrode materials because they offer the advantages of tunable structures, renewability, and they are environmentally benign. Furthermore, the wide internal space of such organic materials enables flexible storage of various charged ions (for example, H⁺, Li⁺, Na⁺, K⁺, Zn²⁺, Mg²⁺, and Ca²⁺, and so on). We offer a comprehensive overview of the progress of organics containing carbonyls for energy storage and conversion in aqueous electrolytes, including applications in aqueous batteries as solid-state electrodes, in flow batteries as soluble redox species, and in water electrolysis as redox buffer electrodes. The advantages of organic electrodes are summarized, with a discussion of the challenges remaining for their practical application.     

Flow-injection spectrophotometric determination of arylamines and sulphonamides by diazotization and coupling in a micellar medium

In a sodium dodecyl sulphate (SDS) micellar solution, the rate of coupling of a diazonium ion with N-(1- naphthyl)ethylenediamine (NED) increases greatly, the protonation of the resulting azo dyes takes place at higher pH values and the dyes are more soluble. These favourable features were applied to the development of a simple flow-injection spectrophotometric procedure for the determination of diazotizable substances of pharmaceutical interest. Limits of detection in the range 0.2–0.5 μg ml^?1 (signal-to-noise ratio=3), with relative standard deviation of 0.7–3% (n=3) for 5 μg ml^?1 standards, were obtained.     

Removal of cationic dyes: basic magenta and methylene blue from aqueous solution by adsorption on modified loofah

Modified loofah was prepared by a simple chemical graft method to improve its adsorption for cationic dyes. Experimental results showed that the maximum amounts of basic magenta and methylene blue loaded on the modified loofah were 83.5 and 85.5 mg g^?1, and that on the unmodified loofah were 22.2 and 33.7 mg g^?1, respectively. The adsorption for both dyes could reach equilibrium after 300 min. A pseudo-second-order model is suitable for describing the adsorption and desorption kinetics of both dyes on the modified sorbent. According to the intra-particle diffusion model, sorption and desorption processes for the two dyes both presented two distinct phases and were mainly controlled by intra-particle diffusion. The dye-loaded modified loofah could be regenerated by using the mixture solution of HCl and ethanol (V_HCl:V_ethanol = 3:2) as eluent. Adsorption in the binary system showed that adsorption of the dyes was depressed by the presence of the other dye, and the two dyes could be removed efficiently when the initial concentrations were lower than 5.0 × 10^?5 mol L^?1. The Langmuir competitive model was suitable to predict the sorption isotherm in the binary system.     

Bismuth Film Electrode as an Alternative for Mercury Electrodes: Determination of Azo Dyes and Application for Detection in Food Stuffs

Bismuth electrodes were investigated and exhibit electrochemical properties similar to mercury electrodes but with much lower toxicity. An electrochemical application of bismuth film modified glassy carbon electrode for azo dyes determination was investigated. The plating step was optimized in order to achieve its analytical efficiency. A plating potential of ?0.9 V in a solution of 200 mg/L Bi(NO₃)₃, 0.5 M HNO₃ for 100 s yields to a suitable electrode (in terms of stability and detection). Azo dyes such as azorubine (i.e., carmoisine, E122), amaranth (E123), ponceau 4R (i.e., new coccine, E124) and allura red (E129) were determined by differential pulse voltammetry in a NaCl solution in the concentration range of few ppm to 100 ppm. The reproducibility of the signal, characterized by the relative standard deviation, was found to be less than 5%, the detection and quantification limits were few mg/L. The influence of other food components on the signal was studied and the applicability was tested on real beverages samples.