Determination of carbaryl by flow injection with luminol chemiluminescence inhibition detection

A flow-injection procedure is described for the determination of carbaryl based on its inhibition effect on luminol-cobalt(II) chemiluminescence reaction in alkaline medium in the presence of hydrogen peroxide. The calibration data over the range 5.0?×?10^?7 to 20?×?10^?6?M give a correlation coefficient (r ²) of 0.9972 with relative standard deviations (RSD; n?=?4) in the range of 1.0–2.1% with a limit of detection (3?×?blank noise) of 2.37?×?10^?7?M for carbaryl. The sample throughput was 120?h^?1. The effects of some carbamates, anions, and cations were studied on luminol CL system for carbaryl determination. The proposed method has been applied to determine carbaryl in natural waters.     

Determination of Two Pesticides in Soils by Dispersive Liquid–Liquid Microextraction Combined with LC-Fluorescence Detection

In the present work, a simple, rapid and sensitive sample pre-treatment technique, dispersive liquid–liquid microextraction (DLLME) coupled with liquid chromatography-fluorescence detection (LC-FLD), has been developed to determine carbamate (carbaryl) and organophosphorus (triazophos) pesticide residues in soil samples. Methanol was first used as extraction solvent for the extraction of pesticides from the soil samples and then as dispersive solvent in the DLLME procedure. Under the optimum extraction conditions, the linearity was obtained in the concentration range of 0.1–1,000 ng g^?1 for carbaryl and 1–5,000 ng g^?1 for triazophos, respectively. Correlation coefficients varied from 0.9997 to 0.9999. The limits of detection (LODs), based on signal-to-noise ratio (S/N) of 3, ranged from 14 to 110 pg g^?1. The relative standard deviation (RSDs, for 20.0 ng g^?1 of each pesticide) varied from 1.96 to 4.24% (n = 6). The relative recoveries of two pesticides from soil A1, A2 and A3 at spiking levels of 10.0, 20.0 and 50.0 ng g^?1 were in the range of 88.2–108.8%, 80.8–110.7% and 81.0–111.1%, respectively. The results demonstrated that DLLME was a sensitive and accurate method to determine the target pesticides, at trace levels, in soils.     

Flow-injection chemiluminescence determinations for human blood lead using controlled reagent release technology

A flow-through CL method for the determination of lead combined with controlled-reagent-release technology has been developed. Chemiluminescence (CL) reagents luminol and potassium permanganate were immobilized on anion exchange resin by electrostatic interaction. Lead ion was determined by its enhancing effect on the CL reaction between luminol and potassium permanganate. Both luminol and potassium permanganate were eluted from the anion exchange resin column by sodium phosphate solution. The linear range of the system was 10 μg mL^?1, and the detection limit was 5?×?10^–9 g mL^?1 lead (3σ). A complete analysis could be performed in 1 min with a relative SD 3.2% (1.0?×?10^–7 g mL^?1, n?=?9). The column shows remarkable stability and can be reused over 350 times and 21 days. The method has been applied to determine lead in human blood samples.     

The determination of platinum and palladium in rocks and soils by electrothermal atomic absorption spectrometry of extracts of their iodo complexes

The method developed for determining platinum and palladium in rocks and soils is based on extraction of iodo complexes of these elements into methyl isobutyl ketone (MIBK), followed by electrothermal atomic absorption spectrometry of the extracts. The limit of detection is 10 ng g^?1 for platinum and 3 ng g^?1 for palladium. Analysis of the standard noble metal ore PTC-1 with recommended values of 12.7 μg g^?1 for palladium and 3.0 μg g^?1 for platinum gave precisions of 4.4% and 5.6%, respectively, and deviations of 5.0% and 1.2% from the recommended values. The method is applicable to the determination of both elements in a wide variety of rocks and soils.     

An efficient and fast microwave-assisted extraction method developed for the simultaneous determination of 18 organochlorine pesticides in sediment

An efficient and fast microwave-assisted extraction (MAE) method followed by gas chromatographic separation with mass spectrometric detection (GC–MS) was developed for the extraction of 18 organochlorine pesticides (OCPs) from sediment. Parameters affecting the MAE procedure such as the type and volume of the extraction solvent, irradiation power, temperature and irradiation time were successfully optimised. Under the optimal conditions, extraction efficiencies in the range of 73.4–119% were obtained with THF–HEX (9:1, v/v) for all OCPs studied. The method was linear over the range of 2.9–5000 ng g^?1 with determination coefficients (r²) higher than 0.992 for all analytes. The limits of detection, LODs (S/N = 3), obtained varied from 1.0 to 2.2 ng g^?1 and limits of quantification, LOQs (S/N = 10) were between 2.9 and 6.8 ng g^?1. The proposed method was successfully applied to the analysis of real sediment samples and acceptable recoveries from 70.1 to 124% with RSDs ≤14.8% were obtained. 10 OCPs were determined below their LOQ and 8 OCPs in the range of 124–2830 ng g^?1. The MAE method was compared with Soxhlet, shake flask and ultrasonic solvent extraction techniques. Thus, the MAE–GC–MS method could efficiently be used for selective extraction and quantification of the target analytes from the complex sediment matrices.     

Flow-injection chemiluminescence determination of dihydralazine sulfate in serum using luminol and diperiodatocuprate (III) system

A novel flow-injection chemiluminescence (CL) method for the determination of dihydralazine sulfate (DHZS) is described. The method is based on the reaction of luminol and diperiodatocuprate (K₂[Cu(H₂IO₆)(OH)₂], DPC) in alkaline medium to emit CL, which is greatly enhanced by DHZS. The possible CL mechanism was first proposed based on the kinetic characteristic, CL spectrum and UV spectra. The optimum condition for the CL reaction was in detail studied using flow-injection system. The experiments indicated that under optimum condition, the CL intensity was linearly related to the concentration of DHZS in the range of 7.0 × 10^?9 to 8.6 × 10^?7 g mL^?1 with a detection limit (3σ) of 2.1 × 10^?9 g mL^?1. The proposed method had good reproducibility with the relative standard deviation 3.1% (n = 7) for 5.2 × 10^?8 g mL^?1 of DHZS. This method has the advantages of simple operation, fast response and high sensitivity. The special advantage of the system is that very low concentration of luminol can react with DPC catalyzed by DHZS to get excellent experiment results. And CL cannot be observed nearly when luminol with same concentration reacts with other oxidants, so luminol–DPC system has higher selectivity than other luminol CL systems. The method has been successfully applied to determine DHZS in serum.     

Determination of Total Chromium in Biological Samples by Automated Reagent Injection Chemiluminescence Analysis

A sensitive method for the determination of total chromium in real samples by flow injection–chemiluminescence (FI–CL) analysis was proposed. It was found that the CL intensity from luminol–lysozyme reaction could be markedly quenched, and the decrease of CL intensity was linear with the logarithm of Cr(III) concentrations over the range of 5.0 to 4000 pg mL^?1 with a detection limit of 2.0 pg mL^?1 (3σ) and relative standard deviations (RSDs) of 3.0, 2.6, and 2.0% for 10, 100, and 1000 pg mL^?1 Cr(III) (n = 7), respectively. At a flow rate of 2.0 mL min^?1, the whole process including sampling and washing could be accomplished within 36 s. The proposed CL method was successfully applied to the determination of total chromium in pharmaceutical capsules, a dietary supplement, and spiked human serum samples, with recoveries from 92.2 to 108.4% and RSDs of less than 4.0%. Using the homemade FI–CL model, the binding constant (K = 4.38 × 10⁶ L mol^?1) and the binding sites (n ≈ 1) of Cr(III) to lysozyme were given.     

A simple flow-injection chemiluminescence method for the determination of trace pentavalent vanadium in water samples

A simple method for rapid determination of trace pentavalent vanadium in natural water was presented by flow-injection chemiluminescence (CL). Through water injection, luminol and potassium permanganate were eluted from the anion exchange column to generate the CL, which was enhanced in the presence of V(V). Under the optimum conditions, the increased CL intensity was linear with V(V) concentration in the range from 0.1 to 100?ng?mL^?1. The limit of detection was 50?pg?mL^?1 (3σ) and the relative standard deviation (RSD) was 2.24% (n?=?5) for a 1.0?ng?mL^?1?V(V). At a flow rate of 2.0?mL?min^?1, one cycle of analysis could be performed in 0.5?min with a RSD of less than 3.0%. The proposed method was successfully applied to the determination of vanadium in natural water.     

In vitro monitoring of picogram levels of risperidone in human urine via luminollysozyme flow injection chemiluminescence

The anti-schizophrenic drug risperidone (RSP) exerts an inhibitory effect on the chemiluminescence (CL) of the luminol-lysozyme system. This finding forms the basis for a sensitive flow injection method for its determination at picogram levels. RSP binds to Trp62 in the lysozyme, and this leads to a conformational change upon which the CL of the system is quenched. The decrease in CL is proportional to the logarithm of the concentration of RSP, and the calibration graph is linear in the range from 0.1 pg?mL^?1 to 1.0 ng?mL^?1, with relative standard deviations of <5.0%, and a detection limit of 0.05 pg?mL^?1 (3σ). At a flow rate of 2.0 mL?min^?1, the whole process including sampling and washing is completed within 20 s. The method was successfully applied to monitoring RSP in human urine after incorporation of 2 mg of RSP, with a total excretion of 16.6% within 8.5 h.

Chemiluminescent Determination of Vitamin B12 Using Charge Coupled Device (CCD)

A method was developed for the determination of vitamin B₁₂ based on the enhancement of cobalt (II) on the chemiluminescence (CL) reaction between luminol and percarbonate (powerful source of hydrogen peroxide). The release of cobalt (II) from the vitamin B₁₂ was reached by a simple and fast microwave digestion (20 s microwave digestion time and a mix of nitric acid and hydrogen peroxide). A charge coupled device (CCD) photodetector, directly connected to the cell, coupled with a simple continuous flow system was used to obtain the full spectral characteristics of cobalt (II) catalyzed luminol-percarbonate reaction.

The optima experimental conditions were established: 8.0 m mol L^?1 luminol in a 0.075 mol L^?1 carbonate buffer (pH 10.0) and 0.15 mol L^?1 sodium percarbonate, in addition to others experimental parameters as 0.33 mL s^?1 flow rate and 2 s integration time, were the experimental conditions which proportionate the optimum CL emission intensity. The emission data were best fitted with a second-order calibration graph over the cobalt (II) concentration range from 4.00 to 300 µ g L^?1 (r² = 0.9990), with a detection limit of 0.42 µ g L^?1. The proposed method was successfully applied to the determination of vitamin B₁₂ in pharmaceuticals.     

On the Effect of Hydrogen Peroxide on the Flow‐Injection Determination of Platinum Based on Luminol Chemiluminescent Reaction

Abstract

A flow‐injection chemiluminescent (CL) method for the determination of trace amounts of Pt(IV) based on the oxidation reaction of luminol in alkaline solution is proposed. The effect of Pt(IV) on the oxidation of luminol was studied in the absence and in the presence of hydrogen peroxide. The positive effect of hydrogen peroxide as well as chloride ions on the sensitivity of measurements was observed. The developed method is characterized by a low limit of detection of Pt (LOD=0.06 ng mL^?1) and good reproducibility (RSD=2.2%). The addition of hydrogen peroxide to the reaction medium resulted in decreasing of platinum detection limit to 0.03 ng mL^?1.     

Multiresidue method for the determination of 32 human and veterinary pharmaceuticals in soil and sediment by pressurized-liquid extraction and LC-MS/MS

An analytical chemical method has been developed for the simultaneous determination of 32 different pharmaceuticals in soils and sediments. The pharmaceuticals cover a varity of different compound groups. Soil samples were extracted with different solvents with the help of pressurized-liquid extraction (PLE) followed by clean-up using a solid-phase extraction (SPE) procedure. The purified extracts were analyzed by LC-MS/MS. The extraction method was evaluated by testing the following variables: extraction solvents, solvent pH, and temperature. Applying 20 g of soil/sediment and extracting with a mixture of methanol with aqueous ammonia solution (0.1 mol L^?1) at 80?°C for 5 min in five cycles provided satisfactory recoveries between 66 and 114% with SD of between 1 and 14%. For preconcentration and purification tandem MAX-HLB cartridges were used. The volume and composition was optimized and the highest recoveries were obtained with a combination of methanol—aqueous ammonia solution. The limits of quantification (LOQs) were between 0.2 and 2 ng g^?1 and linearity higher than 0.98 for the majority of the selected pharmaceuticals. The method was successfully applied to soil samples collected from the Jerez de la Frontera agricultural region, irrigated with treated wastewater, and to sediment samples from the River Guadalete. The detection of nine pharmaceuticals including stimulants, antirheumatics, analgesics, anti-inflammatories, tranquilizers, and veterinary medicines at ng g^?1 concentration levels was achieved.     

On-Line Monitoring of Formaldehyde In Water and Air Using Chemiluminescence Detection

A rapid and sensitive chemiluminescence flow sensor for the determination of formaldehyde was proposed in this article. The analytical reagents involved in chemiluminescence (CL) reaction, luminol and KIO₄, were both immobilized on an anion-exchange column. The CL signal produced by the reaction between luminol and KIO₄, which were eluted from the column through water injection, was decreased in the presence of formaldehyde. Formaldehyde was sensed by measuring the decrement of CL intensity, which was observed linear over the logarithm of formaldehyde concentration range of 5.0-1000.0 ng mL^?1, and the limit of detection is 1.8 ng mL^?1 (3σ). At a flow rate of 2.0 mL min^?1, including sampling and washing, could be performed in 0.5 min with a relative standard deviation of less than 3.0%. The flow sensor offered reagentless procedures and remarkable stability in determination of formaldehyde, and could be easily re-used over 80 h. The proposed flow microsensor was applied successfully in the determination of formaldehyde in artificial water samples and air.     

Dispersive liquid-liquid microextraction of phenolic compounds using solidified floating organic droplets, and their determination by HPLC

We have developed a simple and efficient method for dispersive liquid-liquid microextraction of 4-nitrophenol, 2-naphthol and bisphenol A in real water samples. It is making use of solidified floating organic droplets of 1-dodecanol which has low density and a proper melting point. The type and volume of extraction solvent and dispersive solvent, the effect of salts, pH value and extraction time were optimized and resulted in enrichment factors of 84 for 4-nitrophenol, 123 for 2-naphthol, and 97 for bisphenol A. The limits of detection by HPLC are 1.50, 0.10 and 1.02 ng · mL^?1, respectively. Excellent linearity is observed in the concentration range from 10 to 800 ng · mL^?1, with coefficients of correlation ranging from 0.9988 to 0.9999. The relative standard deviations (for n?=?5) are from 3.2 to 5.3 %, and relative recoveries for the three phenols in tap, river and spring water range from 85.0 to 105.0 %, 98.3 to 110.0 %, and 98.6 to 109.0 %, respectively.

Determination of some carbamate pesticides in watermelon and tomato samples by dispersive liquid–liquid microextraction combined with high performance liquid chromatography

A novel method for the determination of five carbamate pesticides (metolcarb, carbofuran, carbaryl, isoprocard and diethofencard) in watermelon and tomato samples was developed by dispersive liquid–liquid microextraction (DLLME) coupled with high performance liquid chromatography-diode array detection (HPLC-DAD). Some experimental parameters that influence the extraction efficiency were studied and optimised to obtain the best extraction results. Under the optimum conditions for the method, the calibration curve was linear in the concentration range from 10 to 1000?ng?g^?1 for all the five carbamate pesticides, with the correlation coefficients (r) varying from 0.9982 to 0.9992. Good enrichment factors were achieved ranging between 80 and 177, depending on the compound. The limits of detection (LODs) (S/N?=?3) were ranged from 0.5 to 1.5?ng?g^?1. The method has been successfully applied to the analysis of the pesticide residues in watermelon and tomato samples. The recoveries of the method fell in the range between 76.2% to 94.5% with RSDs less than 9.6%, indicating the feasibility of the DLLME method for the determination of the five carbamate pesticides in watermelon and tomato samples.     

Determination of Two Pesticides in Soils by Dispersive Liquid–Liquid Microextraction Combined with LC-Fluorescence Detection

In the present work, a simple, rapid and sensitive sample pre-treatment technique, dispersive liquid–liquid microextraction (DLLME) coupled with liquid chromatography-fluorescence detection (LC-FLD), has been developed to determine carbamate (carbaryl) and organophosphorus (triazophos) pesticide residues in soil samples. Methanol was first used as extraction solvent for the extraction of pesticides from the soil samples and then as dispersive solvent in the DLLME procedure. Under the optimum extraction conditions, the linearity was obtained in the concentration range of 0.1–1,000 ng g⁻¹ for carbaryl and 1–5,000 ng g⁻¹ for triazophos, respectively. Correlation coefficients varied from 0.9997 to 0.9999. The limits of detection (LODs), based on signal-to-noise ratio (S/N) of 3, ranged from 14 to 110 pg g⁻¹. The relative standard deviation (RSDs, for 20.0 ng g⁻¹ of each pesticide) varied from 1.96 to 4.24% (n = 6). The relative recoveries of two pesticides from soil A1, A2 and A3 at spiking levels of 10.0, 20.0 and 50.0 ng g⁻¹ were in the range of 88.2–108.8%, 80.8–110.7% and 81.0–111.1%, respectively. The results demonstrated that DLLME was a sensitive and accurate method to determine the target pesticides, at trace levels, in soils.

     

Chemiluminometric Determination of the Pesticide Pirimicarb by a Flow Injection Analysis Assembly

Abstract

A flow injection (FI) method is described for the determination of pirimicarb. It was found that an enhanced chemiluminescence (CL) signal is obtained when employing the luminol–H₂O₂–horseradish peroxidase (HRP) system. Under the optimum experimental conditions, the enhanced CL intensity was linear with the concentration 4.25–30.75 ng mL^?1 (r = 0.997, n = 8) with a relative standard deviation of 0.99%, containing 12.75 ng mL^?1 (n = 8). The limit of detection of the investigated compound was 0.12 ng mL^?1. The method shows a moderate selectivity against other pesticides (Amitrole, Atrazine, 2,4,5-T, Dichlorprop, and Metamidophos).The proposed method was sensitive, simple, rapid, and successfully applied to the determination of pirimicarb when it is applied in freshwater; the mean recoveries were 98.3–118.5%.     

Validation of a novel derivatization method for GC–ECD determination of acrylamide in food

This paper proposes a new method for quantitative analysis of acrylamide in cereal-based foods and potato chips. The method uses reaction with trifluoroacetic anhydride, and analyses the resulting derivative by use of gas chromatography with electron-capture detection (GC–ECD). The effects of derivatization conditions, including temperature, reaction time, and catalyst, on the acylation reaction were evaluated. Chromatographic analysis was performed on an SE-54 capillary column. Under the optimum conditions, good retention and peak response were achieved for the acrylamide derivative. The analytical method was fully validated by assessment of LODs and LOQs (1 ng g^?1 and 25 ng g^?1, with relative standard deviations (RSD) 2.1 and 3.6, respectively), linearity (R?=?0.9935 over the range 0.03–10 μg g^?1), and extraction recovery (>96 %, with RSD below 2.0, for acrylamide spiked at 1, 20, 50, and 100 ng g^?1; 99.8 % for acrylamide content >1000 ng g^?1). The method requires no clean-up of the acrylamide derivative before injection. The method has been successfully used to determine acrylamide levels in different commercial cereal-based foods, French fries, and potato chips.

Sensitive Determination of Nanogram Levels of Diacerein in a Pharmaceutical Formulation by Flow Injection Chemiluminescence Analysis

A simple, sensitive and inexpensive flow injection chemiluminescence (FI‐CL) method for the determination of diacerein was proposed. It was based on the greatly enhancive effect of diacerein on the CL reaction between luminol and hydrogen peroxide in alkaline medium. The enhanced CL intensity was linear with the concentration of diacerein over the range 1.0–500 ng/mL with a detection limit (3σ) of 0.2 ng/mL. The relative standard deviation was 1.1% (n = 8, 20 ng/mL diacerein) and the sample throughput was about 120 samples h^?1. This simple method has been successfully applied for the determination of diacerein in a pharmaceutical formulation without interference from its potential impurities. The degradation of diacerein was also investigated briefly.     

High-accuracy differential-pulse anodic stripping voltammetry with indium as an internal standard

Indium(III) is used as an internal standard for the determination of cadmium, copper and lead at the 20 ng g^?1 level by using differential-pulse anodic stripping voltammetry; the supporting electrolyte is 1.0 mol l^?1 ammonium bromide/0.25 mol l^?1 nitric acid. For each solution, each stripping peak of interest is normalized to the corresponding peak height obtained in the same voltammogram for a known, added concentration of indium(III). A calibration curve is prepared for each element by using these normalized peak heights. The technique is demonstrated for NBS SRM 1643b (Trace Elements in Water). The relative standard deviations for six independent determinations of Cd, Cu, and Pb at the 20 ng g^?1 level are 1.9%, 5.4%, and 1.2%, respectively. The imprecision for copper is limited by the sloping baseline at its stripping potential. The detection limit for each element is less than 1 ng g^?1.