Cloud point extraction for the determination of cadmium and lead employing sequential multi-element flame atomic absorption spectrometry

A cloud point extraction procedure for pre-concentration and determination of cadmium and lead in drinking water using sequential multi-element flame atomic absorption spectrometry is described. 4-(2-thiazolylazo)-orcinol (TAO) has been used as complexing agent and the micellar phase was obtained using the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) and centrifugation. The conditions for reaction and extraction (surfactant concentration, reagent concentration, effect of incubation time, etc) were studied and the analytical characteristics of the method were determined. The method allows the determination of cadmium and lead with quantification limits of 0.30?µg?L^?1 and 2.6?µg?L^?1, respectively. A precision expressed as relative standard deviation (RSD, n?=?10) of 2.3% and 2.6% has been obtained for cadmium concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively, and RSD of 1.3% and 1.7% for lead concentrations of 10?µg?L^?1 and 30?µg?L^?1, respectively. The accuracy was confirmed by analysis of a natural water certified reference material. The method has been applied for the determination of cadmium and lead in drinking water samples collected in the cities of Ilhéus and Itabuna, Brazil. Recovery tests have also been performed for some samples, and results varied from 96 to 105% for cadmium and 97 to 106% for lead. The cadmium and lead concentrations found in these samples were always lower than the permissible maximum levels stipulated by World Health Organization and the Brazilian Government.     

An Ionic Liquid Loaded β-Cyclodextrin-Cross-Linked Polymer as the Solid Phase Extraction Material Coupled with High-Performance Liquid Chromatography for the Determination of Rhodamine B in Food

A novel method for separation and determination of rhodamine B in food samples is described. The work is based on the utilization of an ionic liquid loaded β-cyclodextrin cross-linked polymer coupled with high-performance liquid chromatography for the determination of rhodamine B. The inclusion interaction of the ionic liquid-β-cyclodextrin cross-linked polymer with rhodamine B was studied by FTIR. Under optimum conditions, the preconcentration factor achieved for this method was approximately 20. The linear range, detection limit, and relative standard deviation were 0.80 to 130.0 µg L^?1, 0.09 µg L^?1, and 0.66% (n = 3, concentration = 10.0 µg L^?1), respectively. The technique was successfully applied for determination of rhodamine B in food samples.     

Sensitive electrochemical detection of picloram utilising a multi-walled carbon nanotube/Cr-based metal-organic framework composite-modified glassy carbon electrode

This study describes the utilisation of a glassy carbon electrode modified with a composite of multi-walled carbon nanotube and Cr-based metal-organic framework (MIL-101, Cr-BDC, BDC = 1,4-benzenedicarboxylate) for the sensitive, simple and fast voltammetric determination of picloram in environmental samples. Under optimum conditions, additions of picloram using square wave voltammetry showed linear ranges of picloram concentrations from 24.15 to 3018 µg?L^?1 (0.1–12.5 μM) and from 3018 to 9658 µg?L^?1 (12.5–40 μM) with a detection limit of 14.49 µg?L^?1 (0.06 µM). The method was successfully applied to the determination of picloram in tap and river water samples spiked with picloram without any purification step by the standard addition method. The good recovery values obtained ranging from 97.5% to 105.0% revealed the reliability and accuracy of the method.     

Spectrophotometric Determination of Bromate in Water Using Multisyringe Flow Injection Analysis

A multisyringe flow injection system for the spectrophotometric determination of bromate in water is proposed, based on the oxidation of phenothiazine compounds by bromate in acidic medium. Several phenothiazines were tested, including chlorpromazine, trifluoperazine, and thioridazine. Higher sensitivity and lower LOD were attained for chlorpromazine. Interference from nitrite, hypochlorite, and chlorite was eliminated in-line, without any changes in the manifold. The automatic methodology using chlorpromazine allowed the determination of bromate between 25 and 750 µg L^?1, with LOD of 6 µg L^?1, good precision (RSD < 1.6%, n = 10), and determination frequency of 35 h^?1.     

Dabsyl chloride derivatisation of melamine followed by high-performance liquid chromatography determination in water samples

A new and sensitive precolumn derivatisation with dabsyl chloride was developed for the analysis of melamine in water samples by high-performance liquid chromatography (HPLC) with visible detection. Derivatisation with dabsyl chloride leads to improving sensitivity and hydrophobicity of melamine. Under optimum conditions of derivatisation and microextraction, the method yielded a linear calibration curve ranging from 10 to 2000 µg L^?1 with a determination coefficient (R²) of 0.9952. Limit of detection (LOD) and limit of quantification (LOQ) were 2.0 and 6.0 µg L^?1, respectively. The relative standard deviation per cent (RSD%) for intraday and inter-day extraction and determination at 20 and 200 µg L^?1 levels of melamine was less than 8.2% (n = 6). Finally, the proposed method was successfully applied for the determination of melamine in different water samples and satisfactory results were obtained (relative recovery ≥91%).     

Supramolecular dispersive liquid–liquid microextraction-based solidification of floating organic drops combined with electrothermal atomic absorption spectrometry for determination of chromium species

A simple, sensitive and reliable method has been developed for separation and preconcentration of chromium (VI) from aqueous samples before determination by electrothermal atomic absorption spectrometry. The method is based on the extraction of the hydrophobic complex of chromium (VI) with ammonium pyrrolidine dithiocarbamate in the coacervates made up of decanoic acid reverse micelles in the water–tetrahydrofuran mixture. Parameters affecting the extraction efficiency of the analyte were studied and optimised. Under the optimum conditions, the linear range, enhancement factor, the limit of detection and limit of quantification were found to be 0.008–0.4 µg L^?1, 127, and 1.8 ng L^?1 and 6.0 ng L^?1, of Cr(VI), respectively. The relative standard deviation at the concentration level of 0.1 µg L^?1 Cr(VI) (n = 6) was 4.2%. Total chromium was determined after the oxidation of Cr(III) to Cr(VI) with permanganate in acidic medium. The method was successfully applied to the determination of chromium species in water and human serum samples.     

A novel,simple and robust method for the analysis of sulfonamides in fish farming water samples using column switching liquid chromatography

A novel method for the online extraction and preconcentration of four sulfonamides was developed using column switching liquid chromatography. Sulfadiazine, sulfathiazole, sulfamethoxypyridazine and sulfamethoxazole were analysed in water samples and preconcentrated in a C18 guard column. Suitable validation parameters were obtained, such as precision, accuracy and relative recovery, in accordance with the validation guidelines of the Food and Drug Administration. Low limits of detection (0.05–0.09 µg L^?1) and quantification (0.30 µg L^?1, for all of them) were obtained. The quadratic polynomial model was used to adjust the calibration data, and the coefficients of determination were higher than 0.999 for all the analytes. The method was shown to be robust to the assayed parameters according to Youden’s test. The proposed method was successfully used to determine sulfonamides in 11 different fish farming water samples, in which sulfadiazine (0.732 µg L^?1), sulfamethoxazole (0.531 µg L^?1), sulfathiazole (0.546–1.856 µg L^?1) and sulfamethoxypyridazine (0.369–1.509 µg L^?1) were found.     

Development of carbon paste electrode modified with cadmium ion-imprinted polymer for selective voltammetric determination of Cd2+

A simple and fast voltammetric method based on a new electrode composed of carbon paste electrode/bifunctional hybrid ion imprinted polymer (CPE/IIP) was developed for the quantification of Cd²⁺ in water samples. The voltammetric measurements by Differential Pulse Voltammetry were performed by using CPE containing 11.0 mg of IIP under phosphate buffer solution at concentration 0.1 mol L^?1 and pH 6.5. The electrochemical method was carried out by Cd²⁺ preconcentration at ?1.2 V during 210 s, followed by anodic stripping. The performance of IIP towards Cd²⁺ determination was evaluated by comparison to non-imprinted polymer, whose detectability of IIP was much higher (45%). The sensitivity of the sensor was found to be 0.0105 µA/µg L^?1. The limits of detection and limits of quantification were found to be 4.95 μg L^?1 and 16.4 μg L^?1, respectively. The developed method was successfully applied to Cd²⁺ determination in mineral, tap and lake water samples, whose results are in agreement with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) used as reference analytical technique. According to achieved results, the developed method can be used for routine analysis of quality control of water samples from different sources.     

Selective Determination of Copper in Water Samples by Atomic Absorption Spectrometry after Cloud Point Extraction

A preconcentration methodology utilizing the cloud point phenomenon is described for the determination of copper by flame atomic absorption spectrometry. The reagent Sulfathiazolylazo resorsin was used as a complexing agent. The preconcentration factor of 25-fold was obtained. The calibration curve is linear in the range of 4–400 µ g L^?1 with a limit of detection of 0.64 µ g L^?1. The relative standard deviation (n = 5, 12 µ g L^?1) was 3.5%. The cloud point is formed in the presence of phenol at room temperature. The method was successfully applied to the determination of copper in water samples and a standard reference material.     

Determination of antimony(III) and (V) in natural water by cathodic stripping voltammetry with in-situ plated bismuth film electrode

A method is described for the sequential determination of Sb(III) and Sb(V) using Osteryoung square wave cathodic stripping voltammetry. It employs an in-situ plated bismuth-film on an edge-plane graphite substrate as the working electrode. Selective electro-deposition of Sb(III)/Sb(V) is accomplished by applying a potential of ?500 mV vs. Ag/AgCl, followed by reduction to stibine at a more negative potential in the stripping step. Stripping was carried out by applying a square wave waveform between ?500 and ?1400 mV to the antimony deposited. The stripping peak current at ?1150 mV is directly proportional to the concentration of Sb( III)/Sb(V). The calibration plots for Sb (III) were linear up to 12.0?µg L^?1 depending on the time of deposition. The calibration plots for Sb (V) were linear up to 7.0?µg L^?1, also depending on the time of deposition. The relative standard deviation in the determination of 0.1?µg L^?1 of Sb(III) is 4.0% (n?=?5), and the limit of detection is as low as 2 ng L^?1. In case of 0.1?µg L^?1 Sb(V), the relative standard deviation is 3.0% (n?=?5) and the detection limit also is 2 ng L^?1. The method was applied to the analysis of river and sea water samples.     

Application of bar adsorptive microextraction to determine trace organic micro-pollutants in environmental water matrices

The present work proposes the application of bar adsorptive micro-extraction (BAµE) coated with an N-vinylpyrrolidone polymer (NVP) combined with micro-liquid desorption (200 µL) followed by high-performance liquid chromatography with diode array detection (BAµE(NVP)-µLD/HPLC-DAD) for the determination of trace levels of emerging organic micro-pollutants in environmental water matrices. The model compounds selected include an antibacterial/antifungal agent (triclosan), two pharmaceuticals (carbamazepine and diclofenac) and two steroid hormones (17α-ethinylestradiol and 17β-estradiol), in which the latter three were recently included in the European Union watch list of substances to be monitored in the field of water policy. Assays performed on 25 mL of ultrapure water samples spiked at the 8.0 µg L^?1 level yielded average recoveries ranging from 81.9 to 102.4% for the compounds studied using optimised experimental conditions. The proposed analytical methodology demonstrated suitable detection limits (0.02–0.10 µg L^?1) and good linear dynamic ranges (0.1–20.0 µg L^?1) with determination coefficients higher than 0.9909. Using the standard addition method (SAM), the present analytical approach was applied on environmental water matrices, including surface, sea, river and groundwaters. The proposed method proved to be a suitable and alternative sorption-based static micro-extraction technique for monitoring trace levels of organic micro-pollutants in environmental water matrices.     

Increased Sensitivity Spectrophotometric Flow Analysis Method for Copper Determination in Water Samples

A reverse configured flow injection system was developed for the determination of copper in water samples. In this study, a bathocuproine disulfonic acid copper complexing reagent was used. In the presence of a reducing agent (hydroxylamine), the formation of complex was monitored at 484 nm. The determination range extended from 1 to 40 µg L^?1, with an applicable determination rate of 40 h^?1. The developed method was applied to the determination of copper in water samples (estuarine, river, and drinking water) and showed good accuracy (z-score below 2). The detection limit of 0.7 µg L^?1 copper is consistent with the requirement of the target water samples. The developed method was also used for the comparison of different spectrophotometric flow cells. Alternative flow cells (U, Z shaped, and the liquid waveguide capillary cell) were compared in terms of their sensitivity and response to refractive index changes.     

Simultaneous spectrophotometric determination of iron species using orthogonal signal correction–generalized partial least squares calibration method after vortex-assisted dispersive liquid–liquid microextraction

A vortex-assisted dispersive liquid–liquid microextraction method in combination with UV–Vis spectrophotometry was developed for the simultaneous extraction and determination of iron species. In this method, Fe²⁺ and Fe³⁺ were complexed with pyridine-2-amidoxime, neutralized through ion pair formation with sodium dodecyl sulfate, and extracted into the fine droplets of chloroform. After centrifugation, the absorbance of the extracted complexes was recorded in the wavelength range of 360–700 nm. The parameters affecting the extraction efficiency such as the pH, the type and volume of the extraction solvent, ligand concentration, and sample volume were optimized. The individual iron species was then determined by means of the orthogonal signal correction–generalized partial least squares method. Under the optimized conditions, the calibration curves were linear over the range of 2.0–100 and 3.0–200 µg L^?1 with detection limits of 0.4 µg L^?1 for Fe²⁺ and 0.8 µg L^?1 for Fe³⁺, respectively. The relative standard deviations for intra- and inter-day assays (n = 5) were 2.3 and 4.0 for Fe²⁺ at 50 µg L^?1 and 2.7 and 4.3 for Fe³⁺ at 30 µg L^?1, respectively. The enhancement factors of 77 and 69 were achieved for Fe²⁺ and Fe³⁺, respectively. The proposed method was successfully applied to the determination of iron species in water samples.     

Ionic liquid-modified silica-coated magnetic nanoparticles; promising anion-exchange sorbent for extraction of Cr(VI)

In the present study, ionic liquid-modified silica-coated magnetic nanoparticles (MNPs) were synthesised and applied as a new anion-exchange sorbent for extraction and determination of Cr(VI) followed by inductively coupled plasma atomic emission spectrometry. The characterisation of MNPs was carried out by scanning electron microscope, Fourier transform infrared and vibrating sample magnetometer. Experimental design and response surface methodology were used for optimisation of different parameters which affect extraction efficiency of Cr(VI). Under the optimised conditions, extraction recoveries within the range of 25–33% with relative standard deviations (RSD%, n = 4) within the range of 3.0–5.0% were obtained. The limit of detection was found to be 0.1 µg L^?1. The linearity was studied in the range of 0.5-200 µg L^?1 with the determination coefficient of 0.9958. Also, calculated Errors% for determination of Cr(VI) in the range of 5-15 depict that the method offers acceptable accuracy for analysis of Cr(VI). The method was successfully applied for extraction and determination of Cr(VI) selectively in some tannery waste water samples.     

Ligandless-ultrasound-assisted emulsification microextraction followed by inductively coupled plasma-optical emission spectrometry for simultaneous determination of heavy metals in water samples

In this study, a simple and efficient method of ligandless-ultrasound-assisted emulsification microextraction (LL-USAEME) followed by inductively coupled plasma-optical emission spectrometry (ICP-OES) has been developed for simultaneous extraction, preconcentration and determination of manganese, cadmium, cobalt and nickel in water samples. In the proposed approach, tetrachloroethylene was selected as extraction solvent. The effect of important experimental factors such as volume of extraction solvent, pH, sonication time, salt concentration, and temperature was investigated by using a fractional factorial design (2^5?1) to identify important factors and their interactions. In the next step, a Box-Behnken design (BBD) was applied for optimisation of significant factors. The obtained optimal conditions were: 30?µL for extraction solvent, 12 for pH, 5?min for sonication time, and 5% w/v for salt concentration. The limits of detections (LODs) for Cd(II), Co(II), Mn(II) and Ni(II) were 0.20, 0.13, 0.21 and 0.28?µg?L^?1, respectively. Relative standard deviations (RSD, C?=?200.0?µg?L^?1, n?=?9) were between 3.4–7.5% and the calibration graphs were linear in the range of 0.25 to 1000.0?µg?L^?1 for Mn, 0.5–1000.0?µg?L^?1 for Co and Ni and 1.0–250.0?µg?L^?1 for Cd. The determination coefficients (R ²) of the calibration curves for the analytes were in the range of 0.993 to 0.999. The proposed method was validated by using two certified reference materials, and also the method was applied successfully for the determination of heavy metals in different real water samples.     

Preconcentration of trace amounts of cobalt (II) ions in water and agricultural products samples using of 5-(4-dimethylaminobenzylidene) rhodanin modified SBA-15 sorbent prior to FAAS determination

In the present study, the ?5-(4-dimethylaminobenzylidene)rhodanin-modified SBA-15? was applied as stable solid sorbent for the separation and preconcentration of trace amounts of cobalt ions in aqueous solution. SBA-15 was modified by ?5-(4-dimethylaminobenzylidene)rhodanin reagent. The sorption of Co²⁺ ions was done onto modified sorbent in the pH range of 6.8–7.9 and desorption occurred in 5.0 mL of 3.0 mol L^?1 HNO₃. The results exhibit a linear dynamic range from 0.01 to 6.0 mg L^?1 for cobalt. Intra-day (repeatability) and inter-day (reproducibility) for 10 replicated determination of 0.06 mg L^?1 of cobalt was ±1.82% and ?±1.97%?. Detection limit was 4.2 µg L^?1 (3S_b, n = 5) and preconcentration factor was 80. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type and interference ions were studied for the preconcentration of Co²⁺. The proposed method was applied for the determination of cobalt in standard samples, water samples and agricultural products.     

Determination of phosphate in freshwater samples by flow-injection with lucigenin chemiluminescence

Lucigenin chemiluminescence (CL) in conjunction with flow-injection analysis (FIA) is used for the determination of phosphate in freshwater samples. The procedure is based on the formation of molybdophosphoric heteropoly acid (MoP–HPA) by the reaction of phosphate and ammonium molybdate under acidic conditions. CL emission was observed as a result of oxidation of lucigenin in aqueous sodium hydroxide solution in the presence of MoP–HPA. Calibration was linear up to 500?µg?L^?1 (r ^2?=?0.9998; n?=?8), with a detection limit (S/N?=?3) of 0.95?µg?L^?1. An injection throughput of 120 h^?1, and relative standard deviation (RSD; n?=?4) of 1.3–3.2% were achieved in the concentration range studied. An on-line chelating column was used to remove interfering cations. The method was applied to freshwater samples, and the results (51?±?1.0 – 107?±?2.0?µg?L^?1) did not differ significantly from results obtained using a spectrophotometric method (52.5?±?1.0 – 102?±?2.0?µg?L^?1) at 95% confidence level (t-test).     

Large‐volume sample stacking with polarity switching for analysis of azo dyes in water samples by capillary electrophoresis

ABSTRACT

A simple, fast and efficient on-line pre-concentration method (large-volume sample stacking) by capillary electrophoresis was proposed for determination of azo dyes residues (allura red [AR], sunset yellow [SY] and tartrazine [TAR]) in water samples. Pre-concentration variables involved in the system were optimised using of a Box–Bhenken design. Under the optimal conditions: injection time 150.0 s, pre-concentration time 120.0 s and reverse potential ?8.0 kV, the proposed methodology improved the analytical sensibility achieving limits of detection of 21.0–41.4 µg L^?1 with enrichment factors of 82.1–210.8 fold. The large-volume sample stacking-capillary electrophoresis method was validated and applied to determine azo dyes residues in 20 water samples (bottled, spring and tap water). Two samples were positive for sunset yellow and tartrazine with a concentration of 25.3 and 30.2 µg L^?1 and % RSD less than 10.0% in all cases.     

On-line simultaneous pre-concentration procedure for the determination of cadmium and lead in drinking water employing sequential multi-element flame atomic absorption spectrometry

An on-line pre-concentration system for the sequential determination of cadmium and lead in drinking water by using fast sequential flame atomic absorption spectrometry (FS-FAAS) is proposed in this paper. Two minicolums of polyurethane foam loaded with 2-(6-methyl-2-benzothiazolylazo)-orcinol (Me-BTAO) were used as sorptive pre-concentration media for cadmium and lead. The analytical procedure involves the quantitative uptake of both analyte species by on-column chelation with Me-BTAO during sample loading followed by sequential elution of the analytes with 1.0?mol?L^?1 hydrochloric acid and determination by FS-FAAS. The optimisation of the entire analytical procedure was performed using a Box–Behnken multivariate design utilising the sampling flow rate, sample pH and buffer concentration as experimental variables.

The proposed flow-based method featured detection limits (3σ) of 0.08 and 0.51?µg?L^?1 for cadmium and lead, respectively, precision expressed as relative standard deviation (RSD) of 1.63% and 3.87% (n?=?7) for cadmium at the 2.0?µg?L^?1 and 10.0?µg?L^?1 levels, respectively, and RSD of 6.34% and 3.26% (n?=?7) for lead at the 5.0?µg?L^?1 and 30.0?µg?L^?1 levels, respectively. The enrichment factors achieved were 38.6 and 30.0 for cadmium and lead, respectively, using a sample volume of 10.0?mL. The sampling frequency was 45 samples per hour. The accuracy was confirmed by analysis of a certified reference material, namely, SRM 1643d (Trace elements in natural water). The optimised method was applied to the determination of cadmium and lead in drinking water samples collected in Santo Amaro da Purificação City, Bahia, Brazil.     

Flow-Injection Determination of Iron Based on Its Catalysis on the Oxidation Reaction of Xylenol Orange by Potassium Bromate

A flow injection system is proposed for catalytic kinetic spectrophotometric determination of trace iron(II + III). The involved reaction is based on the catalytic effect of iron(III) on oxidation reaction of xylenol orange by potassium bromate to form a blue-violet complex. Iron(II) is also determined, being oxidized to iron(III) by potassium bromate. The calibration graph is linear in the range of 0.02–10.0 µg l^?1 and 10.0–1100 µg l^?1. The relative standard deviation is 1.5% for 4.0 µg l^?1 iron(III) and 2.3% for 60.0µg l^?1 iron(III) (n = 11). The presented system was applied successfully to the determination of iron in natural waters.