Thermogravimetric analysis and differential scanning calorimetric studies on nanoclay-filled TPU/PP blends

Thermal stability of ester-thermoplastic polyurethane (TPU)/polypropylene (PP) and ether-TPU/PP blends was evaluated by thermogravimetric studies. Thermal studies were made as a function of blend ratio. Effects of compatibilization using MA-g-PP and nanoclay addition on thermal stability were evaluated. Mass loss at 400 °C was found to decrease with increasing PP content were determined. Finally the compatibility and crystallization behavior of the blends were studied by differential scanning calorimetry. Compared to the ether-TPU blend nanocomposites, the ester-TPU blends showed better compatibility and thermal stability.     

Biodegradable polyester/modified mesoporous silica composites for effective bone repair with self‐reinforced properties

A series novel composites based on poly(_L‐lactide) (PLLA) oligomer modified mesoporous silica (MCM41) homogeneous dispersed into poly(_L‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer has been successfully prepared. The structure of PLTG terpolymer was characterized by ¹H NMR. The structure and properties of modified and unmodified MCM41 were attested by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyzer (TGA), X‐ray diffraction (XRD), N₂ adsorption–desorption, scanning electron microscope (SEM), and transmission electron microscope (TEM), which demonstrated that the MCM41 was successfully grafted by the PLLA oligomer. The effect of different concentration of modified MCM41 in PLTG matrix on thermal properties, mechanical properties, and hydrophilicity was investigated by TGA, differential scanning calorimetry (DSC), mechanical testing, contact angle measurement, and SEM. The results of mechanical tests showed that 5 wt% of modified MCM41 nanoparticles gave rise to optimal reinforcing effect. The tensile strength, Young's modulus, and elongation at break of the PLTG/PLLA‐MCM41 (5%) composites were 33.2 Mpa, 1.58 Gpa, and 268.7%, respectively, which were all higher than the PLTG/MCM41 (5%) composites and pristine PLTG matrix, which were due to good interfacial adhesion between the PLTG matrix and MCM41 nanoparticles. TGA and DSC have shown that 5% modified MCM41 in the PLTG increased the temperature of composite degradation and T_g. Water contact angle measurement showed the hydrophilicity of the composites increases with the increase of modified MCM41 content. The live/dead assay showed that the modified MCM41 existing on the PLTG matrix presents very excellent cytocompatibility. Therefore, the novel composite material represents promising way for bone tissue engineering application.     

The β-nucleated ternary composites of polypropylene/nano-CaCO3/short poly(ethylene-terephthalate) fiber

A serial of β-nucleated polypropylene (β-PP)/nano-calcium carbonate (nano-CaCO₃)/ short poly(ethylene-terephthalate) (PET) fiber composites were prepared using extrusion blending. Maleic anhydride grafted PP (PP-g-MA) was used to modify the compatibility. The relationships among components, structure, and properties of the PP composites were studied. The results show that adding nano-CaCO₃ improved the mechanical properties of the materials. Adding PET fiber increased the rigidity and toughness but the tensile strength decreased. PP-g-MA modified the compatibility of the components of the composites. Both PET fiber and nano-CaCO₃ had nucleation effect on the PP crystallization and slightly induced the formation of β crystals. Ternary β-PP/nano-CaCO₃/PET fiber composites contained high β-crystal content, and the compatibilizer exhibited synergy effect with β nucleating agent to further increase the β-crystal content in the blends. Mo’s method could satisfactorily describe the nonisothermal crystallization behavior of ternary composites, whereas Jeziorny and Ozawa methods failed to do the same ideally.     

Synergistic effects of β‐cyclodextrin containing silicone oligomer on intumescent flame retardant polypropylene system

The effects of β‐cyclodextrin containing silicone oligomer(CDS), as a synergistic agent, on the flame retardancy and mechanical properties of intumescent flame retardant polypropylene composites were studied by adding different amounts of CDS in intumescent flame retardants. The limiting oxygen index (LOI), UL‐94 test, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) were utilized to evaluate the synergistic effects of CDS in the composites. It was found that after a little amount of CDS partially replaced a charring‐foaming agent (CFA) in IFR, LOI values of the composites were enhanced and they obtained a UL‐94 V‐0 rating. IFR system containing 6.25wt% CDS presented the best flame retardancy in PP. The experimental results obtained from LOI and UL‐94, TGA, SEM, and mechanical properties indicated that the combination of CDS and CFA presents synergistic effects in flame retardancy, char formation, and mechanical properties of the composites. This is probably due to different structures of polyhydroxyl macromolecules (CDS and CFA), the existence of dimethyl silicone group in CDS, and the toughness of epoxy silicon chain in CDS. SEM results proved that the interfacial compatibility between IFR and PP was improved by CDS. Copyright © 2009 John Wiley & Sons, Ltd.     

Simultaneously improving the tensile and impact properties of isotactic polypropylene with the cooperation of <Emphasis Type="Italic">co</Emphasis>-PP and <Emphasis Type="Italic">β</Emphasis>-nucleating agent through pressure vibration injection molding

In this article, crystalline morphology and molecular orientation of isotactic polypropylene (iPP), random copolymerized polypropylene (co-PP) and β-nucleating agent (β-NA) composites prepared by pressure vibration injection molding (PVIM) have been investigated via polarized light microscopy, scanning electron microscopy, wide-angle X-ray diffraction and differential scanning calorimetry. Results demonstrated that the interaction between co-PP and iPP molecular chains was beneficial for the mechanical improvement and the introduction of β-NA further improved the toughness of iPP. In addition, after applying the pressure vibration injection molding (PVIM) technology, the shear layer thickness increased remarkably and the tensile strength improved consequently. Thus, the strength and toughness of iPP/co-PP/β-NA composites prepared by PVIM were simultaneously improved compared to those of the pure iPP prepared by conventional injection molding (CIM): the impact toughness was increased by five times and tensile strength was increased by 9 MPa. This work provided a new method to further enhance the properties of iPP/co-PP composites through dynamic processing strategy.     

Intumescent flame retardation and silane crosslinking of PP/EPDM elastomer

This study deals with the silane crosslinking and intumescent flame retardation of polypropylene/ethylene‐propylene‐diene copolymer (PP/EPDM) elastomers. The effect of silane crosslinking on the flame retardancy of the PP/EPDM composites containing melamine phosphate (MP) and dipentaerythritol (DPER) was studied by limiting oxygen index, UL 94 and cone calorimetry tests. The chemical composition of the silane crosslinked and flame retarded PP/EPDM composites treated at different temperatures was studied by X‐ray photoelectron spectroscopy and real time Fourier transform infrared (FTIR) spectrometry. Thermal decomposition and crystallization behavior of the PP/EPDM composites were investigated using thermogravimetric analysis and differential scanning calorimetry, respectively. Moreover, the mechanical properties of the composites were also studied. It is found that the flame retardancy, mechanical properties, and thermal decomposition behavior of the composites are influenced by silane grafting and crosslinking. Copyright © 2008 John Wiley & Sons, Ltd.     

In situ reactive compatibilization of polypropylene/epoxidized natural rubber blends by electron induced reactive processing: novel in‐line mixing technology

Blends of polypropylene (PP) and epoxidized natural rubber (ENR) were prepared by an in‐line electron induced reactive processing technique. The mixing was done in a Brabender mixing chamber coupled with an electron accelerator. The effect of sequence of electron treatment on the compatibilization of non‐polar PP and polar ENR was investigated in the presence of triallyl cyanurate (TAC). Finally, the resulting blends were characterized by different techniques, namely, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), tensile tests, and rheological studies. Generation of phase coupling and chemical compatibilization were observed from FTIR analysis. DMA studies showed enhanced high‐temperature modulus (above the glass transition temperature of both components) followed up by lowering in the tan δ peak. Rheological studies showed increase in modulus at low frequencies. Electron treatment and incorporation of rubber phase into PP showed significant effect on the degree of crystallinity of the blends, which was characterized by DSC study. The results obtained from FTIR, DMA, SEM, rheological studies, and tensile tests strongly affirmed that electron induced reactive processing of PP in presence of TAC before adding of ENR performed the best amongst all samples modified with electrons investigated in this study. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication and characterization of composites composed of a bioresorbable polyester matrix and surface modified calcium carbonate whisker for bone regeneration

This work aims to evaluate the potential of a bioresorbable composite as material for bone regeneration. Surface‐modified calcium carbonate whiskers (CCWs) were prepared by grafting of ethylene glycol (EG) using 1,6‐hexamethylene diisocyanate as coupling agent, followed by ring‐opening polymerization of l ‐lactide initiated by the hydroxyl group of EG. The resulting PLLA‐EG‐g‐CCW was used as filler to reinforce a bioresorbable terpolymer, poly(l ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG). The mechanical properties and thermal stability of the PLTG/PLLA‐EG‐g‐CCW composites were greatly improved. Compared with neat PLTG, a 39.3% increase in tensile strength and 26.7% increase in elongation at break were obtained for the composite with 2 wt% PLLA‐EG‐g‐CCW filler. This was assigned to the reinforcement effect of evenly dispersed PLLA‐EG‐g‐CCW in the polymeric matrix. In fact, entanglement of PLLA grafts at the surface of PLLA‐EG‐g‐CCW with PLTG chains results in a homogeneous distribution of the filler in the matrix. Thus, the composites are simultaneously strengthened and toughened. The cytocompatibility of the materials was evaluated from cell morphology and 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide assay using L929 mouse fibroblast cell line. The results indicate that the composite presents very low cytotoxicity. Copyright © 2017 John Wiley & Sons, Ltd.     

Plasma modification of polypropylene surfaces and grafting copolymerization of styrene onto polypropylene

The surface of polypropylene(iPP) is modified with glow discharge plasma of Ar,so that the modified surfaces of iPP films are obtained.The studies of scanning electron microscopy(SEM) show the surface etching pattern of iPP films. The chemical structures of iPP films are confirmed by X-ray photoelectron spectroscopy(XPS) and Fourier transform infrared(FTIR) spectroscopy.The wetting properties of modified surfaces of iPP films are characterized by contact angle, and the free energy of surfaces is calculated.The free radical of modification surfaces of iPP is measured by chemical method.The surfaces of iPP are achieved with Ar plasma treatment followed by grafting copolymerization with styrene(St) in St.The grafting polymer of St onto iPP is characterized by FTIR.The grafting rate is dependent on plasma exposure time and discharge voltage.The studies show that homopolymerization of St is undergone at the same time during the grafting-copolymerization of St onto iPP.     

Mechanical properties and morphological structures of short glass fiber reinforced PP/EPDM composite

The mechanical properties and crystal morphological structures of short glass fiber (SGF) reinforced dynamically photo-irradiated polypropylene (PP)/ethylene-propylene-diene terpolymer (EPDM) composites were studied by mechanical tests, wide-angle X-ray diffraction (WAXD), optical microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). The mechanical properties of PP/EPDM composites, especially the tensile strength were greatly strengthened by dynamically photo-irradiation and the incorporation of SGF. The results from the WAXD, SEM, DSC, and TGA measurements reveal: (i) the formation of β-type crystal of PP in the PP/EPDM/SGF composite; (ii) the fiber length in dynamically photo-irradiated PP/EPDM/SGF composites are general longer than that in corresponding unirradiated samples. The size of EPDM phase in the photo-irradiated composites reduces obviously whereas the droplet number increases; (iii) photo-irradiation improves the interface adhesion between SGF and polymer matrix; (iv) the melting and crystallization temperatures of the photo-irradiated composites are not affected greatly by increasing the SGF content; (v) the thermal analysis results show that the incorporation of SGF into PP/EPDM plays an important role for increasing its thermal stability.     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226     

The processing and properties of conductive polypropylene/polypyrrole composites

Polypropylene (PP) particles were chemically coated with polypyrrole (PPy). The content of polypyrrole varied from 0.8 to 7.6 wt.-%. Electrical conductivity of compression moulded samples depends on the concentration of polypyrrole and reached values from 4×10⁻¹⁰ to 5×10⁻³ S/cm, which is about 7 orders of magnitude higher than the conductivity in the blends prepared by mechanical mixing of PP and PPy in the same PPy concentration range. Highly conductive composites were also obtained from a mixture of coated and non-coated PP particles. The PP/PPy composites were characterized by elemental analysis, SEM and mechanical testing. The antistatic properties of PP/PPy composites were demonstrated. The electrical and mechanical properties depend on processing of composites.     

Composites of poly(L‐lactide‐trimethylene carbonate‐glycolide) and surface modified SBA‐15 as bone repair material

This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H₂N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N₂ adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity.     

A novel phase-change composites based on silicone rubber containing energy-storage microcapsules

A novel phase-change composites based on silicone rubber (MVQ) containing n-octadecane/poly (styrene-methyl methacrylate) microcapsules were successfully obtained by mixing energy-storage microcapsules into MVQ matrix using three preparation methods. The effect of microcapsules content on thermal property of the composites was investigated by thermogravimetric analysis. The mechanical properties of the composites prepared by three methods were also investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM), differential scanning calorimetry, and thermal response. Thermal and mechanical properties of the composites were excellent when the microcapsules were added into room temperature vulcanized silicone rubber with 2 phr (per hundred rubber) content and cured at room temperature. The composites were proved to have good energy-storage performance with 67.6 J g^?1 enthalpy value.     

Polypropylene wax (PPw)/silica hybrid by in situ non-aqueous sol–gel process for preparation of PP/silica nanocomposites

This paper presented a novel approach to prepare PP/silica nanocomposites. First, PPw-g-KH570 (γ-methacryloxypropyl trimethoxysilane) was obtained by pre-irradiation grafting method and characterized by FTIR and TGA. Then the non-aqueous sol–gel gelation kinetics of TEOS (tetraethoxysilane)-formic acid system in xylene was researched. Subsequently PPw/silica hybrid was obtained by in situ non-aqueous sol–gel reaction of TEOS in the presence of PPw-g-KH570 solution in xylene. Finally PP/silica nanocomposites were prepared by blending of PP matrix and PPw/silica hybrid. The mechanism of in situ formed PPw/silica hybrid was proposed. The morphology of PPw/silica hybrid and microstructures of PP/silica nanocomposites were characterized by TEM and SEM. The mechanical and thermal properties of PP/silica nanocomposites were also well studied by tensile tests and DSC. It was showed that the nanosilica particles were well dispersed in PPw/silica hybrid with the aid of grafting KH570 due to co-condensation by grafted KH570 and TEOS. PPw/silica hybrid was well dispersed in PP matrix with good compatibility and strong interactions. The resulted PP/silica nanocomposites possessed better performance than that of pure PP matrix.     

Preparation, structure and properties of PP-g-AA grafting copolymer

Polypropylene grafting with AA was prepared by reactive extrusion with pre-irradiated PP (rPP) as the homogeneous initiator. The effects of the pre-irradiated dose, the fraction of rPP and the concentration of acrylic acid on the grafting reaction were studied and the grafted PP was characterized by Fourier transition infrared spectroscopy (FTIR), differential scanning calorimeter (DSC) and polarized light microscopy (PLM). The results show that the degradation of PP was suppressed efficiently with this novel method for preparing PP-g-AA copolymers, and the grafted copolymers with good mechanical properties were obtained. It was found that the product with higher graft degree (G _d)(0.19%) and relatively excellent mechanical properties can be produced if the mass ratio of PP/rPP/AA is 90:10:0.8, where the selected pre-irradiation dose of rPP is 4 kGy. Moreover, an adhesive strength of 4.88 kN/m was reached in the PP-g-AA/aluminum laminate. __________ Translated from Chinese Journal of Applied Chemistry, 2007, 24(7): 737–741 [译自: 应用化学]     

Thermal and microstructural characterization of compatibilized polystyrene/natural fillers composites

Composites of polystyrene (PS) with cellulose microfibres and oat particles, obtained by melt mixing, were examined. The compatibilization of the composites was carried out by addition of maleic anhydride-functionalized copolymers (SEBS-g-MA, PS-co-MA) and poly(ethylene glycol) to improve the fibre–matrix interfacial interactions. The plain components and their composites were characterised by FT-IR, DSC, TGA, SEM microscopy and mechanical tests. The properties of the various systems were analysed as a function of both fibre and compatibilizer amount. The compatibilized PS composites showed enhanced fibre dispersion and interfacial adhesion as a consequence of chemical interactions between the anhydride groups on the polymer chains and the hydroxyl groups on the fibres, as demonstrated by FT-IR spectroscopy. DSC analysis pointed out a neat increase of T _g of composites on addition of SEBS-g-MA, as compared to PS-co-MA. The thermal stability of composites was also influenced by the type and amount of fibres, as well as by the structure and concentration of compatibilizer. The effect of the reactive copolymers on the composites properties was accounted for on the basis of the polymer–polymer miscibility and chemical interactions at the matrix/filler interface.     

Morphological investigation of PP/nanosilica composites containing SEBS

The effect of styrene-(ethylene-co-butylene)-styrene triblock copolymer (SEBS) on the mechanical, thermal and morphological properties of polypropylene (PP) composites filled with nanosilica particles is investigated. A simultaneous increase of all tensile characteristics is observed in PP/nanosilica composites without SEBS and containing 5%SEBS and a large plastic deformation in the nanocomposite with 10%SEBS. Different amounts of β-PP are detected by X-ray diffraction analysis and the calculated K-values correlate well with differential scanning calorimetry results. Quantitative mechanical characterization of nanocomposites is performed at nanolevel, using peak force QNM. This AFM technique allows the detection of nanosilica particles and SEBS domains at the surface of samples and gives indications of local interactions between nanosilica and the matrix from the correlation of modulus and adhesion maps, and the increased local values of elastic modulus on extended areas around nanoparticles.     

Improved thermal oxidation stability of polypropylene films in the presence of β-nucleating agent

Thermal oxidation behavior of isotactic polypropylene (PP) films with and without nucleating agent was investigated at 100 °C in air. The crystal form of PP was modified with a specific aryl amide derivative as β-nucleating agent (β-NA). Fourier transform infrared spectroscopy (FTIR), polarized optical microscopy (POM), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and tensile tests were performed to determine the extent of chemical degradation and the variations of microstructure of the two kinds of PP films during thermal oxidation. It was found that the mechanism of thermal oxidation of PP films was not changed in the presence of β-NA, but the time to initiation and the rate of oxidation both declined. Moreover, during the thermal oxidation aging, the melting temperature of neat PP significantly decreased while only a slight decrease of the melting temperature occurred for β-PP. Overall, the investigation indicated that the thermal oxidative stability of β-PP was higher than that of neat PP. The underlying mechanism was further analyzed by considering the change in the physical structure, especially the crystalline and the amorphous structure, of PP in the presence of β-NA.     

Electrospinning of carboxymethyl starch/poly(L‐lactide acid) composite nanofiber

Carboxymethyl starch (CMS) is a natural polymer derived from sago starch that is obtained from sago palm (Metroxylon spp.). Herein, CMS was used as a polysaccharide source in preparations of composite nanofibers with poly(L‐lactide acid) (PLLA). The incorporation of CMS with PLLA in nanofiber form has great potential to be used in biomedical applications. The composite PLLA/CMS nanofibers were fabricated by electrospinning technique at various ratios of CMS, which were 5, 10, 15, and 20% vol/vol. The composite nanofibers were characterized according to their physical morphology, chemical interaction, wettability, water uptake, and thermal and mechanical behaviors. The result showed that uniform and bead‐free nanofibers were produced at the low ratio of CMS while fractal and discontinuing fiber was observed at a high ratio of CMS. A better mechanical strength was obtained at low CMS ratio as compared with higher one. Fourier transform infrared results showed that there was an interaction between CMS and PLLA after electrospinning. The surface hydrophilicity and water uptake increased with increasing ratio of CMS. The results from the differential scanning calorimeter analysis showed the decrease of the glass transition (T_g) and cold crystallization temperature (T_cc) of the nanofiber after addition of CMS in PLLA.