Voltammetric study and electroanalytical determination of contraceptive levonorgestrel using silver solid amalgam electrode fabricated with nanoparticles

Here we describe the investigation of the electrochemical behaviour and the electroanalytical quantification of hormonal contraceptive levonorgestrel using solid amalgam electrode fabricated with silver nanoparticles. Until now, to the best of our knowledge, this is the first report of the use of solid working electrodes for levonorgestrel determination. Over this electrodic surface, the substance showed one cathodic peak at E_p = ?1.41 V. Moreover, the electrochemical reduction of levonorgestrel was defined as an irreversible and mainly adsorption-controlled process involving two protons and two electrons. Square-wave adsorptive stripping voltammetry (SWAdSV) was used for the quantification of levonorgestrel. The instrumental and experimental parameters were studied and optimized. The best conditions of analysis were observed when using 0.04 mol L^?1 Britton–Robinson (BR) buffer at pH 6.0. The analytical signal of levonorgestrel showed a linear dependence on the concentration range from 5.03 × 10^?7 mol L^–1 to 1.01 × 10^?5 mol L^–1. The LOD and LOQ obtained were 9.09 × 10^?8 mol L^?1 and 3.03 × 10^?7 mol L^?1, respectively. The voltammetric method was employed for the quantification of levonorgestrel in real pharmaceutical formulations and urine samples. The results provided good concordance with the expected values. It makes the working electrode used here an interesting and less toxic option for the analysis of reducible substances in comparison with the HMDE.     

Voltammetric determination of herbicide molinate in river water and rice samples using solid silver amalgam electrode fabricated with nanoparticles

The evaluation of the voltammetric behaviour and the determination of herbicide molinate were performed for the first time over the surface of solid amalgam electrode fabricated with silver nanoparticles using cyclic voltammetry and square-wave voltammetry techniques. The experimental and instrumental parameters were evaluated to reach the maximum analytical response for molinate. It was achieved when a medium composed of 0.04 mol L^?1 Britton–Robinson buffer at the pH value of 4.0 was used. Under these conditions, molinate showed one pronounced reduction peak at E_p = ?0.37 V (vs. Ag/AgCl 3 mol L^?1) that was characterised as an irreversible system. An analytical curve was constructed at the concentration range from 9.36 to 243.49 µg L^?1 and a limit of detection of 2.34 µg L^?1 was obtained. The amalgam electrode presented good stability during the measurements with relative standard deviation (RSD) values of 2.9% for the repeatability and 5.4% for the reproducibility. The voltammetric method developed here could be conveniently applied for the determination of molinate in river water and rice spiked samples at levels below those established on the legislations of European Union and Brazil with good accuracy (RSD of less than 5% for all samples). Comparison with HPLC technique was carried out and the results indicated satisfactory concordance. According to the results depicted here, the silver nanoparticles solid amalgam electrode showed itself highly sensitive and an interesting alternative for the routine analysis of molinate in water and food samples. Furthermore, it introduces an environmentally acceptable alternative to the mercury electrodes, most commonly used for determination of reducible pesticides.     

Voltammetric determination of phytochelatins using copper solid amalgam electrode

Voltammetric determination of synthetically prepared phytochelatins (γ-Glu-Cys)₂Gly (PC₂) and (γ-Glu-Cys)₃Gly (PC₃) has been studied using new type of copper solid amalgam electrode. The determination, based on the formation of cuprous complexes in buffer pH 8.1, is suitable for concentrations of PC in the range 10–100 nmol l⁻¹. Reproducibility, employing electrochemical cleaning of the electrode surface, was statistically evaluated. The achieved limit of detection (2.1–2.6×10⁻⁹ mol l⁻¹ for DCV measurement) together with the robust character of the electrode offer its use for detection of PCs in separated extracts of real samples.     

Application of renewable silver amalgam annular band electrode to voltammetric determination of vitamins C, B1 and B2

In this work, the design and results of applying silver liquid amalgam film-modified silver solid amalgam annular band electrode (AgLAF-AgSAE), refreshed before each measurement, to voltammetric determination of vitamins C (VC), B₁ (VB1) and B₂ (VB2) are presented. The method is based on adsorptive accumulation of analytes at the AgLAF-AgSAE in a phosphate buffer (VB1), phosphate buffer with Triton X-100 (VB2) and an alkaline borate buffer with Triton X-100 (VC). The analytical parameters and procedure of electrode activation were optimized. The calibration graphs obtained for vitamins C, B₁ and B₂ are linear, respectively, for concentration range 0.05-12, 0.01-0.1 and 0.05-3 mg L⁻¹. The detection limits were calculated and equaled 0.02, 0.003 and 0.009 mg L⁻¹, while repeatability of the peak current was 2%, 1% and 3%, respectively. These results are comparable with results obtained for polarographic determination of the same vitamins using mercury electrodes. Finally, the AgLAF-AgSAE was applied to the determination of vitamins in pharmaceutical samples and fruit juices with satisfactory results.     

没食子酸在电活化玻碳电极上的电化学行为及测定

采用循环伏安法和线性扫描伏安法对没食子酸在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在pH7.0的磷酸盐缓冲溶液中,用恒电位法在1.7 V电位阳极氧化400 s。然后在pH3.0的柠檬酸盐缓冲溶液中,没食子酸在0.479 V和0.442 V处有一良好的氧化还原峰,在0.02～0.40 V s-1范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的准可逆过程。线性循环伏安法的氧化峰电流与没食子酸浓度1×10-6～1×10-4mol L-1范围内呈良好的线性关系(r=0.980 6),检出限为7.6×10-7mol L-1(S/N=3)。该方法操作简便,重现性较好,并应用此法分析了健民咽喉片剂中的没食子酸的含量。     

Electrochemical properties and square-wave voltammetric determination of pravastatin

The electrochemical reduction and adsorptive voltammetric behaviour of pravastatin have been studied by means of cyclic and square-wave voltammetry at a hanging mercury-drop electrode in electrolytes of different pH. Within the entire pH range (2.0–9.0) in Britton–Robinson buffer, pravastatin gave rise to a single voltammetric peak in the potential interval from −1.22 to −1.44 V, depending on pravastatin concentration. It was found that the reduction of pravastatin proceeds via a relatively stable intermediate, which is transformed to the final electroinactive product by a coupled chemical reaction or can be re-oxidized back to pravastatin. The rate of chemical transformation is controlled by the proton concentration. The electrode mechanism has the properties of a surface redox reaction. A sensitive analytical method for trace analysis of pravastatin based on the adsorptive stripping technique has been developed. The calibration plot was linear in the range 8×10⁻⁸–5×10⁻⁷ mol L⁻¹. Application of the square-wave voltammetric method to determination of pravastatin in a pharmaceutical dosage form, without sample pretreatment, resulted in acceptable deviation from the stated concentration.     

Determination of lead and cadmium in seawater using a vibrating silver amalgam microwire electrode

Silver amalgamated electrodes are a good substrate to determine lead (Pb) and cadmium (Cd) in seawater because they have properties similar to mercury but without the free mercury (Hg). Here a silver amalgamated microwire (SAM) electrode is optimised for the determination of Pb and Cd in coastal waters and uncontaminated ocean waters. The SAM was vibrated during the deposition step to increase the sensitivity, and electroanalytical parameters were optimised. The Hg coating required plating from a relatively concentrated (millimolar) solution, much greater (500×) than used for instance to coat glassy carbon electrodes. However, the coating on the ex situ amalgamated electrode was found to be stable and could be used for up to a week to determine trace levels of Pb in seawater of natural pH. The limit of detection square-wave ASV (50 Hz) using the pre-plated SAM electrode was 8 pM Pb using a 1-min plating time at pH 4.5. The limit of detection in pH 2 seawater was 4 pM using a 5-min plating time, and it was 12 pM using a 10-min plating time at natural pH in the presence of air, using a square-wave frequency of 700 Hz. The vibrating SAM electrode was tested on the determination of Pb in reference seawater samples from the open Atlantic (at the 20 pM level), Pacific, and used for a study of Pb in samples collected over 24 h in Liverpool Bay (Irish Sea).     

Voltammetric determination of dinitronaphthalenes using a silver solid amalgam paste electrode

The electrochemical behavior and application of a new sensor, a silver solid amalgam paste electrode (AgSA-PE), based on the mixture of a fine silver solid amalgam powder (60:40 (w(Hg)/w(Ag))) and a suitable organic pasting liquid (Paraffin oil) in a ratio of 20:1 (w/w), was investigated in an aqueous-methanolic media (1:1). This alternative working electrode provides simple preparation and handling, adequate mechanical stability, easily renewable electrode surface, sufficiently wide cathodic potential window (up to -1200 mV within a pH range of 2.7-12.3), and sufficient sensitivity without any necessary pretreatment. The practical usability of the AgSA-PE was verified by the development of voltammetric methods for the determination of selected environmentally important pollutants (1,3-, 1,5-, and 1,8-dinitronaphthalenes) in an aqueous-methanolic media (1:1). The differential pulse voltammetric methods at AgSA-PE give linear concentration dependences in the range of 1-100 μmol l(-1) with limits of detection of about 1 μmol l(-1) in a mixture of Britton-Robinson buffer of appropriate pH and methanol (1:1).     

钡离子在玫红酸钠修饰碳糊电极上电化学固相微萃取研究

本文以电化学活性的玫红酸钠修饰碳糊电极,利用玫红酸盐与钡离子的络合效应,实现钡离子的电化学固相微萃取。以循环伏安法研究了钡离子的固相微萃取及其最佳实验条件。固相微萃取的动力学符合S形曲线模型,获得表观一级反应速率常数为2.183 min-1。固相微萃取的热力学遵循Freundlich等温吸附模型,吸附常数为n=11.4,k=1.025。     

Differential pulse voltammetric determination of selected nitrophenols on novel type of porous silver working electrode prepared by powder metallurgy

Nitrophenols are important environmental pollutants and their monitoring is important because of their genotoxic and ecotoxic properties. Easy electrochemical reduction of nitro groups can be used for their voltammetric determination using mercury based electrodes. However, requirements of green analytical chemistry prompted us to investigate a novel type of silver porous electrode (AgPE) prepared by powder metallurgy compatible with both “green” and “white” analytical chemistry requirements. In this paper, AgPE was for the first time successfully used for differential pulse voltammetric determination of micromolar concentrations of 2-nitrophenol (NP), 2,4-dinitrophenol (DNP), and 2,4,6-trinitrophenol (TNP) in aqueous media. The main advantage of the novel method is the possibility to use small sample volume (down to 25 μL) and to work in the presence of oxygen when using supporting electrolyte of pH 3. This advantage partially compensates the fact that the obtained sensitivity and limit of detection are not better than with the previously investigated electrodes.     

甘草苷在悬汞电极上的电化学行为及方法研究

运用循环伏安法(CV)考察了甘草苷在悬汞电极(HMDE)上的电化学还原行为,在-0.7~-1.7 V(vs.SCE)电位窗口及0.10 mol/L(NH4)2SO4溶液中甘草苷在HMDE上的循环伏安行为是一在低扫描速度(<100 mV/s)下受吸附控制,在高扫描速度下受扩散控制的不可逆还原过程,还原峰电位(Epc)为-1.491 V。运用计时库仑法(CC)、计时电流法(CA)测定并计算了甘草苷的电荷传递系数α、扩散系数D以及表观速率常数Kf等电极过程动力学参数。初步探讨了甘草苷在HMDE上的反应机理,同时运用方波伏安法(SWV)研究了甘草苷在HMDE上的方波伏安行为,还原峰电流与其浓度在1.2×10-6~1.2×10-5mol/L及1.2×10-5~1.2×10-3mol/L范围内呈良好的线性关系,相关系数R=0.9936及0.9966,检出限8.0×10-7mol/L,据此可建立直接电化学测定甘草苷含量的方法。     

依诺沙星在碳糊电极上的阳极吸附伏安法研究

在0.40 mol/L的NaAc-HAc(pH 4.5)缓冲液中,使用JP-303极谱分析仪,依诺沙星在碳糊电极(CPE)上有一灵敏的吸附伏安氧化峰,峰电位为1.17 V(vs.SCE).该氧化峰的二阶导数峰电流与依诺沙星的浓度在4.0×10-9～4.0×10-7 mol/L(富集90 s)范围内呈良好的线性关系,相关系数为0.995,检出限为2.0×10-9 mol/L(S/N=3,富集110 s).探讨了依诺沙星在碳糊电极上的伏安性质和电极反应机理,并且用于诺佳胶囊中依诺沙星的测定.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.     

Bismuth film electrode for anodic stripping voltammetric determination of tin

The bismuth film electrode (BiFE), in combination with anodic stripping voltammetry, offers convenient measurement of low concentrations of tin. The procedure involves simultaneous in situ formation of the bismuth film electrode on a glassy carbon substrate electrode, together with electrochemical deposition of tin, in a non-deaerated model solution containing bismuth ions, catechol as complexing agent and the metal analyte, followed by an anodic stripping scan. The BiFE is characterized by an attractive electroanalytical performance, with two distinct voltammetric stripping signals corresponding to tin, accompanied with low background contributions. Several experimental parameters were optimized, such as concentration of bismuth ions and catechol, deposition potential, deposition time and pH of the model solution. In addition, a critical comparison is given with bare glassy carbon and mercury film electrodes, revealing the superior characteristics of BiFE for measurement of tin. BiFE exhibited highly linear behavior in the examined concentration range from 1 to 100 μg L⁻¹ of tin (R² = 0.997), an LoD of 0.26 μg L⁻¹ tin, and good reproducibility with a calculated R.S.D. of 7.3% for 10 μg L⁻¹ tin (n = 10). As an example, the practical applicability of BiFE was tested with the measurement of tin in a real sample of seawater.     

Sensitive voltammetric determination of gallium in aluminium materials using renewable mercury film silver based electrode

Simple cyclic renewable silver amalgam film electrode (Hg(Ag)FE), applied for the determination of gallium(III) using differential pulse anodic stripping voltammetry (DP ASV), is presented. The effects of various factors such as: preconcentration potential and time, pulse height, step potential and supporting electrolyte composition are optimised. The calibration graph is linear from 5?nM (0.35?µg?L^?1) to 80?nM (5.6?µg?L^?1) for a preconcentration time of 60?s, with correlation coefficient of 0.995. For a Hg(Ag)FE with a surface area of 9.9?mm² the detection limit for a preconcentration time of 120?s is as low as 0.1?µg?L^?1. The repeatability of the method at a concentration level of the analyte as low as 3.5?µg?L^?1, expressed as RSD is 3.2% (n?=?5). The proposed method was successfully applied by studying the synthetic samples and simultaneously recovery of Ga(III) from spiked aluminium samples.     

Determination of 5-nitroindazole using silver solid amalgam electrode

Monatshefte für Chemie - Chemical Monthly - The voltammetric behavior of 5-nitroindazole was investigated at polished (p-AgSAE) and at mercury meniscus-modified (m-AgSAE) silver solid amalgam...     

Simultaneous voltammetric determination of paracetamol and caffeine in pharmaceutical formulations using a boron-doped diamond electrode

A simple and highly selective electrochemical method was developed for the single or simultaneous determination of paracetamol (N-acetyl-p-aminophenol, acetaminophen) and caffeine (3,7-dihydro-1,3,7-trimethyl-1H-purine-2,6-dione) in aqueous media (acetate buffer, pH 4.5) on a boron-doped diamond (BDD) electrode using square wave voltammetry (SWV) or differential pulse voltammetry (DPV). Using DPV with the cathodically pre-treated BDD electrode, a separation of about 550 mV between the peak oxidation potentials of paracetamol and caffeine present in binary mixtures was obtained. The calibration curves for the simultaneous determination of paracetamol and caffeine showed an excellent linear response, ranging from 5.0 × 10⁻⁷ mol L⁻¹ to 8.3 × 10⁻⁵ mol L⁻¹ for both compounds. The detection limits for the simultaneous determination of paracetamol and caffeine were 4.9 × 10⁻⁷ mol L⁻¹ and 3.5 × 10⁻⁸ mol L⁻¹, respectively. The proposed method was successfully applied in the simultaneous determination of paracetamol and caffeine in several pharmaceutical formulations (tablets), with results similar to those obtained using a high-performance liquid chromatography method (at 95% confidence level).