Multiplex sensor for detection of different metal ions based on on–off of fluorescent gold nanoclusters

In this study, a multiplex fluorescence sensor for successive detection of Fe³⁺, Cu²⁺ and Hg²⁺ ions based on “on–off” of fluorescence of a single type of gold nanoclusters (Au NCs) is described. Any of the Fe³⁺, Cu²⁺ and Hg²⁺ ions can cause quenching fluorescence of Au NCs, which established a sensitive sensor for detection of these ions respectively. With the introduction of ethylene diamine tetraacetic acid (EDTA) to the system of Au NCs and metal ions, a restoration of fluorescence may be found with the exception of Hg²⁺. A highly selective detection of Hg²⁺ ion is, thus, achieved by masking Fe³⁺ and Cu²⁺. On the other hand, the masking of Fe³⁺ and Cu²⁺ leads to the enhancement of fluorescence of Au NCs, which in turn provides an approach for successive determination of Fe³⁺ and Cu²⁺ based on “on–off” of fluorescence of Au NCs. Moreover, this assay was applied to the successful detection of Fe³⁺, Cu²⁺ and Hg²⁺ in fish, a good linear relationship was found between these metal ions and the degree of quenched fluorescent intensity. The dynamic ranges of Hg²⁺, Fe³⁺ and Cu²⁺ were 1.96 × 10⁻¹⁰–1.01 × 10⁻⁹, 1.28 × 10⁻⁷–1.27 × 10⁻⁶ and 1.2 × 10⁻⁷–1.2 × 10⁻⁶ M with high sensitivity (the limit of detection of Fe³⁺ 2.0 × 10⁻⁸ M, Cu²⁺ 1.9 × 10⁻⁸ M and Hg²⁺ 2 × 10⁻¹⁰ M). These results indicate that the assay is suitable for sensitive detection of these metal ions even under the coexistence, which can not only determine all three kinds of metal ions successively but also of detecting any or several kinds of metal ions.     

A novel colorimetric and fluorescent chemosensor: synthesis and selective detection for Cu and Hg

A novel two-channel metal ion sensor has been synthesized from macrocyclic dioxotetraamine and 1,8-naphthalimide derivative. The metal ion-selective signaling behaviors of the sensor were investigated. The sensor presented the selective coloration for Cu²⁺ and Hg²⁺ that can be detected by the naked-eye, respectively. Besides, the addition of Cu²⁺ and Hg²⁺ quenched the fluorescence of 1 obviously and the detection limit was found to be 3 × 10⁻⁷ M for Cu²⁺ and 7 × 10⁻⁷ M for Hg²⁺. This sensor can be utilized for the visual and spectroscopic detection of Cu²⁺ or Hg²⁺ in the presence of the other competing metal ions.     

Probing trace Pb(2+) using electrodeposited N,N'-(o-phenylene)-bis-benzenesulfonamide polymer as a novel selective ion capturing film

A novel film modified electrode for the determination of trace lead was developed in this work. The modified electrode was prepared by the electropolymerization of N,N′-(o-phenylene)-bis-benzenesulfonamide (PBSA) as the ion capturing reagent to create the functional film. The modified electrode shows a high selectivity towards Pb²⁺ over interfering cations, e.g. Cu²⁺, Cd²⁺, Co²⁺, Ni²⁺, Zn²⁺, Cr²⁺, and the calibration curve was linear in the concentration range of 2.0 × 10⁻⁹ to 1.0 × 10⁻⁷ M with correlation coefficient of 0.999. For 20 min accumulation, detection limit of 1.0 × 10⁻⁹ M was obtained at the signal to noise ratio of 3. Analytical availability of the modified electrode was demonstrated by the application for samples from pond water.     

Fluorogenic dual click derived bis-glycoconjugated triazolocoumarins for selective recognition of Cu(II) ion

Carbohydrate based fluorescent sensors S1 and S2 have been developed by fluorogenic dual click chemistry and are characterized by various spectroscopic techniques. Both the fluorescent probes displayed highly selective detection of Cu²⁺ ions by means of fluorescence quenching. The job plot experiment suggested 1:1 complexation of probes S1 and S2 with Cu²⁺ ions having detection limit of 6.99 μM and 7.30 μM, respectively. The binding constants for S1-Cu²⁺ and S2-Cu²⁺ complexation were evaluated to be 3.34 × 10³ M⁻¹ and 5.93 × 10³ M⁻¹, respectively.     

Fluorescence enhancement of CdTe/CdS quantum dots by coupling of glyphosate and its application for sensitive detection of copper ion

A novel fluorescent probe for Cu²⁺ determination based on the fluorescence quenching of glyphosate (Glyp)-functionalized quantum dots (QDs) was firstly reported. Glyp had been used to modify the surface of QDs to form Glyp-functionalized QDs following the capping of thioglycolic acid on the core–shell CdTe/CdS QDs. Under the optimal conditions, the response was linearly proportional to the concentration of Cu²⁺ between 2.4 × 10⁻² μg mL⁻¹ and 28 μg mL⁻¹, with a detection limit of 1.3 × 10⁻³ μg mL⁻¹ (3δ). The Glyp-functionalized QDs fluorescent probe offers good sensitivity and selectivity for detecting Cu²⁺. The fluorescent probe was successfully used for the determination of Cu²⁺ in environmental samples. The mechanism of reaction was also discussed.     

Copper(II)-selective electrode based on dithioacetal

A PVC membrane electrode for copper ion based on 1,3-dithiane,2-(4-methoxy phenyl) as ionophore and o-nitrophenyl octyl ether as a plasticizer is demonstrated. The electrode exhibits a Nernstian slope of 29.5±1 mV per decade in a linear range of 3.0×10⁻⁶ to 5.0×10⁻² M for Cu²⁺ ion. The detection limit of this electrode is 1.0×10⁻⁶ mol/l. This sensor has a very short response time of about 5 s and could be used in a pH range of 4.0-7.0. High selectivity was obtained over a wide variety of metal ions. The proposed electrode was successfully applied as an indicator electrode for the potentiometric titration of copper ion with EDTA and for the direct determination of copper in river water.     

Synthesis of Cu-mediated nano-sized salbutamol-imprinted polymer and its use for indirect recognition of ultra-trace levels of salbutamol

Cu²⁺-mediated salbutamol-imprinted polymer nanoparticles, synthesized by precipitation polymerization, were mixed with graphite powder and n-eicosane in order to fabricate a modified carbon paste electrode. This electrode was then applied for indirect differential pulse voltammetry determination of salbutamol. In the presence of Cu²⁺ ions, the formed Cu²⁺–salbutamol complex was adsorbed in to the pre-designed cavities of the MIP particles, situated on the electrode surface. Since the electrochemical signal of salbutamol was intrinsically small, the oxidation peak of the participant Cu²⁺, after reduction step, was recorded and used as an indication of salbutamol amount, adsorbed in the electrode. Different variables influencing the sensor performance were studied and the best conditions were chosen for the determination purpose. Correlation between the sensor response to salbutamol and its concentration was linear in the range of 1.0 × 10⁻⁹–5.5 × 10⁻⁸ M. Detection limit was calculated equal to 6.0 × 10⁻¹⁰ M (S/N). Five replicated determination of salbutamol (1 × 10⁻⁸ M) resulted in standard error of 3.28%, meaning a satisfactory precision of the determination method. The prepared sensor was applied for real sample analysis. In order to minimize the interference effect, the synthesized polymer was successfully used as a solid phase sorbent for salbutamol extraction, before analysis of real samples by the developed sensor.     

Comparative studies of mercapto thiadiazoles self-assembled on gold nanoparticle as ionophores for Cu(II) carbon paste sensors

Comparative studies of the potentiometric behavior of three mercapto compounds [2-((5-mercapto-1,3,4-thiadiazol-2-ylimino)methyl)phenol] (MTMP), [5-(2-methoxy benzylidene amino)-1,3,4-thiadiazole-2-thiol] (MBYT) and [5-(pyridin-2-ylmethyleneamino)-1,3,4-thiadiazole-2-thiol] (PYTT) self-assembled on gold nanoparticles (GNPs) as ionophores in carbon paste electrodes (CPEs) have been made. These mercapto thiadiazole compounds were self-assembled onto gold nanoparticles and then incorporated within carbon paste electrode. The self-assembled ionophores exhibit a high selectivity for copper ion (Cu²⁺), in which the sulfur and nitrogen atoms in their structure play a role as the effective coordination donor site for the copper ion. These carbon paste electrodes were applied as indicator electrodes for potentiometric determination of copper ions. The sensor based on PYTT exhibits the working concentration range of 4.0 × 10⁻⁹ to 7.0 × 10⁻² M and a Nernstian slope of 28.7 ± 0.3 mV decade⁻¹ of copper activity. The detection limit of electrode was 1.0 × 10⁻⁹ M and potential response was pH independent across the range of 3.0-6.5. It exhibited a quick response time of <5 s and could be used for a period of 45 days. The ion selectivity of this electrode for Cu²⁺ was over 10⁴ times that for other metal cations. The application of prepared sensors has been demonstrated for the determination of copper ions in spiked water and natural water samples.     

A new rhodamine-based dual chemosensor for Al and Cu

A new rhodamine B derivative bearing a hydrazone group has been designed and prepared. The synthesized colorimetric and fluorescent molecular chemosensor can be used as a dual probe, selectively detecting Al³⁺ and Cu²⁺ in acetonitrile solution by monitoring changes in the absorption and fluorescence spectral patterns. The results show that Al³⁺ ions can induce a greater fluorescence enhancement, while the addition of Cu²⁺ ions induces a strong UV–vis absorption enhancement with weak fluorescence. The limits of detection of Cu²⁺ and Al³⁺ were estimated to be 2.9 × 10⁻⁷ M and 8.3 × 10⁻⁹ M, respectively.     

Preparation for nitrocellulose membrane-poly (vinyl alcohol)-ionic imprinting and its application to determine trace copper by room temperature phosphorimetry

Nitrocellulose membrane-poly (vinyl alcohol)-ionic imprinting (NCM-PVA-I-I) was prepared using Cu²⁺ as template. The cavity in NCM-PVA-I-I matched Cu²⁺ very well and the selectivity was high. Cu²⁺ entered the cavity and then could form ionic association ([Cu²⁺]·[(Fin⁻)₂]) with the anion of fluorescein (Fin⁻) outside the cavity by electrostatic effect. [Cu²⁺]·[(Fin⁻)₂] could emit strong and stable room temperature phosphorescence on NCM-PVA-I-I. Its ΔI_p was proportional to the content of Cu²⁺. Based on the above facts, a new method for the determination of trace copper by solid substrate-room temperature phosphorimetry (NCM-PVA-I-I-SS-RTP, SS-RTP is the abbreviation of solid substrate-room temperature phosphorimetry) using NCM-PVA-I-I technique has been established. The linear range of this method was 2.00-144.00 fg Cu²⁺ spot⁻¹ (sample volume: 0.40 μL spot⁻¹, corresponding concentration: 5.00-360.00 pg mL⁻¹), and the detection limit calculated by 3Sb/k was 0.43 fg Cu²⁺ spot⁻¹ (corresponding concentration: 1.1 × 10⁻¹² g mL⁻¹, n = 11). Samples containing 2.00 and 144.00 fg Cu²⁺spot⁻¹ were measured, respectively, for seven times and R.S.D.s were 3.5% and 4.7%. NCM-PVA-I-I-SS-RTP could combine very well the characteristics of both the high sensitivity of SS-RTP and the high match and selectivity of NCM-PVA-I-I, and it was rapid, accurate, sensitive and with good repeatability. It has been successfully applied to determine trace copper in human hair and tea samples.     

Construction of a new Cu2+ coated wire ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylidene amino)phenyl)disufanyl)phenylimino)methyl)-4-methoxyphenol Schiff base

In this article a new coated platinum Cu²⁺ ion selective electrode based on 2-((2-(2-(2-(2-hydroxy-5-methoxybenzylideneamino)phenyl)disufanyl)phenylimino) methyl)-4-methoxyphenol Schiff base (L₁) as a new ionophore is described. This sensor has a wide linear range of concentration (1.2 × 10⁻⁷-1.0 × 10⁻¹ mol L⁻¹) and a low detection limit of 9.8 × 10⁻⁸ mol L⁻¹of Cu(NO₃)₂. It has a Nernstian response with slope of 29.54 ± 1.62 mV decade⁻¹ and it is applicable in the pH range of 4.0-6.0 without any divergence in potentioal. The coated electrode has a short response time of approximately 9 s and is stable at least for 3.5 months. The electrode shows a good selectivity for Cu²⁺ ion toward a wide variety of metal ions. The proposed sensor was successfully applied for the determination of Cu²⁺ ion in different real and environmental samples and as indicator electrode for potentiometric titration of Cu²⁺ ion with EDTA.     

Pre-evaluation of metal ions as a catalyst on chemiluminometric sequential injection analysis with luminol-H2O2 system

Catalytic effect of metal ions on luminol chemiluminescence (CL) was investigated by sequential injection analysis (SIA). The SIA system was set up with two solenoid micropumps, an eight-port selection valve, and a photosensor module with a fountain-type chemiluminescence cell. The SIA system was controlled and the CL signals were collected by a LabVIEW program. Aqueous solutions of luminol, H₂O₂, and a sample solution containing metal ion were sequentially aspirated to the holding coil, and the zones were immediately propelled to the detection cell. After optimizing the parameters using 1 × 10⁻⁵ M Fe³⁺ solution, catalytic effect of some metal species was compared. Among 16 metal species examined, relatively strong CL responses were obtained with Fe³⁺, Fe²⁺, VO²⁺, VO₃⁻, MnO₄⁻, Co²⁺, and Cu²⁺. The limits of detection by the present SIA system were comparable to FIA systems. Permanganate ion showed the highest CL sensitivity among the metal species examined; the calibration graph for MnO₄⁻ was linear at the concentration level of 10⁻⁸ M and the limit of detection for MnO₄⁻ was 4.0 × 10⁻¹⁰ M (S/N = 3).     

Naked-eye colorimetric analysis of Hg2+ with bi-color CdTe quantum dots multilayer films

A novel direct quantificational method through naked-eye colorimetric analysis of Hg²⁺ was constructed based on different degree of the fluorescence quenching of bi-color quantum dots (QDs) multilayer films (2-QDMF). The functional multilayer films were assembled by layer-by-layer (LBL) deposition of oppositely charged CdTe QDs and poly(dimethyldiallylemmonium chloride) (PDDA). Then the outermost layer of 2-QDMF was cross-linked to bovine serum albumin (BSA), polyethylene glycol (PEG) or glutathione (GSH). It was found that when BSA modified quartz slides were immersed into solutions containing Hg²⁺ and Cu²⁺ respectively, the 2-QDMF can be quenched by Hg²⁺, but not by Cu²⁺. Under the optimization conditions, the quenched photoluminescence (PL) intensities of multilayer films were almost linearly proportional to the concentration of Hg²⁺ in the range of 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol L⁻¹ and the detection limit was 4.5 × 10⁻⁹ mol L⁻¹. The proposed method is intuitional and convenient, which can be applied to the determination of trace Hg²⁺ in the artificial water sample with satisfactory results.     

Highly sensitive and reproducible cyclodextrin-modified gold electrodes for probing trace lead in blood

A highly sensitive and reproducible lead sensor based on a cyclodextrin-modified gold electrode was created. A self-assembled monolayer (SAM) of thiolated β-cyclodextrin (6-(2-mercapto-ethylamino)-6-deoxy-β-cyclodextrin (MEA-β-CD)) was prepared and modified on a gold electrode (MCGE) for specific Pb²⁺-sensing. Thus the mercury-free sensors for Pb²⁺ assay based on MCGE were established. A linear calibration response for Pb²⁺ was found in the range of 1.7 × 10⁻⁸ M to 9.3 × 10⁻⁷ M. The detection limit was 7.1 × 10⁻⁹ M (with S/N > 3), which was 10 times lower than other reported methods of detection Pb²⁺ with CD. The measurement results via this method for real blood samples were well agree with those obtained by ICP-AES, and thus presented a novel strategy in design of specific lead sensors with high sensitivity and stability for analysis of trace Pb²⁺ in real blood samples.     

A highly selective fluorescent sensor for Cu based on 2-(2′-hydroxyphenyl)benzoxazole in a poly(vinyl chloride) matrix

This paper describes a copper selective optical chemical sensor based on static quenching of the fluorescence of 2-(2′-hydroxyphenyl)benzoxazole entrapped in a poly(vinyl chloride) (PVC) membrane. The effect of the composition of the sensing membrane was studied, and experimental conditions were optimized. The sensors exhibit stable response over the concentration range from 4.0 × 10⁻⁸ M to 5.0 × 10⁻⁵ M Cu²⁺ at pH 4.0-6.5, and a high selectivity. The response time for Cu²⁺ with concentration ≤5 × 10⁻⁶ M is less than 7 min. The optode can be regenerated using 0.1 M HCl and acetate buffer solution. The sensor has been used for direct measurement of copper content in river water samples with a relative error less than 4% with reference to that obtained by atomic absorption spectrometry.     

Poly(vinyl chloride)-membrane ion-selective bulk optode based on 1,10-dibenzyl-1,10-diaza-18-crown-6 and 1-(2-pyridylazo)-2-naphthol for Cu and Pb ions

An ion-selective bulk optode (ISBO) for sensing Cu²⁺ and Pb²⁺ ions based on plasticized poly(vinyl chloride) containing 1,10-dibenzyl-1,10-diaza-18-crown-6 (DBzDA18C6) as ionophore and 1-(2-pyridylazo)-2-naphthol (PAN) as chromoionophore was prepared. The effects of DBzDA18C6/PAN and NaTPB/PAN mole ratios on the response behavior of the ISBO were investigated. The ISBO membrane shows enhanced selectivities for Cu²⁺ (at 530 nm) and Pb²⁺ (at 467 nm) over alkali, alkaline earth and other transition metal ions. The optical selectivity coefficients were measured using the separate solution method (SSM) in the two corresponding wavelengths at pH=5. The detection limit for Cu²⁺ and Pb²⁺ are 3.2×10⁻⁷ and 1.0×10⁻⁸ M, respectively.     

Complexation of metal ions with the novel azathia crown ethers carrying anthracene pendant in acetonitrile–dichloromethane

A series of crown ethers carrying an anthracene group with nitrogen–sulfur donor atom, which differ in having three, four and five sulfur atoms in the macrocycle was designed and synthesized by the reaction of the corresponding macrocyclic compound and 9-chloromethyl-anthracene. The influence of metal cations such as Al³⁺, Zn²⁺, Fe²⁺, Fe³⁺, Co²⁺, Ni²⁺, Mn²⁺, Cu²⁺, Cd²⁺, Hg²⁺ and Pb²⁺ on the spectroscopic properties of the ligands was investigated in acetonitrile–dichloromethane (1:1) by means of absorption and emission spectrometry. Absorption spectra show isosbestic points in the spectrophotometric titration of Al³⁺, Zn²⁺, Fe²⁺, Fe³⁺, Cu²⁺, Hg²⁺ and Pb²⁺ the results of which disclosed the complexation compositions and complex stability constants of the novel ligands with these cations. The monoazapentathia crown ether showed sensitivity for Al³⁺ with linear range and detection limit of 2.6 × 10⁻⁶ M–2.6 × 10⁻⁵ M and 8.1 × 10⁻⁷ M, respectively.     

A cationic porphyrin-based self-assembled film for mercury ion detection

A cationic 5,15-(p-(9,9-bis(6-trimethylammoniumhexyl)fluorenylethynyl)phenyl)porphyrin tetrabromide was synthesized and the self-assembled films were used for Hg²⁺ detection in aqueous media. The detection response is based on fluorescence quenching of the porphyrin molecule upon coordination with Hg²⁺. The detection shows high selectivity for Hg²⁺ over Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Mn²⁺, Ni²⁺, Co²⁺ and Ca²⁺. A linear response toward Hg²⁺ in a concentration range of 1 × 10⁻¹⁰-1 × 10⁻⁶ M was observed for the film with a detection limit of 0.1 nM. The cationic porphyrin film shows higher stability and significant improvement in detection sensitivity, as compared to other porphyrin-based sensors. The amphiphilic cationic nature of the porphyrin synthesized also allows for the direct deposition of a porphyrin layer on a bare glass surface through self-assembly.     

In-channel indirect amperometric detection of heavy metal ions for electrophoresis on a poly(dimethylsiloxane) microchip

In-channel indirect amperometric detection mode for microchip capillary electrophoresis with positive separation electric field is successfully applied to some heavy metal ions. The influences of separation voltage, detection potential, the concentration and pH value of running buffer on the response of the detector have been investigated. An optimized condition of 1200 V separation voltage, −0.1 V detection potential, 20 mM (pH 4.46) running buffer of 2-(N-morpholino)ethanesulfonic acid (MES) + l-histidine (l-His) was selected. The results clearly showed that Pb²⁺, Cd²⁺, and Cu²⁺ were efficiently separated within 80 s in a 3.7 cm long native separation PDMS/PDMS channel and successfully detected at a single carbon fibre electrode. The theoretical plate numbers of Pb²⁺, Cd²⁺, and Cu²⁺ were 1.2 × 10⁵, 2.5 × 10⁵, and 1.9 × 10⁵ m⁻¹, respectively. The detection limits for Pb²⁺, Cd²⁺, and Cu²⁺ were 1.3, 3.3 and 7.4 μM (S/N = 3).     

Novel potentiometric copper (II) selective membrane sensors based on cyclic tetrapeptide derivatives as neutral ionophores

Two novel membrane sensors sensitive and reasonably selective for Cu²⁺ ions are described. These are based on the use of newly synthesized cyclic tetrapeptide derivatives as neutral ionophores and sodium tetraphenylborate (NaTPB) as an anionic excluder in plasticized PVC membranes. The sensors exhibit fast and stable near-Nernstian response over the concentration range 1.0 × 10⁻⁶ mol l⁻¹ to 1.0 × 10⁻² mol l⁻¹ Cu²⁺ with a cationic slope of 30.2-25.9 mV per decade at pH 4.5-7 with a lower detection limit of 0.05-0.13 μg ml⁻¹. Effects of plasticizers, lipophilic salts and various foreign common ions are tested. The sensors display long life-span, long term stability, high reproducibility, and short response time. Selectivity of both sensors is significantly high for Cu²⁺ over Fe³⁺, Al³⁺, Zn²⁺, Cd²⁺, Hg²⁺, Ni²⁺, Co²⁺, Mn²⁺, alkaline earth and alkali metal ions. The sensors are used for direct measurement of copper content in different rocks and industrial wastewater samples from electroplating factories. The results agree fairly well with data obtained using atomic absorption spectrometry.