An alcohol oxidase biosensor using PNR redox mediator at carbon film electrodes

A new amperometric biosensor for ethanol monitoring has been developed and optimised. The biosensor uses poly(neutral red) (PNR), as redox mediator, which is electropolymerised on carbon film electrodes and alcohol oxidase (AlcOx) from Hansenula polymorpha as recognition element, immobilised by cross-linking with glutaraldehyde (GA) in the presence of bovine serum albumin (BSA) as carrier protein. Optimisation of variables affecting the system was performed and, for chronoamperometric measurements, a potential of −0.300 V versus saturated calomel electrode was chosen in 0.1 M sodium phosphate buffer saline at pH 7.5. The optimised biosensor showed a good sensitivity of 171.8 ± 14.8 nA mM⁻¹ and the corresponding detection limit (signal-to-noise-ratio = 3) of 29.7 ± 1.5 μM. Stability studies showed a good preservation of the bioanalytical properties of the sensor, 57.6% of its initial sensitivity remaining after 3 weeks (the sensor was used two to three times per week). No significant interferences were found from compounds usually present in wine. The biosensor was used for the determination of ethanol in Portuguese red and white wines.     

Quantification of the adsorption of methyl viologen on pyrex glass using a renewable perfluorosulfonated ionomer carbon paste electrode

Square wave voltammograms of methyl viologen (MV²⁺) were recorded at a renewable Nafion-loaded carbon paste electrode immersed in 20 mL of phosphate buffer solution (pH 7.4) contained in a beaker-type electrochemical cell (Pyrex glass; contact area = 33 cm²). From the calibration plot obtained in the concentration range 0.01–2.4 μM, it could be concluded that the maximum surface excess of MV²⁺ adsorbed on Pyrex glass (0.24 nmol cm⁻²) was reached at concentrations above 1.4 μM. The adsorption isotherm presented a sigmoidal shape characteristic of attractive interaction. From this plot, it was evaluated that the maximum depletion of MV²⁺ in solution (28%) did not occur at the lowest concentrations, but in nearly micromolar solutions. This result emphasizes the unavoidable and random errors which are involved when MV²⁺ solutions are purposely diluted in Pyrex glassware. The MV²⁺ adsorption proceeds to a less extent on Duran borosilicate glass and/or in acid or alkaline medium.     

Cholesterol oxidase biosensor based on a glassy carbon electrode modified with Nafion and methyl viologen

Cholesterol oxidase biosensor has been constructed by using bovine serum albumin and glutaraldehyde as cross linker to immobilize cholesterol oxidase and cholesterol esterase on a glassy carbon electrode modified with Nafion and methyl viologen. The biosensor has been used to determine total cholesterol in blood. The linear range of the determination is 2.5×10~7 to 1.0×10-4 mol/L. The detection limit is about 5.0×10~8 mol/L. The response time is 12 s. This biosensor has the advantage of high selectivity, sensitivity and short response time.     

Conductometric nitrate biosensor based on methyl viologen/Nafion/nitrate reductase interdigitated electrodes

A highly sensitive, fast and stable conductometric enzyme biosensor for determination of nitrate in water is reported for the first time. The biosensor electrodes were modified by methyl viologen mediator mixed with nitrate reductase (NR) from Aspergillus niger by cross-linking with glutaraldehyde in the presence of bovine serum albumin and Nafion^® cation-exchange polymer. The process parameters for the fabrication of the enzyme electrode and various experimental variables such as pH, the enzyme loading and time of immobilization in glutaralaldehyde vapor were investigated with regard to their influence on sensitivity, limit of detection, dynamic range and operational and storage stability. The biosensor can reach 95% of steady-state conductance value in about 15 s. Linear calibration in the range of 0.02 and 0.25 mM with detection limits of 0.005 mM nitrate was obtained with a signal-to-noise ratio of 3. When stored in 5 mM phosphate buffer (pH 7.5) at 4 °C, the sensor showed good stability over 2 weeks.     

Characterization of different diamond-like carbon electrodes for biosensor design

Diamond-like carbon (DLC) films are gaining big interest in electrochemistry research area. DLC electrodes made with different ratio of sp³/sp² carbon hybridization or doped with different percentages of nickel were characterized electrochemically by cyclic voltammetry and by amperometric measurements towards hydrogen peroxide. SiCAr1 and SiCNi5% were chosen as sensitive transducers for the elaboration of amperometric glucose biosensors. Immobilization of glucose oxidase was carried out by cross-linking with glutaraldehyde. Measurements were made at a fixed potential + 1.0 V in 40 mM phosphate buffer pH 7.4. SiCAr1 seems to be more sensitive for glucose, 0.6875 μA/mM, than SiCNi5%, 0.3654 μA/mM. Detections limits were 20 μM and 30 μM, respectively. Apparent Michaelis-Menten constants were found around 3 mM. Forty-eight percent and 79% of the original response for 0.5 mM glucose remained after 10 days for both biosensors, respectively.     

Development and evaluation of electrochemical glucose enzyme biosensors based on carbon film electrodes

Electrochemical glucose enzyme biosensors have been prepared on carbon film electrodes made from carbon film electrical resistors. Evaluation and characterisation of these electrodes in phosphate buffer saline solution has been carried out with and without pretreatment by cycling in perchloric acid or at fixed applied potential. Both pretreatments led to a reduction in the carbon surface oxidation peak and enabled better detection of hydrogen peroxide in the pH range of 5-7. Glucose oxidase enzyme was immobilised on the carbon surface by mixing with glutaraldehyde, bovine serum albumin and with and without Nafion. The performance of these two types of electrode was similar, that containing Nafion being more physically robust. Linear ranges were up to around 1.5 mM, with detection limits 60 μM, and pretreatment of the carbon film electrode at a fixed potential of +0.9 V versus SCE for 5 min was found to be the most beneficial. Michaelis-Menten constants between 5 mM and 10 mM were found under the different experimental conditions. Coating the immobilised enzyme layer with a thin layer of Nafion was found to give similar results in the determination of glucose to mixing it but with benefits against interferences for the analysis of complex matrices, such as wine. Potentialities, for a short-term-use or disposable sensors, are indicated.     

An improved biosensor for acetaldehyde determination using a bienzymatic strategy at poly(neutral red) modified carbon film electrodes

Improved biosensors for acetaldehyde determination have been developed using a bienzymatic strategy, based on a mediator-modified carbon film electrode and co-immobilisation of NADH oxidase and aldehyde dehydrogenase. Modification of the carbon film electrode with poly(neutral red) mediator resulted in a sensitive, low-cost and reliable NADH detector. Immobilisation of the enzymes was performed using encapsulation in a sol-gel matrix or cross-linking with glutaraldehyde. The bienzymatic biosensors were characterized by studying the influence of pH, applied potential and co-factors. The sol-gel and glutaraldehyde biosensors showed a linear response up to 60 μM and 100 μM, respectively, with detection limits of 2.6 μM and 3.3 μM and sensitivities were 1.7 μA mM⁻¹ and 5.6 μA mM⁻¹. The optimised biosensors showed good stability and good selectivity and have been tested for application for the determination of acetaldehyde in natural samples such as wine.     

Electrocatalytic reduction of dioxygen at the surface of glassy carbon electrodes modified by calix[6]arene-methyl viologen

The preparation and electrochemical characterization of glassy carbon electrodes modified with calixarene-methyl viologen (MV) were investigated. The intermolecular complex of calix[6]arene and MV has an electrocatalytic effect on oxygen reduction. The cyclic voltammograms of the electroreduction of oxygen showed an enhanced current peak at approximately −0.60 V in air-saturated phosphate buffer. The experimental parameters were optimized and the mechanism of the catalytic process was discussed.     

Direct electrochemistry of glucose oxidase based on its direct immobilization on carbon ionic liquid electrode and glucose sensing

Direct electrochemistry of glucose oxidase (GOx) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE) with a conductive hydrophobic ionic liquid, 1-butyl pyridinium hexafluophosphate ([BuPy][PF₆]) as binder for the first time. A pair of reversible peaks is exhibited on GOx/CILE by cyclic voltammetry. The peak-to-peak potential separation (ΔE_P) of immobilized GOx is 0.056 V in 0.067 M phosphate buffer solution (pH 6.98) with scan rate of 0.1 V/s. The average surface coverage and the apparent Michaelis–Menten constant are 6.69 × 10⁻¹¹ mol·cm⁻² and 2.47 μM. GOx/CILE shows excellent electrocatalytic activity towards glucose determination in the range of 0.1–800 μM with detection limit of 0.03 μM (S/N = 3). The biosensor has been successfully applied to the determination of glucose in human plasma with the average recoveries between 95.0% and 102.5% for three times determination. The direct electrochemistry of GOx on CILE is achieved without the help of any supporting film or any electron mediator. GOx/CILE is inexpensive, stable, repeatable and easy to be fabricated.     

Amperometric glucose biosensor based on a gold nanorods/cellulose acetate composite film as immobilization matrix

We report on the utilization of gold nanorods to create a highly responsive glucose biosensor. The feasibility of an amperometric glucose biosensor based on immobilization of glucose oxidase (GOx) in gold nanorod is investigated. GOx is simply mixed with gold nanorods and cross-linked with a cellulose acetate (CA) medium by glutaraldehyde. The adsorption of GOx on the gold nanorods is confirmed by X-ray photoelectron spectroscopy (XPS) measurements. Circular dichroism (CD) and UV-spectrum results show that the activity of GOx was preserved after conjugating with gold nanorods. The current response of modified electrode is 10 times higher than that of without gold nanorods. Under optimal conditions, the biosensor shows high sensitivity (8.4 μA cm⁻² mM⁻¹), low detection limit (2 × 10⁻⁵ M), good storage stability and high affinity to glucose (). A linear calibration plot is obtained in the wide concentration range from 3 × 10⁻⁵ to 2.2 × 10⁻³ M.     

Amperometric enzyme electrodes of glucose and lactate based on poly(diallyldimethylammonium)-alginate-metal ion-enzyme biocomposites

Sodium alginate (AlgNa) and poly(diallyldimethylammonium chloride) (PDDA) were mixed to obtain an interpenetrating polymer composite via electrostatic interaction and then cast on an Au electrode surface, followed by incorporation of metal ions (e.g. Fe³⁺ or Ca²⁺, to form AlgFe or AlgCa hydrogel) and glucose oxidase (GOx) (or lactate oxidase (LOx)), to prepare amperometric enzyme electrodes. The interactions of PDDA, Alg, and Fe³⁺ are studied by visual inspection as well as microscopic and electrochemical methods. Under optimized conditions, the PDDA-AlgFe-enzyme/Au and PDDA-AlgCa-enzyme/Au electrodes can give good analytical performance (e.g. nM-scale limit of detection of glucose or lactate, and sensitivities > 50 μA cm⁻² mM⁻¹) in the first-generation biosensing mode, which are better than the reported analogs using typical polysaccharide biopolymers as enzyme-immobilization matrices. The enzyme electrodes also worked well in the second-generation biosensing mode in the coexistence of p-benzoquione or ferrocene monocarboxylic acid artificial mediator. Biofuel cells (BFCs) with the enzyme electrodes as the bioanodes and glucose (or lactate) as the biofuel were also fabricated with satisfactory results. The proposed protocols for preparation of high performance Alg-based biocomposites may find wide applications in bioanalysis.     

Amperometric phenol biosensor based on sol-gel silicate/Nafion composite film

An amperometric biosensor based on tyrosinase immobilized in silicate/Nafion composite film has been developed for the determination of phenolic compounds. The Nafion polymer in the composite was used not only to overcome the brittleness of the pure sol-gel-derived silicate film but also to increase the long-term stability of the biosensor. Tyrosinase was immobilized by a thin film of silicate/Nafion composite on a glassy carbon electrode. Phenolic compounds were determined by the direct reduction of biocatalytically-liberated quinone species at −200 mV versus Ag/AgCl (3 M NaCl). The process parameters for the fabrication of the enzyme electrode and various experimental variables such as pH and operating potential were explored for optimum analytical performance of the enzyme electrode. The biosensor can reach 95% of steady-state current in about 15 s. The sensitivities of the biosensor for catechol and phenol were 200 and 46 mA/M, respectively. A detection limit of 0.35 mM catechol was obtained with a signal-to-noise ratio of 3. The enzyme electrode retained 74% of its initial activity after 2 weeks of storage in 50 mM phosphate buffer at pH 7.     

Amperometric glucose biosensor based on boron-doped carbon nanotubes modified electrode

Doped carbon nanotubes are now extremely attractive and important nanomaterials in bioanalytical applications due to their unique physicochemical properties. In this paper, the boron-doped carbon nanotubes (BCNTs) were used in amperometric biosensors. It has been found that the electrocatalytic activity of the BCNTs modified glassy carbon (GC) electrode toward the oxidation of hydrogen peroxide is much higher than that of the un-doped CNTs modified electrode due to the large amount of edge sites and oxygen-rich groups located at the defective sites induced by boron doping. Glucose oxidase (GOD) was selected as the model enzyme and immobilized on the BCNTs modified glassy carbon electrode by entrapping GOD into poly(o-aminophenol) film. The performance of the sensor was investigated by electrochemical methods. At an optimum potential of +0.60 V and pH 7.0, the biosensor exhibits good characteristics, such as high sensitivity (171.2 nA mM(-1)), low detection limit (3.6 microM), short response time (within 6s), satisfactory anti-interference ability and good stability. The apparent Michaelis-Menten constant (K(m)(app)) is 15.19 mM. The applicability to the whole blood analysis of the enzyme electrode was also evaluated.     

A new,improved sensor for ascorbate determination at copper hexacyanoferrate modified carbon film electrodes

A new, improved sensor for the electrocatalytic determination of ascorbate has been developed that has both a low applied operating potential and a low detection limit. The sensor was constructed by depositing copper hexacyanoferrate film either electrochemically or chemically onto carbon film electrode, and it was then characterised by cyclic voltammetry and electrochemical impedance spectroscopy. Chemically deposited films were shown to be the best for ascorbate determination and were used as an amperometric sensor at +0.05 V versus SCE to determine ascorbate in wines and juice. The linear range extended to 5 mM with a limit of detection of 2.1 M, the sensor was stable for more than four months, and it could be used continuously for at least 20 days.     

Development of Novel Glucose and Pyruvate Biosensors at Poly(Neutral Red) Modified Carbon Film Electrodes. Application to Natural Samples

Amperometric biosensors based on the corresponding oxidase enzyme with poly(neutral red) redox mediator have been developed for the determination of glucose and pyruvate. The enzymes have been immobilized on top of poly(neutral red) modified carbon film electrodes with glutaraldehyde as the cross‐linking agent. The biosensors were characterized by cyclic voltammetry and by electrochemical impedance spectroscopy. The glucose biosensor exhibited a linear response in the range 90 μM to 1.8 mM with a detection limit of 22 μM and the pyruvate biosensor in the range 90 to 600 μM with a detection limit of 34 μM. The relative standard deviations were found to be 2.1% (n=3) and 2.8% (n=4) respectively. The interference effects of various compounds were also studied. The glucose content of several types of wine and the amount of pyruvate in onion and garlic were determined and the results were compared with those obtained by standard spectrophotometric methods.     

A study of uricase biosensor based on a glassy carbon electrode modified with Nafion and methyl viologen

A uricase biosensor was constructed by using bovine serum albumin and glutaraldehyde as cross linker to immobilize uricase on a glassy carbon electrode modified with Nafion and methyl viologen (MV). A linear response of uric acid in serum was observed in a range of 1.0·10^–3 to 5.0·10^–6 mol/1 and the response time is 25 s. This biosensor has the advantage of high sensitivity, fast response as compared with previous sensors and low interferences.     

Biocomposites of covalently linked glucose oxidase on carbon nanotubes for glucose biosensor

The formation of covalently linked composites of multi–walled carbon nanotubes (MWCNT) and glucose oxidase (GOD) with high-function density for use as a biosensing interface is described. The reaction intermediates and the final product were characterized by using FT–IR spectroscopy, and the MWCNT-coated GOD nanocomposites were examined by atomic force microscopy (AFM) and transmission electron microscopy (TEM). Interestingly, it was found that the GOD–MWCNT composites are highly water soluble. Electrochemical characterization of the GOD–MWCNT composites that were modified on a glassy carbon electrode shows that the covalently linked GOD retains its bioactivity and can specifically catalyze the oxidation of glucose. The oxidation current shows a linear dependence on the glucose concentration in the solution in the range of 0.5–40 mM with a detection limit of 30 μM and a detection sensitivity of 11.3 μA/mMcm². The present method may provide a way to synthesize MWCNT related composites with other biomolecules and for the construction of enzymatic reaction-based biofuel cells and biosensors. Supported by grants from the National Natural Science Foundation of China (NSFC, No. 20125515; 90206037; 20375016) and the Natural Science Foundation of Jiangsu Province (Grant No. BK 2004210)     

Evaluation of an amperometric glucose biosensor based on a ruthenium complex mediator of low redox potential

An amperometric glucose ring-disk biosensor based on a ruthenium complex mediator of low redox potential was fabricated and evaluated. This thin-layer radial flow microsensor (10 μl) with ring-disk working electrode displayed remarkable amperometric sensitivity. For Ru₃(μ₃-O)(AcO)₆(Py)₃(ClO₄) (Ru-Py), a trinuclear oxo-acetate bridged cluster, a reversible redox curve of low redox potential and narrow potential window (redox potentials were −0.190 and −0.106 V versus Ag/AgCl wire, respectively) was observed, which is comparable to many reported mediators such as ferrocene derivatives and other ruthenium complexes. The glucose and hydrogen peroxide assays were carried out with this complex-modified electrode Ru-Py-HRP-GOx/Nafion. The sensitivity was obtained 24 nA (15.4 mA M⁻¹ cm⁻²) for 10 μM glucose and 126 nA (160 mA M⁻¹ cm⁻²) for 5 μM H₂O₂, respectively with a working potential at 0 V versus Ag/AgCl. Ascorbic acid was studied as interference to the glucose assay. The application of 0 V potential versus Ag/AgCl did not avoid the occurrence of the oxidation of ascorbic acid, however, the pre-coating of ascorbate oxidase on the disk part of the ring-disk working electrode efficiently pre-oxidized the ascorbic acid and hence eliminated its interference on the glucose response. The practical reliability was also evaluated by assaying the dialysate from the prefrontal cortex of Wistar rats.     

硫堇-牛血清白蛋白氧化还原复合膜修饰葡萄糖生物传感器的研究

通过交联法和自组装法制备了一种双酶型葡萄糖生物传感器.首先以牛血清白蛋白-戊二醛为交联剂以实现对辣根过氧化物酶(HRP)的固载,再利用凝集素-糖蛋白的识别作用将葡萄糖氧化酶(GOD)分子组装到电极表面,制得双酶型的葡萄糖生物传感器.采用原子力显微镜(AFM)考察了复合膜的性质,同时采用循环伏安法和计时电流法考察了该传感...     

New biosensing platforms based on the layer-by-layer self-assembling of polyelectrolytes on Nafion/carbon nanotubes-coated glassy carbon electrodes

We are proposing for the first time the use of a Nafion/multi-walled carbon nanotubes dispersion deposited on glassy carbon electrodes (GCE) as a new platform for developing enzymatic biosensors based on the self-assembling of a chitosan derivative and different oxidases. The electrodes are obtained by deposition of a layer of Nafion/multi-wall carbon nanotubes dispersion on glassy carbon electrodes, followed by the adsorption of a chitosan derivative as polycation and glucose oxidase, l-aminoacid oxidase or polyphenol oxidase, as polyanions and biorecognition elements. The optimum configuration for glucose biosensors has allowed a highly sensitive (sensitivity = (0.28 ± 0.02) μA mM⁻¹, r = 0.997), fast (4 s in reaching the maximum response), and highly selective (0% interference of ascorbic acid and uric acid at maximum physiological levels) glucose quantification at 0.700 V with detection and quantification limits of 0.035 and 0.107 mM, respectively. The repetitivity for 10 measurements was 5.5%, while the reproducibility was 8.4% for eight electrodes. The potentiality of the new platform was clearly demonstrated by using the carbon nanotubes/Nafion layer as a platform for the self-assembling of l-aminoacid oxidase and polyphenol oxidase. Therefore, the platform we are proposing here, that combines the advantages of nanostructured materials with those of the layer-by-layer self-assembling of polyelectrolytes, opens the doors to new and exciting possibilities for the development of enzymatic and affinity biosensors using different transdution modes.