全钒液流电池用磺化聚醚醚酮/锂皂石质子膜的结构及性能

通过溶液流延法制备了磺化聚醚醚酮/锂皂石(SPEEK/Lap)复合膜, 对其物理化学性质、 机械性能、 化学稳定性及单电池性能进行了测试. 在SPEEK基质中引入的Lap有效改善了复合膜的质子传导率、 溶胀率和机械性能. 当Lap添加量(质量分数)从0.2%增到1.5%时, 复合膜的质子传导率随之增加(19.9~23.6 mS/cm). SPEEK/Lap-0.2复合膜的自放电时间为57.2 h, 是Nafion 117膜的2.4倍和纯SPEEK膜的1.5倍. 在80 mA/cm ²电流密度下, SPEEK/Lap-0.2复合膜的电压效率(VE, 86.5%)和能量效率(EE, 84.0%)明显高于Nafion 117膜(VE: 83.8%, EE: 80.7%)和纯SPEEK膜(VE: 81.4%, EE: 78.9%). 同时, SPEEK/Lap-0.2复合膜经100次充放电循环测试后具有良好的循环稳定性和结构稳定性.     

新型十二烷基三甲氧基硅烷/氧化石墨烯复合膜对430不锈钢耐蚀性能的影响

使用一步电沉积法在430不锈钢上制备出十二烷基三甲氧基硅烷(DTES)/氧化石墨烯(GO)复合膜。 拉曼光谱(Raman)与扫描电子显微镜(SEM)测试表明,氧化石墨烯均匀地混合在硅烷膜中,并用电化学交流阻抗与极化曲线方法对这种复合膜所保护的430不锈钢进行耐蚀性能测试。 结果显示,在3.5%NaCl溶液中,430不锈钢会发生腐蚀反应,而存在硅烷复合膜的430不锈钢的耐蚀性能显著地提高。 研究表明,由于氧化石墨烯出色的阻隔性能一定程度上弥补了硅烷膜的缺陷,而且延长了腐蚀介质通过硅烷基质的路径,因此复合膜有着对基底物质更强的保护性能。     

TiO2/氧化石墨烯光催化降解亚甲基蓝性能研究

理想的石墨烯具有二维平面结构,其具有良好的机械性能、热导率、高电子迁移率和量子霍尔效应。本文以改进的Hummers法制得氧化石墨烯(Graphene Oxide),超声处理和水热法制备了氧化石墨烯(GO)负载量分别为1.0 wt%、1.5 wt%,2.0 wt%,2.5 wt%的TiO_2/GO复合材料,并通过XRD、TEM等表征手段观察了复合材料的晶相和结构,探讨光催化降解亚甲基蓝性能。结果表明:较之TiO_2,复合材料均具有更大的表面积、更好的亲水性和更强的光催化性能;反应浓度均为2 g·L~(-1)的复合材料,光催化降解10 ppm亚甲基蓝,氧化石墨烯负载量为1.5 wt%的TiO_2/GO复合材料,1 h光催化降解率可达86%,效果最佳。TiO_2/GO复合材料吸附容量大,稳定性良好,能够高效光催化降解偶氮型染料,有望在进一步改良性能后广泛应用于降解工业废水领域。     

氧化石墨烯/聚合物复合质子交换膜研究进展

氧化石墨烯/聚合物复合质子交换膜(GO/Polymer blend PEM)是一种新型的质子交换膜,广泛应用于直接甲醇燃料电池(DMFC)中,已成为质子交换膜研究的热点之一。氧化石墨烯/聚合物复合质子交换膜具有较高的传导质子率、力学性能、阻醇性能和电池性能。本文综述了氧化石墨烯(GO)处理方法、氧化石墨烯/聚合物复合质子交换膜制备方法,氧化石墨烯/聚合物复合质子交换膜的质子传导、阻醇、离子交换容量和电池的性能,氧化石墨烯/聚合物复合质子交换膜质子传递机理及阻醇机理。     

聚甲基乙撑碳酸酯/氧化石墨烯纳米复合材料的制备及性能研究

本文采用改进Hummers法制备氧化石墨烯(GO),通过原子力显微镜对GO片层形貌进行表征;以聚甲基乙撑碳酸酯(PPC)、聚乙烯醇(PVA)和氧化石墨烯(GO)为原料,采用溶液和熔融共混法相结合,制备PPC/PVA/GO纳米复合材料,研究其力学性能、热学性能和动态流变行为。结果表明,当GO含量为0.5 wt%时,拉伸强度达到了22.03 MPa,与纯PPC相比提高了25.8%;当GO含量增大到1.0 wt%时,拉伸强度开始降低;断裂伸长率随GO的加入呈现降低的趋势。GO含量为1.0%时复合材料的热学性能最好,与纯PPC相比,复合材料的完全热分解温度从350℃提高到了400℃以上,并且热分解速率下降了12%/min;复合材料的复数黏度、储能模量和损耗模量随PVA及GO的引入也有一定程度的提高。     

热处理工艺对静电纺丝制备PVDF/PMMA复合膜的力学性能的影响

利用热处理工艺对静电纺丝制备复合膜聚偏氟乙烯/聚甲基丙烯酸甲酯(PVDF/PMMA)进行改性,研究不同温度与不同压力对复合膜力学性能的影响,并与商用膜Celgard 2400在力学性能、离子电导率、循环性能方面进行对比。结果表明:在温度145℃,压强0.05 MPa时,PVDF/PMMA复合膜的拉伸强度为19.0 MPa,是未加压处理时其拉伸强度的10倍;PVDF/PMMA复合膜室温下的离子电导率为1.180mS/cm,比商用膜室温下的离子电导率高出187%;由PVDF/PMMA复合膜组装的纽扣电池在0.2C倍率下的放电比容量为140 (mA·h)/g,在1C倍率下的放电比容量为130(mA·h)/g,与商用膜同倍率下的放电比容量相同;在5C倍率下PVDF/PMMA复合膜的循环性能更优。     

氧化石墨烯改性ZnO/CeO2复合纳米材料的制备及其紫外屏蔽性能研究

以六水硝酸锌、六水硝酸铈、氧化石墨烯为原料,采用溶胶凝胶法制备了氧化石墨烯(GO)改性ZnO/CeO_2复合纳米紫外屏蔽剂。采用X射线衍射(XRD)、扫描电镜(SEM)、傅立叶变换红外光谱(FTIR)、紫外可见分光光度计(UV-Vis)等测试手段对产物的结构、组成及形貌进行表征,研究了氧化铈与氧化锌摩尔比、GO投入量、屏蔽剂用量以及pH值对复合纳米材料紫外屏蔽性能的影响,探索了氧化石墨烯改性ZnO/CeO_2复合纳米的最佳制备条件。结果表明:氧化石墨烯改性ZnO/CeO_2复合纳米材料中GO、CeO_2、ZnO的平均粒径分别为8. 3、15. 4、37. 5 nm。当pH 6. 0、氧化铈与氧化锌摩尔比为4∶1、GO投入量为2. 0g、屏蔽剂用量为0. 06 g/L时,紫外屏蔽性能强弱顺序为:氧化石墨烯改性ZnO/CeO_2复合纳米材料 GOZnO/CeO_2复合纳米材料 CeO_2 ZnO。     

Mn3O4/石墨烯复合材料的制备与电化学性能研究

本文以氧化石墨烯（GO）溶液为氧化剂,采用水热法使GO直接氧化Mn(Ac)₂制备Mn₃O₄/石墨烯复合材料,并通过在制备过程中加入氨水提高了复合材料中GO的还原程度与Mn₃O₄颗粒的分散性. 制得的Mn₃O₄/石墨烯复合材料表现出优异的电化学性能. 在0.5 A·g^-1的电流密度下复合材料质量比容量可达到850 mAh·g^-1,0.5 A·g^-1时充放电循环测试200周容量保持率为99%.     

部分还原氧化石墨烯-Fe3O4对水中Mn(Ⅱ)的快速去除

采用改进的Hummers法制备了氧化石墨烯(GO), 继而用一步共沉淀法制备了部分还原氧化石墨烯-四氧化三铁复合物(PRGO-Fe₃O₄). 采用X射线衍射(XRD)、 场发射扫描电子显微镜(FESEM)、 X射线能量色散光谱(EDX)、 高分辨透射电子显微镜(HRTEM)、 选区电子衍射(SAED)及傅里叶变换红外光谱(FTIR)等技术对其进行了分析表征; 考察了pH值、 接触时间、 吸附材料用量、 共存物质、 GO的还原、 循环使用次数等因素对Mn(Ⅱ)吸附行为的影响. 结果表明, PRGO-Fe₃O₄中Fe₃O₄颗粒分布均匀, 大小为15~20 nm, 剩磁和矫顽力均很小. 因Fe₃O₄颗粒的锚定作用, 石墨烯片层很薄, 使PRGO-Fe₃O₄对Mn(Ⅱ)表现出高效的吸附性能和良好的循环使用性能: 当pH=7、 PRGO-Fe₃O₄用量为500 mg/g时, 对201.3211 mg/L的Mn(Ⅱ)溶液仅3 min即达吸附平衡, 吸附率和吸附量分别为99.35%和404.49 mg/g, 磁分离仅需10 s, 经5次循环吸附后, 容量保持率为首次的78%. 机理与热力学研究结果表明, 吸附为吸热、 自发的单层化学吸附.     

功能型单层石墨烯的热剥离法制备及其超电容性能

以氧化石墨(GO)作为前驱体,在两种不同热剥离温度下制备了两类功能型单层石墨烯.其中第一类功能型单层石墨烯通过在较低温度及空气气氛下热剥离GO制备;第二类功能型单层石墨烯通过在氮气保护下高温热剥离GO得到;利用氮气吸附-脱附方法测定了两类样品的比表面积,利用电化学测试方法分析了其超电容性能.结果表明,通过低温热剥离的方式即可以有效剥离GO;两类样品均具有较高的BET比表面积.低温热剥离GO所制备的功能型单层石墨烯在2 mol/L KOH体系中的最大比电容值约为220 F/g;而通过高温热剥离GO所制备的功能型单层石墨烯虽然同样具有较高的BET比表面积,但其最大比电容值下降至约150 F/g.这表明通过低温热剥离GO所制备的功能型单层石墨烯具有更优异的超电容性能.     

Chitin/graphene oxide composite films with enhanced mechanical properties prepared in NaOH/urea aqueous solution

Chitin/graphene oxide (GO) composite films with excellent mechanical properties were prepared in NaOH/urea solution using a freezing/thawing method. The structure, thermal stability and mechanical properties of the composite films were investigated. Use of an atomic force microscope and transmission electron microscopy indicated that GO was successfully exfoliated to a single layer by ultrasonication. The results revealed that GO nanosheets were homogeneously dispersed and embedded in the chitin matrix. Due to the strong interactions between GO and the chitin matrix, the tensile strength and elongation at break of the composite film possessing 1.64 wt% GO were significantly improved by 98.7 and 114.5 %, respectively, compared with pure chitin film.     

Development of PE/PCL Bilayer Films Modified with Casein and Aluminum Oxide

The studied samples were prepared from polyethylene (PE) polymer which was coated with modified polycaprolactone (PCL) film in order to obtain bilayer films. Thin PCL film was modified with casein/aluminum oxide compound to enhance vapor permeability as well as mechanical and thermal properties of PE/PCL films. Casein/aluminum oxide modifiers were used in order to achieve some functional properties of polymer film that can be used in various applications, e.g., reduction of water vapor permeability (WVTR) and good mechanical and thermal properties. Significant improvement was observed in mechanical properties, especially in tensile strength as well as in water vapor values. Samples prepared with aluminum oxide particles indicated significantly lower values up to 60%, and samples that were prepared with casein and 5% Al₂O₃ showed the lowest WVTR value.     

紫外光固化的聚氨酯－丙烯酸酯－纤维素复合膜

再生纤维素膜(甘蔗渣浆制)表面直接用紫外光固化聚氨酯-丙烯酸酯制备出防水性复合膜。由红外光谱和扫描电镜研究了复合膜的结构。同时,测定了膜的防水性、力学性能、水汽透过性和尺寸稳定性。实验结果表明,当聚氨酯：丙烯酸酯为40:55(质量比),在400W紫外光下固化5min制得的复合膜具有致密的表面结构和较好的性能,该膜经水浸泡后其断裂强度可达干膜的90%,浸水收缩率和膨胀率均小于2.5%,水汽渗透量仅为再生纤维素膜的1/4.由此表明复合膜的防水性和尺寸稳定性明显提高。此外,该复合膜在可见光区的透光率在80%～90%之间,而且对紫外光有屏蔽作用。     

高醚化三聚氰胺甲醛树脂交联水性聚氨酯的制备与表征

合成了高醚化三聚氰胺甲醛树脂(HMMM)交联改性含聚乙二醇单甲醚(Ymer N120)亲水基团的阴离子型水性聚氨酯。 通过全反射红外(ATR-FTIR)、差示扫描量热仪(DSC)、电子拉力机等技术手段表征了改性后的水性聚氨酯胶膜结构、热性能和力学性能。 结果表明,随着HMMM质量分数的增加,聚氨酯胶膜中氢键相互作用减弱,胶膜耐热性、耐水性、拉伸强度、粘接性均有所提高;当HMMM为8%时,聚氨酯胶膜的拉伸强度增加了125%,T-型剥离强度增加了7.4 N/cm,硬段最大热分解速率对应温度增加了38 ℃。 此外,交联水性聚氨酯胶膜的耐水性也得到了很大程度的提高。     

气相生长碳纤维/形状记忆聚氨酯复合薄膜的力学及形状记忆性能研究

采用溶液混合法制备了不同含量的气相生长碳纤维(VGCF)增强形状记忆聚氨酯(SMPU)的复合材料薄膜,测试分析了纯SMPU及VGCF/SMPU复合材料薄膜的力学性能及形状记忆性能.结果表明,制得的复合材料薄膜在VGCF含量达到9 wt%时,VGCF在SMPU基体中仍具有较好的分散性;SMPU与VGCF复合后,得到的复合材料薄膜的拉伸强度和刚度有较大程度的提高,含量达到9 wt%时复合材料薄膜的拉伸强度比纯SMPU提高66%,弹性模量提高300%,储能模量也有较大程度提高;SMPU与VGCF复合后,形状记忆性能有一定的下降,但经过适当预处理后,其形状记忆性能可以基本接近纯SMPU.     

Nanocrystalline cellulose acetate (NCCA)/graphene oxide (GO) nanocomposites with enhanced mechanical properties and barrier against water vapor

Highly flexible nanocomposite films of nanocrystalline cellulose acetate (NCCA) and graphene oxide (GO) were synthesized by combining NCCA and GO sheets in a well-controlled manner. By adjusting the GO content, various NCCA/GO nanocomposites with 0.3–1 wt% GO were obtained. Films of these nanocomposites were prepared using the solvent casting method. Microscopic and X-ray diffraction (XRD) measurements demonstrated that the GO nanosheets were uniformly dispersed in the NCCA matrix. Mechanical properties of the composite films were also studied. The best GO composition of the samples tested was 0.8 wt%, giving tensile strength of 157.49 MPa, which represents a 61.92 % enhancement compared with NCCA. On the other hand, the composite films showed improved barrier properties against water vapor. This simple process for preparation of NCCA/GO films is attractive for potential development of high-performance films for electrical and electrochemical applications.     

Thermal,mechanical and water barrier properties of graphene oxide/polyvinyl alcohol/polyol composite films

The novel polymer composite of polyvinyl alcohol (PVA), polyol(PO) and graphene oxide (GO) was used to prepare the PVA/PO and GO/PVA/PO with different weight percents of GO (0.5 and 1% denoted as (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO, respectively) through solution casting blend technique. The structure–properties of all used films were confirmed by scanning electron microscope (SEM), Transmission Electron Microscope (TEM), X-ray powder diffraction (XRD), thermogravimetric analysis (TGA) and mechanical properties. The SEM results exhibited the uniform and homogeneous dispersion of GO in the PVA/PO blend matrix. The TEM and XRD analysis confirmed the structure and exfoliation of GO nanosheets, respectively. Thermal stability suggested that (0.5 wt%)GO/PVA/PO and (1 wt%) GO/PVA/PO films are more stable than PVA/PO. The tensile strength of (0.5 wt%)GO/PVA/PO and (1 wt%)GO/PVA/PO films reached 270.5% and 1349.6%, respectively, which are higher than that of the PVA/PO film. The decrease in the water absorption (WA) of GO/PVA/PO was found from 110.5 to 38.4%. The physico-mechanical properties of used films suggested that the prepared GO/PVA/PO blend composite films can be applied in food packaging areas.     

壳聚糖氧化自组装膜的制备及其性能

由高碘酸钠和壳聚糖溶液反应,成功制备出壳聚糖氧化自组装膜。采用傅立叶变换红外光谱(FTIR)和X射线衍射法对氧化自组装膜进行了结构表征,并对膜的吸水率及其力学性能进行了测试。当壳聚糖为3 g,而高碘酸钠加入量等于0.010 g时,得到壳聚糖氧化自组装膜的最佳的抗张强度,干膜为54.32 MPa,湿膜为29.11 MPa,相对壳聚糖膜分别提高了17.52%和26.78%;并且得到了最佳的阻水性,其吸水率为78.51%,相对于壳聚糖膜降低了6.88%。     

Evaluation of Mechanical Properties and Water Vapor Permeability in Chitosan Biofilms Using Sorbitol and Glycerol

Summary: Chitosan biofilms were prepared with and without plasticizer (glycerol and sorbitol). The physical and mechanical properties of chitosan biofilms with and without plasticizer were evaluated. Chitosan was obtained from shrimp wastes and characterized. The film forming solution (FFS) was obtained through chitosan dissolution and drying. The solution had its pH adjusted to 6.0 and oven dried (40 °C, 24 h) with forced air circulation. Chitosan biofilms without plasticizer showed a tensile strength about 36% higher than biofilms produced with plasticizer. On the other hand, biofilms with plasticizer presented superior values of elongation. The permeability of the water vapor and color presented significant difference (p < 0.05) between all biofilms. Chitosan/plasticizer biofilms showed higher values of water vapor permeability in relation to chitosan biofilms without plasticizer.     

Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

The aim of this study was to investigate physical and mechanical properties of graphene oxide (GO)/polyethersulfone (PES) nanocomposite films. The films were produced by solution casting method. The mechanical properties of composite films were evaluated by tensile test. A significant enhancement in the mechanical properties of neat PES films was obtained incorporating a small amount of GO loading (0.05–1 wt.%). The highest tensile strength was observed at 1 wt.% of GO. Comparisons were made between experimental data and the Halpin–Tsai model predictions for the tensile strength and modulus of GO/PES composites. The effect of an orientation factor on model predictions was also acquired. The hydrophilicity of the nanocomposite was evaluated by assessing contact angle and enhanced wet ability of the films was obtained with increasing the amount of GO up to 1%. The morphology of the nanocomposites was investigated using scanning electron microscopy and transmission electron microscopy and the results revealed a good dispersion of GO in the PES matrix. The thermal behavior of the composite was also studied. Thermal stability of composites was increased by adding the GO. Copyright © 2013 John Wiley & Sons, Ltd.