Influence of polymer matrix composition and architecture on polymer nanocomposite formation: Coarse-grained molecular dynamics simulation

Coarse-grained molecular dynamics simulations of stacks of two-dimensional platelets immersed in a polymer melt were performed to investigate aspects of the polymer matrix that promote the formation of intercalated or exfoliated nanocomposite structures. Such factors include temperature, copolymer architecture, and blend composition. Increasing the polymer-sheet attractive interaction led to binding of the sheets, where individual beads simultaneously attract two neighboring sheets, thus kinetically blocking intercalation by occupying the perimeter of the affected gallery. Polymers with a small polymer-sheet attraction, but having a strongly attractive chain end (end-functionalized polymers) minimized the bonding of adjacent sheets. These systems exhibited some sheet sliding because a majority of the confined polymer beads only interacted weakly with adjacent sheets; however, the number density of intercalated polymer was low. Mixtures of end-functionalized and nonfunctionalized polymers, however, yielded better intercalation efficiency. For the mixed system, the reduced number of highly attractive beads provided sufficient interaction for intercalation to occur, enabling greater intercalation rates, less sheet-bridging, and incorporation of the nonfunctionalized polymers into the galleries. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3272–3284, 2003     

Poly(dicyclopentadiene)‐montmorillonite nanocomposite formation via simultaneous intergallery‐surface initiation and chain crosslinking using ROMP

Exfoliated poly(dicyclopentadiene) (pDCPD)—montmorillonite (MMT) nanocomposites were synthesized via intergallery‐surface‐initiated ring opening metathesis polymerization (ROMP). This is the first example of in situ polymerization of pDCPD from clay intergallery surfaces using ROMP. Grubbs catalyst was immobilized on the surface of MMT clay modified with vinylbenzyl dimethyloctadecyl ammonium chloride (VOAC), and DCPD polymerized from the clay surface while simultaneously crosslinking to form a thermoset nanocomposite in a one‐pot reaction. X‐ray diffraction and transmission electron microscopy analysis indicated that the resultant nanocomposites exhibited exfoliated morphologies with heterogeneous clay platelet distribution. Conventional bulk‐initiated nanocomposites containing VOAC modified MMT were also synthesized as a comparison, and these resulted in nanocomposites with intercalated morphologies. The differences between the morphologies demonstrated that growing polymer chains from the initiator sites on the intergallery surface of the clay platelets pushed the platelets apart during the polymerization of the intergallery‐surface‐initiated nanocomposites, aiding in the exfoliation process. Compression testing indicated that the intergallery‐surface‐initiated nanocomposites led to improvements of up to 50% in the compressive Young's Modulus, while the bulk‐initiated nanocomposites at the same clay loadings did not exhibit improved properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Effect of nanoparticle network formation on electromagnetic properties and cell morphology of microcellular polymer nanocomposite foams

Adding high loadings of nanoparticles can remarkably alter the functionality of polymer nanocomposite foams. Therefore, this dramatic change was studied at the percolation threshold as a point to predict the properties of foamed nanocomposites using the viscoelastic characteristics of un-foamed ones. In this research, the effect of incorporating 10–40 wt% of ZnO nanoparticles on rheological properties of PS/ZnO samples was investigated. Then, these samples were foamed at processing temperatures of 80 and 120 °C to study morphology and electromagnetic properties. First, the rheological study showed that the storage modulus of nanocomposites increased significantly above 20 wt% of nanoparticles. A connected network of nanoparticles altered the microstructure of nanocomposite at this rheological percolation. The morphological results show a higher cell density for foamed samples above the rheological percolation. From electromagnetic properties, the effect of ZnO connected network is obvious on the absorption enhancement for 30 and 40 wt% and only for 40 wt% of ZnO at 80 and 120 °C, respectively. Therefore, the viscoelastic properties of samples are still dominant at the lower temperature, but the foam structure became more important at the higher temperatures. This shows that the role of the filler network faded at the higher temperature and electromagnetic properties were changed with the foam structure. The microstructure expansion results in the decrease of filler amount at a fixed volume of foams, so more filler fraction is required to form a connected network of nanoparticles.     

聚丙烯/PMMA/CaCO3纳米复合材料的制备、结构与力学性能

分别将经不同表面处理的纳米碳酸钙粒子与聚合物PP共混,制备PP／CaCO3和PP／PMMA／CaCO3纳米复合材料。用TEM观察了表面处理后纳米粒子的粒径与分散情况,发现复合粒子分散较均匀。用DSC与WAXD研究了复合材料的结晶行为,发现原位聚合制备的PMMA／CaCO3纳米复合粒子与PP共混后,PP有异相成核作用,出现了不稳定的PPβ晶型。PP／PMMA／CaCO3纳米复合材料力学性能有大幅度的提高。     

Validation of experimental results for graphene oxide-epoxy polymer nanocomposite through computational analysis

The change in interfacial interaction behavior of epoxy resin nanocomposites with the incorporation of graphene oxide (GO) was explored experimentally and computationally. GO with different weight (wt) loading was incorporated in epoxy resin by a three-way dispersion method. GO formed mechanical interlocking with epoxy resin, thereby resulting in a remarkable enhancement in mechanical and thermo-mechanical properties of GO-epoxy nanocomposite. In 0.3 wt% GO-epoxy nanocomposites, improvement of 26.7% in flexural strength and 39.2% in flexural modulus was reported. Using dynamic mechanical analysis (DMA), thermomechanical analysis (TMA) and differential scanning calorimetry (DSC), glass transition temperature (T_g) of 182.7°C and maximum thermal stability was reported for 0.3% GO-epoxy nanocomposite. The effect of GO on cross-linking in GO-epoxy nanocomposite was analyzed by DSC and Raman spectroscopy. The X-ray photoelectron spectroscopy (XPS) study was utilized to determine the interfacial interaction, and further was verified by density functional theory (DFT). By experimental and computational study, H-bonding was observed to improve interfacial interaction in GO-epoxy nanocomposite.     

Microfibrillated cellulose/cellulose acetate composites: Effect of surface treatment

Microfibrillated cellulose (MFC), which consists of a web‐like array of cellulose fibrils having a diameter in the range of 10–100 nm, was incorporated into a cellulose acetate (CA) matrix to form a totally biobased structural composite. Untreated and a 3‐aminopropyltriethoxysilane (APS) surface treated MFC was combined with a CA matrix by film casting from an acetone suspension. The effectiveness of the surface treatment was determined by infrared spectroscopy and X‐ray photoelectron spectroscopy. The Young's moduli of APS treated MFC composite films increase with increasing MFC content from 1.9 GPa for the CA to 4.1 GPa at 7.5 wt % of MFC, which is more than doubled. The tensile strength of the composite film increases to a maximum of 63.5 MPa at 2.5 wt % compared to the CA which has a value of 38 MPa. The thermal stability of composites with treated MFC is also better than the untreated MFC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 153–161, 2010     

Polyester resin and carbon nanotubes based nanocomposite as new-generation coating to prevent biofilm formation

In this article, we have developed protective nanocomposite coatings using unsaturated polyester resin and multiwalled carbon nanotubes showing antimicrobial activity and mechanical durability. Carbon nanotubes retain the mechanical resilience of polyester resin in the nanocomposite, improve its hydrophobic character, and increase the adhesion features of the coating, preventing its stiffness from decreasing due to water absorption or exposure to UV rays. Nanocomposite coating exhibits an appreciable antimicrobial property and a lower level of toxicity compared to pure resin. All these features make this material a good candidate for its use in the field of anti-biofilm coatings.     

Effect of thermal treatment of rice husk ash on the surface properties of hydrated lime-rice husk ash binders

Rice husk ash fired at different temperatures, 450, 700 and 1000°C, was mixed with different concentrations of lime (molar lime/silica ash ratio of 0.2, 0.5 and 1.0). Each dry mixture was first ground and hydrated in the suspension form (water/solid ratio = 10) for various time intervals within the range of 1 to 365 days. The surface properties of the unhydrated and hydrated samples were studied by means of nitrogen adsorption measurements. The results indicated that the surface areas and total pore volumes of unhydrated solid mixtures and hydrated lime-rice husk ash samples, prepared with lime/silica ash ratio of 1.0, decrease with increasing firing temperature of rice husk ash. The effect of varying the lime/silica ash ratio of the solid mixture on the surface area and pore structure was fully discussed. The results of surface area and pore volume measurements could also be related to the crystal structure of silica produced from rice husk ash.     

A novel method to introduce durable hydrophilicity onto hydrophobic polymer surface by plasma treatment

We have examined a novel method to fabricate a durable hydrophilic surface of hydrophobic polymeric materials modified by plasma treatment. The method involves a trapping of maleic anhydride-containing polymer onto poly(ethylene naphthalate) (PEN) by a plasma-induced crosslinking reaction of PEN followed by hydrolysis of maleic anhydride moiety to generate hydrophilic carboxyl groups on the PEN surface. In fact, the PEN film surface thus treated has shown an effective stability of wettability based on the water contact angle measurement.     

Electrical and optical properties of ceramic–polymer nanocomposite coatings

Transparent, conductive composite coatings were fabricated from suspensions of poly(vinyl acetate‐acrylic) (PVAc‐co‐acrylic) copolymer latices (50–600 nm) and nanosized antimony‐doped tin oxide (ATO) particles (～15 nm). The suspensions were deposited as coatings onto poly(ethylene terephthalate) substrates and dried at 50 °C. Microstructure studies using field emission scanning electron microscopy and tapping‐mode atomic force microscopy (TMAFM) indicated that the latex particles coalesced during drying and forced the ATO particles to segregate into the boundaries between the latex particles. Low phase contrast was observed with TMAFM; this result was consistent with the presence of PVAc‐co‐acrylic in the ATO‐rich phase of the composite. The conductivity of the composite coatings followed a percolation power‐law equation, with the percolation threshold between 0.05 and 0.075 volume fractions of ATO and the critical conductivity exponent ranging from 1.34 to 2.32. The highest direct‐current conductivity of the composite coatings was around 10^?2 S/cm. The optical transmittance and scattering behavior of the coatings were also investigated. Compared with the PVAc‐co‐acrylic coating, the composite coatings had lower transparency because of the Rayleigh scattering. The transparency of the composite coatings was improved by a reduction in the coating thickness. The best transparency for the coatings with a direct‐current conductivity of approximately 10^?2 S/cm was around 85% at a wavelength of 600 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1744–1761, 2003     

Thermal properties and flammability of fibres made from polyimidoamide nanocomposite

The effects of basic fibre-forming parameters on the thermal properties and flammability of fibres from polyimidoamide (PIA) nanocomposite have examined. The comparative analysis of the properties of fibres from modified PIA and PIA nanocomposite has been conducted. The multi-functional fibres prepared from PIA nanocomposite show increased porosity and sorption properties as well as a high thermal stability and reduced flammability in comparison with fibres without MMT.     

Study of hydrophilicity and stability of chemically modified PDMS surface using piranha and KOH solution

Successful realization of various BioMEMS devices demands effective surface modification techniques of PDMS elastomer. This paper presents a detailed report on a simple and cost effective approach for surface modification of PDMS films involving wet chemical treatment in two‐step processes: primarily involving piranha solution followed by KOH dip to improve hydrophilicity and stability of PDMS surface. Chemical composition of the solution and surface treatment condition have been varied and optimized to significantly increase the surface energy. The effect of surface modification of the elastomer after wet chemical treatment is analyzed using contact angle measurement and FTIR‐ATR study. PDMS surface treated in piranha solution with H₂O₂ and H₂SO₄ in the ratio of 2:3 followed by a dip in KOH solution for 15 min duration each, demonstrated a maximum reduction of contact angle to ～27° as compared to untreated sample having a contact angle of ～110°. The removal of hydrophobic methyl group from elastomer surface and subsequent hydrophilization of surface by wet chemical process was confirmed from FTIR‐ATR spectra. This result is also supported by improved adhesion and electrical continuity of deposited aluminum metal film over the modified PDMS surface. Copyright © 2011 John Wiley & Sons, Ltd.     

Green synthesis of polymer nanofibers and their composites as flame‐retardant materials for polymer nanocomposites

Polyaniline nanofibers and their composites with carbon nanotubes were developed as an effective flame‐retardant material using a facile green method. Polyaniline nanofibers were used as a smart flame‐retardant for acrylonitrile–butadiene–styrene polymer. The polyaniline nanofibers were dispersed in polymer matrix forming well‐dispersed polymer nanocomposites. Effect of polyaniline nanofiber mass ratio on the polymer nanocomposite properties was studied. Polyaniline nanofiber composites with carbon nanotubes were also dispersed in polymer matrix. The thermal stability and flammability properties of the polymer nanocomposites were investigated. The rate of burning of polymer nanocomposites achieved 82.5% reduction (7.32 mm/min) compared with virgin polymer (42.5 mm/min). The reduction in peak heat release rate and total heat release of the polymer nanocomposites containing nanofibers achieved 74 and 34%, respectively. Interestingly, the average mass loss rate was significantly reduced by 58% and the emission of carbon monoxide and carbon dioxide gases were suppressed by 20 and 47%, respectively. The effect of polyaniline nanofibers composites on the flammability of polymer nanocomposites was also studied. Polyaniline nanofibers and their composites were characterized using Fourier transform infrared spectroscopy and transmission and scanning electron microscopy. The dispersion of polyaniline nanofibers in polymer nanocomposites was characterized using transmission electron microscopy. The different polymer nanocomposites were characterized using thermogravimetric analysis, UL94 flame chamber, and cone calorimeter tests. Copyright © 2016 John Wiley & Sons, Ltd.     

The effect of annealing temperatures on surface properties,hydroxyapatite growth and cell behaviors of TiO2 nanotubes

Well‐ordered TiO₂ nanotubes were prepared by the electrochemical anodization of titanium in an ethylene glycol electrolyte containing 1 wt% NH₄F and 10 wt% H₂O at 20 V for 20 min, followed by annealing. The surface morphology and crystal structure of the samples were examined as a function of the annealing temperature by field emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD), respectively. Crystallization of the nanotubes to the anatase phase occurred at 450 °C, while rutile formation was observed at 600 °C. Disintegration of the nanotubes was observed at 600 °C and the structure vanished completely at 750 °C. Electrochemical corrosion studies showed that the annealed nanotubes exhibited higher corrosion resistance than the as‐formed nanotubes. The growth of hydroxyapatite on the different TiO₂ nanotubes was also investigated by soaking them in simulated body fluid (SBF). The results indicated that the tubes annealed to a mixture of anatase and rutile was clearly more efficient than that in their amorphous or plain anatase state. The in vitro cell response in terms of cell morphology and proliferation was evaluated using osteoblast cells. The highest cell activity was observed on the TiO₂ nanotubes annealed at 600 °C. Copyright © 2010 John Wiley & Sons, Ltd.     

Development of standards for reliable surface analyses by ISO technical committee 201 on surface chemical analysis

The need for reliable surface analyses together with quality‐management requirements for analytical laboratories led the International Organization for Standardization (ISO) to form its Technical Committee (TC) 201 on Surface Chemical Analysis in 1991. This article describes the organization of TC 201, the strategies that have been found useful for identifying and assessing possible projects for new international standards, and the 57 international standards and other documents prepared to date by TC 201. Standards have now been developed for Auger‐electron spectroscopy, glow‐discharge spectroscopy, various types of scanning probe microscopy, secondary‐ion mass spectrometry, sputter‐depth profiling, total‐reflection X‐ray fluorescence spectroscopy, X‐ray photoelectron spectroscopy, and X‐ray reflectometry. In addition, standards have been developed with definitions of terms used in surface chemical analysis; the handling, preparation of specimens for surface analysis; information and data‐transfer formats; and methods for determining the lateral resolution of beam‐based methods of surface analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Structure and properties of the nanocomposite films of chitosan reinforced with cellulose whiskers

Bio‐based nanocomposite films were successfully developed using cellulose whiskers as the reinforcing phase and chitosan as the matrix. Cellulose whiskers, with the lengths of 400 ± 92 nm and diameters of 24 ± 7.5 nm on average, were prepared by hydrolyzing cotton linter with sulfuric acid solution. The effects of whisker content on the structure, morphology and properties of the nanocomposite films were characterized by SEM, XRD, FTIR, UV‐vis spectroscopy, DMA, TG, tensile testing, and swelling experiment. The results indicated that the nanocomposites exhibited good miscibility, and strong interactions occurred between the whiskers and the matrix. With increasing whisker content from 0 to 15–20 wt %, the tensile strength of the composite films in dry and wet states increased from 85 to 120 MPa and 9.9 to 17.3 MPa, respectively. Furthermore, the nanocomposite films displayed excellent thermal stability and water resistance with the incorporation of cellulose whiskers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1069–1077, 2009     

Some aspects of AFM nanomechanical probing of surface polymer films

We analyzed how the approach developed for the microindentation of non-uniform elastic solids can be adapted to analyze the atomic force microscopy (AFM) probing of ultrathin (1-100 nm thick) polymer films on a solid substrate, as well as polymer films with a multilayered structure. We suggested that recent Johnson's modification of the contact mechanics model that included a viscoelastic contribution could also be utilized to analyze rate-dependent loading data for polymer surfaces. The graded model proposed for microindentation experiments was modified allowing to account not only for variable elastic moduli within different layers but also for the gradient of properties between layers within a transition zone. Two examples of a recent application of this model for molecularly thick hyperbranched polymer monolayers (<3 nm thick) and tri-layered polymer films (20-40 nm thick) tethered to a solid substrate were presented and discussed. In both cases, complex shapes of both loading curves and elastic modulus depth profiles obtained from experimental AFM data were successfully fitted by the graded model with realistic structural parameters.     

Mechanical and barrier properties of ternary nanocomposite films based on polycarbonate/amorphous polyamide blends modified with a nanoclay

Ternary polycarbonate (PC)/amorphous polyamide–nanoclay (naPA) nanocomposite (PC/naPA) films were obtained by melt mixing and drawing, and the effects of the naPA content and the draw ratio (DR) on the structure, morphology and mechanical and barrier properties were studied. Despite the presence of nanoclay, the films exhibited a negligible roughness and the excellent optical properties of PC and amorphous polyamide (aPA). The dispersed naPA phase was pure and small, indicating compatibility. The naPA did not hinder the drawing ability of PC. At low DRs the dispersed phase was elongated and oriented along the machine direction (extrusion flow direction), but at high DRs, it fibrillated due to the higher non‐isothermal elongational flow induced by drawing. The laminar structure of the nanoclay allowed the films to be reinforced both in the machine and the transverse directions. The oxygen permeability of PC was reduced by 42% in the nanocomposite with 25% of naPA, and dropped further with the DR, which is attributed to the increased tortuosity of the oxygen path induced by fibrillation. Copyright © 2015 John Wiley & Sons, Ltd.     

The effect of nanoparticle shape on polymer‐nanocomposite rheology and tensile strength

Nanoparticles can influence the properties of polymer materials by a variety of mechanisms. With fullerene, carbon nanotube, and clay or graphene sheet nanocomposites in mind, we investigate how particle shape influences the melt shear viscosity η and the tensile strength τ, which we determine via molecular dynamics simulations. Our simulations of compact (icosahedral), tube or rod‐like, and sheet‐like model nanoparticles, all at a volume fraction ? ≈ 0.05, indicate an order of magnitude increase in the viscosity η relative to the pure melt. This finding evidently can not be explained by continuum hydrodynamics and we provide evidence that the η increase in our model nanocomposites has its origin in chain bridging between the nanoparticles. We find that this increase is the largest for the rod‐like nanoparticles and least for the sheet‐like nanoparticles. Curiously, the enhancements of η and τ exhibit opposite trends with increasing chain length N and with particle shape anisotropy. Evidently, the concept of bridging chains alone cannot account for the increase in τ and we suggest that the deformability or flexibility of the sheet nanoparticles contributes to nanocomposite strength and toughness by reducing the relative value of the Poisson ratio of the composite. The molecular dynamics simulations in the present work focus on the reference case where the modification of the melt structure associated with glass‐formation and entanglement interactions should not be an issue. Since many applications require good particle dispersion, we also focus on the case where the polymer‐particle interactions favor nanoparticle dispersion. Our simulations point to a substantial contribution of nanoparticle shape to both mechanical and processing properties of polymer nanocomposites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1882–1897, 2007