Electrical properties of sulfonated polyether ether ketone/polyetherimide blend membranes doped with inorganic acids

The influence of blending with polyetherimide (PEI) and doping with HCl and H₃PO₄ on the properties of sulfonated polyether ether ketone (SPEEK) was studied. Blending with PEI first results in an increase and then in a decrease in membrane swelling at PEI concentrations greater than 5%. The electrical conductivity of blend membranes follows the same trend. Doping with the acids enhances the conductivity several times, and the effect of doping with HCl is more significant. PEI forms spherical particles dispersed in the SPEEK matrix and, at the same time, partially dissolves in SPEEK, which reduces the swelling of the matrix at higher PEI concentrations. The increase in the membrane capacity to absorb water at small PEI contents is due to the formation of new water adsorption sites along the interface between the particles and the matrix. A modified effective medium model yielded calculated results in good agreement with the measured conductivity values, when the experimental absorption data were used in the simulation. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1386–1395, 2000     

Immobilization of Bovine Serum Albumin on Poly(ether ether ketone)for Surface Biocompatibility Improvement

UV-induced graft polymerization of acrylic acid(AA)on poly(ether ether ketone)(PEEK)films was carried out to introduce-COOH for the subsequent immobilization of bovine serum albumin(BSA).BSA was introd...     

Synthesis of a random copolymer and its compatibility for thermotropic liquid crystalline polymer/poly(ether ether ketone) blends

A random copolymer (RCP) containing poly(ether ether ketone) (PEEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. Its chemical structure and liquid crystalline properties were characterized by FT‐IR, differential scanning calorimetry (DSC) and polar light microscopy (PLM) respectively. A single glass transition temperature (T_g) at 134.0°C, a melting temperature (T_m) at 282.0°C and a temperature of ignition (T_i) at 331.3°C can be observed. Blends of PEEK and TLCP with and without RCP as compatibilizer were prepared by extrusion and the effect of RCP on the thermal properties, dynamic mechanical properties, morphology and static tensile mechanical properties of blends was investigated by means of DSC, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), etc. Dynamic mechanical measurements indicated that there appeared to be only a single tan δ peak resulting from the glass transition of the PEEK‐rich phase and the T_g value shifted towards higher temperature due to the presence of compatibilizer, as suggested partial compatibility. Morphological investigations showed that the addition of RCP to binary blends reduced the dispersed phase size and improved the interfacial adhesion between the two phases. The ternary compatibilized blends showed enhanced tensile modulus compared to their binary blends without RCP. The strain at break decreased for the ternary blends due to embrittlement of the matrix by the incorporation of some RCP to the matrix phase. Copyright © 2007 John Wiley & Sons, Ltd.     

Effect of shear on the crystallization of the poly(ether ether ketone)

The effect of shear on the crystallization behavior of the poly(ether ether ketone) (PEEK) has been investigated by means of ex situ wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering, and differential scanning calorimetry (DSC). The changes of the intensity of WAXD patterns along shear direction of the PEEK induced by short‐term shear were observed when the samples crystallized at 330 °C. The results showed that the dimensions of the crystallites perpendicular to the (110) and (111) planes reduced with the increase of shear rate, whereas the dimensions of the crystallites perpendicular to (200) plane increased with the increase of shear rate. Moreover, increasing shear rate can lead to the increase of the crystallinity as well as the average thickness of the crystalline layers. Correspondingly, a new melting peak at higher temperature was found during the subsequent DSC scanning when the shear rate was increased to 30 s^?1. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 220–225, 2010     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

Effect of Antioxidants on the Stability of Poly(ether ether ketone) and the Investigation on the Effect Mechanism of the Antioxidants to Poly(ether ether ketone)

Two types of antioxidants (a phenolic antioxidant and a phosphorous antioxidant) were used to improve the stability of poly (ether ether ketone) (PEEK). To evaluate the effect of the antioxidants on the properties of PEEK and the stabilization mechanism, some characterization methods were carried out, such as rheometer, TGA, and electron spin resonance (ESR). The results indicated that the efficiency of the phosphorous antioxidant (DS) in improving the stability of PEEK was better than that of the phenolic antioxidant (DN) and the thermal stability of PEEK sample containing 0.07 wt% DS was the best among all samples due to the decrease of the free radicals density, as proven by ESR measurement. The possible stabilization mechanism of the antioxidants to PEEK was proposed to reveal the reason that caused the different performances of the two types of antioxidants to PEEK.     

Covalent attachment of polymeric monolith to polyether ether ketone (PEEK) tubing

A new method of reproducible preparation of vinylic polymeric monolithic columns with a key step of covalently anchoring the monolith to PEEK surface is described. In order to chemically attach the polymer monolith to the tube wall, methacrylate functional groups were introduced onto PEEK surface by a three-step procedure, including surface etching, surface reduction and surface methacryloylation. The chemical state of the modified tubing surface was characterized by attenuated total reflectance infrared (ATR-IR) spectroscopy. It was found that the etching step is the key to successfully modifying the PEEK tubing surface. Poly(styrene-co-divinylbenzene) monoliths were in situ synthesized by thermally initiated free radical copolymerization within the confines of surface-vinylized PEEK tubings of dimensions close to ones conventionally used in HPLC and UHPLC (1.6 mm internal diameter, 10.0–12.5 cm length). Adhesion test was done by measuring the operating pressure drop, which the prepared stationary phases can withstand. Good pressure resistance, up to 140 bar/10 cm (flow rate 0.5 mL min⁻¹, acetonitrile as a mobile phase), indicates strong bonding of monolith to the tubing wall. The monolithic material was proven to have a permeability of 1.7 × 10 ⁻¹⁴ m², applying acetonitrile–water 70:30 (v/v) as a mobile phase.     

Effect of reactive oxygen species generated with ultraviolet lamp and plasma on polyimide surface modification

Understanding the effect of reactive oxygen species (ROS), such as singlet oxygen molecule and atomic oxygen, on polyimide (PI) film properties, such as wettability, morphology, and chemical bonding state, is essential for further development of PI‐based surfaces. We investigated the effect of different ROS generated during ultraviolet (UV) and plasma treatment in oxygen gas on surface modification of Kapton PI. Different surface modification techniques, UV and plasma treatment, are known to generate different ROS. In this work, we demonstrate the effect of different ROS on PI surface modification. From the diagnostics of ROS by means of electron spin resonance and optical emission spectroscopy, we confirmed that during UV treatment, excited singlet oxygen molecules are the main ROS, while plasma treatment mainly generated atomic oxygen. The wettability of PI surface treated by UV and plasma resulted in hydrophilic PI surfaces. XPS results show that the wettability of PI samples is mainly determined by their surface O/C ratio. However, chemical bonding states were different: while UV treatment tended to generate C=O bonds, while plasma treatment tended to generate both C―O and C=O bonds. Singlet oxygen molecules are concluded to be the main oxidant during UV treatment, and their main reaction with PI was concluded to be of the addition type, leading to an increase of C=O groups on the surface of PI film. Meanwhile, atomic oxygen species were the main oxidant during plasma treatment, reacting with the PI surface through both etching and addition reaction, resulting in a wider variety of bonds, including both C―O and C=O groups.     

Direct ESR detection and spin trapping of radicals generated by reaction of oxygen radicals with sulfonated poly(ether ether ketone) (SPEEK) membranes

The stability of membranes under the strong oxidizing conditions in fuel cells is one of the major challenges in the development of fuel cells based on proton exchange membranes (PEMs). This study is centered on the determination of the susceptibility to degradation of SPEEK membranes exposed to OH radicals, using both direct ESR and spin trapping with 5,5-dimethyl-1-pyrroline-1-oxide (DMPO). In order to achieve a complete picture on SPEEK degradation, two types of experiments were performed: 1. UV irradiation at 77 K of SPEEK membranes swollen by aqueous solutions of H₂O₂; 2. UV irradiation of SPEEK membranes swollen by aqueous solutions of H₂O₂ in the presence of DMPO as a spin trap. UV irradiation without oxygen of SPEEK at 77 K in acid or basic form in the presence of H₂O₂/H₂O produced phenoxyl radicals as the predominant radicals detected by direct ESR or spin trapping methods. At pH 4, the oxygen radicals produced phenyl radicals as the predominant species detected by spin trapping methods. The hydroperoxyl radical, as DMPO/OOH adduct, was detected only when the DMPO/OH adduct was absent. The appearance of phenyl and phenoxyl radicals provides the evidence that OH radicals react with the aromatic ring of SPEEK or leading to the scission of its ether bridge.     

Solid‐state bonding of silicone elastomer to glass by vacuum oxygen plasma,atmospheric plasma,and vacuum ultraviolet light treatment

We experimentally demonstrated that treating a silicone elastomer by a vacuum oxygen plasma, an atmospheric pressure plasma, and vacuum ultraviolet (VUV) radiation resulted in different surface modifications that gave different contact angles, contact angle aging, and bond strengths. The aim of this study was to assess whether high‐throughput surface modification techniques of atmospheric pressure plasma and VUV radiation have the potential to replace conventional oxygen plasma modification. Four silicone elastomers with different hardnesses were used as specimens. The surfaces of all four silicone elastomers were successfully modified from hydrophobic to hydrophilic and they were also bonded to glass surfaces by the three surface modification techniques, although considerable variations were observed in the surface hydrophobicity and the bonding properties. The results clearly reveal that atmospheric pressure plasma and VUV treatment have the potential to replace conventional oxygen plasma treatment. In particular, VUV irradiation produced the most hydrophilic surface that was preserved for a long time. Thus, VUV irradiation is the most promising technique for realizing high‐throughput surface modification and bonding of silicone elastomers. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis and properties of aromatic poly (ether sulfone)s and poly (ether ketone)s based on methyl-substituted biphenyl-4,4′-diols

Novel methyl-substituted aromatic poly (ether sulfone)s and poly (ether ketone)s were synthesized from combinations of 3,3′,5,5′-tetramethylbipheny-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol, and 4,4′-dichlorodiphenyl sulfone and 4,4′-difluorobenzo-phenone by nucleophilic aromatic substitution polycondensation. The polycondensations proceeded quantitatively in a N-methyl-2-pyrrolidone-toluene solvent system in the presence of anhydrous potassium carbonate to afford the polymers with inherent viscosities between 0.86 and 1.55 dL/g. The methyl-substituted poly (ether sulfone)s and poly (ether ketone)s showed good solubility in common organic solvents such as chloroform, tetrahydrofuran, pyridine, m-cresol, and N,N-dimethylacetamide. The tetramethyl- and hexamethyl-substituted aromatic polyethers had higher glass transition temperatures than the corresponding unsubstituted polymers, and did not decompose below 350°C in both air and nitrogen atmospheres. The films of the methyl-substituted poly (ether ketone)s became insoluble in chloroform by the irradiation of ultraviolet light, indicating the occurrence of photochemical crosslinking reactions. © 1994 John Wiley & Sons, Inc.     

Surface modification of PVC endotracheal tubes by oxygen glow discharge to reduce bacterial adhesion

A d.c. oxygen glow discharge was used to modify medical‐grade poly(vinyl chloride) (PVC) to study how surface chemistry and hydrophilicity influence Pseudomonas aeruginosa adhesion. The effects of plasma exposure time on the resulting surface, including chemical composition, wettability and roughness, were assessed using x‐ray photoelectron spectroscopy, contact angle measurements and atomic force microscopy analysis. A significant alteration in the hydrophilicity of the native PVC surface was observed after oxygen glow discharge treatment. The water contact angle decreased from ～80° to 8–20°, with a weak dependence of the exposure time used. The change in surface wettability resulted from the incorporation of oxygenated functional groups, including esters, ketones and acids, as indicated by XPS analysis. The amount of oxygen incorporation was shown to be essentially independent of plasma exposure time. However, prolonged plasma exposure resulted in increased surface roughness. Bacterial adhesion efficiency was evaluated for PVC modified by 120 s of plasma exposure, because this exposure time was determined to yield the maximum decrease in contact angle. Oxygen plasma treatment of native PVC was found to yield a 70% reduction in bacterial adhesion for the four strains of Pseudomonas aeruginosa tested. Copyright © 2003 John Wiley & Sons, Ltd.     

The effect of the addition of talc on tribological properties of aramid fiber‐reinforced polyimide composites under high vacuum,ultraviolet or atomic oxygen environment

The aramid fibers‐reinforced polyimide composites filled with talc were fabricated by means of a hot press molding technique, and mechanical and tribological behaviors were comparatively investigated. Experimental results showed that the elastic modulus of the composites increased with an increase of the talc, but the impact intensity and loss factor decreased. Besides, the coefficient of friction decreased with the increase of the talc content. To contrast the effects of the ultrahigh vacuum (VC), ultraviolet (UV) or atomic oxygen (AO) on the composites, experiments without irradiation or after UV or AO irradiation were conducted. Scanning electron microscopy and X‐ray photoelectron spectroscopy (XPS) analysis showed that UV or AO irradiation can change the surface structure and chemical composition of the polymer because of the photooxidation and chemical erosion. Copyright © 2012 John Wiley & Sons, Ltd.     

Miscibility of polyimide with polymeric primer and its influence on adhesion of polyimide to the primed copper metal: Effect of precursor origin

Poly(amic acid) (PAA) and poly(amic diethyl ester) (PAE) precursors of poly(4,4′-oxydiphenylene biphenyltetracarboximide) (BPDA-ODA PI) were synthesized. Miscibility behaviors of these precursors with poly(arylene ether benzimidazole) (PAEBI), which is a good adhesion primer for copper metal, were investigated in N-methyl-2-pyrrolidone (NMP) as well as the condensed state and the imidized state. For the PAA/PAEBI blend over the whole range of compositions, no cloud point was measured either in the NMP solution, the condensed state, or the imidized state. Furthermore, no aggregation of PI chains in the blend films was detected by X-ray diffraction. These results indicate that the PAA and PAEBI are completely miscible at the molecular level, consequently leading to the miscible PI/PAEBI blend. This miscibility might result from the strong interaction via the complex formation of imidazole groups of the PAEBI and carboxylic acid groups of the PAA precursor. In contrast, the miscibility of PAE/PAEBI blend in NMP was limited up to a concentration of 13.5–36.3 wt %, leading to a phase separation in the soft-baked and imidized blend. The blend films rich with one component were optically transparent, which might be due to the phase-separated domains much smaller than 1 μm. The immiscibility might result from the relatively weak interactions of imidazole groups of PAEBI with both the ester and amide linkages in the PAE precursor. The difference in the miscibilities of PAEBI with the PAA and PAE precursors was reflected in the adhesion of PI/PAEBI/copper joints: higher miscibility gave higher adhesion strength. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2806–2814, 1999