Latex film formation studied with the atomic force microscope: Influence of aging and annealing

The surface structure of latex dispersion films was examined with an atomic force microscope. All measurements were done in air on latex films having a minimum film formation temperature of 12°C and a glass transition temperature of 18°C. One aim of this study was to follow structural changes during film formation. Three minutes after spreading the film, its surface layer dried. Afterwards, the structure of the film did not change anymore. Only after 4 months could structural changes be observed: Though individual latex particles could be identified, the particles partly melted into one another.After annealing films at 50° or 60°C for 4 h, the latex particles partly melted into one another, but individual particles could still be identified. When annealing at or above 80°C, no individual latex particles were visible anymore. With increasing temperature the film roughness decreased from 3 nm without annealing to 0.8 nm at 100°C annealing temperature. In addition, islands of 2–4 nm thickness appeared on the film surface. These islands could be scraped off the film by increasing the force between tip and sample, indicating that they are composed of surfactant which was squeezed out of the film.     

Label-free detection of the aptamer binding on protein patterns using Kelvin probe force microscopy (KPFM)

Anti-lysozyme aptamers are found to preferentially bind to the edge of a tightly packed lysozyme pattern. Such edge-binding is due to the better accessibility and flexibility of the edge lysozyme molecules. Kelvin probe force microscopy (KPFM) was used to study the aptamer–lysozyme binding. Our results show that KPFM is capable of detecting the aptamer–protein binding down to the 30 nm scale. The surface potential of the aptamer–lysozyme complex is approximately 12 mV lower than that of the lysozyme. The surface potential images of the aptamer-bound lysozyme patterns have the characteristic shoulder steps around the pattern edge, which is much wider than that of a clean lysozyme pattern. These results demonstrate the potentials of KPFM as a label-free method for the detection of protein–DNA interactions. Figure Aptamers preferentially bind on the edge of a protein pattern as revealed by Kelvin force microscopy.

Influence of attractive force on imaging micro‐droplets of water by atomic force microscope

The shape of micro‐droplets of water on a pure copper surface was investigated using the a.c. non‐contact mode of an atomic force microscope (AFM) by applying different attractive forces between the cantilever tip and the liquid surface. The forces largely influenced the observed radii of micro‐droplets; the influence can be reduced significantly by reducing the force. The same attractive force between the cantilever tip and the micro‐droplets is necessary when comparing the contact angles of micro‐droplets on different surfaces. Furthermore, the values of the contact angles of the micro‐droplets should be the average of those on at least four sides of the droplets. Copyright © 2005 John Wiley & Sons, Ltd.     

Organization of polyhydroxyalkanoate synthase for in vitro polymerization as revealed by atomic force microscopy

Individual polyhydroxyalkanoate synthase molecules from Ralstonia eutropha (PhaCRe) were directly visualized on highly oriented pyrolytic graphite (HOPG) by atomic force microscopy (AFM). PhaCRe molecule was observed as a spherical particle of 2.9 +/- 0.4 nm in height and 28 +/- 4 nm in width. In vitro polymerization reaction on HOPG was carried out for 5 min by reacting the PhaCRe molecules with (R)-3-hydroxybutyryl-CoA monomers. The reaction product was then observed after the removal of water solution. Several PhaCRe molecules associated with each other to form an assembly, which was attached to a fibrillar structure of ca. 0.2-0.3 nm in height. The fibrillar structure that elongated from the PhaCRe assembly was interpreted as the poly[(R)-3-hydroxybutyrate] polymer chain. High resolution AFM suggested that the PhaCRe assembly was composed of 3-4 subunits of PhaCRe molecules. This was further supported by SDS-PAGE analysis of the cross-linked PhaCRe enzyme. These results suggest that more than two subunits of PhaCRe are necessary for the in vitro polymerization of PHB molecular chains.     

Shear banding in strained semicrystalline polyamide 6 films as revealed by atomic force microscopy: Role of the amorphous phase

Atomic force microscopy (AFM) has been used to visualize the plastic deformation mechanisms that are responsible for the yielding of semicrystalline polymers of low degree of crystallinity (<50%). Indeed, AFM, if operated in suitable conditions, is able to image both the amorphous and the crystalline phases. Polyamide 6 films have been drawn at temperatures T < 160 °C. Postmortem AFM observations show that, at yield, shear bands nucleate and propagate in the amorphous phase. They cross the crystalline lamellae and run over the whole surface of the sample. By crossing the lamellae, they form nanoblocks of uniform size. Neither the size of the nanoblocks nor the angle between the tensile axis and the shear bands can be explained in terms of crystal plasticity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 687–701, 2004     

Real-time enzymatic degradation study of poly[(R)-3-hydroxybutyric acid] copolymer thin film by atomic force microscopy in buffer solution

In situ observation of lamellar crystals during the enzymatic degradation by poly(hydroxybutyrate) (PHB) depolymerase is carried out on the thin films of poly[((R)-3-hydroxybutyric acid)-co-(16 mol-%-(R)-3-hydroxypentanoic acid)] using atomic force microscopy in buffer solution. Erosion of lamellar crystals and formation of splintered morphology along the crystal growth direction are directly observed during the course of the enzymatic degradation process. The changes in lamellar morphologies caused by enzymatic degradation are discussed in terms of lamellar crystal growth process.

AFM images of a P[(R)-3HB-co-(R)-3HV] thin film before and during enzymatic degradation.     

Observation of banded spherulites and lamellar structures by atomic force microscopy

Spherulites are common structures of semi-crystalline polymers. It has been known that semi-crystalline polymers can form spherulites when crystallized from solution or from melt. A dark Maltese cross of a spherulite could be easily observed under the polarized optical microscopy (POM). Moreover, some spherulites show an additional alternating dark and bright concentric ring structure that is attributed to the regular twisting of the radial crystallite ribbons as they grow from the spherulit…     

Adsorption behavior of hexadecyltrimethylammonium bromide (CTAB) to mica substrates as observed by atomic force microscopy

The study of the adsorption behavior of surfac-which makes people further study the adsorptiontants to interfaces is very important in colloid and in-mechanism at the molecular level.terface science[1]owing to the important applications In situ AFM measur…     

Morphological studies of spin-coated films of poly(styrene-block-methyl methacrylate) copolymers by atomic force microscopy

The surface structure of very thin (15–20 nm) spin-coated films of a symmetrical poly(styrene-b-methyl-methacrylate) block copolymer on silicon and mica is analyzed by atomic force microscopy (AFM). The films show a surface corrugation of a very regular 100 nm lateral periodicity and 6–8 nm amplitude. Film thickness is measured by AFM at induced film defects and checked by ellipsometry. XPS shows that both blocks are at the film surface. Selective degradation of the methyl methacrylate block is used for contrast enhancement and allows to assign poly(styrene) to the elevated surface regions and poly(methyl methacrylate) to the substrate/film interface.Friction interactions of the AFM tip with the film surface may be used to induce high orientational ordering of the morphological pattern perpendicular to the fast scan direction.     

Kinetics of latex formation of PBMA latex in the presence of alkali soluble resin using atomic force microscopy

 The effect of alkali-soluble resin (ASR), poly(ethylene-co-acrylic acid), EAA, postadded to emulsifier-free monodisperse poly(butyl methacrylate) (PBMA) latexes on the kinetics of film formation was investigated using atomic force microscopy (AFM). Corrugation height of latex particles in films was monitored at various annealing temperatures as a function of annealing time. Enhanced polymer diffusion was found in a latex film containing ASR regardless of anneal-ing temperature. With increasing annealing temperature, a much higher rate of polymer diffusion was found in latex films containing ASR. These results can be interpreted that the low molecular weight and low Tg EAA resin adsorbed at the particle surface is more susceptible to diffusion than that of the PBMA in the film formation stage, thus it enhances the mobility of PBMA polymer. Received: 30 October 1997 Accepted: 20 March 1998     

Parametric signal fitting by gaussian peak adjustment: A new multivariate curve resolution method for non-bilinear voltammetric measurements

A new methodology based on the fitting of signals to parametric functions is proposed for the multivariate curve resolution (MCR) analysis of overlapping and peak-shaped voltammetric signals which progressively get broader or narrower and move along the potential axis, thus causing a dramatic loss of linearity. The method is based on the least squares fitting of gaussian functions at both sides of the peaks by using adjustable parameters for the peak height, position and symmetry. It consists of several home-made programs written in Matlab environment, which are freely available as supplementary material of the present work. The application to the systems Zn(II)–oxalate, and to the phytochelatin PC₅ in a wide pH range provides excellent results as compared to these of more conventional linear methods, which raises good expectations about future application to electrochemical and even non-electrochemical data.     

Ozonization and cyclic voltammetry as efficient methods for the regeneration of gelatin-coated SPR chips

The application of ozonization and cyclic voltammetry for the regeneration of gold chips containing a chemisorbed gelatin layer is reported. The efficiency of the regeneration process was analyzed using various surface analysis techniques indicating a complete removal of the biopolymer layer. The current findings open up perspectives for regeneration and multiple application of gold chips for SPR measurements.     

Depth Profiling by AFM Nanoindentations and Micro‐FTIR Spectroscopy for the Study of Polymer Ageing

Summary: A method of depth profiling by AFM nanoindentations is developed for the characterisation of the heterogeneity of the mechanical properties of oxidised polymers. An increase or a decrease of the sample stiffness is measured close to the surface. A comparison with micro‐FTIR profiles and a knowledge of the photooxidation mechanism permit an interpretation of the chemical and physical changes and give new insights into the understanding of the ageing behaviour.

Photooxidation profile of a TMPC film measured by AFM (•) and by micro‐FTIR (♦) after irradiation.     

Stretched polymer surfaces: Atomic force microscopy measurement of the surface deformation and surface elastic properties of stretched polyethylene

The surface structure and surface mechanical properties of low‐ and high‐density polyethylene were characterized by atomic force microscopy (AFM) as the polymers were stretched. The surfaces of both materials roughened as they were stretched. The roughening effect is attributed to deformation of nodular structures, related to bulk spherulites, at the surface. The surface‐roughening effect is completely reversible at tensile strains in the elastic regime and partially reversible at tensile strains in the plastic regime until the polymers are irreversibly drawn into fibers. AFM force versus distance interaction curves, used to measure changes in the stiffness of the surface and the surface elastic modulus as a function of elongation, show that the surfaces become softer as the polymers are drawn into fibers at high strains. At low elastic strains, however, the surface elastic modulus of HDPE increases—attributed to elastic energy stored by the amorphous regions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2263–2274, 2001     

A method for determination of dimethyl benzoylphenyl urea (BPU) in human plasma by using LC/UV

Dimethyl benzoylphenyl urea (BPU) inhibited tubulin polymerization, caused microtubule depolymerization in vitro and demonstrated activity against solid tumors. BPU is being tested in phase I clinical trials. A rapid and specific method using LC/UV has been developed for quantitation of BPU in human heparin-containing plasma to perform pharmacokinetic and pharmacodynamic studies. BPU is extracted from plasma into acetonitrile:n-butyl-chloride using paclitaxel as the internal standard and separated on a Waters Symmetry C18 (3.9 x 150 mm, 5 microm) column with acetonitrile-water mobile phase (70:30, v/v) using isocratic flow at 1 mL/min for a run time of 5 min. Ultraviolet detection was utilized and performed at 225 nm for BPU and paclitaxel. The retention times were 1.9 min for paclitaxel and 4.1 min for BPU. Calibration curves were generated over the range of 0.01-10 microg/mL with coefficient of determination of > 0.99. The values for within-day and between-day precision were < or = 17.0% at the LLOQ and < or = 7.4% at the low, medium and high quality controls; accuracy was +/- 5.4%. Following administration of BPU 320 mg as a weekly oral dose to a patient with advanced solid tumor malignancies, the maximum plasma concentration was 2 micro g/mL and concentrations were quantifiable up to 168 h after administration. The lower limit of quantitation of 0.01 microg/mL allows for successful measurement of plasma concentrations in patients.     

Morphology of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) assemblies in diluted aqueous solution and gel studied by atomic force microscopy

Morphologies of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) (PCL‐PEG‐PCL) triblock copolymer self‐assemblies in the diluted solution and in gel were studied by atomic force microscopy (AFM). The copolymer self‐assembled into wormlike aggregates, of uniform diameter, in water. The wormlike aggregates arranged in order to form separate clusters in the diluted copolymer solution; at a higher copolymer concentration, the clusters became bigger and bigger, and packed together to form gel. Copyright © 2008 John Wiley & Sons, Ltd.     

Tensile versus AFM testing of electrospun PVA nanofibers: Bridging the gap from Microscale to nanoscale

Design and application of mechanically extraordinary nanofibers requires their full comprehension, based on conclusive testing methods. Electrospun polymer nanofibers, for instance, show a progressive and pronounced increase in their Young's moduli when diameters decrease below the µm scale. Measurement of mechanical properties in this diameter range is challenging and in the vast majority of reports, two classes of methods are commonly used: highly sensitive tensile testing and atomic force microscopy three‐point deformation testing. Despite the methods' inherent dissimilarity, we resolve their conformity for the first time, with respect to the determination of Young's moduli. Here, we benchmark them against each other for electrospun polyvinyl‐alcohol nanofibers, a well‐defined model system. Our results provide an experimental basis for a comprehensive understanding of nanofiber structures and its implications on their mechanical properties. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2418–2424     

Substrates for flexible electronics: A practical investigation on the electrical,film flexibility,optical, temperature,and solvent resistance properties

Designing and developing flexible electronics requires a thorough investigation of the substrates available for the fabrication of devices. Here, we present a practical study on a variety of significant substrates: polyethylene terephthalate (PET), its heat‐stabilized (HS) derivative, HS‐PET, and polyethylene naphthalate (PEN) plastic insulating films; indium tin oxide (ITO)‐coated ITO/PEN and ITO/PET transparent conducting films; rigid ITO/glass and FTO/glass substrates; stainless steel and titanium foils. We put the substrates through a range of tests these actually undergo during device fabrication to determine their optical, mechanical flexibility (under different types of tensile and compressive stress bending with and without a PEDOT:PSS conducting polymer layer), solvent resistance, stability to temperature treatment (conductivity and deformation), and to UV irradiation. We highlight issues and propose solutions to improve substrate response. The results and thresholds extracted reveal limitations and windows of opportunity useful for the designer of flexible optoelectronics in determining manufacturing processes and the final applications under everyday operation. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Synthesis and property of helical poly(phenylacetylene)s bearing chiral ruthenium complexes and real space imaging of meso- and nanoscopic structures by atomic force microscopy

Novel sets of helical poly(phenylacetylene)s bearing a chiral ruthenium (Ru) complex with opposite chirality (Δ and Λ forms) as a bulky pendant (poly- 1 and poly- 2 ) were synthesized through the polymerization of the corresponding optically pure phenylacetylenes with a rhodium catalyst, and their structures in solution and morphology on solid substrates were investigated with NMR, ultraviolet–visible, and circular dichroism (CD) spectroscopies and with atomic force microscopy (AFM), respectively. The obtained cis–transoidal polymers (poly- 1 and poly- 2 ) showed characteristic Cotton effects in the region of metal-to-ligand charge transfer of the chiral Ru pendants. Poly- 1 and poly- 2 were thought to have a predominantly one-handed helical conformation induced by the chiral pendants. However, the apparent Cotton effects derived from the helically twisted π-conjugated polymer backbone could not be observed, probably because of the strong chiral chromophoric pendants. However, in the AFM images, the helical polymers adsorbed on mica could be easily discerned as isolated strands, and the visualization and discrimination of the right- and left-handed helical structures of the chiral polymers were achieved by high-resolution AFM imaging. On the basis of the AFM observations together with the CD measurements and computational calculation results, possible structures of poly- 1 and poly- 2 were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4621–4640, 2004     

A Novel Electrochemical Sensor Based on Modified Carbon Paste Electrode with ZnO Nanorods for the Voltammetric Determination of Indole-3-acetic Acid in Plant Seed Extracts

Detection of indole-3-acetic acid (IAA), as a phytohormone, is important for precision farming, plant phenotyping, and crop management. Herein, IAA was detected in bean and wheat plant seeds extractions using zinc oxide nanorods/carbon paste electrode (ZnO NRs/CPE). ZnO NRs/CPE showed excellent electrocatalytic activity, high sensitivity, and selectivity toward the oxidation of IAA. The linearity range was from 30.×10⁻⁸ to 5.0×10⁻⁶ M (r²=0.996, n=10), with a detection limit of 1.7×10⁻⁸ M. Moreover, ZnO NRs/CPE exhibited high reproducibility, with a standard deviation of 1.0 % for six successive measurements of IAA.