聚邻苯二胺/铂复合电极的制备及其电催化研究

利用原位聚合原位还原复合法制备了聚邻苯二胺(PoPD)/铂(Pt)复合电极。通过扫描电镜(SEM)、x射线能谱(XRD)、傅立叶变换红外光谱(FTIR)、和交流阻抗(EIS)对其形貌、组成元素和结构等进行了表征。研究了Poly(O-Phenylenediamine)/Platinum电极对甲醇的电催化行为,发现该复合电极对甲醇有良好的电催化性能。与裸铂电极相比,氧化电流高出约4.5倍。通过循环伏安法和计时电量法测定了修饰电极在甲醇溶液中的动力学参数,测得电子转移数为1,扩散系数为8.5687×10-7㎝2/s。     

二氧化锰纳米层的制备及电容性能研究

以Mn(NO3)2、Na OH和H2O2为原料,采用水热技术制备了Na型层状氧化锰(Na-Mn O2)。通过离子交换反应对NaMn O2进行了剥离,得到了氧化锰纳米层胶体分散液。将氧化锰纳米层分散液冷冻干燥后得到了氧化锰重组物(ERMn O2)。通过XRD、SEM和AFM对制备试样进行了分析表征。电化学测试结果表明,在1.0 mol·L-1Na2SO4水溶液中,当电流密度为0.25 A·g-1时,ERMn O2的质量比电容高达117 F·g-1远远高于其前驱物Na-Mn O2的比电容(79 F·g-1),并且表现出相似的循环稳定性。     

Standard enthalpy of formation of platinum hydrous oxide

Standard enthalpies of formation of amorphous platinum hydrous oxide PtH_2.76O_3.89 (Adams' catalyst) and dehydrated oxide PtO_2.52 at T=298.15 K were determined to be -519.6±1.0 and -101.3 ±5.2 kJ mol^-1, respectively, by micro-combustion calorimetry. Standard enthalpy of formation of anhydrous PtO₂ was estimated to be -80 kJ mol^-1 based on the calorimetry. A meaningful linear relationship was found between the pseudo-atomization enthalpies of platinum oxides and the coordination number of oxygen surrounding platinum. This relationship indicates that the Pt-O bond dissociation energy is 246 kJ mol^-1 at T=298.15 K which is surprisingly independent of both the coordination number and the valence of platinum atom. This may provide an energetic reason why platinum hydrous oxide is non-stoichiometric. This revised version was published online in August 2006 with corrections to the Cover Date.     

透光导电金属及氧化铂半导体薄膜的制备与表征

通过PPh~3对“非保护型”铂金属纳米簇进行表面修饰,并将其萃取至甲苯中,制备的PPh~3修饰的Pt金属钠米簇于空气中可自发地在玻璃表面生长出均匀透光的金属钠米簇薄膜。该金属钠米簇薄膜经空气中加热处理后可转化为透光导电的氧化铂半导体薄膜。考察了金属钠米簇薄膜生长过程中UV-vis吸收光谱的变化。采用SEM和TEM等方法,表征了纳米簇的粒径及膜的多孔结构,由此解释了其透光原因。研究了薄膜的导电性与处理条件的关系,并采用XPS表征了处理过程中的物质变化。初步探索了PPh~3-Pt纳米簇自发成膜过程的机理,确定了氧气在此过程中的重要作用。     

pH-dependent assembly of two polyoxometalate-based coordination polymers: structures and electrocatalytic properties

Two new polyoxometalate-based coordination polymers have been synthesized at different pHs under identical hydrothermal conditions, (Hbib)[Cu₂(bib)₂(PMo₁₂O₄₀)] (1) and (Hbib)₂[Cu(bib) (PMo₁₂O₄₀)]·2H₂O (2) (bib = 4-bis(imidazol-1-yl) benzene). Their structures were determined by single crystal X-ray diffraction analyses and characterized by routine methods. When the pH was adjusted to 2.0???2.5, 1 was obtained, which exhibits a 1-D rail-like chain. Compound 2 was obtained at pH of 2.5???3.2 and exhibits a 2-D layer with (4⁴) sql net. The pH of the reaction plays a key role in the assembly of the polyoxometalate-based coordination polymer. The electrochemical experiments indicate that 2-based carbon paste electrode possesses high catalytic efficiency and high stability towards reduction of iodate and oxidation of ascorbic acid.     

Preparation of different thin film catalysts by direct current magnetron sputtering for hydrogen generation

In this study, thin films of Co, Ni, Pd, and Pt were prepared on Co ₃ O ₄ support material in pellet form using the direct current (DC) magnetron sputtering method for use as catalysts for hydrogen generation from NaBH ₄ .Characterization of the catalysts was carried out using X-ray diffraction (XRD), scanning electronic microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). According to cross-sectional SEM images, catalyst thicknesses were observed in the range of approximately 115.3–495.8 nm. The particle sizes were approximately 25.0, 21.4, 33.9, and 9.5 nm for Ni-Co ₃ O ₄ , Co-Co ₃ O ₄ , Pd-Co ₃ O ₄ , and Pt-Co ₃ O ₄ catalysts, respectively. The increase in NaOH initial concentration provides an increase in the rate of hydrogen generation for Co, Ni, and Pd catalysts. A maximum hydrogen generation rate of 1653 mL/g _cat .min was obtained for the Pt-Co ₃ O ₄ catalyst.     

咪唑四氟硼酸盐离子液体中磷钼酸掺杂聚吡咯薄膜修饰电极的制备及其电催化活性

以1-丁基-3-甲基咪唑四氟硼酸盐(BMIMBF4)离子液体作为介质,利用电化学方法在铂电极表面制备了磷钼酸掺杂聚吡咯薄膜;采用扫描电子显微镜观察了所制备的薄膜的形貌,利用热重分析评价了其热稳定性,利用循环伏安法测定了其电化学活性和对甲醇的电催化氧化活性.结果表明,与传统的硫酸溶液相比,以BMI-MBF4离子液体作为反应介质制备的修饰电极的表面形貌更均匀,电化学活性和对甲醇的电催化氧化活性更强.     

磁控溅射制备的铜钒氧化物薄膜及其电化学性能

采用射频磁控溅射技术在硅基底上分别制备了无掺杂和掺杂Cu的氧化钒薄膜. X射线衍射(XRD)分析和扫描电子显微镜(SEM)观察表明, 无掺杂的薄膜为多晶V2O5, 掺杂Cu的薄膜为非晶态. X射线光电子能谱(XPS)分析结果表明, 掺杂Cu的薄膜为铜钒氧化物膜, 其中Cu离子表现为+2价, V离子为+4与+5价的混合价态. 随着Cu掺杂量的增大, +4价V的含量增加. 电化学测试结果表明, V2O5薄膜在掺杂Cu以后其放电容量有显著的提高, 其中Cu2.1VO4.4薄膜在100次循环后容量还保持为83.4 μA·h·cm-2·μm-1, 表现出较高的放电容量和较好的循环性能.     

Effect of platinum on the photoelectrochemical behavior of lead oxide thin film

The effect of Pt on the photoelectrochemical behavior of lead oxide prepared from anodization of Pb-Pt alloy containing various concentrations of Pt has been studied. It is observed that, while Pt reduces the resistivity of the oxide film, it also reduces the photoconversion efficiency of the photoelectrochemical cell prepared from this material. The reason for this low efficiency is discussed. Received: 19 November 1997 / Accepted: 9 March 1998     

氢氧化镍薄膜修饰玻碳电极的制备及其对L-赖氨酸氧化的电催化活性

采用恒电位沉积方法将氢氧化镍沉积到玻碳电极表面,得到稳定性高、催化活性好的氢氧化镍薄膜修饰玻碳电极;分析了影响薄膜形成过程的关键因素,确定了最佳薄膜制备方案;与此同时,将薄膜修饰玻碳电极用于生物样品L-赖氨酸的氧化测定,并探讨了其催化作用机理.结果表明,所制备的氢氧化镍薄膜修饰玻碳电极表面发生电化学反应[Ni(OH)2→NiOOH],从而促进电极表面的电子转移,实现对L-赖氨酸的电催化作用.当L-赖氨酸的浓度在1.0×10-4～4.0×10-7 mol/L范围内时,相应氧化峰电流与浓度呈线性关系,检出限达4.0×10-7 mol/L;据此可方便地制备稳定性好且灵敏度高的电流型传感器.     

溅射功率对氧化锡薄膜结构和电化学性能的影响

应用射频磁控溅射技术在硅基底上制备氧化锡薄膜,着重研究溅射功率对薄膜结构和电化学性能的影响.XRD,SEM分析及恒电流充放电测试表明,随着溅射功率的增大,薄膜的结晶程度提高;生长速率和晶粒尺寸增大;电池的贮锂容量减少,且首圈不可逆容量损失增大.溅射功率对薄膜的电化学性能有较大的影响.     

Function of triazenido compound for electrocatalytic hydrogen production catalyzed by platinum complex

A new type of electrocatalyst based on a triazenido-platinum complex, Pt(PPh₃)₂(L)Cl (1), is prepared by the reaction of 1-[(2-methoxy) benzene]-3-[2-pyridine] triazene (HL) and Pt(PPh₃)₂Cl₂ in the presence of triethylamine. Electrochemical studies indicate that HL, Pt(PPh₃)₂Cl₂ and 1 can catalyze hydrogen evolution from acetic acid or a neutral buffer. To show triazenido ligand, HL, plays a role in determining the catalytic activities of the platinum complex, we systematically study the electrocatalytic activities of HL, Pt(PPh₃)₂Cl₂ and Pt(PPh₃)₂(L)Cl and provide a possible catalytic mechanism for hydrogen generation catalyzed by 1.     

Two-dimensional copper oxide/zinc oxide nanoflakes with three-dimensional flower-like heterostructure enhanced with electrocatalytic activity toward nimesulide detection

The strategy of building two-dimensional (2D) metal oxide nanoflakes has inspired several innovations in different fields of application on account of its tremendous significance. It includes ultrathin planar surface, large charge carrier mobility, and tunable band structures, providing unprecedented features for sensing. Moreover, the intercalation of 2D dimensions to 3D superstructures will result in improved and dual advantages of both 2D/3D. The construction of 2D/3D copper oxide zinc oxide nanocomposite as electrode material for specific detection of nimesulide (NMS) is herein reported. The conversion of 2D CZ nanoflakes to 3D CZ microflowers was possibly achieved via the self-assembly process. This simple and cost-effective development of the CZ composite was characterized for evaluating the physical, chemical, and morphological properties. The highly crystalline nature of CZ was observed from powder X-ray diffraction and X-ray photoelectron spectroscopy analysis. The formation of 2D nanoflakes of CZ was strongly confirmed from field emission scanning electron microscopy and high-resolution transmission electron microscopy images. To verify the strong attachments, Fourier transforms infrared spectroscopy spectra were analyzed. Electrochemical sensing of NMS at CZ fabricated glassy carbon electrode reflects higher electrocatalytic activity with a linear range of NMS addition from 0.299 μM to 319.15 μM. The lower detection limit was about 0.005 μM with a sensitivity of 7.152 μAμM^?1 cm². The CZ nanocomposite will be more applicable for sensing several drugs with enriched active sites, higher conductivity, and large surface area raised from low-cost metal oxides when compared with highly conducting materials.     

Pt/三苯胺烯分子纳米复合物的制备及光催化作用

采用乙醇还原法制备了金属Pt/三苯胺烯共轭分子纳米复合物(Pt@DPSDA),通过UV-vis、TEM、FTIR、XRD、荧光、光电化学等方法对纳米复合物进行了表征.三苯胺烯分子通过分子末端羧基与金属Pt纳米粒子表面原子相互作用,形成以金属Pt纳米粒子为核,三苯胺烯分子为壳的核/壳型纳米复合物.光照下纳米复合物中激发态有机分子与金属Pt纳米粒子之间具有较好的电子转移作用,Pt@DPSDA纳米复合物可以作为催化剂在紫外-可见光照下分解水获得氢气.     

Electrodeposition and electrocatalytic properties of platinum nanoparticles on multi-walled carbon nanotubes: effect of the deposition conditions

Platinum (Pt) nanoparticles were electrochemically deposited on multi-walled carbon nanotubes (MWCNTs) through a three-step process, including an electrochemical treatment of MWCNT, electro-oxidation of PtCl₄ ²⁻ to Pt(IV) complex, and an electro-conversion of Pt(0) on MWCNT. The effect of formation conditions for Pt(IV) complexes on the Pt nanoparticals transformed was investigated. The structure and elemental composition of the resulting Pt/MWCNT electrode were characterized by transmission electron micrograph (TEM) and energy dispersive X-ray spectroscopy (EDX). The electrocatalytic properties of the resulting Pt/MWCNT electrode for methanol oxidation have been investigated. The high electrocatalytic activity and good stability of Pt/MWCNT electrode may be attributed to the high dispersion of platinum nanoparticles and the particular properties of the MWCNT supports.     

氧化钨纳米棒团簇的制备及电催化性能

以氯化钨为前驱体,通过溶剂热法制备了WO₃和W₁₈O₄₉并将其应用在染料敏化太阳能电池(dye-sensitized solar cells,DSSCs)和电解水析氢反应(hydrogen evolution reaction,HER)中。通过X射线衍射仪(XRD)、场发射扫描电子显微镜(FESEM)和透射电子显微镜(TEM)对WO₃和W₁₈O₄₉的结构和形貌进行表征。结果表明：WO₃和W₁₈O₄₉均为单斜相,其形貌表现为定向排列的纳米棒组成的团簇。X射线光电子能谱(XPS)和电子顺磁共振(EPR)表明W₁₈O₄₉中含有丰富的氧空位。基于氧空位优异的电化学特性,W₁₈O₄₉对电极组装的DSSC获得了7.41%的光电能量转换效率(power conversion efficiency,PCE),高于WO     

Oxidation of methanol at the network film of polyoxometallate-linked ruthenium-stabilized platinum nanoparticles

We explore here the ability of ruthenium hydroxo species to undergo spontaneous deposition on Pt nanoparticles and to form colloidal solutions of oxoruthenium-protected (-stabilized) nanoparticles of Pt. These particles can be spontaneously attracted to carbon substrates, and they form ultrathin self-assembled films. Fabrication of the multilayer network films on electrodes has been achieved by linking the positively charged oxoruthenium-covered Pt clusters with heteropolyanions of tungsten. By repeated alternate treatments in a solution of phosphododecatungstate (PW₁₂O₄₀^3–) and in a colloidal suspension of oxoruthenium-protected (-stabilized) Pt nanoparticles, the film thickness can be increased systematically (layer by layer) to form stable three-dimensional assemblies on carbon electrodes. It is apparent from cyclic voltammetric and chronoamperometric measurements (that were performed at 20 and 60 °C) that the resulting hybrid films show attractive properties towards the oxidation of methanol at fairly low potentials (0.25–0.4 V versus the saturated calomel electrode). With approximately the same loading of oxoruthenium-covered Pt nanoparticles and under analogous conditions, linking or derivatizing the nanoparticles with phosphotungstate leads to the systems higher electrocatalytic activity. It is possible that, in addition to ruthenium hydroxo species, PW₁₂O₄₀^3– exhibits an activating effect on dispersed Pt particles. An alternative explanation may involve the possibility of different morphologies of the catalytic films in the presence and absence of phosphotungstate anions.Dedicated to Zbigniew Galus on the occation of his 70th birthday     

PZT铁电薄膜底电极制备工艺的研究

利用磁控溅射方法在Si(001)基片上制备Ti/Pt底电极,其厚度大概分别为20、100 nm,其中Ti电极作为缓冲层,随后在上面溅射PZT铁电薄膜.研究了不同电极的制备工艺对电极形貌、取向以及对PZT铁电薄膜的制备带来的影响.结果表明,底电极的溅射温度以及退火温度对于底电极起着至关重要的作用,同时具有良好(111)取向的、致密性较好的底电极对于PZT铁电薄膜的生长具有重要的影响.     

Preparation of glass carbon electrode modified with nanocrystalline nickel-decorated carbon nanotubes and electrocatalytic oxidation of methanol in alkaline solution

Nanocrystalline nickel with an average diameter of about 16 nm and a face-centered cubic (fcc) structure was uniformly attached to the surface of carbon nanotubes (CNT) by wet chemistry. The sample was characterized by X-ray powder diffraction and transmission electron microscopy (TEM). A glass carbon electrode modified with nickel-modified multi-wall carbon nanotubes (MWCNTs-Ni/GCE) was prepared. The electrochemical behavior of the MWCNTs-Ni/GCE and the electrocatalytic oxidation of methanol at the MWCNTs-Ni/GCE were investigated by cyclic voltammetry in 1.0 mol/L NaOH solution. The cyclic voltammograms showed that the electron transfer between β-Ni(OH)₂ and β-NiOOH is mainly a diffusion-controlled quasireversible process, and that the electrode has high catalytic activity for the electrooxidation of methanol in alkaline medium, revealing its potential application in alkaline rechargeable batteries and fuel cells. __________ Translated from Chinese Journal of Applied Chemistry, 2007, 24(5): 503–506 [译自: 应用化学]