Amphiphilic graft copolymers based on ultrahigh molecular weight poly(styrene-alt-maleic anhydride) with poly(ethylene glycol) side chains for surface modification of polyethersulfone membranes

Amphiphilic graft copolymers having ultrahigh molecular weight poly(styrene-alt-maleic anhydride) (SMA) backbones and methoxyl poly(ethylene glycol) (MPEG) grafts were synthesized via the esterification between anhydride groups with hydroxyl groups. The synthesized graft copolymers, SMA-g-MPEGs, were used as additives in the preparation of polyethersulfone (PES) membranes via phase inversion process. X-ray photoelectron spectroscopy (XPS) analysis showed the comb-like graft copolymers spontaneously segregated to membrane surface during membrane formation. Water contact angle measurements and water absorbance experiments indicated the PES/SMA-g-MPEG blend membranes were much more hydrophilic than pure PES membrane. The blend membranes had stronger protein adsorption resistance than pure PES membrane did. After washed using de-ionized water for 25 days, the blend membranes exhibited higher hydrophilicity and stronger protein adsorption resistance. This phenomenon was attributed to the further accumulation of SMA-g-MPEG additives on membrane surface in aqueous conditions. SMA-g-MPEGs can be well preserved in membrane near-surface and not lost during membrane washing due to their high molecular weight and comb-like architecture.     

Surface modification of polyethersulfone membranes by blending triblock copolymers of methoxyl poly(ethylene glycol)-polyurethane-methoxyl poly(ethylene glycol)

The surface of polyethersulfone (PES) membrane was modified by blending triblock copolymers of methoxyl poly(ethylene glycol)-polyurethane-methoxyl poly(ethylene glycol) (mPEG-PU-mPEG), which were synthesized through solution polymerization with mPEG Mns of 500 and 2000, respectively. The PES and PES/mPEG-PU-mPEG blended membranes were prepared through spin coating coupled with liquid-liquid phase separation. FTIR and (1)H NMR analysis confirmed that the triblock copolymers were successfully synthesized. The functional groups and morphologies of the membranes were studied by ATR-FTIR and SEM, respectively. It was found that the triblock copolymers were blended into PES membranes successfully, and the morphologies of the blended membranes were somewhat different from PES membrane. The water contact angles and platelet adhesion were decreased after blending mPEG-PU-mPEG into PES membranes. Meanwhile, the activated partial thromboplastin time (APTT) for the blended membranes increased. The anti-protein-fouling property and permeation property of the blended membranes improved obviously. SEM observation and 3-(4, 5-Dimethylthiazol-2-yl)-2, 5-diphenyl tetrazolium bromide (MTT) assay proved the surfaces of the blended membranes promoted human hepatocytes adhesion and proliferation better than PES membrane.     

Electrospun microfibrous poly(styrene-alt-maleic anhydride)/poly(styrene-co-maleic anhydride) mats tailored for enzymatic remediation of waters polluted by endocrine disruptors

Novel bicomponent microfibrous mats containing targeted amount of reactive maleic anhydride groups were prepared by electrospinning of mixed solutions of poly(styrene-alt-maleic anhydride) and poly(styrene-co-maleic anhydride). Then, amino-functionalized P(St-alt-MA)/P(St-co-MA) mats were obtained by reaction with p-phenylenediamine. ATR-FTIR and XPS spectroscopy were used to characterize pristine and modified P(St-alt-MA)/P(St-co-MA) mats. On the next step, laccase from Trametes versicolor was covalently attached onto the modified mats; the average amount of immobilized enzyme was 40 ± 0.7 mg/g mat. The catalytic activity of the immobilized enzyme was studied in respect to bisphenol A (BPA) endocrine disruptor. The optimum activity of the immobilized enzyme was reached at maximum flow rate of 1.3 mL/s. After 90 min the BPA concentration was reduced by 60% and the catalytic activity of microfibrous mats remained stable for about 30 successive reuses. In addition, the relative activity of laccase immobilized on the microfibrous mats was displayed in a broader pH range as compared to that of the free one.     

Enhanced desulfurization performance and swelling resistance of asymmetric hydrophilic pervaporation membrane prepared through surface segregation technique

The severe swelling behavior of most hydrophobic membranes has always been an obstinate problem when separating organic mixtures by pervaporation. In some cases, hydrophilic membranes may be an appropriate alternative. In this study, amphiphilic copolymer Pluronic F127 was employed as a surface modifier to fabricate polyethersulfone (PES) asymmetric pervaporation membranes via surface segregation. The scanning electron microscopy (SEM) photographs showed an asymmetric structure of PES/Pluronic F127 membranes. The Fourier transform-infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and static water contact angle measurements confirmed the hydrophilic modification of the membrane surface. Based on the distinct difference of solubility in water between thiophene and n-octane, the prepared membranes were utilized to remove thiophene from n-octane by pervaporation. The effect of Pluronic F127 content on the pervaporation performance was evaluated experimentally. It has been found that both the permeation flux and enrichment factor exhibited a peak value of approximately 60 wt% of the Pluronic F127 content. The highest enrichment factor was around 3.50 with a permeation flux of 3.10 kg/(m² h) for 500 mg/L sulfur in the feed at 30 °C. The influence of various operating parameters on the pervaporation performance was extensively investigated.     

Enhancing the antifouling property of polyethersulfone ultrafiltration membranes through surface adsorption-crosslinking of poly(vinyl alcohol)

An adsorption-crosslinking process of poly(vinyl alcohol) (PVA) was introduced to modify the surface of polyethersulfone (PES) ultrafiltration membranes for enhancement of their antifouling property. XPS and water contact angle measurement confirmed the obvious enhancement of surface hydrophilicity. Ultrafiltration results showed that the spreading of PVA chains over the hydrophobic membrane surface caused substantial but acceptable decrease on membrane flux. The fouling type analysis indicated that PVA adsorption effectively improved the antifouling property of PES membranes. With a PVA concentration of 0.5 wt% and three cycles of alternative adsorption-crosslinking, the total and irreversible fouling ratio of modified membranes were 0.38 and 0.22, respectively, much lower than those of control PES membrane (0.61 and 0.47), and the flux recovery ratio was increased accordingly. The long-term ultrafiltration experiment demonstrated the improvement of recycling property and the reliability of adsorption-crosslinking process.     

支化型交替聚(苯乙烯-alt-马来酸酐)自组装胶束的制备及其乳化性能

利用支化型交替聚(苯乙烯-alt-马来酸酐)(BPSMA)在选择性溶剂DMF-H_2O中自组装制备球形胶束,以该胶束作为新型颗粒乳化剂稳定油-水体系,探讨胶束浓度和pH对BPSMA胶束乳化性能的影响。用紫外分光光度计(UV-Vis)追踪了聚合物溶液自组装过程;粒径及Zeta电位分析仪和透射电子显微镜(TEM)表征了BPSMA胶束的基本性质;利用光学显微镜分析了乳液性质,扫描电子显微镜(SEM)观察了胶束在固化后的油滴表面的形貌。结果表明:BPSMA胶束具有优异的乳化效率,在极低的质量浓度下(0.25~1.00 mg/mL)亦可长期稳定乳液;BPSMA胶束所稳定的乳液具有明显的pH响应性,当pH≤6时,胶束呈球形颗粒状吸附并稳定于油水界面,当pH6时,胶束从油水界面脱离,乳液破乳;此外,BPSMA胶束作为颗粒乳化剂还具备良好的普适性,可以长效稳定碳酸二辛脂、辛酸丙基庚酯、硅油、棕榈酸异辛酯和润肤油脂等。     

Modification of poly(styrene-alt-maleic anhydride) with 1,3,4-oxadiazole units for electroluminescent devices

New copolymers of poly(styrene-alt-maleic anhydride) (PSMA) modified with 2-(4-aminophenyl)-5-(biphenyl-4-yl)-1,3,4-oxadiazole and hexylamine were prepared. The copolymers, characterized by UV-vis and FT IR spectroscopy, reached 1.22 mol % of the oxadiazole units relative to anhydride groups at the maximum (PSMA-4). Electric and optical properties of the copolymers were studied. The currents obtained depend strongly on the content of oxadiazole units in the copolymers. Currents measured in PSMA-4 were more than two orders of magnitude higher than those measured in the copolymers without oxadiazole. Using polymer blends made of poly(9,9-dihexadecylfluorene-2,7-diyl) and PSMA-4, blue light-emitting devices were fabricated and their photoluminescence and electroluminescence spectra were measured.     

Microfiltration membranes with pH dependent property prepared from poly(methacrylic acid) grafted polyethersulfone powder

Poly(methacrylic acid) (PMAA) grafted polyethersulfone (PES) powder was prepared by γ-ray irradiation-induced graft polymerization. The existing of the PMAA side chains in the grafted powder was proved by FT-IR spectroscopy. Then, pH dependent microfiltration (MF) membranes were cast from PES-g-PMAA powder with different degree of grafting (DG) under phase inversion method. The contact angle, mean pore size and swelling behavior of MF membranes were measured. The morphology was studied and the water filtration property was also tested. The results showed that the mean pore sizes and filtration properties of MF membranes cast from PES-g-PMAA powder varied with pH. In the most variant case, the flux of acid solution was about four times as that of basic solution for the MF membrane cast from PES-g-PMAA with DG of 20.0%.     

A novel covalent functionalisation of poly (styrene-alt-maleic anhydride) with 4-amino benzo-9-crown-3 ether

The grafting of 4-amino benzo-9-crown-3 ether to poly (styrene-alt-maleic anhydride) has been described. The covalent grafting of crown ether has led to a considerable increase in the solubility of polymer in organic solvents such as dimethyl sulphoxide, dimethylformamide and tetrahydrofuran. The highest solubility was attained in DMF and DMSO. The covalently bonded 4-benzo-9-crown-3 ether allowed the hosting of Li⁺. The covalently grafted crown ether to polymer was identified by infrared spectroscopy and thermogravimetric analysis methods.     

Supercritical carbon dioxide assisted synthesis of amphiphilic graft copolymers based on poly(styrene-co-maleic anhydride) with methoxyl poly(ethylene glycol) side chains

Supercritical carbon dioxide (scCO2) was used as a reaction medium in synthesizing amphiphilic graft copolymers composed of poly(styrene-co-maleic anhydride) (SMA) backbones and methoxyl poly(ethylene glycol) (MPEG) side chains via esterification.The synthesized copolymers were characterized by Four     

Dynamic behavior of ultrahigh molecular weight poly(methyl methacrylate) in semidilute solutions

The paper presents some rheological investigations on ultrahigh molecular weight (u.h.m.w.) (M_w > 10⁷) poly(methyl methacrylate) in semidilute solutions. The main interest was to study the viscoelastic behavior of the semidilute solutions at different concentrations and temperatures. In the 60‐600 rad/s frequency range, the experimental data show a predominantly elastic response (G′ > G″) for the long poly(methyl methacrylate) chains in toluene.     

Thermo-oxidative degradation of ultrahigh molecular weight poly(ethylene oxide) in volatile organic solvents

The degradation of ultrahigh molecular weight poly(ethylene oxide) (UHMWPEO) was investigated in three volatile organic solvents, methanol, chloroform, and tetrahydrofuran. Particularly, degradation rate was determined by means of Ubbelohde viscometry and degradation products were characterized by using electron spin resonance spectroscopy (ESR) and Fourier transform infrared spectroscopy (FTIR). The highest degradation rate was observed for UHMWPEO in tetrahydrofuran, with the lowest one in methanol. The ESR results showed that PEO-C• and •OH radicals were produced during the degradation process. Among these selected solvents, tetrahydrofuran was found to generate free radicals through an autoxidation mechanism. This would accelerate the degradation of UHMWPEO, resulting in the observed highest degradation rate in the UHMWPEO/tetrahydrofuran solution. Esters were also detected in the degradation products of these UHMWPEO solutions, while formates and formate ions were generated in the solutions of UHMWPEO/tetrahydrofuran and UHMWPEO/cloroform except for PEO/methanol. Furthermore, the degradation mechanism of UHMWPEO was deduced. This work enabled an in-depth understanding on the thermo-oxidative degradation mechanism of UHMWPEO in representative organic solvents, which would be instructive for developing optimal solution-based processing technique of UHMWPEO.     

Blending,geldrawing and UV-photolysis of ultrahigh molecular weight polyethylene and poly(di-n-pentylsilylene)

Blending of drawable UHMW-PE with poly(di-n-pentylsilylene) by concurrent gel crystallization was performed and the resulting blends drawn to tapes of high strength and high modulus. As shown by electron microscopy, poly(di-n-pentylsilylene) could be dispersed as nanometer-sized domains in the UHMW-PE matrix and afterwards cooriented by ultradrawing. In the drawn tapes the crystallinity of the PE component was unaffected by blending. Polarized FTIR-spectroscopy demonstrated high orientation of both blend components. Corresponding UV-spectra showed local conformational changes of the polysilylene chains, as well as strong UV-dichroism. Intensive UV-radiation yielded selective decomposition of the polysilylene while the PE was little affected. Reactive intermediates resulted in the formation of Si-H groups which might be helpful to introduce chemical links between PE fibrils.     

Synthesis of Surface-Functionalized Poly(styrene-co-butadiene) Nanoparticles via Controlled/Living Radical Mini-emulsion Copolymerization Stabilized by Ammonolyzed Poly(styrene-alt-maleic anhydride) (SMA) RAFT Agent

A process for reversible addition-fragmentation chain transfer (RAFT) radical polymerization in a mini-emulsion system stabilized by ammnolyzed poly(styrene-alt- maleic anhydride) copolymer (SMA) as an amphiphilic macro RAFT agent has been applied to the copolymerization of styrene and butadiene to prepare nanoparticles. First, for the RAFT polymerization of styrene, the results of molecular weights (Mns) and polydispersity index (PDIs) determined by GPC showed that the RAFT mini-emulsion polymerization of styrene exhibited good controlled/living nature with a lower degree of aminolysis (～30%). Second, for the copolymerization of styrene and butadiene, before the gel point the molecular weight growth was followed during the polymerization by GPC and the results revealed that the GPC curve moves to the higher molecular weight indicating the formation of the copolymer. At low conversion, molecular weights (Mns) are in good agreement with theoretical prediction. The microphase separation of the copolymer nanoparticles was confirmed by transmission electron microscopy (TEM).     

Synthesis of high molecular weight and narrow molecular weight distribution poly(acrylonitrile) via RAFT polymerization

Well‐defined polyacrylonitrile (PAN) of high viscosity‐average molecular weight (M_η = 405,100 g/mol) was successfully synthesized using reversible addition‐fragmentation chain transfer polymerization. The polymerization exhibits controlled characters: molecular weights of the resultant PANs increasing approximately linearly with monomer conversion and keeping narrow molecular weight distributions. The addition of 0.01 equiv (relative to monomer acrylonitrile) of Lewis acid AlCl₃ in the polymerization system afforded the obtained PAN with an improved isotacticity (by 8%). In addition, the influence of molecular weights and molecular weight distributions of PANs on the morphology of the electrospun fibers was investigated. The results showed that, under the same conditions of electrospinning, average diameter (247–1094 nm) of fibers increased with molecular weights of PANs, and it was much easier to get “uniform” diameter fibers while using PANs with narrow molecular weight distributions as the precursor of electrospinning. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Gel processing of electrically conductive blends of poly(3-octylthiophene) and ultrahigh molecular weight polyethylene

The mechanical and electrical properties of solution-processed [or gel-spun] blends of poly(3-octylthiophene) and ultrahigh molecular weight polyethylene are discussed. Tensile drawing at elevated temperatures of the phase-separated blends resulted in significant improvements of the mechanical properties, in comparison with those of the neat conducting polymer, with values of the Young's modulus reaching > 40 GPa and tensile strengths in excess of 2 GPa. Doping of the undrawn polyblend fibers with iodine vapor or FeCl₃ resulted in materials of useful levels of electrical conductivity covering the full range of 10^?15 to 10 S/cm. A distinct percolation threshold for electrical conductivity was not observed, even at poly(3-octylthiophene) concentrations as low as 0.5 w/w %; the electrical conductivity of the latter blend, after doping with iodine vapor, was 8 × 10^?8 S/cm.     

Effects of divinylbenzene‐maleic anhydride copolymer hollow microspheres on crystallization behaviors,mechanical properties and heat resistance of poly(l‐lactide acid)

Divinylbenzene‐maleic anhydride copolymer hollow microspheres (DMs) were used as novel organic nucleating agents to promote crystallization of poly(l‐lactide acid) (PLLA). The effects of these DMs on crystal behaviors of the PLLA were investigated by differential scanning calorimeter (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WAXD). Both isothermal and non‐isothermal processes in DSC demonstrated that the DMs significantly altered the crystal behaviors of PLLA as both crystallization velocity and degree of crystallinity increased with increasing DM loadings from 0 to 3%. Our POM results also indicated that as nucleating agents, the DMs promoted nucleating densities and decreased spherulitic sizes. In addition, WAXD suggeted that the addition of DMs did not induce new types of crystals. Finally, our results showed that the ductility of the PLLA was enhanced by a small amount of DMs during the PLLA crystallization process since 0.5% DMs added to the PLLA resulted in 1.4‐fold increase in the elongation at break in comparision with the neat PLLA.     

Laser light scattering study of the degradation of poly(sebacic anhydride) nanoparticles

Poly(sebacic anhydride) (PSA) is biocompatible and degradable in basic media. We micronized this water‐insoluble polymer into stable polymeric nanoparticles via a microphase inversion. Such PSA nanoparticles degraded much faster than bulk PSA. The influence of the surfactant, temperature, and pH on the degradation of the PSA nanoparticles was investigated by a combination of static and dynamic laser light scattering. Under each condition, the degradation rate was nearly constant up to a 75% weight loss; that is, the degradation was close to zero‐order. The degradation rate increased with the pH and temperature. Biomedical applications of such PSA nanoparticles are suggested. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 703–708, 2001     

Electron diffraction and computer modeling of poly(naphthalic anhydride) crystal structure

Single crystals of poly(naphthalic anhydride) (PNA) have been grown using our confined thin film melt polymerization technique. Lamellae, 70–100 Å thick, are found for the crystals polymerized at 180°C with thinner lamellae for a 200°C polymerization temperature. In addition, irregular lath-shaped crystals are found for both polymerization temperatures, apparently formed by a solid-state polymerization process within the original needle-like monomer crystals. The crystal structure of PNA has been studied by electron diffraction (ED) and computer modeling based on seven different zonal ED patterns. It is found that, in most cases, two or three different zonal patterns are superimposed with a common plane, suggesting variable chain tilting even in individual lamellae. Shearing of the material shortly after the initiation of polymerization, permitted obtaining an additional [010] zone ED pattern. A monoclinic unit cell with one chain, two repeat units is proposed based on measurements of 21 independent reflections; the space group is Pc11; a = 6.26 Å, b = 4.33 Å, c = 18.60 Å, and α = 122.5°. The computer-simulated (Cerius²) molecular conformation and chain packing are described with the corresponding simulated electron diffraction patterns being in good agreement with the observed ones. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1575–1588, 1997     

Synthesis and characterization of novel degradable photocrosslinked poly(ether‐anhydride) networks

New degradable poly(ether‐anhydride) networks were synthesized by UV photopolymerization. Dicarboxylated poly(ethylene glycol) (PEG) or poly(tetramethylene glycol) (PTMG) was reacted with an excess of methacrylic anhydride to form dimethacrylated macromers containing anhydride linkages. The percent of conversion for the macromer formation was more than 80% at 60 °C after 24 h. ¹H NMR and IR spectroscopies show the presence of anhydride linkages in the macromer. In vitro degradation studies were carried out at 37 °C in PBS with crosslinked polymer networks formed by UV irradiation. All PEG‐based polymers degraded within 2 days, while PTMG‐based polymers degraded by 50% of the initial weight after 14 days. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1277–1282, 2000