Strategies toward biocompatible artificial implants: Grafting of functionalized poly(ethylene glycol)s to poly(ethylene terephthalate) surfaces

Epoxide and aldehyde end‐functionalized poly(ethylene glycol)s (PEGs) (M_w = 400, 1000, 3400, 5000, and 20,000) were grafted to poly(ethylene terephthalate) (PET) film substrates that contained amine or alcohol groups. PET‐PAH and PET‐PEI were prepared by reacting poly(allylamine) (PAH) and polyethylenimine (PEI) with PET substrates, respectively; PET‐PVOH was prepared by the adsorption of poly(vinyl alcohol) (PVOH) to PET substrates. Grafting was characterized and quantified by the increase of the intensity of the PEG carbon peak in the X‐ray photoelectron spectra. Grafting yield was optimized by controlling reaction parameters and was found to be substrate‐independent in general. Graft density consistently decreased as PEG chain length was increased. This is likely due to the higher steric requirement of higher molecular weight PEG molecules. Water contact angles of surfaces containing long PEG chains (3400, 5000, and 20,000) are much lower than those containing shorter PEG chains (400 and 1000). This indicates that longer PEG chains are more effective in rendering surfaces hydrophilic. Protein adsorption experiments were carried out on PET‐ and PEG‐modified derivatives using collagen, lysozyme, and albumin. After PEG grafting, the amount of protein adsorbed was reduced in all cases. Trends in surface requirements for protein resistance are: surfaces with longer PEG chains and higher chain density, especially the former, are more protein resistant; PEG grafted to surfaces containing branched or network polymers is not effective at covering the underlying substrate, and thus does not protect the entire surface from protein adsorption; and substrates containing surface charge are less protein‐resistant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5389–5400, 2004     

Dense passivating poly(ethylene glycol) films on indium tin oxide substrates

We describe the formation and characterization of surface-passivating poly(ethylene glycol) (PEG) films on indium tin oxide (ITO) glass substrates. PEG chains with a molecular weight of 2000 and 5000 D were covalently attached to the substrates in a systematic approach using different coupling schemes. The coupling strategies included the direct grafting with PEG-silane, PEG-methacrylate, and PEG-bis(amine), as well as the two-step functionalization with aldehyde-bearing silane films and subsequent coupling with PEG-bis(amine). Elemental analysis by X-ray photoelectron spectroscopy (XPS) confirmed the successful surface modification, and XPS and ellipsometry provided values for film thicknesses. XPS and ellipsometry thickness values were almost identical for PEG-silane films but differed by up to 400% for the other PEG layers, suggesting a homogeneous layer for PEG-silane but an inhomogeneous distribution for other PEG coatings on the molecularly rough ITO substrates. Atomic force microscopy (AFM) and water contact angle goniometry confirmed the different degrees of surface homogeneity of the polymer films, with PEG-silane reducing the AFM rms surface roughness by 50% and the water contact angle hysteresis by 75% compared to uncoated ITO. The ability of the PEG layers to passivate the substrate against the nonspecific adsorption of biopolymers was tested using fluorescence-labeled immunoglobulin G and DNA oligonucleotides in combination with fluorescence microscopy. The results indicate a positive relationship between film density and homogeneity on one hand and the ability to passivate against biopolymer adhesion on the other hand. The most homogeneous layers prepared with PEG-silane reduced the nonspecific adsorption of fluorescence-labeled DNA by a factor of 300 compared to uncoated ITO. In addition, the study finds that the ratio of film thicknesses derived by ellipsometry and XPS is a useful parameter to quantify the structural integrity of PEG layers on molecularly rough ITO surfaces. The findings may be applied to characterize PEG or other polymeric films on similarly coarse substrates.     

Self-assembled monothiol-terminated hyperbranched polyglycerols on a gold surface: a comparative study on the structure, morphology, and protein adsorption characteristics with linear poly(ethylene glycol)s

Monothiol-terminated hyperbranched polyglycerols (HPGs) were synthesized by ring-opening polymerization of glycidol from partially deprotonated 2,2'-dihydroxyethane disulfide as the initiator and subsequent reduction of the disulfide group. Two molecular weights of HPG thiols were synthesized. The molecular weights of the polymers were determined by MALDI-TOF analysis, and the presence of thiol was verified by Ellman's assay. The self-assembly of HPG thiols on gold was studied and compared with that of linear poly(ethylene glycol) (PEG) thiols utilizing various surface analysis techniques. Monothiol-functionalized HPGs readily adsorbed to a gold surface and formed highly uniform thin films on the surface. The graft density of the HPG layer decreased with an increase in the molecular weight of the polymer. The amount of polymer on the surface increased with increasing incubation concentration and saturated above 6 g/L polymer concentration. Generally, HPG thiols gave lower graft density compared to linear PEG thiols of similar molecular weight. AFM morphological studies showed that HPG thiols form more uniform and smooth surface films compared to PEG thiols. Incubation of a polymer-coated surface (HPG thiols and PEG thiols) with bovine serum albumin and immunoglobulin showed that the high molecular weight hyperbranched polyglycerol was more resistant to protein adsorption than linear PEG of similar molecular weight or lower molecular weight HPG. The protein adsorption decreased with increasing graft density of the HPG chains on the surface. Our results show that HPG could be a good alternative to PEG in the development of nonfouling functional surfaces.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

The Synthesis of Poly(ethylene oxide)-Block-Polybutylacrylate

ＴｈｅＳｙｎｔｈｅｓｉｓｏｆＰｏｌｙ（ｅｔｈｙｌｅｎｅｏｘｉｄｅ）┐Ｂｌｏｃｋ┐Ｐｏｌｙｂｕｔｙｌａｃｒｙｌａｔｅ＊＊ＳｕｐｐｏｒｔｅｄｂｙｔｈｅＮａｔｉｏｎａｌＮａｔｕｒａｌＳｃｉｅｎｃｅＦｏｕｎｄａｔｉｏｎｏｆＣｈｉｎａａｎｄＤｏｃｔｏｒａｌｆｏ...     

PH effects in the complex formation and blending of poly(acrylic acid) with poly(ethylene oxide)

The effect of pH on the complex formation between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) has been studied in aqueous solutions by turbidimetric and fluorescent methods. It was shown that the formation of insoluble interpolymer complexes is observed below a certain critical pH of complexation (pH(crit1)). The formation of hydrophilic interpolymer associates is possible above pH(crit1) and below a certain pH(crit2). The effects of polymer concentrations in solution and PEO molecular weight as well as inorganic salt addition on these critical pH values were studied. The polymeric films based on blends of PAA and PEO were prepared by casting from aqueous solutions with different pHs. These films were characterized by light transmittance measurements and differential scanning calorimetry. The existence of the pH value above which the polymers form an immiscible blend was demonstrated. The transitions between the interpolymer complex, miscible blend, and immiscible blend caused by pH changes are discussed. The recommendations for preparation of homogeneous miscible films based on compositions of poly(carboxylic acids) and various nonionic water-soluble polymers are presented.     

Highly ion conductive poly(ethylene oxide)-based solid polymer electrolytes from hydrogen bonding layer-by-layer assembly

We report the development of a solid polymer electrolyte film from hydrogen bonding layer-by-layer (LBL) assembly that outperforms previously reported LBL assembled films and approaches battery integration capability. Films were fabricated by alternating deposition of poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) layers from aqueous solutions. Film quality benefits from increasing PEO molecular weight even into the 10(6) range due to the intrinsically low PEO/PAA cross-link density. Assembly is disrupted at pH near the PAA ionization onset, and a potential mechanism for modulating PEO:PAA ratio within assembled films by manipulating pH is discussed. Ionic conductivity of 5 x 10(-5) S/cm is achievable after short exposure to 100% relative humidity (RH) for plasticization. Adding free ions by exposing PEO/ PAA films to lithium salt solutions enhanced conductivity to greater than 10(-5) S/cm at only 52% RH and tentatively greater than 10(-4) S/cm at 100% RH. The excellent stability of PEO/PAA films even when exposed to 1.0 M salt solutions led to an exploration of LBL assembly with added electrolyte present in the adsorption step. Fortuitously, the modulation of PEO/PAA assembly by ionic strength is analogous to that of electrostatic LBL assembly and can be attributed to electrolyte interactions with PEO and PAA. Dry ionic conductivity was enhanced in films assembled in the presence of salt as compared to films that were merely exposed to salt after assembly, implying different morphologies. These results reveal clear directions for the evolution of these promising solid polymer electrolytes into elements appropriate for electrochemical power storage and generation applications.     

Comblike poly(ethylene oxide)/hydrophobic C6 branched chitosan surfactant polymers as anti-infection surface modifying agents

A series of structurally well-defined poly(ethylene oxide)/hydrophobic C₆ branched chitosan surfactant polymers that undergo surface induced self assembly on hydrophobic biomaterial surfaces were synthesized and characterized. The surfactant polymers consist of low molecular weight (M_w) chitosan backbone with hydrophilic poly(ethylene oxide) (PEO) and hydrophobic hexyl pendant groups. Chitosan was depolymerized by nitrous acid deaminative cleavage. Hexanal and aldehyde-terminated PEO chains were simultaneously attached to low M_w chitosan hydrochloride via reductive amination. The surfactant polymers were prepared with various ratios of the two side chains. The molecular composition of the surfactant polymers was determined by FT-IR and ¹H NMR. Surface active properties at the air–water interface were determined by Langmuir film balance measurements. The surfactant polymers with PEO/hexyl ratios of 1:3.0 and 1:14.4 were used as surface modifying agents to investigate their anti-infection properties. E. coli adhesion on Silastic^® surface was decreased significantly by the surfactant polymer with PEO/hexyl 1:3.0. Surface growth of adherent E. coli was effectively suppressed by both tested surfactant polymers.     

Immobilization of poly(ethylene oxide) on polyethylene using a plasma-induced graft copolymerization process

A radio-frequency glow discharge induced graft copolymerization process has prepared a PAAc-grafted PE film in this present study. Poly(ethylene oxide) (PEO) was then covalently immobilized onto PAAc-grafted PE film by a chemical coupling reaction. Carboxylic groups were introduced onto the surface of PE film by exposing the film to an Ar plasma, and the plasma-treated film was then next reacted with a 50% acrylic acid aqueous solution. These functional groups were reacted with bisamino PEO by a coupling agent CMC. ESCA, IR, and water contact angle studies were conducted for characterizing the surfaces of these films during the varied stages of the reaction. Increasing the molecular weight of the PEO attached to the PAAc-grafted PE resulted in an increased wettability of the films. © 1993 John Wiley & Sons, Inc.     

Specific interactions in blends of poly(ethylene oxide) and poly(bisphenol A-co-epichlorohydrin): FTIR and thermal study

Blends of poly(ethylene oxide) (PEO) of high molecular weight with poly(bisphenol A-co-epichlorohydrin) (PBE) with high epoxy equivalent were studied spectroscopically, thermally and morphologically. As similar systems of low molecular weight, a single T_g was observed for all blends, indicating miscibility. A progressive decrease in the degree of crystallinity and in the size of the PEO spherulites as the PBE is added is also observed. Quantitative analysis from FTIR spectra provided determination of specific interactions between the constituents and their variation with PEO content. Simulations were performed utilising the spectra of the pure polymers to confirm that the observed changes in the experimental spectra of the blends were due to interaction between the polymers.     

The interfacial tension of poly(ethylene oxide) and poly(propylene oxide) oligomers

Summary The interfacial tensions of a series of poly(ethylene oxides) (PEO) and poly(propylene oxides) (PPO) have been measured using a pendant drop technique. A drop of PEO was formed under the PPO, in a thermostatted cell usually at 73 °C, and it was photographed using parallel monochromatic light from a laser.The interfacial tensions were measured for a series of polymers of different molecular weights and were found to increase with increasing PPO molecular weight but to decrease slightly with increasing PEO molecular weight. The dependence on PPO molecular weight is explained as due to the adsorption of hydroxy end groups of the PPO at the PEO interface. When these end groups were "replaced by methoxy groups, the adsorption no longer took place and the interfacial tension increased.

---

Zusammenfassung Die Grenzflächenspannungen einer Reihe von Polyäthylenoxyden (PEO) und Polypropylenoxyden (PPO) wurden mittels der Methode des hängenden Tropfens gemessen. Ein Tropfen aus PEO wurde erzeugt unter PPO in einer temperierten Zelle bei gewöhnlich 73 ° C und wurde in parallelem monochromatischem Licht eines Lasers photographiert.Die Grenzflächenspannungen wurden für eine Reihe von Polymeren mit unterschiedlichem Molekulargewicht gemessen und nahmen zu mit steigendem PPO-Molekulargewicht, nahmen aber leicht ab mit zunehmendem PEO Molekulargewicht. Die Abhängigkeit vom PPO Molekulargewicht wird erklärt als Effekt der Adsorption von Hydroxyl-Endgruppen des PPO an der PEO Grenzfläche. Ersetzt man diese Endgruppen durch Methoxyl-Gruppen, beobachtet man keine Adsorption und die Grenzflächenspannung nimmt zu.

---

---

With 2 figures and 4 tables     

Chemical modification of butyl rubber. I. Synthesis and properties of poly(ethylene oxide)-grafted butyl rubber

A new amphiphilic polymer, i.e., poly(ethylene oxide) (PEO)-grafted butyl rubber (IIR-g-PEO), was synthesized by chemical modification of chlorinated butyl rubber (CIIR). This synthesis was based on the reaction between chlorine in CIIR and potassium salt of polyethylene glycol monomethyl ether (PEGM). PEGM's with molecular weights of 750 and 2000 were used. The maximum grafting percent of the resulted copolymers after the purification was ca. 45%, regardless of the molecular weight of PEGM. The microphase separated structure was observed in the films of IIR-g-PEOs. IIR-g-PEO, whose PEO molecular weight was 2000 and whose PEO content was 23.8 wt %, swelled 3.1% in water, and it was six times larger than the swelling of CIIR. The hydrophilicity of grafted polymers depended on the molecular weight of PEO side chains and PEO content. Even when the PEO contents were same in the polymers which were grafted PEGM-750 and PEGM-2000, their swellings in organic solvents were not equal. It was due to the difference of the microphase-separated structures of the grafted polymers. IIR-g-PEO, whose PEO molecular weight was 750 and whose PEO content was 10.3 wt %, swelled 1.5% in water, but showed an excellent emulsifying ability, where an oil-in-water-type emulsion was formed. © 1993 John Wiley & Sons, Inc.     

Adsorption of poly(ethylene oxide)-block-polylactide copolymers on polylactide as studied by ATR-FTIR spectroscopy

In this study, the adsorption of amphiphilic poly(ethylene oxide)-block-polylactide (mPEO-PLA) copolymers from a selective solvent onto a polylactide surface was studied as a method of polylactide surface modification and its effect on nonspecific protein adsorption was evaluated. A series of well defined mPEO-PLA copolymers was prepared to investigate the effect of copolymer composition on the resulting PEO chain density and on the surface resistance to protein adsorption. The copolymers contained PEO blocks with molecular weights ranging between 5600 and 23,800 and with 16-47 wt% of PLA. The adsorption of both the copolymers and bovine serum albumin was quantified by attenuated total reflection FTIR spectroscopy (ATR-FTIR). In addition to the adsorbed copolymer amount, its actual composition was determined. The PEO chain density on the surface was found to decrease with the molecular weight of the PEO block and to increase with the molecular weight of the PLA block. The adsorbed copolymers displayed the ability to reduce protein adsorption. The maximum reduction within the tested series (by 80%) was achieved with the copolymer containing PEO of MW 5600 and a PLA block of the same MW.     

Drying dissipative structures of aqueous solution of poly (ethylene glycol) on a cover glass

Macroscopic and microscopic dissipative structural patterns formed in the course of drying a series of poly (ethylene glycol) (PEG) having molecular weights ranging from 1,000 to 2×10⁶ in aqueous solution have been studied on a cover glass. The broad ring patterns of the hill accumulated with the polymers are formed irrespective of the molecular weights of PEG molecules. The single round hills are formed also in the center in the macroscopic scale, when the molecular weight is large. The characteristic convection flow of the polymers and the interactions among the polymers and substrate are important for the macroscopic pattern formation. Cross-like fractal patterns are observed, especially for the diluted solutions in the microscopic scale. These patterns are determined mainly by the electrostatic and polar interactions between the polymers and/or between the polymer and the substrate in the course of solidification. Interestingly, these microscopic patterns are reflected based on the shape and size of the PEG polymers.     

Protein-resistant poly(ethylene oxide)-grafted surfaces: chain density-dependent multiple mechanisms of action

A clear understanding of the mechanisms responsible for the protein-resistant nature of end-tethered poly(ethylene oxide) (PEO) surfaces remains elusive. A barrier to improved understanding is the fact that many of the factors involved (chain length, chain density, hydration, conformation, and distal chemistry) are inherently correlated. We hypothesize that, by comparing systems of variable but precisely known chain density, it should be possible to gain additional insight into the effects of the other factors. To evaluate this hypothesis, chain-end-thiolated PEOs were chemisorbed to gold-coated silicon wafers such that a range of chain densities was obtained. Three different PEOs were investigated: hydroxy-terminated chains of molecular weight 600 (600-OH), methoxy-terminated chains of molecular weight 750 (750-OCH3), and methoxy-terminated chains of molecular weight 2000 (2000-OCH3). In situ null ellipsometry was used to determine PEO chemisorption kinetics, ultimate PEO chain densities, protein adsorption kinetics, and ultimate protein adsorbed quantities. With this approach, it was possible to ascertain the effects of PEO distal chemistry (-OH, -OCH3), chain length, and layer hydration on protein adsorption. The data obtained suggested that properties related to chain density (conformational freedom, hydration) were the main determinants of protein resistance at chain densities up to a critical value of approximately 0.5 chain/nm2; at this value, protein adsorption was a minimum for the methoxy-terminated PEOs. For the hydroxyl-terminated PEO, adsorption leveled off at the critical value. Thus distal chemistry appears to be a major determinant of protein resistance at chain densities greater than the critical value.     

Polystyrene-block-poly(ethylene oxide) stars as surface films at the air/water interface

Star diblock copolymers containing polystyrene (PS) and poly(ethylene oxide) (PEO) were investigated as surface films at the air/water interface. Both classic and dendritic-like stars were prepared containing either a PS core and PEO corona or the reverse. The investigated polymers, consisting of systematic variations in architectures and compositions, were spread at the air/water interface, generating reproducible surface pressure-area isotherms. All of the films could be compressed to higher pressures than would be possible for pure PEO. For stars containing 20% or more PEO, three distinct regions appeared. At higher areas, the PEO absorbs in pancakelike structures at the interface with PS globules sitting atop. Upon compression, a pseudoplateau transition region appeared. Both regions strongly depended on PEO composition. The pancake area and the pseudoplateau width and pressure increased in a linear fashion with an increasing amount of PEO. In addition, minimum limits of PEO chain length and mass percentage were determined for observing a pseudoplateau. At small areas, the film proved less compressible, producing a rigid film in which PS dominated. Here, the film area increased with both molecular weight and the amount of PS. Comparison with pure linear PS showed the stars spread more, occupying greater areas. Among the stars, the PEO-core stars were more compact while the PS-core stars spread more. The influence of architecture in terms of the core/corona polymers and branching were also examined. The effects of architecture were subtle, proving less important than PEO chain length or mass percentage.     

Compact poly(ethylene oxide) structures adsorbed at the ethylammonium nitrate-silica interface

The adsorption of poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) onto silica from ethylammonium nitrate (a protic ionic liquid) has been investigated using colloid probe AFM force curve measurements. Steric repulsive forces were measured for PEO, confirming that PEO can compete with the ethylammonium cation and adsorb onto silica. The range of the repulsion increases with polymer molecular weight (e.g., from 1.4 nm for 0.01 wt % 10 kDa PEO to 40 nm for 0.01 wt % 300 kDa PEO) and with concentration (e.g., from 16 nm at 0.001 wt % to 78 nm at 0.4 wt % for 300 kDa PEO). Fits to the force curve data could not be obtained using standard models for a polymer brush, but excellent fits were obtained using the mushroom model, suggesting the adsorbed polymer films are compressed and relatively poorly solvated. No evidence for adsorption of 3.5 kDa PPO could be detected up to its solubility limit.     

Protein adhesion on silicon-supported hyperbranched poly(ethylene glycol) and poly(allylamine) thin films

Hyperbranching poly(allylamine) (PAAm) and poly(ethylene glycol) (PEG) on silicon and its effect on protein adhesion was investigated. Hyperbranching involves sequential grafting of polymers on a surface with one of the components having multiple reactive sites. In this research, PAAm provided multiple amines for grafting PEG diacrylate. Current methodologies for generating PEG surfaces include PEG-silane monolayers or polymerized PEG networks. Hyperbranching combines the nanoscale thickness of monolayers with the surface coverage afforded by polymerization. A multistep approach was used to generate the silicon-supported hyperbranched polymers. The silicon wafer surface was initially modified with a vinyl silane followed by oxidation of the terminal vinyl group to present an acid function. Carbodiimide activation of the surface carboxyl group allowed for coupling to PAAm amines to form the first polymer layer. The polymers were hyperbranched by grafting alternating PEG and PAAm layers to the surface using Michael addition chemistry. The alternating polymers were grafted up to six total layers. The substrates remained hydrophilic after each modification. Static contact angles for PAAm (32-44 degrees) and PEG (33-37 degrees) were characteristic of the corresponding individual polymer (30-50 degrees for allylamine, 34-42 degrees for PEG). Roughness values varied from approximately 1 to 8 nm, but had no apparent affect on protein adhesion. Modifications terminating with a PEG layer reduced bovine serum albumin adhesion to the surface by approximately 80% as determined by ELISA and radiolabel binding studies. The hyperbranched PAAm and PEG surfaces described in this paper are nanometer-scale, multilayer films capable of reducing protein adhesion.     

Thermal oxidation of blends of poly(ethylene oxide) and poly(methyl methacrylate)

Thermal oxidation of poly(ethylene oxide) (PEO) and its blends with poly(methyl methacrylate) (PMMA) were studied using oxygen uptake measurements. The rates of oxidation and maximum oxygen uptake contents were reduced as the content of PMMA was increased in the blends. The results were indicative of a stabilizing effect by PMMA on the oxidation of PEO. The oxidation reaction at 140°C was stopped at various stages and PMMA was separated from PEO and its molecular weights were measured by gel permeation chromatography (GPC). The decrease in the number-average molecular weight of PMMA was larger as the content of PEO increased in the blends. The visual appearance of the films suggested that phase separation did not occur after thermal oxidation. The activation energy for the rates of oxidation in the blends was slightly increased compared to pure PEO. © 1992 John Wiley & Sons, Inc.     

Surface immobilization of poly(ethylene oxide): Structure and properties

We covalently immobilized poly(ethylene oxide) (PEO) chains onto a fluorinated ethylene propylene copolymer (FEP) surface. On the FEP surface, aldehyde groups were first deposited by plasma polymerization of acetaldehyde or acrolein. Then, amino‐PEO chains were immobilized through Schiff base formation, which was followed by reduction stabilization with sodium cyanoborohydride. The PEO‐grafted polymer surfaces thus prepared were characterized by X‐ray photoelectron spectroscopy (XPS), atomic force microscopy, contact‐angle measurements, and protein adsorption. The dramatic increase in the C O intensity of the high‐resolution XPS C 1s spectrum, together with an overall increase in oxygen content, indicated the successful attachment of PEO chains onto the acetaldehyde plasma surfaces. The amount of grafted PEO chains depended on the superfacial density of the plasma‐generated aldehyde groups. The grafted monoamino‐PEO chains formed a brushlike structure on the polymer surface, whereas the bisamino‐PEO chains predominately adopted a looplike conformation. The PEO surface had a regular morphology with greater roughness than the aldehyde surface underneath. Surface hydrophilicity increased with the grafting of PEO. Also, the bisamino‐PEO‐grafted surface had slightly higher surface hydrophilicity than its monoamino‐PEO counterpart. These PEO coatings reduced fibrinogen adsorption by 43% compared with the substrate FEP surface. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2323–2332, 2000