Extractive separation of Cu<Superscript>2+</Superscript>–Co<Superscript>2+</Superscript> and Ni<Superscript>2+</Superscript>–Co<Superscript>2+</Superscript> mixtures using <Emphasis Type="Italic">N</Emphasis>-salicylideneaniline

A study on the extraction of copper(II), cobalt(II), and nickel(II) from solutions containing ions of both metals with N-salicylideneaniline(SAN) in chloroform has been realized. Distribution of the metal ions in wide range of pH has been studied. Extraction of copper(II) was always favored over that of cobalt(II). Extraction of copper(II) from binary metal solution is selective and it can be quantitatively separated from cobalt(II). The equilibrium constant of the extraction of cobalt and nickel from an aqueous solution containing both metals using SAN were evaluated. The separation factors for cobalt and nickel were expressed as a function of the distribution of nickel and cobalt. From these results, salicylideneaniline is an adequate extractant for extractive separation of such mixtures.     

High-performance liquid chromatographic determination of uranium using solvent extraction and bis(salicylaldehyde) tetramethylethylenediimine as complexing reagent

The reagent bis(salicylaldehyde)tetramethylethylenediimine has been used for the determination of dioxouranium(VI), based on complexation in aqueous solution at pH 6, followed by extraction in chloroform and HPLC determination on a Hypersil ODS (3 μm) column. The complex was eluted with the ternary mixture methanol-acetonitrile-water (40:30:30, v/v/v), with UV detection at 260 nm. Oxovanadium(IV), iron(III), copper(II), cobalt(II), nickel(II) and palladium(II) were completely separated and did not interfere in the determination of uranium. The linear calibration range and detection limits have been obtained. The method has been applied to the determination of uranium together with copper, iron and nickel in mineral ore samples.     

Extraction with long-chain amines-II Extraction and colorimetric determination of chromate

Highly selective extraction of chromate from slightly acidic solutions (0.1-0.2M sulphuric acid) with a chloroform solution of trioctylamine (Alamine 336-S) or trioctylmethylammonium chloride Aliquat 336-S) is described. Many metals such as iron, nickel, cobalt, copper, alluminium, zinc, are not extracted, even if present in large concentrations. Coextraction of vanadium(V) and uranium(VI) is prevented by addition of sodium chloride. Traces of extracted molybdenum are scrubbed with ammonium oxalate. Final determination of chromium is based on measurement of the absorbance of the extract at 445-450 nm.     

Extraction with long-chain amines-V Colorimetric determination of cobalt with nitroso-R salt

The colorimetric determination of cobalt with nitroso-R salt (NRS) has been modified and improved by the introduction of extraction of the Co-NRS chelate into a chloroform solution of trioctylmethylammonium chloride. Ammonium phosphate, fluoride and mainly citrate were used for masking iron, nickel, copper and calcium, which under the described conditions do not interfere even in 2000-fold excess. The method is very sensitive and permits determination of about 1 mug of cobalt per ml of the extractant.     

Extraction with long-chain amines-VIII Extraction of the chromium-DCTA complex and its colorimetric determination

Chromium(III) is extracted as the DCTA complex by ion-association with trioctylmethylammonium chloride (Aliquat 336-S), into chloroform, and stripped into 1M potassium nitrate for spectrophotometric measurement at 540 nm. Iron(III) copper(II) are removed beforehand by extraction whith phenylacetic acid. High concentrations of nickel or cobalt prevent complete extraction.     

The photometric determination of cobalt by extraction with b -nitroso-a-naphthol

An improved procedure has been described for the photometric determination of cobalt by extraction of the β-mtroso-α-naphthol complex with chloroform. This procedure can be applied in the presence of large amounts of foreign elements. Interfering elements are: gold, palladium, platinum and copper (above 25 mg).The method has been applied to the determination of cobalt in steels, non-ferrous alloys and nickel.     

Solid-liquid extraction as a preconcentration technique in trace element analysis Extraction of trace impurities from metal chlorides

Microgram quantities of iron, cobalt, copper, zinc and cadmium are extracted with various aqueous, organic and mixed solvents from chlorides of sodium, potassium, nickel, cadmium, barium and lead prepared by evaporation of aqueous sample solutions. An ultrasonic field accelerates the extraction, and satisfactory trace recoveries and separation factors are achieved in several systems within a reasonable time. The application to a polarographic determination and a two-stage separation technique are also described.     

Selective extraction of iron(III) from aqueous nitrate solution in the presence of cobalt(II), copper(II) and nickel(II) ions using bis(delta2-2-imidazolinyl)-5,5'-dioxime.

The feasibility of using bis(delta2-2-imidazolinyl)-5,5'-dioxime (H2L) for the selective extraction of iron(III) from aqueous solutions was investigated by employing an solvent-extraction technique. The extraction of iron(III) from an aqueous nitrate solution in the presence of metal ions, such as cobalt(II), copper(II) and nickel(II), was carried out using H2L in binary and multicomponent mixtures. Iron(III) extraction has been studied as a function of the pH, equilibrium time and extractant concentration. From the extracted complex species in the organic phase, iron(III) was stripped with 2 M HNO3, and later determined using atomic-absorption spectrometry. The extraction was found to significantly depend on the aqueous solution pH. The extraction of iron(III) with H2L increases with the pH value, reaching a maximum in the zone of pH 2.0, remaining constant between 2 and 3.5 and subsequently decreasing. The quantitative extraction of iron(III) with 5 x 10(-30 M H2L in toluene is observed at pH 2.0. H2L was found to react with iron(III) to form ligand complex having a composition of 1:2 (Fe:H2L).     

Extractive separation and spectrophotometric determination of tungsten as ferrocyanide

Tungsten, in amounts ranging from micrograms to milligrams, can be extracted into isoamyl alcohol, as the tungsten(V) ferrocyanide complex obtained by reduction of tungsten(VI) with tin(II) in 4M hydrochloric acid containing ferrocyanide. It can thus be separated from iron, cobalt, chromium, manganese, arsenic, antimony, bismuth, silicon, calcium and copper, their precipitation being prevented by addition of glycerol and, in the case of iron, sulphosalicyclic acid. Molybdenum, vanadium and nickel are not separated from tungsten, however. Tungsten can also be determined spectrophotometrically as tungsten(V) ferrocyanide. The absorbance of the brown complex is measured in aqueous solution or preferably after extraction into isoamyl alcohol. As many alloying elements interfere, they should be separated by the ferrocyanide extraction or other suitable method. Both the separation and the determination methods give satisfactory results with an overall error of not more than 0.5% in the analysis of practical samples containing low or high percentages of tungsten.     

The application of 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradecane to the extraction of metal ions

The use of 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradecane (Tet) in chloroform solutions provides quantitative extraction of lead(II), cadmium(II), copper(II) and zinc(II) at different pH values from solutions containing perchlorate and cyclohexanecarboxylic acid. Nickel(II) and cobalt(II) ions are not extracted quantitatively. Single extractions of mixtures of copper with transition metals gave the best separations for the copper/nickel system. Separations of copper from cobalt, lead, manganese and iron were less satisfactory.     

Determination of transition metal ions in tobacco as their 2-(2-quinolinylazo)-5-dimethylaminophenol derivatives using reversed-phase liquid chromatography with UV-VIS detection

This paper reports the utilization of solid-phase extraction and the reversed-phase high-performance liquid chromatography for the determination of six important transition metal ions: iron, cobalt, nickel, copper, zinc and manganese in tobacco with 2-(2-quinolinylazo)-5-dimethylaminophenol (QADMAP) as chelating reagent. Iron, cobalt, nickel, copper, zinc and manganese ions react with QADMAP to form colored chelates in the medium of acetic acid-sodium acetate buffer solution (pH 4.0). These chelates can be enriched by solid-phase extraction with Waters Sep-Pak-C18 cartridge, and eluted the retained chelates from cartridge with tetrahydrofuran. The chelates were separated on a Waters Nova-Pak-C18 column (150x3.9 mm, 5 microm) by gradient elution with methanol (containing 0.5% of acetic acid) and 0.05 mol/l pH 4.0 acetic acid-sodium acetate buffer solution as mobile phase at a flow-rate of 0.5 ml/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 10, 12, 8, 13, 17 and 22 ng/l, respectively. This method had been applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in tobacco with good results.     

A catalytic method for the determination of Nickel

The catalytic effect of nickel on the decomposition of permanganate in alkaline solution in the presence of acctodiphosphonic acid is used as a basis for a method for the determination of 0.1–0 7 p.p.m. of nickel. A solvent extraction procedure eliminates the interferences of silver, cobalt, copper and iron, and can be used to concentrate lower concentrations of nickel.     

Spectrophotometric simultaneous determination of cobalt, copper and nickel using nitroso-R-salt in alloys by partial least squares

Partial least squares modeling as a powerful multivariate statistical tool applied to spectrophotometric simultaneous determination of cobalt, copper, and nickel in aqueous solutions. The concentration range for cobalt, copper and nickel were 0.4-2.6, 0.6-3.4, 0.5-5.5 ppm, respectively. The experimental calibration set was composed with 36 sample solutions using a mixture design for three component mixtures. The absorption spectra were recorded from 470 to 600 nm. The effect of pH on the sensitivity and selectivity was studied according to net analyte signal (NAS). The values of root mean square difference (RMSD) for cobalt, copper and nickel using partial least squares (PLS) were 0.0192, 0.0263 and 0.0446 ppm, respectively. The effects of various cations and anions were investigated. The method was used to determination of cobalt, copper and nickel in two sample alloys based on copper, nickel and cobalt (known as cunico) and based on cobalt, nickel and iron (known as conife).     

Determination of cobalt, nickel, lead, bismuth and indium in ores, soils and related materials by atomic-absorption spectrometry after separation by xanthate extraction

A method for determining approximately 0.5, mug/g or more of cobalt, nickel and lead and approximately 3 mug/g or more of bismuth and indium in ores, soils and related materials is described. After sample decomposition and dissolution of the salts in dilute hydrochloric-tartaric acid solution, iron(III) is reduced with ascorbic acid and the resultant iron(II) is complexed with ammonium fluoride. Cobalt, nickel, lead, bismuth and indium are subsequently separated from iron, aluminium, zinc and other matrix elements by a triple chloroform extraction of their xanthate complexes at pH 2.00 +/- 0.05. After the removal of chloroform by evaporation and the destruction of the xanthates with nitric and perchloric acids, the solution is evaporated to dryness and the individual elements are ultimately determined in a 20% v/v hydrochloric acid medium containing 1000 mug/ml potassium by atomic-absorption spectrometry with an air-acetylene flame. Co-extraction of arsenic and antimony is avoided by volatilizing them as the bromides during the decomposition step. Small amounts of co-extracted molybdenum, iron and copper do not interfere.     

Selection of the counter-cation in the solvent extraction of anionic chelates: Spectrophotometric determination of trace amounts of cobalt with 2-nitroso-1-naphthol-4-sulphonic acid and tetrabutylammonium ion

The importance of selecting the most suitable counter-cation in the solvent extraction-spectrophotometric determination of an anionic metal chelate containing a sulphonic acid group is demonstrated and discussed. In the case of cobalt and 2-nitroso-1-naphthol-4-sulphonic acid (nitroso-NW acid), the most suitable counter-cation is the tetrabutylammonium ion (Bu(4)N(+)): in this case only the ion-pair of the anionic cobalt chelate is extracted into chloroform and the excess of the nitroso-NW acid remains in the aqueous phase. The absorption maximum of the chelate in chloroform is at 307nm, at which the molar absorptivity is 6.5 x 10(4)l.mole(-1).cm(-1). The absorbance of the reagent blank at 307 nm is less than 0.010. By use of nitroso-NW acid and Bu(4)N(+), trace amounts of cobalt may be determined in nickel salts and in iron and steel samples.     

The simultaneous determination of copper and nickel by solvent extraction and gas-liquid chromatography with bis (acetylpivalylmethane) ethylenediimine as reagent

The copper(II), nickel(II) and palladium(II) chelates of the bridged β-ketoamine, bis(acetylpivalylmethane) ethylenediimine, are described. The copper and nickel complexes are readily extracted by cyclohexane at pH 8.0 from aqueous solution. The gas chromatographic separation of the copper and palladium, the nickel and palladium, and the copper and nickel chelates is reported on a silicone gum rubber phase (E-350) supported on Universal B at 285°C. Optimal conditions for the complete separation of copper and nickel are reported; the solvent extraction—gas chromatographic procedures are applied to the determination of the individual metal ions (limit of detection, 1 ng) and to the simultaneous determination of copper and nickel in solution and in alloy samples. A rapid method for the determination of copper in domestic water samples is also described.     

Extraction of palladium(II) from hydrochloric acid solutions by (RS)-1-(4-chlorophenyl)-4,4-dimethyl-3-(1H-1,2,4-triazol-1-ylmethyl)-pentan-3-ol

The extraction properties of (RS)-1-(4-chlorophenyl)-4,4-dimethyl-3-(1H-1,2,4-triazol-1-ylmethyl)-pentan-3-ol (with chloroform as a diluent) with respect to palladium(II) were studied. Palladium(II) was found to be efficiently extracted by the reagent from 0.1–6 M HCl solutions by the coordination mechanism. The rate of palladium(II) recovery depends on the hydrochloric acid and chloride ion concentrations in the aqueous phase. Conditions for the selective separation of palladium(II) and copper(II) from nickel(II), cobalt(II), and iron(III) were determined.     

Extraction of some metal phenylacetates into chloroform

Phenylacetic acid has been found to be very useful as a reagent in the extraction of large quantities of certain ions, notable iron(III), cobalt(II), copper(II), lead, zinc, cadmium and uranyl. A 1M solution of the reagent in chloroform is used to extract up to 200 mg of certain ions from small volumes of aqueous phase. Selectivity is increased by pH control and masking.     

Spectrophotometric determination of cobalt in iron-, cobalt- and nickel-base alloys

A spectrophotometric method has been developed for the accurate determination of cobalt at milligram level, based on oxidation of the cobalt(II)-EDTA complex with gold(III) chloride at pH 4.0-6.5 and 100 degrees and measurement of the absorbance of the resultant violet cobalt(III)-EDTA complex at 535 nm. The precision is not affected by the presence of several metal ions; including coloured ones such as Cu(II), Ni(II) and Fe(III). However, chromium(III) interferes since it also forms a violet complex with EDTA, but can be removed by separation with pyridine. Practical application of the method is illustrated by the determination of cobalt in alloys based on iron, cobalt and nickel. Over the cobalt range 8-52% the error ranges from 0.1 to 0.3%.     

Pulse nebulization of chloroform and carbon tetrachloride extracts in flame atomic absorption spectrometry

The determination or cadmium, cobalt, copper, nickel and lead after extraction with tetramethylenedithiocarbamate into various solvents is achieved by injection of 50-μl aliquots of extract by pulse nebulization into an air-acetylene flame. The technique is particularly suitable for cadmium and lead extracted into chlorinated solvents, which must not continuously be nebulized into the flame. The performance of the technique is compared for chloroform, carbon tetrachloride, butyl acetate, methyl isobutyl ketone, toluene and xylene.