Bioglass thin films for biomimetic implants

Pulsed laser deposition (PLD) method was used to obtain bioglass (BG) thin film coatings on titanium substrates. An UV excimer laser KrF* (λ = 248 nm, τ = 25 ns) was used for the multi-pulse irradiation of the BG targets with 57 or 61 wt.% SiO₂ content (and Na₂O-K₂O-CaO-MgO-P₂O₅ oxides). The depositions were performed in oxygen atmosphere at 13 Pa and for substrates temperature of 400 °C. The PLD films displayed typical BG of 2-5 μm particulates nucleated on the film surface or embedded in. The PLD films stoichiometry was found to be the same as the targets. XRD spectra have shown, the glass coatings obtained, had an amorphous structure. One set of samples, deposited in the same conditions, were dipped in simulated body fluids (SBFs) and subsequently extracted one by one after several time intervals 1, 3, 7, 14 and 21 days. After washing in deionized water and drying, the surface morphology of the samples and theirs composition were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), IR spectroscopy (FTIR) and energy dispersive X-ray analysis (EDX). After 3-7 days the Si content substantially decreases in the coatings and PO₄³⁻ maxima start to increase in FTIR spectra. The XRD spectra also confirm this evolution. After 14-21 days the XRD peaks show a crystallized fraction of the carbonated hydroxyapatite (HAP). The SEM micrographs show also significant changes of the films surface morphology. The coalescence of the BG droplets can be seen. The dissolution and growth processes could be assigned to the ionic exchange between BG and SBFs.     

Biocompatible and bioactive nanostructured glass coatings synthesized by pulsed laser deposition: In vitro biological tests

We report on the synthesis by pulsed laser deposition with a KrF* excimer laser source (λ = 248 nm, τ = 25 ns) of bioglass thin films of 6P57 and 6P61 types. Physiology, viability, and proliferation of human osteoblast cells were determined by quantitative in vitro tests performed by flow cytometry on primary osteoblasts cultured on pulsed laser deposited bioglasses. Both types of glass films proved to be appropriate mediums for cell survival and proliferation. In a parallel investigation, cell morphology and adhesion to the surface was studied by fluorescence microscopy and scanning electron microscopy. Strong bonds between the materials and cells were found in both cases, as osteoblast pseudopodes penetrated deep into the material. According to our observations, the 6P57 glass films were superior with respect to viability and proliferation performances.     

Bioactive glass and hydroxyapatite thin films obtained by pulsed laser deposition

Bioactive glass (BG), calcium hydroxyapatite (HA), and ZrO₂ doped HA thin films were grown by pulsed laser deposition on Ti substrates. An UV KrF^* (λ = 248 nm, τ ≥ 7 ns) excimer laser was used for the multi-pulse irradiation of the targets. The substrates were kept at room temperature or heated during the film deposition at values within the (400-550 °C) range. The depositions were performed in oxygen and water vapor atmospheres, at pressure values in the range (5-40 Pa). The HA coatings were heat post-treated for 6 h in a flux of hot water vapors at the same temperature as applied during deposition. The surface morphology, chemical composition, and crystalline quality of the obtained thin films were studied by scanning electron microscopy, atomic force microscopy, and X-ray diffractometry. The films were seeded for in vitro tests with Hek293 (human embryonic kidney) cells that revealed a good adherence on the deposited layers. Biocompatibility tests showed that cell growth was better on HA than on BG thin films.     

Shallow hydroxyapatite coatings pulsed laser deposited onto Al2O3 substrates with controlled porosity: correlation of morphological characteristics with in vitro testing results

We studied the influence of porous Al₂O₃ substrates on Ce-stabilized ZrO₂-doped hydroxyapatite thin films morphology pulsed laser deposited on their top. The porosities of substrates were monitored by changing sintering temperatures and measured with a high pressure Hg porosimeter.The depositions were conducted in 50 Pa water vapors by multipulse ablation of the targets with an UV KrF* (λ = 248 nm, τ ∼ 25 ns) excimer laser. The surface morphology of synthesized nanostructures was investigated by scanning electron microscopy and atomic force microcopy. Ca/P ratio within the range 1.67-1.70 was found for hydroxyapatite coatings by energy dispersive spectroscopy.The films were further seeded with mesenchymal stem cells for in vitro tests. The cells showed good attachment and spreading uniformly covering the entire surface of samples. The complexity of film morphology which is increasing with substrate porosity was shown to have a positive influence on cultivated cells density.     

Effects of substrates on the structure and dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films

Ba(Sn_0.15Ti_0.85)O₃ (BTS) thin films were grown on Pt(1 1 1)/Ti/SiO₂/Si and LaNiO₃(LNO)/Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel processing technique, respectively. The BTS thin films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si and annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates exhibited strong (1 1 1) and perfect (1 0 0) orientations, respectively. The BTS thin films grown on un-annealed Pt(1 1 1)/Ti/SiO₂/Si substrates showed random orientation with intense (1 1 0) peak, while the films deposited on un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate exhibited random orientation with intense (1 0 0) peak, respectively. The dielectric constant of the BTS films deposited on annealed Pt(1 1 1)/Ti/SiO₂/Si, annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si, un-annealed Pt(1 1 1)/Ti/SiO₂/Si and un-annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrates was 512, 565, 386 and 437, respectively, measured at a frequency of 100 kHz. A high tunability of 49.7% was obtained for the films deposited on annealed LNO/Pt(1 1 1)/Ti/SiO₂/Si substrate, measured at the frequency of 100 kHz with an applied electric field of 200 kV/cm. The high tunability has been attributed to the (1 0 0) texture of the films and larger grain sizes.     

Structure and refractive index dispersive behavior of potassium niobate tantalate films prepared by pulsed laser deposition

Pure perovskite phase and crack-free KTa_0.5Nb_0.5O₃ thin films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. The structure and orientation were analyzed by X-ray diffraction. The optical properties were investigated by an ellipsometer. The relationship between the refractive index dispersive behavior and internal structure was analyzed by Sellmeier dispersion model and single electronic oscillator approximation. The parameters of room temperature monomial Sellmeier oscillator were calculated. And the refractive index dispersive parameter E₀/S₀ of KTa_0.5Nb_0.5O₃ thin films on Pt/Ti/SiO₂/Si substrates is (6.72 ± 0.04) × 10⁻¹⁴ eV m², which is consistent with those of KTN crystals and compounds with ABO₃ perovskite type structure.     

Influence of MgO and ZrO2 buffer layers on dielectric properties of Ba(Zr0.20Ti0.80)O3 thin films prepared by sol-gel processing

Ba(Zr_0.20Ti_0.80)O₃ (BZT) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates by a sol-gel process. The BZT thin films directly grown on Pt(1 1 1)/Ti/SiO₂/Si substrates exhibit highly (1 1 1) preferred orientation, while the films deposited on Pt(1 1 1)/Ti/SiO₂/Si substrates with MgO and ZrO₂ buffer layers show highly (1 1 0) preferred orientation. At 100 kHz, dielectric constants are 417, 311 and 321 for the BZT thin films grown on Pt(1 1 1)/Ti/SiO₂/Si, MgO and ZrO₂ buffered Pt(1 1 1)/Ti/SiO₂/Si substrates, respectively. The difference in dielectric properties of three BZT films can be attributed to the series capacitance effect, interface conditions and their orientations.     

Photoluminescence in amorphous (PbLa)TiO3 thin films deposited on different substrates

Pb_1−XLa_XTiO₃ thin films, (X=0.0; 13 and 0.27 mol%) were prepared by the polymeric precursor method. Thin films were deposited on Pt/Ti/SiO₂/Si (1 1 1), Si (1 0 0) and glass substrates by spin coating, and annealed in the 200-300°C range in an O₂ atmosphere. X-ray diffraction, scanning electron microscopy and atomic force microscopy were used for the microstructural characterization of the thin films. Photoluminescence (PL) at room temperature has been observed in thin films of (PbLa)TiO₃. The films deposited on Pt/Ti/SiO₂/Si substrates present PL intensity greater than those deposited on glass and silicon substrates. The intensity of PL in these thin films was found to be dependent on the thermal treatment and lanthanum molar concentration.     

Reduced dielectric loss and leakage current in CaCu3Ti4O12/SiO2/CaCu3Ti4O12 multilayered films

The CaCu₃Ti₄O₁₂/SiO₂/CaCu₃Ti₄O₁₂ (CCTO/SiO₂/CCTO) multilayered films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition method. It has been demonstrated that the dielectric loss and the leakage current density were significantly reduced with the increase of the SiO₂ layer thickness, accompanied with a decrease of the dielectric constant. The CCTO film with a 20 nm SiO₂ layer showed a dielectric loss of 0.065 at 100 kHz and the leakage current density of 6×10⁻⁷ A/cm² at 100 kV/cm, which were much lower than those of the single layer CCTO films. The improvement of the electric properties is ascribed to two reasons: one is the improved crystallinity; the other is the reduced free carriers in the multilayered films.     

Write-once blue laser recording using silicon doped SbOx thin films prepared by reactive dc-magnetron sputtering

Si:SbO_x films have been deposited by reactive dc-magnetron sputtering from a Sb target with Si chips attached in Ar + O₂ with the relative O₂ content 7%. The as-deposited films contained Sb metal, Sb₂O₃, SiO, Si₂O₃ and SiO₂. The crystallization of Sb was responsible for the changes of optical properties of the films. The results of the blue laser recording test showed that the films had good writing sensitivity for blue laser beam (406.7 nm), and the recording marks were still clear even if the films were deposited in air 60 days, which demonstrated that doping silicon in SbO_x films can improve the stability of SbO_x films. High reflectivity contrast of about 36% was obtained at a writing power 6 mW and writing pulse width 300 ns.     

Electrochemical and surface behavior of hydyroxyapatite/Ti film on nanotubular Ti-35Nb-xZr alloys

In this paper, we investigated the electrochemical and surface behavior of hydroxyapatite (HA)/Ti films on the nanotubular Ti-35Nb-xZr alloy. The Ti-35Nb-xZr ternary alloys with 3-10 wt.% Zr content were made by an arc melting method. The nanotubular oxide layers were developed on the Ti-35Nb-xZr alloys by an anodic oxidation method in 1 M H₃PO₄ electrolyte containing 0.8 wt% NaF at room temperature. The HA/Ti composite films on the nanotubular oxide surfaces were deposited by a magnetron sputtering method. Their surface characteristics were analyzed by field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS) and an X-ray diffractometer (XRD). The corrosion behavior of the specimens was examined through potentiodynamic and AC impedance tests in 0.9% NaCl solution. From the results, the Ti-35Nb-xZr alloys showed a solely β phase microstructure that resulted from the addition of Zr. The nanotubular structure formed with a diameter of about 200 nm, and the HA/Ti thin film was deposited on the nanotubular structure. The HA/Ti thin film-coated nanotubular Ti-35Nb-xZr alloys showed good corrosion resistance in 0.9% NaCl solution.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

F2 laser induced oxidation of inorganic material

Transparent SiO₂ thin films were selectively fabricated on Si wafer by 157 nm F₂ laser in N₂/O₂ gas atmosphere. The F₂ laser photochemically produced active O(¹D) atoms from O₂ molecules in the gas atmosphere; strong oxidation reaction could be induced to fabricate SiO₂ thin films only on the irradiated areas of Si wafer. The oxidation reaction was sensitive to the single pulse fluence of F₂ laser. The irradiated areas were swelled and the height was approximately 500-1000 nm at the 205-mJ/cm² single pulse fluence for 60 min laser irradiation. The fabricated thin films were analytically identified to be SiO₂ by the Fourier-transform IR spectroscopy. The SiO₂ thin films could be also removed by subsequent chemical etching to fabricate micro-holes 50 nm in depth on Si wafer for microfabrication.     

Analysis of intensities of positive and negative ion species from silicon dioxide films using time-of-flight secondary ion mass spectrometry and electronegativity of fragments

Intensities of positive and negative ion species emitted from thermally oxidized and plasma-enhanced chemical vapor deposited (PECVD) SiO₂ films were analyzed using time-of-flight secondary ion mass spectrometry (TOF-SIMS) and the Saha-Boltzmann equation. Intensities of positive and negative secondary ion species were normalized to those of ²⁸Si⁺ and ²⁸Si⁻ ions, respectively, and an effective temperature of approximately (7.2 ± 0.1) × 10³ K of the sputtered region bombarded with pulsed 22 kV Au₃⁺ primary ions was determined. Intensity spectra showed polarity dependence on both n and m values of Si_nO_m fragments, and a slight shift to negative polarity for PECVD SiO₂ compared to thermally oxidized SiO₂ films. By dividing the intensity ratios of negative-to-positive ions for PECVD SiO₂ by those for thermally oxidized SiO₂ films to cancel statistical factors, the difference in absolute electronegativity (half the sum of ionization potential and electron affinity of fragments) between both films was obtained. An increase in electronegativity for SiO_m (m = 1, 2) and Si₂O_m (m = 1-4) fragments for PECVD SiO₂ films compared to thermally oxidized films was obtained to be 0.1-0.2 Pauling units, indicating a more covalent nature of Si-O bonds for PECVD SiO₂ films compared to the thermally oxidized SiO₂ films.     

Low cost fabrication of SiO2 optical waveguides by laser direct writing on Ti-doped Sol-Gel films

A commercial direct laser writing (DLW) system operating at 1070 nm was used to fabricate SiO₂ optical waveguides on silicon wafers. A Ti-doped SiO₂ Sol-Gel film was deposited on the SiO₂/Si substrate by the dip-coating technique, based on which SiO₂ optical waveguides were patterned by DLW using a Ytterbium fiber laser and followed by chemical etching. The effects of laser parameters and the preheated temperature of Sol-Gel films on the dimensions of optical waveguides were studied systematically. The differences of etching rate between laser irradiated and non-irradiated areas in Sol-Gel films preheated at various temperatures are characterized by measuring the thickness of the films. Results demonstrate that the available laser power density range for laser densification and the width of the patterned optical waveguides are influenced strongly by the preheated temperature of the Sol-Gel films. The width of the optimized optical waveguide in this work is 25 μm. The minimum propagation loss of the fabricated optical waveguides is 1.7 dB cm⁻¹ at the wavelength of 1550 nm.     

Effects of UV photon irradiation on SiOx (0 < x < 2) structural properties

Thin films of a-SiO_x (0 < x < 2) were prepared by reactive r.f. magnetron sputtering from a polycrystalline-silicon target in an Ar/O₂ gas mixture. The oxygen partial pressure in the deposition chamber was varied so as to obtain films with different values of x. The plasma was monitored, during depositions, by optical emission spectroscopy (OES) system. Energy dispersive X-ray (EDX) measurements and infra-red (IR) spectroscopy were used to study the compositional and structural properties of the deposited layers.Structural modifications of SiO_x thin films have been induced by UV photons’ bombardment (wavelength of 248 nm) using a pulsed laser. IR spectroscopy and X-ray photoemission spectroscopy (XPS) were used to investigate the structural changes as a function of x value and incident energy. SiO_x phase separation by spinodal decomposition was revealed. The IR peak position shifted towards high wavenumber values when the laser energy is increased. Values corresponding to the SiO₂ material (only Si⁴⁺) have been found for laser irradiated samples, independently on the original x value. The phase separation process has a threshold energy that is in agreement with theoretical values calculated for the dissociation energy of the investigated material.For high values of the laser energy, crystalline silicon embedded in oxygen-rich silicon oxide was revealed by Raman spectroscopy.     

Surface chemical states of barium zirconate titanate thin films prepared by chemical solution deposition

Ba(Zr_0.05Ti_0.95)O₃ (BZT) thin films grown on Pt/Ti/SiO₂/Si(1 0 0) substrates were prepared by chemical solution deposition. The structural and surface morphology of BZT thin films has been studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). The results showed that the random oriented BZT thin film grown on Pt/Ti/SiO₂/Si(1 0 0) substrate with a perovskite phase. The SEM surface image showed that the BZT thin film was crack-free. And the average grain size and thickness of the BZT film are 35 and 400 nm, respectively. Furthermore, the chemical states and chemical composition of the films were determined by X-ray photoelectron spectroscopy (XPS) near the surface. The XPS results show that Ba, Ti, and Zr exist mainly in the forms of BZT perovskite structure.     

Laser synthesis of semiconductor nanostructures with narrow band gap

Semiconductor nanostructures with narrow band gap were synthesized by means of laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors [Fe(CO)₅] under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface. The temperature dependence of the specific conductivity of these nanostructures in the form of thin films demonstrated typical semiconductor tendency and gave the possibility to calculate the band gap for intrinsic conductivity (E_g) and the band gap assigned for impurities (E_i), which were depended upon film thickness and applied electrical field. Analysis of deposited films with scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated their cluster structure with average size not more than 100 nm. Semiconductor properties of deposited nanostructures were stipulated with iron oxides in different oxidized phases according to X-ray photoelectron spectroscopy (XPS) analysis.These deposited nanostructures were irradiated with Q-switched YAG laser (λ_L = 1064 nm) at power density about 6 × 10⁷ W/cm². This irradiation resulted in the crystallization process of deposited films on the Si substrate surface. The crystallization process resulted in the synthesis of iron carbide-silicide (FeSi_2−xC_x) layer with semiconductor properties too. The width of the band gap E_g of the synthesized layer of iron carbide-silicide was less than for deposited films based on iron oxides Fe₂O_3−x (0 ≤ x ≤ 1).     

Infrared optical properties of Ba(Zr0.20Ti0.80)O3 and Ba(Zr0.30Ti0.70)O3 thin films prepared by sol-gel method

Ba(Zr_xTi_1−x)O₃ (BZT) (x = 0.20 and 0.30) thin films are deposited on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrate by sol-gel method. X-ray diffraction patterns show that the thin films have a good crystallinity. Optical properties of the films in the wavelength range of 2.5-12 μm are studied by infrared spectroscopic ellipsometry (IRSE). The optical constants of the BZT thin films are determined by fitting the IRSE data using a classical dispersion formula. As the wavelength increases, the refractive index decreases, while the extinction coefficients increase. The effective static ionic charges are derived, which are smaller than that in a purely ionic material for the BZT thin films.     

Doped thin metal oxide films for catalytic gas sensors

TiO₂ and Pt doped TiO₂ thin films were grown by pulsed laser deposition on 〈0 0 1〉 SiO₂ substrates. The doped films were compared with undoped ones deposited in similar experimental conditions. An UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser was used for the irradiation of the TiO₂ or Pt doped TiO₂ targets. The substrate temperatures were fixed during the growth of the thin films at values within the 300-500 °C range. The films’ surface morphology was investigated by atomic force microscopy and their crystalline quality by X-ray diffractometry. The corresponding transmission spectra were recorded with the aid of a double beam spectrophotometer in the spectral range of 400-1100 nm. No contaminants or Pt segregation were detected in the synthesized anatase phase TiO₂ thin films composition. Titania crystallites growth inhibition was observed with the increase of the dopant concentration. The average optical transmittance in the visible-infrared spectral range of the films is higher than 85%, which makes them suitable for sensor applications.