Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba0.7Sr0.3Tio3) thin films

Ferroelectric barium strontium titanate (Ba_0.7Sr_0.3TiO₃)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂]_, strontium 2-ethylhexanoate [Sr[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂] and titanium(IV) isopropoxide [TiOCH(CH₃)₂]₄ precursors using a modified sol-gel technique. The precursor except [TiOCH(CH₃)₂]₄ were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 °C for 1 h in air. The lattice constants “a” and “c” were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 °C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency (∼95%), which decreases slightly after crystallization (∼90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.     

Spray-pyrolysis deposition of LaMnO3 and La1−xCaxMnO3 thin films

Ethylene glycol solutions of La-Mn(II) and La-Ca-Mn(II) citric complexes has been used as a starting material for spray-pyrolysis deposition of LaMnO₃ and La_1−xCa_xMnO₃ thin films on β-quartz, fused quartz, Si(0 0 1) and SrTiO₃(1 0 0) substrates heated during the deposition at 380 °C. At suitable post-deposition heating conditions highly uniform films, 0.1-1 μm in thickness, with good crystal structure were obtained. Highly textured LaMnO₃ films are obtained on SrTiO₃(1 0 0) substrate. Interaction between the layer and Si-containing substrates is observed during the post-deposition heating in static air.     

AlCl3-induced crystallization of amorphous silicon thin films

It is reported that the direct contact between Al and amorphous silicon (a-Si) enhances the crystallization of a-Si films. But the polycrystalline silicon (poly-Si) films crystallized by the direct contact of Al metal film suffer the problems of rough surface. In our study, we utilized the AlCl₃ vapor during the a-Si films deposition instead of Al metal film to enhance crystallization. X-ray diffraction (XRD) shows that the AlCl₃ vapor so successfully enhanced the crystallization of a-Si films that the crystallization was completed in 5 h at 540 °C. And the orientation of the poly-Si film deposited with AlCl₃ vapor is much more random than that of annealed with Al metal under layer. But the average grain size is much larger than that. Moreover, the surface of the AlCl₃-induced crystallized poly-Si film was much smoother than that of the Al-induced poly-Si film. The Al and Cl incorporation into the poly-Si film was confirmed using X-ray photoelectron spectroscopy (XPS) and found that the quantity of Al and Cl incorporated into the Si film was below the detection limit of XPS.     

Laser-induced voltage characteristics of Bi2Sr2Co2Oy thin films on LaAlO3 substrates

We report the laser-induced voltage (LIV) effects in c-axis oriented Bi₂Sr₂Co₂O_y thin films grown on (0 0 1) LaAlO₃ substrates with the title angle α of 0°, 3°, 5° and 10° by a simple chemical solution deposition method. A large open-circuit voltage with the sensitivity of 300 mV/mJ is observed for the film on 10° tilting LaAlO₃ under a 308 nm irradiation with the pulse duration of 25 ns. When the film surface is irradiated by a 355 nm pulsed laser of 25 ps duration, a fast response with the rise time of 700 ps and the full width at half maximum of 1.5 ns is achieved. In addition, the experimental results reveal that the amplitude of the voltage signal is approximately proportional to sin 2α and the signal polarity is reversed when the film is irradiated from the substrate side rather than the film side, which suggests the LIV effects in Bi₂Sr₂Co₂O_y thin films originate from the anisotropic Seebeck coefficient of this material.     

Solid phase epitaxy of Ge films on CaF2/Si(1 1 1)

At room temperature deposited Ge films (thickness < 3 nm) homogeneously wet CaF₂/Si(1 1 1). The films are crystalline but exhibit granular structure. The grain size decreases with increasing film thickness. The quality of the homogeneous films is improved by annealing up to 200 °C. Ge films break up into islands if higher annealing temperatures are used as demonstrated combining spot profile analysis low energy electron diffraction (SPA-LEED) with auger electron spectroscopy (AES). Annealing up to 600 °C reduces the lateral size of the Ge islands while the surface fraction covered by Ge islands is constant. The CaF₂ film is decomposed if higher annealing temperatures are used. This effect is probably due to the formation of GeF_x complexes which desorb at these temperatures.     

AlF3 film deposited by IAD with end-Hall ion source using SF6 as working gas

A novel and effective process to fabricate high quality fluoride thin films was presented. Aluminum fluoride films deposited by a conventional thermal evaporation with an ion-assisted deposition (IAD) using SF₆ as a working gas at around room temperature were investigated. In this study, the optimal voltage and current, 50 V and 0.25 A, were found according to the optical properties of the films: high refractive index (1.489 at 193 nm), low optical absorption and extinction coefficient (<10⁻⁴ at 193 nm) in the UV range. The physical properties of the film are high packing density and amorphous without columnar structure. It was proved that using SF₆ working gas in IAD process is a good choice and significantly improves the quality of AlF₃ films.     

The influence of substrate temperature variation on tungsten oxide thin film growth in an HFCVD system

Tungsten oxide (WO₃) thin films were deposited by a modified hot filament chemical vapor deposition (HFCVD) technique using Si (1 0 0) substrates. The substrate temperature was varied from room temperature to 430 °C at an interval of 100 °C. The influence of the substrate temperature on the structural and optical properties of the WO₃ films was studied. X-ray diffraction and Raman spectra show that as substrate temperature increases the film tends to crystallize from the amorphous state and the surface roughness decreases sharply after 230 °C as confirmed from AFM image analysis. Also from the X-ray analysis it is evident that the substrate orientation plays a key role in growth. There is a sharp peak for samples on Si substrate due to texturing. The film thickness also decreases as substrate temperature increases. UV-vis spectra show that as substrate temperature increases the film property changes from metallic to insulating behavior due to changing stoichiometry, which was confirmed by XPS analysis.     

Structural and optical properties of a-Si1−xCx:H films synthesized by dc magnetron sputtering technique

Hydrogenated amorphous SiC films (a-Si_1−xC_x:H) were prepared by dc magnetron sputtering technique on p-type Si(1 0 0) and corning 9075 substrates at low temperature, by using 32 sprigs of silicon carbide (6H-SiC). The deposited a-Si_1−xC_x:H film was realized under a mixture of argon and hydrogen gases. The a-Si_1−xC_x:H films have been investigated by scanning electronic microscopy equipped with an EDS system (SEM-EDS), X-ray diffraction (XRD), secondary ions mass spectrometry (SIMS), Fourier transform infrared spectroscopy (FTIR), UV-vis-IR spectrophotometry, and photoluminescence (PL). XRD results showed that the deposited film was amorphous with a structure as a-Si_0.80C_0.20:H corresponding to 20 at.% carbon. The photoluminescence response of the samples was observed in the visible range at room temperature with two peaks centred at 463 nm (2.68 eV) and 542 nm (2.29 eV). In addition, the dependence of photoluminescence behaviour on film thickness for a certain carbon composition in hydrogenated amorphous SiC films (a-Si_1−xC_x:H) has been investigated.     

The influence of substrate on the properties of Er2O3 films grown by magnetron sputtering

The structural properties and the room temperature luminescence of Er₂O₃ thin films deposited by RF magnetron sputtering have been studied. Films characterized by good morphological properties have been obtained by using a SiO₂ interlayer between the film and the Si substrate. The evolution of the properties of the Er₂O₃ films due to rapid thermal annealing processes in O₂ ambient performed at temperatures in the range 800-1200 °C has been investigated in details. The existence of well-defined annealing conditions (temperature of 1100 °C or higher) allowing to avoid the occurrence of extensive chemical reactions with the oxidized substrate has been demonstrated and an increase of the photoluminescence (PL) intensity by about a factor of 40 with respect to the as deposited material has been observed. The enhanced efficiency of the photon emission process has been correlated with the longer lifetime of the PL signal. The same annealing processes are less effective when Er₂O₃ is deposited on Si. In this latter case interfacial reactions and pit formation occur, leading to a material characterized by stronger non-radiative phenomena that limit the PL efficiency.     

Characteristics of SrBi2Ta2O9 ferroelectric films in an in situ applied low electric field prepared by metalorganic decomposition

SrBi₂Ta₂O₉ (SBT) films were prepared on Pt/TiO₂/SiO₂/Si substrates at 750 °C in oxygen by metalorganic decomposition method. A low electric field was in situ applied during the film crystallization. It was first found that a low electric field and its direction have significant influence on the microstructures and ferroelectric properties of SBT films. Under a positive electric field (assuming that the bottom electrode is electrically grounded), the films show stronger c-axis-preferred orientation than without electric field and under a negative electric field. As a possible origin is proposed that the interface-induced nucleation growth between SBT and Pt coated substrate with application of low electric field plays a key role. Above all, an in situ applied low electric field during the film crystallization is a promising technique controlling film orientation for film preparation by wet chemical method.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

c-Axis orientation control of YBa2Cu3O7−x films grown on inclined-substrate-deposited MgO-buffered metallic substrates

Biaxially textured YBa₂Cu₃O_7−x (YBCO) films were grown on non-textured metal substrates with inclined-substrate-deposited (ISD) MgO as template. The biaxial texture feature of the films was examined by X-ray pole-figure analysis, φ-scan, and 2θ-scan. A tilt angle of 32° of the MgO[001] with respect to the substrate normal was observed. Epitaxial growth of YBCO films with c-axis tilt angle of 32° with respect to the substrate normal was obtained on these substrates with SrTiO₃(STO) as buffer layer. Whereas, by choosing yttria-stabilized ZrO₂ and CeO₂ instead of STO as buffer layer, a c-axis untilted YBCO film was obtained. Higher values of T_c=91 K and J_c=5.5×10⁵ A/cm² were obtained on the c-axis untilted YBCO films with 0.46 μm thickness at 77 K in zero field. Comparative studies revealed a unique role of CeO₂ in controlling the orientation of the YBCO films grown on ISD-MgO buffered metal substrates.     

Stress induced preferred orientation and phase transition for ternary WCxNy thin films

We deposit ternary WC_xN_y thin films on Si (1 0 0) substrates at 500 °C using direct current (DC) reactive magnetron sputtering in a mixture of CH₄/N₂/Ar discharge, and explore the effects of substrate bias (V_b) on the intrinsic stress, preferred orientation and phase transition for the obtained films by virtue of X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and selective area electron diffraction (SAED). We find that with increasing the absolute value of V_b up to 200 V the carbon (x) and nitrogen (y) atom concentrations of WC_xN_y films keep almost constant with the values of 0.75 and 0.25, respectively. The XPS and SAED results, combined with the density-functional theory (DFT) calculations on the electronic structure of WC_0.75N_0.25, show our obtained WC_xN_y films are single-phase of carbonitrides. Furthermore, we find that the compressive stress sharply increases with increasing the absolute value of V_b, which leads to a pronounced change in the preferred orientation and phase structure for the film, in which a phase transition from cubic β-WC_xN_y to hexagonal α-WC_xN_y occurs as V_b is in the range of −40 to −120 V. In order to reveal the relationship between the stress and phase transition as well as preferred orientation, the DFT calculations are used to obtain the elastic constants for β-WC_xN_y and α-WC_xN_y. The calculated results show that the preferred orientation is dependent on the competition between strain energy and surface energy, and the phase transition can be attributed to a decrease in the strain energy.     

Investigation of thin TiO2 films cosputtered with Si species

Titanium dioxide (TiO₂) films were fabricated by cosputtering titanium (Ti) target and SiO₂ or Si slice with ion-beam-sputtering deposition (IBSD) technique and were postannealed at 450 °C for 6 h. The variations of oxygen bonding, which included high-binding-energy oxygen (HBO), bridging oxygen (BO), low-binding-energy oxygen (LBO), and three chemical states of titanium (Ti⁴⁺, Ti³⁺ and Ti²⁺) were analyzed by X-ray photoelectron spectroscopy (XPS). The enhancement of HBO and reduction of BO in O 1s spectra as functions of SiO₂ or Si amount in cosputtered film imply the formation of Si-O-Ti linkage. Corresponding increase of Ti³⁺ in Ti 2p spectra further confirmed the property modification of the cosputtered film resulting from the variation of the chemical bonding. An observed correlation between the chemical structure and optical properties, refractive index and extinction coefficient, of the SiO₂ or Si cosputtered films demonstrated that the change of chemical bonding in the film results in the modification of optical properties. Furthermore, it was found that the optical properties of the cosputtered films were strongly depended on the cosputtering targets. In case of the Si cosputtered films both the refractive indices and extinction coefficients were reduced after postannealing, however, the opposite trend was observed in SiO₂ cosputtered films.     

Structural and surface properties of Si1−xGex thin films obtained by reduced pressure CVD

This paper investigates the structure and surface characteristics, and electrical properties of the polycrystalline silicon-germanium (poly-Si_1−xGe_x) alloy thin films, deposited by vertical reduced pressure CVD (RPCVD) in the temperature range between 500 and 750 °C and a total pressure of 5 or 10 Torr. The samples exhibited a very uniform good quality films formation, with smooth surface with rms roughness as low as 7 nm for all temperature range, Ge mole fraction up to 32% (at 600 °C), textures of 〈2 2 0〉 preferred orientation at lower temperatures and strong 〈1 1 1〉 at 750 °C, for both 5 and 10 Torr deposition pressures. The ³¹P⁺ and ¹¹B⁺ doped poly-Si_1−xGe_x films exhibited always lower electrical resistivity values in comparison to similar poly-Si films, regardless of the employed anneal temperature or implantat dose. The results indicated also that poly-Si_1−xGe_x films require much lower temperature and ion implant dose than poly-Si to achieve the same film resistivity. These characteristics indicate a high quality of obtained poly-Si_1−xGe_x films, suitable as a gate electrode material for submicron CMOS devices.     

Atomic layer deposition of PbZrO3 thin films

In this paper, we report on the preparation of lead zirconate films for the first time using atomic layer deposition in an attempt to investigate some of the film properties and also to evaluate possible use of the precursor combination to prepare more complex lead titanate zirconate. In the depositions tetraphenyl lead (Ph₄Pb) was used as the lead and zirconium 2,2,6,6-tetramethyl-3,5-heptadionato (Zr(thd)₄) as the zirconium precursor, while ozone was used as the oxygen source. Film growth, stoichiometry and quality were studied using different pulsing ratios at deposition temperatures of 275 and 300 °C. According to X-ray diffraction, the crystalline perovskite phase was observed when films deposited on SrTiO₃(1 0 0) were annealed at 600 °C. Surface roughness was reduced for lead deficient films as well as in annealed samples.     

Structural and optical characterization of Ce-doped Gd2SiO5 films by sol-gel technique

Cerium-doped Gd₂SiO₅ (GSO:Ce) films have been prepared on (1 1 1) silicon substrates by the sol-gel technique. Annealing was performed in the temperature range from 400 to 1000 °C. X-ray diffraction (XRD), and atomic force microscopy (AFM) were used to investigate the structure and morphology of GSO:Ce films. Results showed that GSO:Ce film starts to crystallize at about 600 °C, GSO:Ce films have a preferential (0 2 1) orientation, as the annealing temperature increase, the (0 2 1) peak intensity increases, the full width of half maximum (FWHM) decreases, and the grain size of GSO:Ce films increases. Emission spectra of GSO:Ce films were measured, results exhibit the characteristic blue emission peak at 427 nm.     

Epitaxial growth and structural characterization of Pb(Fe1/2Nb1/2)O3 thin films

We have grown lead iron niobate thin films with composition Pb(Fe_1/2Nb_1/2)O₃ (PFN) on (0 0 1) SrTiO₃ substrates by pulsed laser deposition. The influence of the deposition conditions on the phase purity was studied. Due to similar thermodynamic stability spaces, a pyrochlore phase often coexists with the PFN perovskite phase. By optimizing the kinetic parameters, we succeeded in identifying a deposition window which resulted in epitaxial perovskite-phase PFN thin films with no identifiable trace of impurity phases appearing in the X-ray diffractograms. PFN films having thicknesses between 20 and 200 nm were smooth and epitaxially oriented with the substrate and as demonstrated by RHEED streaks which were aligned with the substrate axes. X-ray diffraction showed that the films were completely c-axis oriented and of excellent crystalline quality with low mosaicity (X-ray rocking curve FWHM?0.09°). The surface roughness of thin films was also investigated by atomic force microscopy. The root-mean-square roughness varies between 0.9 nm for 50-nm-thick films to 16 nm for 100-nm-thick films. We also observe a correlation between grain size, surface roughness and film thickness.     

Helical nanostructures of SiOx synthesized through the heating of Co-coated substrates

This paper presents the use of the simple annealing technique at 1000 °C to produce the helical nanostructures of SiO_x. We have employed the Co-coated Si substrates, with Co layer and Si substrate utilized as catalyst and Si source, respectively. Beside the ordinary straight nanowires, the helical nanowires such as nanosprings and nanorings were observed. The product was an amorphous structure of SiO_x. We have discussed the possible growth mechanism. Photoluminescence spectrum of the SiO_x nanostructures showed a blue emission at 428 nm and a green emission at 534 nm, respectively.     

A combinatorial approach to the discovery and optimization of YCa4O(BO3)3-based luminescent materials

Thin films of YCa₄O(BO₃)₃ (YCOB)-based new luminescent materials were explored by the combinatorial pulsed laser deposition (PLD) method which enabled us to fabricate continuous composition spread film libraries. Strong red and green luminescence were found in the Y_1−xEu_xCOB (0 ≤ x ≤ 1), (YEuCOB) and Y_1−yTb_yCOB (0 ≤ y ≤ 1) (YTbCOB) films, respectively. The film libraries were characterized by photoluminescence (PL), PL decay, an electron-probe microanalyzer and an electron diffraction analysis. The luminescent intensities in the amorphous film libraries strongly depended on the chemical composition of each rare-earth (RE) ion. The optimum concentration of rare-earth ions in YEuCOB and YTbCOB were experimentally determined to be Eu = 7.5% and Tb = 20-30%, respectively.