Surface chemical modification of TEOS based silica aerogels synthesized by two step (acid-base) sol-gel process

The present paper describes the comparative studies on the hydrophobic and physical properties of the tetraethoxysilane (TEOS) based silica aerogels prepared by two step sol-gel process followed by supercritical drying. Silica alcogels were prepared by keeping the molar ratio of TEOS:methanol (MeOH):H₂O (acidic):H₂O (basic) constant at 1:33:3.5:3.5 with oxalic acid and ammonium hydroxide concentrations fixed at 0.001 and 1 M, respectively. In all, nine different co-precursors (CP) of the type R_nSiX_4 − n, have been used. The aerogels have been characterized by density, porosity, percentage of volume shrinkage, optical transmission, contact angle and thermal conductivity measurements. The surface chemical modification of silica aerogels was confirmed by the presence of CH and SiC peaks at 2900, 1450 and 840 cm⁻¹, respectively, from the Fourier transform-infrared spectroscopy (FT-IR). The microstructure of the aerogels was studied using transmission electron microscopy (TEM) and scanning electron microscopy (SEM) techniques. In addition to these studies, the stability of the hydrophobic aerogels against an organic impurity (methanol, in the present studies) in water has also been studied.     

Fabrication of hydrophobic alumina aerogel monoliths by surface modification and ambient pressure drying

Hydrophobic crack-free alumina aerogel monoliths were fabricated by -Si(CH₃)₃ (trimethylsilyl substituent) modification of alcogels followed by an ambient pressure drying procedure. One-step solvent exchange and surface modification were simultaneously progressed by immersing alumina alcogels in trimethylmethoxysilane (TMMOS)/hexane solution. It is found that the hydrophobic property of alumina aerogels is affected by the contents of TMMOS from the measurements of contact angle and Fourier transform infrared spectrometry. Thermogravimetry/differential scanning calorimetry analyses reveal that the modified aerogels maintain their hydrophobic behavior up to a temperature of 260 °C. The structure and morphology of the obtained hydrophobic alumina aerogels were characterized by the measurements of N₂ physical adsorption and scanning electron microscopy, which showed that they were highly porous materials with narrow slit-like pore geometry and a high degree of pore size uniformity.     

Rapid synthesis of water-glass based aerogels by in situ surface modification of the hydrogels

The objective of the present research was to reduce the processing time of water-glass based aerogels synthesized via an ambient pressure drying. For this purpose we employed a co-precursor method for the surface modification in hydrogels using trimethylchlorosilane (TMCS) and hexamethyldisilazane (HMDS). The surface modification resulted in the displacement of pore water from the hydrogels and thereby absolutely avoiding the time-consuming solvent exchange step. The attachment of trymethylsilyl (Si(CH₃)₃) groups to the silica surface was confirmed by the presence of SiCH₃ peaks at 2900, 1400, 1255 and 845 cm⁻¹ in the Fourier Transform Infrared (FTIR) spectra. The differential thermal analysis (DTA) revealed that the aerogels maintain their hydrophobic behavior up to a maximum temperature of 500 °C above which they become hydrophilic. The physical and textural properties of the silica aerogels have been reported and the results have been discussed by taking into account the surface modification and the amounts of the pore water displaced out from the hydrogels.     

Organic modification of TEOS based silica aerogels using hexadecyltrimethoxysilane as a hydrophobic reagent

The experimental results on the synthesis and characterization of tetraethoxysilane (TEOS) based hydrophobic silica aerogels using hexadecyltrimethoxysilane (HDTMS) as a hydrophobic reagent by two step sol-gel process, are described. The molar ratio of tetraethoxysilane (TEOS), methanol (MeOH), acidic water (0.001 M, oxalic acid) and basic water (10 M, NH₄OH) was kept constant at 1:55:3.25:1.25 and the molar ratio of HDTMS/TEOS (M) was varied from 0 to 28.5 × 10⁻². The organic modification was confirmed by infrared spectroscopic studies, and the hydrophobicity of the aerogels was tested by the contact angle measurements. The maximum contact angle of 152° was obtained for M = 22.8 × 10⁻². The aerogels retained the hydrophobicity up to a temperature of 240 °C and above this temperature the aerogels became hydrophilic. The aerogels were characterized by the thermal conductivity, density, contact angle measurements, optical transmission and scanning electron micrographs.     

Cationic starch as a precursor to prepare porous activated carbon for application in supercapacitor electrodes

Three activated carbons (ACs) for the electrodes of supercapacitor were prepared from cationic starch using KOH, ZnCl₂ and ZnCl₂/CO₂ activation. The BET surface area, pore volume and pore size distribution of the ACs were evaluated using density functional theory method, based on N₂ adsorption isotherms at 77 K. The surface morphology was characterized with SEM. Their electrochemical performance in prototype capacitors was determined by galvanostatic charge/discharge characteristics and cyclic voltammetry, and compared with that of a commercial AC, which was especially prepared for use in supercapacitors. The KOH-activated starch AC presented higher BET surface area (3332 m² g⁻¹) and larger pore volume (1.585 cm³ g⁻¹) than those of the others, and had a different surface morphology. When used for the electrodes of supercapacitors, it exhibited excellent capacitance characteristics in 30 wt% KOH aqueous electrolytes and showed a high specific capacitance of 238 F g⁻¹ at 370 mA g⁻¹, which was nearly twice that of the commercial AC.     

Magnetic hydrophobic nanocomposites: Silica aerogel/maghemite

Magnetic hydrophobic aerogels (MHA) in the form of nanocomposites of silica and maghemite (γ-Fe₂O₃) were prepared by one step sol–gel procedure followed by supercritical solvent extraction. Silica alcogels were obtained from TEOS, MTMS, methanol and H₂O, and Fe(III) nitrate as magnetic precursor. The hydrophobic property was achieved using the methytrimethoxysilane (MTMS) as co-precursor for surface modification. The so produced nanocomposite aerogels are monolithic, hydrophobic and magnetic. The interconnected porous structure hosts ∼6 nm size γ-Fe₂O₃ particles, has a mean pore diameter of 5 nm, and a specific surface area (SSA) of 698 m²/g. Medium range structure of MHA is determined by SAXS, which displays the typical fractal power law behavior with primary particle radius of ∼1 nm. Magnetic properties of the nanoparticle ensembles hosted in them are studied by means of dc-magnetometry.     

Preparation and characterization of carbons for the retention of halogens in the condenser vacuum system of a thermonuclear plant

Activated carbons were prepared by air and carbon dioxide activation, from almond tree pruning, with the aim of obtaining carbons that reproduce the textural and mechanical properties of the carbons currently used in the filtering system of the condenser vacuum installation of a Thermonuclear Plant (CNA; Central Nuclear de Almaraz in Caceres, Spain), produced from coconut shell. The variables studied in non-catalytic gasification series with air were the temperature (215-270 °C) and the time (1-16 h) and the influence of the addition of one catalyst (Co) and the time (1-2 h) in catalytic gasification. In the case of activation with CO₂, the influence of the temperature (700-950 °C) and the time (1-8 h) was studied. The resulting carbons were characterized in terms of their BET surface, porosity, and pore size distribution. The N₂ adsorption isotherms at 77 K for both series showed a type I behaviour, typical of microporous materials. The isotherms showed that with both gasificant agents the temperature rise produced an increase in the carbon porosity. With regards to the activation time, a positive effect on the N₂ adsorbed volume on the carbons was observed. The best carbons of each series, as well as the CNA (carbon currently used in the CNA), were characterized by mercury porosimetry and iodine solution adsorption isotherms. The results obtained allowed to state that several of the carbons produced had characteristics similar to the carbon that is target of reproduction (which has S_BET of 741 m² g⁻¹, V_mi of 0.39 cm³ g⁻¹ and a iodine retention capacity of 429.3 mg g⁻¹): carbon C (gasification with CO₂ at 850 °C during 1 h), with S_BET of 523 m² g⁻¹, V_mi of 0.33 cm³ g⁻¹ and a iodine retention capacity of 402.5 mg g⁻¹, and carbon D (gasification with CO₂ at 900 °C during 1 h), whose S_BET is 672 m² g⁻¹, V_mi is 0.28 cm³ g⁻¹ and has a iodine retention capacity of 345.2 mg g⁻¹.     

Fabrication and application of highly ordered mesoporous Co3O4, NiO, and their metals

Highly ordered mesoporous Co₃O₄, NiO, and their metals were synthesized by nanocasting method using there corresponding mesoporous SBA-15 silica as a template. The obtained porous metal oxides have high surface areas, large pore volume, and a narrow pore size distribution. The N₂-adsorption data for mesoporous metal oxides have provided the BET area of 257.7 m² g⁻¹ and the total pore volume of 0.46 cm³ g⁻¹. The mesoporous metals were employed as a catalyst in the synthesis of (S)-3-pyrrolidinol from chiral (S)-4-chloro-3-hydroxybutyronitrile, and a high yield to (S)-3-pyrrolidinol-salt was obtained on the mesoporous Co metal catalyst.     

Direct synthesis of mesoporous carbon from the carbonization of hydroxypropyl-β-cyclodextrin/silica composite and its catalytic performance

A simple and efficient route is reported for the synthesis of mesoporous carbon materials by directly carbonizing hydroxypropyl-β-cyclodextrin-silica composites. The resulting carbon materials, with uniform wormlike mesoporous structure and certain degree graphitic phase characteristics in porous wall, possess narrow pore size distribution, high surface area (>1000 m² g⁻¹) and pore volume (>1.2 cm³ g⁻¹). It is worth mentioning that the carbon materials have high catalytic activity for the reduction of p-nitrotoluene using hydrazine hydrate as the reducing agent; moreover, the catalytic activity is not reduced notably after being reused for six times.     

Single crystal EPR and optical absorption study of Cr doped l-histidine hydrochloride monohydrate

EPR study of the Cr³⁺ ion doped l-histidine hydrochloride monohydrate single crystal is done at room temperature. Two magnetically inequivalent interstitial sites are observed. The hyperfine structure for Cr⁵³ isotope is also obtained. The zero field and spin Hamiltonian parameters are evaluated from the resonance lines obtained at different angular rotations and the parameters are: D=(300±2)×10⁻⁴ cm⁻¹, E=(96±2)×10⁻⁴ cm⁻¹, g_x=1.9108±0.0002, g_y=1.9791±0.0002, g_z=2.0389±0.0002, A_x=(252±2)×10⁻⁴ cm⁻¹, A_y=(254±2)×10⁻⁴ cm⁻¹, A_z=(304±2)×10⁻⁴ cm⁻¹ for site I and D=(300±2)×10⁻⁴ cm⁻¹, E=(96±2)×10⁻⁴ cm⁻¹, g_x=1.8543±0.0002, g_y=1.9897±0.0002, g_z=2.0793±0.0002, A_x=(251±2)×10⁻⁴ cm⁻¹, A_y=(257±2)×10⁻⁴ cm⁻¹, A_z=(309±2)×10⁻⁴ cm⁻¹ for site II, respectively. The optical absorption studies of single crystals are also carried out at room temperature in the wavelength range 195-925 nm. Using EPR and optical data, different bonding parameters are calculated and the nature of bonding in the crystal is discussed. The values of Racah parameters (B and C), crystal field parameter (Dq) and nephelauxetic parameters (h and k) are: B=636, C=3123, Dq=2039 cm⁻¹, h=1.46 and k=0.21, respectively.     

High surface area thermally stabilized porous iron oxide/silica nanocomposites via a formamide modified sol-gel process

Iron oxide/silica (Fe:Si as 1:10 atomic ratio) composite materials have been prepared by calcination for 3 h at different temperatures (400-900 °C) of xerogel precursor obtained via a formamide modified sol-gel process. The process involved TEOS and iron(III) nitrate, nitric acid and formamide. Genesis of the composite materials from the xerogel precursor has been investigated by TGA, DSC, FTIR, XRD, SEM and EDX. Results indicated that all the calcined composites are mainly composed of amorphous iron oxide dispersed as finely divided particles in amorphous silica matrixes. Nitrogen adsorption/desorption isotherms revealed a reversible type I of isotherms indicative of microporosity. However, high S_BET surface area and microsporosity were observed for the calcined composite materials (e.g. S_BET = 625 m² g⁻¹, and S_αs = 556 m² g⁻¹ for the composite calcined at 400 °C). Formation of the porous texture was discussed in terms of the action of formamide, which enhanced strengthening of the silica gel network during evaporation of the more volatile components within the composite body during the drying process.     

Comparative study of electrochemical capacitance of multi-walled carbon nanotubes before and after chopping

In the work, short multi-walled carbon nanotubes (S-CNTs) were synthesized by chopping conventional μm-long multi-walled carbon nanotubes (L-CNTs) under ultrasonication in H₂SO₄/HNO₃ mixed acids. A comparative electrochemical investigation performed in 6 M KOH solution demonstrated that a specific capacitance (SC) of ca. 14.6 μF cm⁻² was delivered by the S-CNTs with the specific surface area (SSA) of 207 m² g⁻¹, much larger than that of ca. 10.1 μF cm⁻² for the L-CNTs with the SSA of 223 m² g⁻¹, the reason for which was that S-CNTs with two open ends, due to good ion penetrability, provided more entrances for electrolyte ions to access the inner surface easily through their shorter inner pathway so as to enhance their SSA utilization and geometric SC. The surface structure disruption of S-CNTs, owing to ultrasonication and oxidation during chopping process, deteriorated their electronic conductivity and resulted in an inferior power property in contrast to L-CNTs.     

Structural and electrical transport properties of ZnxFe3−xO4 thin film deposited on Si (1 1 1) by pulsed-laser deposition

Polycrystalline thin films of Fe_3−xZn_xO₄ (x = 0.0, 0.01 and 0.02) were prepared by pulsed-laser deposition technique on Si (1 1 1) substrate. X-ray diffraction studies of parent as well as Zn doped magnetite show the spinel cubic structure of film with (1 1 1) orientation. The order–disorder transition temperature for Fe₃O₄ thin film with thickness of 150 nm are at 123 K (Si). Zn doping leads to enhancement of resistivity by Zn²⁺ substitution originates from a decrease of the carrier concentration, which do not show the Verwey transition. The Raman spectra for parent Fe₃O₄ on Si (1 1 1) substrate shows all Raman active modes for thin films at energies of T_2g¹, T_2g³, T_2g², and A_1g at 193, 304, 531 and 668 cm⁻¹. It is noticed that the frequency positions of the strongest A_1g mode are at 668.3 cm⁻¹, for all parent Fe₃O₄ thin film shifted at lower wave number as 663.7 for Fe_2.98Zn_0.02O₄ thin film on Si (1 1 1) substrate. The integral intensity at 668 cm⁻¹ increased significantly with decreasing doping concentration and highest for the parent sample, which is due to residual stress stored in the surface.     

Preparation of activated carbons from cherry stones by activation with potassium hydroxide

Using cherry stones, the preparation of activated carbon has been undertaken in the present study by chemical activation with potassium hydroxide. A series of KOH-activated products was prepared by varying the carbonisation temperature in the 400-900 °C range. Such products were characterised texturally by gas adsorption (N₂, −196 °C), mercury porosimetry, and helium and mercury density measurements. FT-IR spectroscopy was also applied. The carbons prepared as a rule are microporous and macroporous solids. The degree of development of surface area and porosity increases with increasing carbonisation temperature. For the carbon heated at 900 °C the specific surface area (BET) is 1624 m² g⁻¹, the micropore volume is 0.67 cm³ g⁻¹, the mesopore volume is 0.28 cm³ g⁻¹, and the macropore volume is 1.84 cm³ g⁻¹.     

Preparation and characterization of activated carbon produced from pomegranate seeds by ZnCl2 activation

In this study, pomegranate seeds, a by-product of fruit juice industry, were used as precursor for the preparation of activated carbon by chemical activation with ZnCl₂. The influence of process variables such as the carbonization temperature and the impregnation ratio on textural and chemical-surface properties of the activated carbons was studied. When using the 2.0 impregnation ratio at the carbonization temperature of 600 °C, the specific surface area of the resultant carbon is as high as 978.8 m² g⁻¹. The results showed that the surface area and total pore volume of the activated carbons at the lowest impregnation ratio and the carbonization temperature were achieved as high as 709.4 m² g⁻¹ and 0.329 cm³ g⁻¹. The surface area was strongly influenced by the impregnation ratio of activation reagent and the subsequent carbonization temperature.     

Hydrophobic and physical properties of the ambient pressure dried silica aerogels with sodium silicate precursor using various surface modification agents

The experimental results on the synthesis and physical properties of the ambient pressure dried hydrophobic silica aerogels in the presence of various surface modification (silylating) agents are presented. The silica aerogels were prepared with 1.12 specific gravity ion exchanged sodium silicate solution, 1N ammonium hydroxide, solvent exchanged with ethanol and hexane, and surface modification with 20% silylating agent in hexane followed by drying the modified gel up to 200 °C. The molar ratio of sodium silicate, water, ammonium hydroxide and silylating agent was kept at 1:45:4.3 × 10⁻²:5, respectively. The physical properties of the aerogels such as density, % of porosity, pore volume, thermal conductivity and contact angle measurements were studied by using various mono, di and tri alkyl or aryl silylating agents (SAs). The tri alkyl silylating agents produced low % of volume shrinkage (2%), low density (0.06 g/cm³), low refractive index (1.011), more pore volume (16.15cm³/g), high percentage of porosity (96.9%) and hydrophobic (contact angle >150°) silica aerogels. It was found from the Fourier transform infrared spectroscopic (FTIR) studies of the aerogels that the intensity of the bands related to the SiC and CH are more and the SiOH and OH are less with the tri than mono and di alkyl SAs. It was found from the TGA-DTA studies of the aerogels with increase in temperature above 325 °C, the % of weight decrease in TGA and exothermic peak in DTA are more with tri than the mono and di alkyl SAs. The SEM studies of the aerogels showed the large pore and particle sizes in the silica network with the tri alkyl SAs. The % of optical transmission of the aerogels is less with the tri alkyl SAs than the mono and di alkyl SAs. It was found from the contact angle and water adsorption studies that the hydrophobicity of the silica aerogel is more with tri alkyl than the di and mono alkyl silylating agents.     

The size and strain effects on the Raman spectra of Ce1−xNdxO2−δ (0≤x≤0.25) nanopowders

Ultrafine Ce_1−xNd_xO_2−δ (x=0-0.25) powders were synthesized by self-propagating room temperature synthesis. Raman spectra were measured at room temperature in the 300-700 cm⁻¹ spectral range. The shift and asymmetric broadening of the Raman F_2g mode at about 454 cm⁻¹ in pure and doped ceria samples could be explained with combined size and inhomogenous strain effects. Increased concentration of O²⁻ vacancies with doping is followed by an appearance of new Raman feature at about 545 cm⁻¹.     

ESR and optical study of Mn doped potassium hydrogen sulphate

The ESR spectrum of Mn²⁺ doped potassium hydrogen sulphate at liquid nitrogen temperature (77 K) has been analyzed and site of entered Mn²⁺ in the lattice has been discussed. The values of the zero field parameters that give good fit to the observed ESR spectra have been obtained. The obtained g, A, B, D, E and a values are 2.0002, 66×10⁻⁴ cm⁻¹, 26×10⁻⁴ cm⁻¹, 59×10⁻⁴ cm⁻¹, 32×10⁻⁴ cm⁻¹ and −8×10⁻⁴ cm⁻¹, respectively. The percentage of covalency of the metal-ligand bond has also been estimated. From the optical absorption study at room temperature, the distortion has been suggested. The observed bands are assigned as transitions from the ⁶A_1g(S) ground state to various excited quartet levels of Mn²⁺ ion in a cubic crystalline field. The electron repulsion and crystal field parameters B, C, Dq and α providing good fit to the observed optical spectra have been evaluated and the values obtained for the parameters are B=627 cm⁻¹, C=2580 cm⁻¹ , Dq=790 cm⁻¹ and α=76 cm⁻¹.     

ESR of Cu doped cadmium (II) formate dihydrate

Electron spin resonance (ESR) of Cu²⁺ doped cadmium formate dihydrate single crystal was studied at room temperature. Copper enters the lattice substitutionally and is trapped at two magnetically inequivalent sites. The observed spectra are fitted to a spin-Hamiltonian of rhombic symmetry with the following values of the spin-Hamiltonian parameters, Cu²⁺(I): g_x=2.097±0.002, g_y=2.1166±0.002, g_z=2.2887±0.002 and A_x=(140±2)×10⁻⁴ cm⁻¹, A_y=(151±2)×10⁻⁴ cm⁻¹, A_z=(239±2)×10⁻⁴ cm⁻¹, Cu²⁺(II): g_x=2.0843±0.002, g_y=2.1045±0.002, g_z=2.2742±0.002 and A_x=(141±2)×10⁻⁴ cm⁻¹, A_y=(158±2)×10⁻⁴ cm⁻¹, A_z=(267±2)×10⁻⁴ cm⁻¹. The ground state wave function of the Cu²⁺ ion in this lattice is evaluated. It is found that the ground state is predominantly |x²−y²〉. The g-factor anisotropy is also calculated and compared with the experimental value. With the help of the optical absorption study, the nature of bonding in the complex has been discussed.     

Studies of the zero-field splitting and g-factor for the defect model of Cr in α-LiIO3 crystals at low temperature

The EPR zero-field splitting parameters D and g-factors for Cr³⁺ in α-LiIO₃ single crystal, taking into account both the effect of lattice distortion and two Li⁺ vacancies, have been investigated using a complete diagonalization method (CDM) for 3d³ ions in a trigonal symmetry crystal field. The theoretical results (D=−0.60876 cm⁻¹, g_∥=1.9641, g_⊥=1.9682) are in excellent agreement with experimental results (D=−0.6099(3) cm⁻¹g_∥=1.965±0.001, g_⊥=1.971±0.002). In addition, Macfarlane's perturbation expressions lead to results almost identical with the CDM for Cr³⁺ in an α-LiIO₃ single crystal.