Structural, optical and electrical studies on pulse electrodeposited CdIn2S4 thin films

CdIn₂S₄ thin films were prepared by pulse electrodeposition technique over F:SnO₂ glass and stainless steel substrates in galvanostatic mode from an aqueous acidic bath containing CdSO₄, InCl₃ and Na₂S₂O₃. The growth kinetics of the film has been studied and the deposition parameters such as electrolyte bath concentration, bath temperature, time of deposition, deposition current and pH of the bath are optimized. X-ray diffraction (XRD) analysis of the as deposited and annealed films shows polycrystalline nature. Energy dispersive analysis by X-ray (EDAX) confirms nearly stoichiometric CdIn₂S₄ nature of the film. Scanning electron microscope (SEM) studies show that, the deposited films are well adherent and grains are uniformly distributed over the surface of the substrate. The optical transmission spectra show a direct band gap of 2.16 eV. Conductivity measurements have been carried out at different temperatures and electrical parameters such as activation energy, trapped energy state and barrier heights etc. have been determined.     

Structure formation and mechanisms of DC conduction in thermally evaporated nanocrystallite structure ZnIn2Se4 thin films

ZnIn₂Se₄ is of polycrystalline structure in as synthesized condition. It transforms to nanocrystallite structure of ZnIn₂Se₄ film upon thermal evaporation. Annealing temperatures influenced crystallite size, dislocation density and internal strain. The hot probe test showed that ZnIn₂Se₄ thin films are n-type semiconductor. The dark electrical resistivity versus reciprocal temperature for planar structure of Au/ZnIn₂Se₄/Au showed existence of two operating conduction mechanisms depending on temperature. At temperatures >365 K, intrinsic conduction operates with activation energy of 0.837 eV. At temperatures <365 K, extrinsic conduction takes place with activation energy of 0.18 eV. The operating conduction mechanism in extrinsic region is variable range hopping. The parameters such as density of states at Fermi level, hopping distance and average hopping energy have been determined and it was found that they depend on film thickness. The dark current–voltage characteristics of Au/n-ZnIn₂Se₄/p-Si/Al diode at different temperatures ranging from 293–353 K have been investigated. Results showed rectification behavior. At forward bias potential <0.2 V, thermionic emission of electrons from ZnIn₂Se₄ film over a potential barrier of 0.28 V takes place. At forward bias potential >0.2 V, single trap space charge limited current is operating. The trap concentration and trap energy level have been determined as 3.12×10¹⁹ cm⁻³ and 0.24 eV, respectively.     

Structural and optical properties of ZnO thin films on (111) CaF2 substrates grown by magnetron sputtering

ZnO thin films were grown on (111) CaF₂ substrates by magnetron sputtering at room temperature. Structural and optical properties of the ZnO thin films were studied. XRD analysis showed that the ZnO thin films had the (002) preferential orientation. The transmittance of ZnO thin films was over 80% in the visible range. The optical band gap of the ZnO thin films was 3.26 eV. The optical constants (n,k)$(n,k)$ of the ZnO thin films in the wavelength range 300–1000 nm were obtained by infrared spectroscopic ellipsometry measurement. PL spectra of ZnO thin films showed strong UV near-band-edge emission peak at 376.5 nm and weak visible red emission at 643.49 nm using He–Cd laser as the light source, using a synchrotron radiation light source PL spectra showed three emission peak at 320 nm, 410 nm and 542 nm respectively.     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

SrF2-CaF2混合物薄膜的物理及红外光学特性研究

采用热蒸发和电子束蒸发两种沉积方式分别沉积了相同厚度的SrF₂-CaF₂ (比例为1∶1) 的混合物薄膜,对其物理和光学特性进行了研究,并定量地给出了其在红外波段的光学常数,填补了这一数据的空白. 同时提供了一种获得不同低折射率薄膜的方法.文中还以该比例的混合物作为低折射率材料,研制出具有很好的光学性能的长波红外宽光谱增透膜.     

Investigation on properties of TiO2 thin films deposited at different oxygen pressures

TiO₂ thin films were prepared by electron beam evaporation at different oxygen partial pressures. The influences of oxygen partial pressure on optical, mechanical and structural properties of TiO₂ thin films were studied. The results showed that with the increase of oxygen partial pressure, the optical transmittance gradually increased, the transmittance edge gradually shifted to short wavelength, and the corresponding refractive index decreased. The residual stresses of all samples were tensile, and the value increased as oxygen partial pressure increasing, which corresponded to the evolutions of the packing densities. The structures of TiO₂ thin films all were amorphous because deposition particles did not possess enough energy to crystallize.     

Structural characterization and optical properties of UO2 thin films by magnetron sputtering

Uranium dioxide films were deposited on Si (1 1 1) substrates by dc magnetron sputtering method at different sputtering parameters. The structure, morphology and chemical state of the films were studied by field emission scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. Influences of film thickness on the microstructure and optical properties were investigated. Experimental results show that the film crystallites are preferentially oriented with the (1 1 1) planes. The average grain size increases with increasing film thickness. AFM images show that the root mean square roughness of the films is between 1.2 nm and 2.1 nm. Optical constants (refractive index, extinction coefficient) of the films in the wavelength range of 350-1000 nm are obtained by ellipsometric spectroscopy. The result shows that the refractive index decreases with the increasing film thickness, while extinction coefficient increases with the film thickness.     

Photoelectrochemical properties of electrochemically deposited CdIn2S4 thin films

Thin films of CdIn₂S₄ have been deposited on to stainless steel and fluorine-doped tin oxide (FTO)-coated glass substrates from aqueous acidic bath using an electrodeposition technique. Ethylene diamine tetra-acetic acid (EDTA) disodium salt is used as complexing agent to obtain good-quality deposits by controlling the rate of the reaction. The different preparative parameters like concentration of bath, deposition time, bath temperature, pH of the bath have been optimized by the photoelectrochemical (PEC) technique in order to get good-quality photosensitive material. Different techniques have been used to characterize CdIn₂S₄ thin films. Optical absorption shows the presence of direct transition with band gap energy 2.17 eV. The X-ray diffraction (XRD) analysis of the as-deposited and annealed films showed the presence of polycrystalline nature. Energy-dispersive analysis by X-ray (EDAX) study for the sample deposited at optimized preparative parameters shows that the In-to-Cd ratio is almost 2 and S-to-Cd ratio is almost 4. Scanning electron microscopy (SEM) for samples deposited at optimized preparative parameters reveals that spherical grains are uniformly distributed over the surface of the substrate indicates the well-defined growth of polycrystalline CdIn₂S₄ thin film. PEC characterization of the films is carried out by studying photoresponse, spectral response and photovoltaic output characteristics. The fill factor (ff) and power conversion efficiency (η) of the cell are 69 and 2.94%, respectively.     

Synthesis and characterization of immobilized activated carbon doped TiO2 thin films

Immobilized activated carbon doped TiO₂ thin films were prepared by sol–gel dip coating method by using Titanium IV isopropoxide as a precursor. Aim of our work is to synthesize and investigate the structural, surface morphology and optical properties of the synthesized thin film. X-ray diffraction pattern reveals that the crystallinity of the film increases with increase in temperature. Also, the structural parameters such as particle size, microstrain and dislocation density have been calculated. The formation of nanosphere of diameter ranging from 300 nm to 500 nm has been confirmed by Scanning electron microscope. Photocatalytic active large optical band gap at 3.75 eV was found by using UV–visible sspectrum.     

纳米ZnO和ZnO-SiO2复合薄膜的光学性质研究

通过溶胶凝胶(sol-gel)法分别在玻璃衬底上制备了ZnO纳米薄膜和ZnO-SiO₂纳米复合薄膜,并利用紫外-可见光分光光度计对薄膜的光学性能进行了分析.可见光-紫外透射谱显示,随着ZnO溶胶浓度从0.7mol/L降低到0.006mol/L,制备的ZnO薄膜从只出现一个380nm(对应的光学禁带宽度为3.27eV)左右的吸收边到在380和320nm(对应的光学禁带宽度为3.76eV)左右各出现一个吸收边,并且随着ZnO溶胶浓度的降低,在380—320nm波段内的透过率明显提高.而Z 关键词： 纳米ZnO 2复合薄膜')" href="#">ZnO-SiO₂复合薄膜 溶胶凝胶法 透射率     

Annealing effects on the structural and electrical transport properties of n-type Bi2Te2.7Se0.3 thin films deposited by flash evaporation

N-type Bi₂Te_2.7Se_0.3 thermoelectric thin films with thickness 800 nm have been deposited on glass substrates by flash evaporation method at 473 K. Annealing effects on the thermoelectric properties of Bi₂Te_2.7Se_0.3 thin films were examined in the temperature range 373-573 K. The structures, morphology and chemical composition of the thin films were characterized by X-ray diffraction, field emission scanning electron microscope and energy dispersive X-ray spectroscopy, respectively. Thermoelectric properties of the thin films have been evaluated by measurements of the electrical resistivity and Seebeck coefficient at 300 K. The Hall coefficients were measured at room temperature by the Van der Pauw method. The carrier concentration and mobility were calculated from the Hall coefficient. The films thickness of the annealed samples was measured by ellipsometer. When annealed at 473 K, the electrical resistivity and Seebeck coefficient are 2.7 mΩ cm and −180 μV/K, respectively. The maximum of thermoelectric power factor is enhanced to 12 μW/cm K².     

ZnSe/SiO2复合薄膜光学常数与荧光光谱的研究

采用溶胶-凝胶工艺与原位生长技术，制备了ZnSe/SiO₂复合薄膜.X射线衍射分 析表明薄膜中ZnSe晶体呈立方闪锌矿结构.X射线荧光分析结果显示薄膜中Zn与Se摩尔比为1 ∶1.01—1∶1.19.利用场发射扫描电子显微镜观察了复合薄膜的表面形貌，结果表明复合薄 膜表面既存在尺寸约为400nm的ZnSe晶粒，也存在尺寸小于100nm的ZnSe晶粒.利用椭偏仪测 量了薄膜椭偏角Ψ，Δ与波长λ的关系，采用Maxwell-Garnett有效介质理论对薄膜的光学 常数、厚度、气孔率、ZnS 关键词： 2复合薄膜')" href="#">ZnSe/SiO₂复合薄膜 光学性质 椭偏光度法 荧光光谱     

Effect of complexing agent on the properties of electrochemically deposited Cu2ZnSnS4 (CZTS) thin films

The Cu₂ZnSnS₄ (CZTS) thin films have been electrochemically deposited on Mo-coated glass substrate from weak acidic medium (pH 4.5-5) at room temperature. The effect of complexing agent (tri-sodium citrate) on the structural, morphological and compositional properties of CZTS thin films has been investigated. The as-deposited and annealed thin films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM),EDAX and X-ray photoelectron spectroscopy (XPS) techniques for their structural, morphological, compositional and chemical properties, respectively. XRD studies reveal that the amorphous nature of as-deposited thin film changes into polycrystalline with kesterite crystal structure after annealing in Ar atmosphere. The film prepared without complexing agent showed well-covered surface morphology on the substrate with some cracks on the surface of the film whereas those prepared using complexing agent, exhibited uneven and slightly porous and some overgrown particles on the surface of the films. After annealing, morphology changes into the flat grains, uniformly distributed over the entire surface of the substrate. The EDAX and XPS study reveals that the films deposited using 0.2 M tri-sodium citrate are nearly stoichiometric.     

Structural and optical properties of SrCu2O2 films deposited on sapphire substrates by pulsed laser deposition

We deposited SrCu₂O₂ (SCO) films on sapphire (Al₂O₃) (0 0 0 1) substrates by pulsed laser deposition. The crystallographic orientation of the SCO thin film showed clear dependence on the growth temperature. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis showed that the film deposited at 400 °C was mainly oriented in the SCO [2 0 0] direction, whereas when the growth temperature was increased to 600 °C, the SCO film showed a dominant orientation of SCO [1 1 2]. The SCO film deposited at 500 °C was obvious polycrystalline, showing multi peaks from (2 0 0), (1 1 2), and (2 1 1) diffraction in the XRD spectrum. The SCO film deposited at 600 °C showed a band gap energy of 3.3 eV and transparency up to 80% around 500 nm. The photoluminescence (PL) spectra of the SCO films grown at 500 °C and 600 °C mainly showed blue-green emission, which was attributed to the intra-band transition of the isolated Cu⁺ and Cu⁺–Cu⁺ pairs according to the temperature dependent-PL analysis.     

Structural, magnetic and electronic structure studies of Mn doped TiO2 thin films

We report structural, magnetic and electronic structure study of Mn doped TiO₂ thin films grown using pulsed laser deposition method. The films were characterized using X-ray diffraction (XRD), dc magnetization, X-ray magnetic circular dichroism (XMCD) and near edge X-ray absorption fine structure (NEXAFS) spectroscopy measurements. XRD results indicate that films exhibit single phase nature with rutile structure and exclude the secondary phase related to Mn metal cluster or any oxide phase of Mn. Magnetization studies reveal that both the films (3% and 5% Mn doped TiO₂) exhibit room temperature ferromagnetism and saturation magnetization increases with increase in concentration of Mn doping. The spectral features of XMCD at Mn L_3,2 edge show that Mn²⁺ ions contribute to the ferromagnetism. NEXAFS spectra measured at O K edge show a strong hybridization between Mn, Ti 3d and O 2p orbitals. NEXAFS spectra measured at Mn and Ti L_3,2 edge show that Mn exist in +2 valence state, whereas, Ti is in +4 state in Mn doped TiO₂ films.     

Structural and optical properties of pulsed laser deposited SrBi2Nb2O9 thin films

SrBi₂Nb₂O₉ (SBN) thin films were prepared on fused quartz substrates at room temperature by pulsed laser deposition. The influence of deposition parameters such as target-to-substrate distance, oxygen pressure and annealing temperature on film crystallization behavior was investigated by X-ray diffraction. Results indicated that the films grown at the optimum processing conditions have polycrystalline structure with a single layered perovskite phase. The optical transmittance of the films prepared at various oxygen pressures was measured in the wavelength range 200–900 nm using UV–vis spectrophotometer. The results showed that there is a red shift in the optical absorption edge with a rise in the oxygen pressure. Refractive index as a function of wavelength and optical band gap of the films were determined from the optical transmittance spectra. The results indicated that the refractive index increases with increasing oxygen pressure at the same incident light wavelength, while the band gap reduces from 4.13 to 3.88 eV. It may be attributed to an increase in packing density and grain size, and decrease in oxygen defects.     

The microwave response of MgB2 /Al2O3 superconducting thin films

Microwave characteristics of MgB2/Al2O3 superconducting thin films were investigated by coplanar resonator technique. The thin films studied have different grain sizes resulting from different growth techniques. The experimental results can be described very well by a grain-size model which combines coplanar resonator theory and Josephson junction network model. It was found that the penetration depth and surface resistance of thin films with smaller grain sizes are larger than those of thin films with larger grain sizes.     

Composition-induced structural modifications in the quaternary CuIn1-xGaxSe2 thin films： bond properties versus Ga content

In this paper the dependence of structural properties of the quaternary CuIn1-xGaxSe2 films with tetragonal structure on the Ga content has been systematically investigated by Raman scattering and x-ray diffraction spectra. The shift of the dominant A1 mode, unlike the lattice constants, does not follow the linear Vegard law with increasing Ga content x, whereas exhibits approximately polynomial change from 174 cm^-1 for CuInSe2 to 185 cm^-1 for CuGaSe2. Such behaviour should be indicative of presence of the asymmetric distribution of Ga and In on a microscopic scale in the films, due to Ga addition. The changes in the tetragonal distortion η lead to a significant variation in the anion displacement parameter U, which should be responsible for the evolution of bond parameters and resultant Raman bands with x.     

The structure and photocatalytic activity of TiO2 thin films deposited by dc magnetron sputtering

This paper seeks to determine the optimal settings for the deposition parameters, for TiO₂ thin film, prepared on non-alkali glass substrates, by direct current (dc) sputtering, using a ceramic TiO₂ target in an argon gas environment. An orthogonal array, the signal-to-noise ratio and analysis of variance are used to analyze the effect of the deposition parameters. Using the Taguchi method for design of a robust experiment, the interactions between factors are also investigated. The main deposition parameters, such as dc power (W), sputtering pressure (Pa), substrate temperature (°C) and deposition time (min), were optimized, with reference to the structure and photocatalytic characteristics of TiO₂. The results of this study show that substrate temperature and deposition time have the most significant effect on photocatalytic performance. For the optimal combination of deposition parameters, the (1 1 0) and (2 0 0) peaks of the rutile structure and the (2 0 0) peak of the anatase structure were observed, at 2θ ∼ 27.4°, 39.2° and 48°, respectively. The experimental results illustrate that the Taguchi method allowed a suitable solution to the problem, with the minimum number of trials, compared to a full factorial design. The adhesion of the coatings was also measured and evaluated, via a scratch test. Superior wear behavior was observed, for the TiO₂ film, because of the increased strength of the interface of micro-blasted tools.