Mechanoluminescence and thermoluminescence of Mn doped ZnS nanocrystals

This paper reports the synthesis of ZnS:Mn nanocrystals by the chemical route in which mercaptoethanol was used as the capping agent. The particle size of such nanocrystals was measured using XRD and TEM patterns and was found to be in between 3and 5 nm. It was found that the peak position of TL glow curve and the TL intensity of ZnS:Mn nanoparticles increases as the particle size is decreased. The isothermal decay technique is used to determine the trap-depth. The stability of the charge carriers in the traps increase with the decrease in size of the nanoparticles. The higher stability may be attributed to the higher surface/volume ratio and also to the increase in the trap-depth with decreasing particle size. When a ZnS:Mn nanocrystal is deformed the peak intensity I_m increases linearly with the increasing height of the load. After I_m, initially the ML intensity decreases at a fast rate, and later on it decreases at a slow rate. The ML in ZnS:Mn nanocrystals can be understood on the basis of the piezoelectrically induced electron detrapping model.     

Tb ions in presence of ZnS:Mn nanocrystals immobilized on silica: Energy transfer ZnS→Tb and coordination state of Mn ions

Three-component luminescent material consisting of silica xerogel as a support with immobilized ZnS:Mn²⁺ nanocrystals and Tb³⁺ ions was compared with such two-component materials as the silica support with ZnS:Mn²⁺ as well as the support with Tb³⁺. In each case the nanocrystals and the lanthanide ions were immobilized at silica surface by impregnation procedure. Size of the ZnS quantum dots doped with Mn²⁺ were estimated by Scherrer method from the X-ray diffraction (XRD) pattern. The materials have been characterized by EPR and optical spectroscopy techniques. EPR spectra allow to distinguish two different Mn²⁺ sites: the first is assigned to isolated Mn²⁺ substitutionally and incorporated into cubic ZnS lattice and the second is ascribed to the Mn²⁺ situated near the nanocrystal surface. From the optical spectra we have found that in the three-component material, energy transfer from excited ZnS:Mn²⁺ nanocrystals to Tb³⁺ ions takes place. The different mechanisms of such transfer are discussed.     

Fast two-step microwave-activated synthesis of Mn doped ZnS nanocrystals: Comparison of the luminescence and doping process with thermochemical approach

In this work we report a fast two-step microwave activated synthesis of the ZnS:Mn nanocrystals. Zn(NO₃)₂ and Na₂S₂O₃ were used as the precursors and Mn(NO₃)₂ was employed as the source of the impurity. The aqueous synthesis was based on the heat sensitivity of Na₂S₂O₃, which releases some S species on heating. Consequently, the reaction was well activated under microwave irradiation resulting in formation of ZnS:Mn nanocrystals. Thioglycerol (TG) was also used as the capping agent and the catalyst of the reaction. The synthesis process was done in two steps, i.e. 1 min irradiation without TG and then injection of TG and continuation of irradiation. ZnS:Mn nanocrystals were quickly formed in the solution and luminescence was emerged in a few minutes. Optical transmission spectroscopy and X-ray diffraction analysis demonstrated formation of ZnS:Mn nanocrystals with a cubic crystalline structure and 3.0 nm average size. Photoluminescence measurements also showed some spectra with a Mn related peak located at 585 nm. The mentioned peak corresponds to ⁴T₁→⁶A₁ transition in Mn impurities and revealed the effective incorporation of Mn ions inside the nanocrystals. Evolution of the PL was also investigated and showed an increase in longer irradiation times. A qualitative model is also used to justify the necessity of using a two-step method as well as the PL emergence and increase in longer irradiation times. The model is based on separation between the nucleation and growth steps and significant role of TG in these stages. Finally, we present a comparison between the results of microwave activated method and two-step thermochemical approach. Although the synthesis time in microwave activated method was considerably short (less than 5 min), the luminescence properties were quite comparable with long time thermochemical approach. The doping process was also investigated for different Mn/Zn concentrations in two approaches. The results demonstrated that the doping occurred more effectively in the microwave activated synthesis.     

核-壳结构的ZnS:Mn纳米粒子的荧光增强

采用反胶束方法制备了ZnS :Mn纳米粒子并对其进行了ZnS壳层修饰 ,采用发射光谱和激发光谱对其光学性质进行了研究。与未包覆的ZnS:Mn纳米粒子相比 ,核 壳结构的ZnS :Mn纳米粒子来自于Mn2 离子的 5 80nm的发光增强了数倍 ,归因于ZnS壳增加了Mn2 离子到纳米颗粒表面的距离 ,减弱了Mn2 离子向表面猝灭中心的传递。样品制备后 ,核 壳结构的ZnS :Mn纳米粒子在 5 80nm的发光随时间略有增强 ,激发光谱的位置未发生明显变化 ,而未包覆的ZnS:Mn纳米粒子在 5 80nm的发光显著增强 ,同时自激活发光减弱 ,激发光谱明显发生红移 ,说明未包覆的ZnS :Mn纳米粒子的尺寸随时间增大 ,而核 壳结构的ZnS :Mn纳米粒子尺寸基本不变。     

核/壳结构的ZnS:Mn/SiO_2纳米粒子的制备及发光性质研究

采用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS∶Mn),然后利用正硅酸乙酯(TEOS)的水解反应对其进行了不同厚度的SiO2无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及荧光发射光谱(PL)对样品的结构及光学性质进行了表征和研究。包覆SiO2壳层后,粒子的粒径明显增大并且在ZnS∶Mn纳米粒子表面可以观察到明显的SiO2壳层。XPS测试印证了ZnS∶Mn/SiO2的核壳结构。随着SiO2壳层的增厚,ZnS∶Mn/SiO2的Mn离子的发光先增强后减弱,这是因为SiO2壳层同时具有表面修饰和降低发光中心浓度这两种相反的作用。当壳层厚度(壳与核的物质的量的比)达到5时,发光效果达到最好,其强度达到未包覆样品的7.5倍。     

核/壳结构ZnS : Mn/CdS纳米粒子的制备及发光

利用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS : Mn),利用沉淀法对ZnS ∶ Mn纳米粒子进行了不同厚度的CdS无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及光致发光(PL)光谱等手段对样品进行了表征。TEM显示粒子为球形,直径大约在14~18 nm之间。由XRD结果可以看出CdS壳层的形成过程受到了ZnS ∶ Mn核的影响,导致其结晶较差。XRD和XPS测量证明了ZnS : Mn/CdS的核壳结构。随着CdS壳层的增厚,样品的发光强度呈现一直减弱的现象。     

Studies on the spin Hamiltonian parameters for Mn2+ in the ZnS nanocrystals and bulks

The spin Hamiltonian parameters (zero-field splitting D, g factors and hyperfine structure constants) are theoretically studied for Mn²⁺ in the ZnS nanocrystals and bulks from the perturbation formulae of these quantities for trigonal and cubic tetrahedral 3d⁵ clusters, respectively. The trigonal Mn²⁺ centre in the ZnS nanocrystals is attributed to the impurity–ligand bond angle related to the C₃ axis about 0.39° larger than that (≈109.47°) of an ideal tetrahedron. Almost the same g factors and hyperfine structure constants for the nanocrystals and bulks can be ascribed to similar crystal-field environments (i.e. comparable cubic field parameters Dq), nearly the same covalency (i.e. the equal covalency factors N) and the Mn²⁺ 3d–3s orbital admixture (i.e. the identical core polarisation constants κ) in both systems. The ligand orbital and spin–orbit coupling contributions are found to be important and should be included in the electron paramagnetic resonance analysis in view of significant covalency.     

White organic electroluminescence from fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc doped with phosphorescent material

Efficient white electroluminescence has been obtained by using an electroluminescent layer comprising of a blue fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(hpb)₂] doped with red phosphorescent bis (2-(2′-benzothienyl) pyridinato-N,C^3′)iridium(acetylacetonate) [Ir(btp)₂acac] molecules. The color coordinates of the white emission spectrum was controlled by optimizing the concentration of red dopant in the blue fluorescent emissive layer. Organic light-emitting diodes were fabricated in the configuration ITO/α-NPD/Zn(hpb)₂:0.01 wt%Ir(btp)₂acac/BCP/Alq₃/LiF/Al. The J-V-L characteristic of the device shows a turn on voltage of 5 V. The electroluminescence (EL) spectra of the device cover a wide range of visible region of the electromagnetic spectrum with three peaks around 450, 485 and 610 nm. A maximum white luminance of 3500 cd/m² with CIE coordinates of (x, y=0.34, 0.27) at 15 V has been achieved. The maximum current efficiency and power efficiency of the device was 5.2 cd/A and 1.43 lm/W respectively at 11.5 V.     

Synthesis, optical, structural and thermal characterization of Mn doped ZnS nanoparticles using reverse micelle method

Mn²⁺­doped ZnS nanoparticles have been prepared through the reverse micelles method using sodium bis (2-ethylhexyl) sulfosuccinate (AOT) as a surfactant. The prepared particles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infra-red spectrometer (FT-IR), UV-vis spectrometry, photoluminescence (PL), electron spin resonance (ESR) and thermogravimetry-differential scanning calorimetry (TG-DSC).     

Luminescence enhancement in bromine and samarium co-doped TiO2 semiconductor nanocrystalline powders

In this paper, TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with different amounts of Br⁻ were prepared by an improved sol-gel method and were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), VG ESCALAB MKIIX-ray photoelectron spectrometer (XPS) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). Their photoluminescence (PL) properties were investigated at room temperature. The emissions of ⁴G_5/2-⁶H_J (J=5/2, 7/2, 9/2) transitions of Sm³⁺ ions were observed under the excitation wavelength at 350 nm and the emission intensity depended strongly on the doping amount of Br⁻. TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with 1 mol% of Br⁻ calcined at 700 °C exhibit highest intensity of luminescence, which is nearly three times than the undoped one. The mechanism of photoluminescence in the co-doped system was discussed.     

ZnS:Mn纳米荧光粉的制备

介绍一种制备ZnS:Mn纳米荧光粉的化学合成方法。本合成通过调节甲基丙烯酸与巯基乙酸的摩尔比，可在1.8-3nm范围内对纳米粒径进行很好的控制。生成的聚甲基丙烯酸包敷了ZnS:Mn纳米微粒，从而防止了纳米微粒团聚，同时增强了纳米微粒的抗氧化性，大大提高了纳米荧光粉的发光效率和发光稳定性。通过透射电镜（TEM）、X射线粉末衍射（XRD）和光致发光谱（PL）对所制得的纳米粉末进行了表征。     

Energy transfer dynamics between Alq3 and CdTeS/ZnS core shell nanocrystals

The photoluminescence (PL) properties of the guest-host films, using CdTeS/ZnS core shell quantum dots (QDs) as the guest and organic small-molecule material Alq₃ as the host, are studied by steady-state and time-resolved PL spectroscopy. Both the relative intensity and the PL lifetime are intensively dependent on the weight ratio of Alq₃ and CdTeS/ZnS QDs. The detailed analysis provides clear evidence for a Förster energy transfer from Alq₃ host to QDs guest, based on the nonradiative resonant transfer mechanism. The results are relevant to the application of hybrid organic/inorganic systems to OLEDs.     

Synthesis, characterization and optical properties of water-soluble ZnS:Mn nanoparticles

ZnS nanoparticles with Mn²⁺ doping (0.5-20%) have been prepared through a simple chemical method, namely the chemical precipitation method. The structure of the nanoparticles has been analyzed using X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and UV-vis spectrometer. The size of the particles is found to be 3-5 nm range. Photoluminescence spectra were recorded for undoped ZnS nanoparticles using an excitation wavelength of 320 nm, exhibiting an emission peak centered at around 445 nm. However, from the Mn²⁺-doped samples, a yellow-orange emission from the Mn²⁺⁴T₁-⁶A₁ transition is observed along with the blue emission. The prepared Mn²⁺-doped sample shows efficient emission of yellow-orange light with the peak emission 580 nm with the blue emission suppressed. The maximum PL intensity is observed only at the excitation energy of 3.88 eV (320 nm). Increase in stabilizing time up to 48 h in de-ionized water yields the enhancement of emission intensity of doped (4% Mn²⁺) ZnS. The correlation made through the concentration of Mn²⁺ versus PL intensity resulted in opposite trend (mirror image) of blue and yellow emissions.     

Luminescence channels of manganese-doped spinel

Two independent luminescence channels are observed from manganese-doped spinel Mn:MgAl₂O₄. The luminescence around 520 nm is assigned to transition from the lowest electronic excited state ⁴T₁ to the ground state ⁶A₁ of Mn²⁺ (3d)⁵ ion by analyzing the excitation spectrum and electron spin resonance measurement. The emission at 650 nm is triggered by the band edge excitation and is assigned similarly to the charge-transfer process associated with the manganese ion.     

Synthesis of robust water-soluble ZnS:Mn/SiO2 core/shell nanoparticles

Water-soluble Mn doped ZnS (ZnS:Mn) nanocrystals synthesized by using 3-mercaptopropionic acid (MPA) as stabilizer were homogeneously coated with a dense silica shell through a multi-step procedure. First, 3-mercaptopropyl triethoxy silane (MPS) was used to replace MPA on the particle surface to form a vitreophilic layer for further silica deposition under optimal experimental conditions. Then a two-step silica deposition was performed to form the final water-soluble ZnS:Mn/SiO₂ core/shell nanoparticles. The as-prepared core/shell nanoparticles show little change in fluorescence intensity in a wide range of pH value.     

Zn2SiO4(ZnB2O4):Mn2+,Sm3+发光材料的制备与荧光性能

使用高温固相法首次合成了Zn2SiO4(ZnB2O4):Mn2+,Sm3+发光材料,探讨了烧结温度、Sm2+含量对样品荧光性能的影响.利用X射线衍射(XRD)、荧光光谱等分析手段对Zn2SiO4(ZnB2O4):Mn2+,Sm3+粉末的结构、发光性能进行了表征.确定了该荧光材料的最佳合成条件,离子掺杂浓度等.实验结果表...     

Synthesis and characterization of Cu doped ZnS nanoparticles using TOPO and SHMP as capping agents

Undoped and Cu²⁺ doped (0.2-0.8%) ZnS nanoparticles have been synthesized through chemical precipitation method. Tri-n-octylphosphine oxide (TOPO) and sodium hexametaphosphate (SHMP) were used as capping agents. The synthesized nanoparticles have been analyzed using X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectrometer (FT-IR), UV-vis spectrometer, photoluminescence (PL) and thermo gravimetric-differential scanning calorimetry (TG-DTA) analysis. The size of the particles is found to be 4-6 nm range. Photoluminescence spectra were recorded for ZnS:Cu²⁺ under the excitation wavelength of 320 nm. The prepared Cu²⁺-doped sample shows efficient PL emission in 470-525 nm region. The capped ZnS:Cu emission intensity is enhanced than the uncapped particles. The doping ions were identified by electron spin resonance (ESR) spectrometer. The phase changes were observed in different temperatures.     

Photoluminescence of colloidal YVO4:Eu/SiO2 core/shell nanocrystals

YVO₄:Eu, and YVO₄:Eu/SiO₂ nanocrystals (NCs) were prepared by hydrothermal method with citrate as capping ligands. Their morphologies, structures, components, and photoluminescence properties were investigated and presented in this paper. A remarkable fluorescence enhancement up to 2.17 times was observed in colloidal YVO₄:Eu/SiO₂ NCs, compared to that of colloidal YVO₄:Eu NCs. This is mainly attributed to the formation of the outer protecting layers of biocompatible SiO₂ shells; which shield the Eu³⁺ ions effectively from water and thus reduces the deleterious effects of water on the luminescence. Meanwhile, on the basis of laser selective excitation, two kinds of luminescent centers were confirmed in the NCs, namely, inner Eu³⁺ ions and surface Eu³⁺ ions. The surface modifications for YVO₄:Eu NCs effectively reduced the surface defects and accordingly enhanced the luminescence. The core/shell NCs exhibited long fluorescence lifetime and high photostability under ultraviolet radiation.     

Influence of high-pressure hydrogen treatment on structural and electrical properties of ZnO thin films

ZnO thin films were treated by high-pressure hydrogen (H₂). Scanning electron microscope (SEM) images show that the surface morphology of ZnO films has been changed significantly by H₂ treatment. X-ray diffraction patterns show that the Zn(OH)₂ phases formed after H₂ treatment. The X-ray photoelectron spectroscopy results indicate that H atoms were doped into the surface of ZnO by forming H-O-Zn bond. The phenomenon shows that it is easy to form O-H bond in ZnO rather than H interstitial atom under high-pressure hydrogen circumstance.     

Luminescence of Ce and Pr doped Sr2Mg(BO3)2 under VUV-UV and X-ray excitation

This report presents the luminescence properties of Ce³⁺ and Pr³⁺ activated Sr₂Mg(BO₃)₂ under VUV-UV and X-ray excitation. The five excitation bands of crystal field split 5d states are observed at about 46 729, 44 643, 41 667, 38 314 and 29 762 cm⁻¹ (i.e. 214, 224, 240, 261 and 336 nm) for Ce³⁺ in the host lattice. The doublet Ce³⁺ 5d→4f emission bands were found at about 25 840 and 24 096 cm⁻¹ (387 and 415 nm). The influence of doping concentration and temperature on the emission characteristics and the decay time of Ce³⁺ in Sr₂Mg(BO₃)₂ were investigated. For Pr³⁺ doped samples, the lowest 5d excitation band was observed at about 42017 cm⁻¹ (238 nm), a dominant band at around 35714 cm⁻¹ (280 nm) and two shoulder bands were seen in the emission spectra. The excitation and emission spectra of Ce³⁺ and Pr³⁺ were compared and discussed. The X-ray excited luminescence studies show that the light yields are ∼3200±230 and ∼1400±100 photons/MeV of absorbed X-ray energy for the samples Sr_1.86Ce_0.07Na_0.07Mg(BO₃)₂ and Sr_1.82Pr_0.09Na_0.09Mg(BO₃)₂ at RT, respectively.