Optical properties of thin Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript>, films produced by RF magnetron sputtering

Optical properties of thin Cu₂ZnSnS₄ films produced by RF magnetron sputtering of preliminarily synthesized material are studied. Transmission and reflection coefficients are studied in a range from 0.4 to 26 μm. The optical band-gap width depending on substrate temperature is estimated; in optimal modes, it is equal to 1.47 eV. The study of electrical properties shows that Cu₂ZnSnS₄ possesses low charge-carrier mobility, μ = 1.9 cm²/(V s), at room temperature and hole concentration р = 5 × 10¹⁸ cm^–3. Electron microscopy shows that the film possesses a polycrystalline structure with a crystallite size on the order of 100 nm.     

Synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles with tunable magnetism by the modified hydrothermal method

Cobalt ferrite (CoFe₂O₄) nanoparticles were synthesized by using the hydrothermal route with the addition of trisodium citrate dihydrate (Na₃CA·2H₂O). The formation of CoFe₂O₄ nanoparticles with size ranging from 13 to 19 nm was confirmed by X-ray diffraction, energy dispersive X-ray analysis, and Fourier transform infrared spectroscopy; the clear-cut sharp of the nanoparticles was observed by transmission electron microscopy. By these characterization methods, the evolution of lattice constant and morphologies of the nanoparticles with the addition of Na₃CA·2H₂O is observed. Furthermore, the magnetic hysteresis loops measured at room temperature indicate that the magnetic properties of the products also show clear relationship with the masses of Na₃CA·2H₂O. For example, coercivity and high-field paramagnetic susceptibility increase with the increasing masses of Na₃CA·2H₂O, whereas the saturation magnetization and the effective magnetic anisotropy constant have the maximum values as the mass of Na₃CA·2H₂O is 1 g. This change of magnetic properties is related with the expanded lattice and the varied size and shape because of the addition of Na₃CA·2H₂O.     

Optical properties and mechanisms of current flow in Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> films prepared by spray pyrolysis

Thin films Cu₂ZnSnS₄ (up to 0.9 μm thick) with p-type conductivity and band gap E_g = 1.54 eV have been prepared by the spray pyrolysis of 0.1 M aqueous solutions of the salts CuCl₂ · 2H₂O, ZnCl₂ · 2H₂O, SnCl₄ · 5H₂O, and (NH₂)₂CS at a temperature T_S = 290°C. The electrophysical properties of the films have been analyzed using the model for polycrystalline materials with electrically active grain boundaries. The energy and geometric parameters of the grain boundaries have been determined as follows: the height of the barriers is E_b ≈ 0.045–0.048 eV, and the thickness of the depletion region is δ ≈ 3.25 nm. The effective concentrations of charge carriers p₀ = 3.16 × 10¹⁸ cm^–3 and their mobilities in crystallites μ_p = 85 cm²/(V s) have been found using the technique for determining the kinetic parameters from the absorption spectra of thin films at a photon energy hν ≈ E_g. The density of states at grain boundaries N_t = 9.57 × 10¹¹ cm^–2 has been estimated.     

Magnetic resonance of Cu and of Gd in insulating GdSr<Subscript>2</Subscript>Cu<Subscript>2</Subscript>NbO<Subscript>8</Subscript> and in superconducting GdSr<Subscript>2</Subscript>Cu<Subscript>2</Subscript>RuO<Subscript>8</Subscript>

Weak-ferromagnetic (or antiferromagnetic) resonance of Cu and electron spin resonance (ESR) of Gd are observed both in insulating GdSr₂Cu₂NbO₈ and in superconducting GdSr₂Cu₂RuO₈. The Cu resonance implies that the CuO₂ planes are magnetic and indicates that the superconducting layer of GdSr₂Cu₂RuO₈ is SrO (not CuO₂), as in its related superconducting compound without cuprate planes, doped Sr₂YRuO₆.     

Preparing Cu₂ZnSnS₄ films using the co-electrodeposition method with ionic liquids

Cu₂ZnSnS4（CZTS） films are successfully prepared by co-electrodeposition in aqueous ionic solution and sulfurized in elemental sulfur vapor ambient at 400 C for 30 min using nitrogen as the protective gas.It is found that the CZTS film synthesized at Cu/（Zn+Sn）=0.71 has a kesterite structure,a bandgap of about 1.51 eV,and an absorption coefficient of the order of 10 4 cm 1.This indicates that the co-electrodeposition method with aqueous ionic solution is a viable process for the growth of CZTS films for application in photovoltaic devices.     

Ab initio study of thermoelectric properties of Cu<Subscript>3</Subscript>PSe<Subscript>4</Subscript> and Cu<Subscript>3</Subscript>PS<Subscript>4</Subscript>: alternative materials for thermoelectric applications

This letter discusses the thermoelectric properties of Cu₃PSe₄ and Cu₃PS₄ compounds, using the Ab initio calculations. These compounds are predicted to be good thermoelectric materials thanks to the nature of their band edge states. Seebeck coefficient of Cu₃PSe₄ exhibits a maximum value of 1256 µV/K at roopm temperature, whereas it is 2389 µV/K for Cu₃PS₄. Furthermore, the electrical conductivity is significantly enhanced with doping level while the electronic thermal conductivity is weakly increased. Besides, the factor of merit of these compounds shows a value around the unity only at low doping levels. Hence, this predicts that these compounds may present excellent thermoelectric properties, therefore they could be considered as alternatives for thermoelectric applications.     

Synthesis and microstructure of Co/Ni: MgGa<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

This report discusses the preparation and microstructure of Co/Ni co-doped MgGa₂O₄ nanoparticles. The nanoparticles with the size of 20–55 nm were synthesized by sol-gel method. The phase and crystallinity were confirmed by X-ray powder diffraction (XRD) pattern. The particle size was estimated according to XRD data and transmission electron microscopy. The electronic structure was studied using X-ray photoelectron spectroscopy (XPS). The XPS studies showed that Ga³⁺ ions possess tetrahedral and octahedral sites of spinel structure and the inverse degree (two times of the fraction of tetrahedral Ga³⁺ ions) has increased with the increase of the doping concentration of Co²⁺ and Ni²⁺ ions. For Co/Ni co-doped MgGa₂O₄, two broad absorption bands of 350~500 and 550~700 nm were observed in the absorption spectra. The broad band at 350~500 nm was assigned to the combination of the absorption of octahedral Co²⁺ and Ni²⁺ ions, whereas the absorption band at 550~700 nm is mainly due to tetrahedrally coordinated Co²⁺ ions and octahedrally coordinated Ni²⁺ ions.     

Magnetodielectric coupling by exchange striction in Y<Subscript>2</Subscript>Cu<Subscript>2</Subscript>O<Subscript>5</Subscript>

We have studied the magnetodielectric response of Y₂Cu₂O₅, the so-called blue phase in the Y₂O₃-CuO-BaO phase diagram. Based on symmetry principles, we predict and demonstrate magneto-dielectric coupling on a single crystal sample. We report an anomaly in the dielectric constant at the ordering temperature of the Cu spins. We probe the magnetic field-induced phase transitions between four different magnetic phases using magneto-capacitance measurements, demonstrating relatively strong magnetodielectric coupling. We observe an increase in dielectric constant in the spin-flip phase where there exists spontaneous magnetization. We construct a detailed magnetic phase diagram. The magnetodielectric coupling is analyzed in terms of striction induced by symmetric superexchange and optical phonon frequency shifts.     

EPR and optical absorption studies of Cu<Superscript>2+</Superscript> ions in [ZnPd(CN)<Subscript>4</Subscript>(C<Subscript>4</Subscript>H<Subscript>12</Subscript>N<Subscript>2</Subscript>O<Subscript>2</Subscript>)] single crystals

A Cu²⁺-doped single crystal of catena-trans-bis(N-(2-hydroxyethyl)-ethylenediamine) zinc(II)-tetra-m-cyanopaladate(II) [ZnPd(CN)₄(C₄H₁₂N₂O₂)] complex has been investigated by electron paramagnetic resonance (EPR) technique at room temperature. EPR spectra indicate that Cu²⁺ ions substitute for magnetically equivalent Zn²⁺ ions and form octahedral complexes in [ZnPd(CN)₄(C₄H₁₂N₂O₂)] hosts. The crystal field affecting the Cu²⁺ ion is nearly axial. The optical absorption studies show two bands at 322 nm (30864 cm⁻¹) and 634 nm (15337 cm⁻¹) which confirm the axial symmetry. The spin Hamiltonian parameters and the relevant wave function are determined.     

Anisotropy of g-factor of Cu<Subscript>2+</Subscript> ion and Anisotropic exchange interaction between Spins in antiferromagnetic Bi<Subscript>2</Subscript>CuO<Subscript>4</Subscript>

To study the anisotropy of g-factor of Cu²⁺ ion in the antiferromagnetic Bi₂CuO₄ having an interesting crystal structure, we calculate the energy splitting of the orbital state of Cu²⁺ ion due to the electric crystalline field arising from the surrounding O²⁺, Bi³⁺ and Cu²⁺ ions. On the basis of Pryce's spin Hamiltonian we evaluate g-tensor of each Cu²⁺ ion in the unit cell. We also discuss the anisotropic exchange interaction which is important as the origin of the anisotropy energy for Cu²⁺ ion with S=1/2. The results are discussed in connection with observations.     

Synthesis and magnetic characterization of CoMoN<Subscript>2</Subscript> nanoparticles

A new ternary nitride, CoMoN₂, was prepared in the nanosize regime of 9.0 ± 2.0 nm, by nitridation of the precursor intermetallic nitride Co₃Mo₃N. XRD–Rietveld analysis revealed the presence of 0.60 (±0.02) mass % of Co impurity phase. The calculated space groups of CoMoN₂ and Co are P6 ₃ /mmc and Fm-3m, respectively. The N atoms lie at the interstitial sites and the 12 calculated nitrogen sites indicate the presence of a layered structure. The XPS studies indicated the presence of the nitride and surface oxynitride/oxide phases. CoMoN₂ is an interstitial nitride with Co and Mo in the zero oxidation state. The room temperature susceptibility is estimated after subtracting the ferromagnetic contribution from cobalt and found to be 2.7 × 10⁻⁴ emu g⁻¹ Oe⁻¹, indicating the Pauli-paramagnetic nature. The ferromagnetic exchange interactions between the Co atoms in CoMoN₂ are reduced due to the presence of Mo and N in the crystal lattice. The hysteresis loop shift 19 Oe is attributed to the demagnetizing dipolar fields created in the soft CoMoN₂ phase by the hard Co phase.     

Magnetic structure of the Sr<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>4</Subscript>Cl<Subscript>2</Subscript> two-subsystem antiferromagnet according to nuclear quadrupole resonance data

The magnetic structure of the Sr₂Cu₃O₄Cl₂ two-subsystem antiferromagnet is studied by the nuclear quadrupole resonance (NQR) method on the ^{63, 65}Cu and ³⁵Cl nuclei. The resonance spectrum above T _N2 = 40 K is determined by the Zeeman splitting of the levels of the ^{63, 65}Cu nuclei of the copper atoms at the Cu1 site with the first-order quadrupole perturbation. The magnetic field on the copper nuclei is equal to 93 kOe. The spectrum below n is significantly different: it includes a low-frequency part, which is associated with the ordering of the second magnetic subsystem Cu2. The splitting of the NQR lines of ³⁵Cl is observed above and below T _N2. This fact indicates the ferromagnetic ordering of the moments of the Cu1 subsystem, which are located along the c axis of the crystal, and makes it possible to determine the direction of the magnetic field on Cu1 copper as (110).     

Synthesis of MgAl<Subscript>2</Subscript>O<Subscript>4</Subscript> spinel nanoparticles using a mixture of bayerite and magnesium sulfate

This article reports a novel method to prepare MgAl₂O₄ spinel nanoparticles. By calcining a powder mixture of bayerite and magnesium sulfate at 800 °C and washing with water, single-phase MgAl₂O₄ spinel nanoparticles were prepared. The powder mixture and the calcined products were characterized by differential thermal and thermogravimetric analysis (DSC-TG), X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer–Emmett–Teller (BET) nitrogen-gas adsorption method. The obtained MgAl₂O₄ spinel nanoparticles have an average particle size of 12 nm, a narrow size distribution, and weak agglomeration. The specific surface area of the MgAl₂O₄ spinel powder is 110 m²/g. The formation of MgAl₂O₄ spinel is attributed to a solid-state reaction between γ-Al₂O₃ and MgSO₄.     

Microemulsion-mediated in-situ synthesis and magnetic characterization of polyaniline/Zn<Subscript>0.5</Subscript>Cu<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocomposite

Polyaniline/Zn_0.5Cu_0.5Fe₂O₄ nanocomposite was synthesized by a simple, general and inexpensive in-situ polymerization method in w/o microemulsion. The effects of polyaniline coating on the magnetic properties of Zn_0.5Cu_0.5Fe₂O₄ nanoparticles were investigated. The structural, morphological and magnetic properties of as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, scanning electron microscopy (SEM) and magnetic measurements. The morphology analysis confirmed that polyaniline was deposited on the porous surface of magnetic Zn_0.5Cu_0.5Fe₂O₄. It was shown that the saturation magnetization and coercivity of Zn_0.5Cu_0.5Fe₂O₄ decreased after polyaniline coating, which can be interpreted by the interparticle dipole–dipole interactions that contributed to magnetic anisotropy and changed the magnetic properties of the nanoparticles. PACS  74.25.Ha; 81.05.-t; 81.05.Lg     

HgO-added YB<Subscript>a2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript>−δ superconductors

The HgO-added YB_a2Cu₃O_7−δ (YBCO) superconductor has been studied for its structural and superconducting properties. Polycrystalline YBCO samples were synthesized through solid-state reaction method by adding HgO in different concentrations without using oxygen annealing. All the samples showed a sharp superconducting transition temperature around 90 K. The X-ray diffraction patterns of all the samples revealed monophasic Y-123 nature. The structural studies were carried out by neutron scattering and Rietveld analysis. The neutron scattering revealed that Hg is not incorporated in the Y-123 system and has shown optimum oxygen concentration. The significant role played by the HgO is to provide oxygen ambient through its decomposition, thus changing the oxygen balance in favour of high Cu-valence state.     

On the magnetism of Ln<Subscript>2/3</Subscript>Cu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> (Ln = lanthanide)

The magnetic and thermodynamic properties of the complete Ln_2/3Cu₃Ti₄O₁₂ series were investigated. Here Ln stands for the lanthanides La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, and Yb. All the samples investigated crystallize in the space group Im[`3]Im\bar{3} with lattice constants that follow the lanthanide contraction. The lattice constant of the Ce compound reveals the presence of Ce⁴⁺ leading to the composition Ce_1/2Cu₃Ti₄O₁₂. From magnetic susceptibility and electron-spin resonance experiments it can be concluded that the copper ions always carry a spin S = 1/2 and order antiferromagnetically close to 25 K. The Curie-Weiss temperatures can approximately be calculated assuming a two-sublattice model corresponding to the copper and lanthanide ions, respectively. It seems that the magnetic moments of the heavy rare earths are weakly coupled to the copper spins, while for the light lanthanides no such coupling was found. The 4f moments remain paramagnetic down to the lowest temperatures, with the exception of the Tm compound, which indicates enhanced Van-Vleck magnetism due to a non-magnetic singlet ground state of the crystal-field split 4f manifold. From specific-heat measurements we accurately determined the antiferromagnetic ordering temperature and obtained information on the crystal-field states of the rare-earth ions.     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Magnetism and optical properties of nanocrystalline Cu<Subscript>2</Subscript>O and TiO<Subscript>2</Subscript> powders

The optical spectra of Cu₂O and TiO₂ nanopowders have been studied, which contain information about structural defects and are of interest in the search for optimum regimes providing the synthesis of ferromagnetic nanocrystals with Curie temperatures above room temperature.     

Synthesis and characterization of hollow nanoparticles of crystalline Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>

Although Gd₂O₃ (gadolinia) nanoparticle is the subject of intense research interest due to its magnetic property as well as controllable emission wavelengths by doping of various lanthanide ions, it is known to be difficult to prepare monodisperse crystalline gadolinia nanoparticles because it requires high temperature thermal annealing process to enhance the crystallinity. In this article, we demonstrate the synthesis of hollow nanoparticles of crystalline Gd₂O₃ by employing poly(N-vinylpyrrolidone) (PVP) to stabilize the surface of Gd(OH)CO₃·H₂O nanoparticles and to successively form SiO₂ shell as a protecting layer to prevent aggregation during calcinations processes. Silica shells could be selectively removed after calcinations by a treatment with basic solution to give hollow nanoparticles of crystalline Gd₂O₃. The formation mechanism of hollow nanoparticles could be suggested based on several characterization results of the size and shape, and crystallinity of Gd₂O₃ nanoparticles by TEM, SEM, and XRD.