The enhanced catalytic degradation of SiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/C@TiO<Subscript>2</Subscript> photo-Fenton system on p-nitrophenol

Heterogeneous photo-Fenton SiO₂/Fe₃O₄/C@TiO₂ (SFCT) catalyst with a core-multishell structure and a diameter of about 550 nm was successfully prepared and was characterized by scanning electron microscopy (SEM), TEM, XRD, Raman, and Fourier transform infrared (FT-IR). The results illustrated that anatase TiO₂ coexisted with rutile TiO₂, in which the anatase phase was the main crystal phase. In addition, the catalytic activity of SFCT catalyst had been evaluated in the catalytic degradation on p-nitrophenol (PNP). The influence factors on the PNP degradation, including SFCT component ratio (m _SFC/ m _TiO2), H₂O₂ dosage, solution pH, and PNP concentration, had been investigated. And the contrast experiments about the photo-Fenton catalytic mechanism revealed that the SFCT-2 catalyst possessed a superior activity in the neutral environment due to the optimal activity matching between Fe₃O₄ and TiO₂, and it exhibited the stable catalytic performance after five successive recycles. Therefore, the SFCT-2 catalyst had a promising application for the photo-Fenton degradation of organic contaminant.     

Remarkable catalytic activity of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanocomposites prepared by hydrothermal method for the degradation of methyl orange

Visible light Bi₂O₃/TiO₂ nanocomposites are successfully prepared with different dosages of Bi₂O₃ by hydrothermal process. All the as-prepared samples are characterized by X-ray diffraction (XRD), scanning and transmission electron microscopes (SEM and TEM), Brunauer-Emmett-Teller analysis (BET), N₂ adsorption-desorption measurement, and UV-Vis diffuse reflectance spectra (DRS). XRD and Raman spectra reveal the anatase phase of both TiO₂ and Bi₂O₃/TiO₂ nanocomposites. X-ray diffraction patterns demonstrate that the bismuth ions did not enter into the lattice of TiO₂, and Bi₂O₃ is extremely dispersive on the surface of TiO₂ nanoparticles. The incorporation of Bi₂O₃ in TiO₂ leads to the spectral response of TiO₂ in the visible light region and efficient separation of charge carriers. The enhanced visible light activity is tested by the photocatalytic degradation of methyl orange under light illumination, and the performance of Bi₂O₃/TiO₂ nanocomposites are superior than that of pure TiO₂ which is ascribed to the efficient charge separation and transfer across the Bi₂O₃/TiO₂ junction. Bi₂O₃/TiO₂ nanocomposite (20 mg) loaded with 0.25 of Bi₂O₃ dispersed in 50 ml of 5 ppm methyl orange solution exhibited the highest photocatalytic activity of 98.86% within 240 min of irradiation, which is attributed to the low band gap, high surface area, and the strong interaction between Bi₂O₃ and TiO₂.     

Synthesis and characterization of bamboo-like CdS/TiO<Subscript>2</Subscript> nanotubes composites with enhanced visible-light photocatalytic activity

In order to efficiently use the visible light in the photocatalytic reaction, a novel bamboo-like CdS/TiO₂ nanotubes composite was prepared by a facile chemical reduction method, in which CdS nanoparticles located in the TiO₂ nanotubes. The composition and structure of this nanocomposite were characterized by TEM, HRTEM, XRD, XPS, FTIR and UV-vis spectroscopy. This CdS/TiO₂ nanotubes composite exhibited much higher visible-light photocatalytic activity for the degradation of methylene blue than pure TiO₂ nanotubes and CdS nanoparticles, and the highest photodegradation efficiency after 6 h irradiation can reach 84.5%. It is inferred that the unique structure of CdS/TiO₂ nanotubes composites acts an important role for the improvement of their photocatalytic activity.     

Influence of K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> on dielectric and barrier properties of polymer

Polymer composite comprising polyvinylidene fluoride (PVDF) and potassium hexatitante (K₂Ti₆O₁₃) was synthesized by solution casting. The effect of K₂Ti₆O₁₃ on surface, thermal, and electrical properties of polymer composite were investigated. The addition of K₂Ti₆O₁₃ with polymer leads to thermal degradation and transition of polymer composite from semi-crystalline to amorphous phase. The optimum results of contact angle for different loading wt% of K₂Ti₆O₁₃ were directly correlated with the surface morphology. Our experimental results confirmed the incorporation of K₂Ti₆O₁₃ in polymer by SEM micrographs. The evaluated dielectric properties (ε' = 424; tan δ = 2.14 at 130 °C and 100 Hz frequency for 20 wt% loading of K₂Ti₆O₁₃) for polymer composite are higher in compared to pure polymer. The enhancement in dielectric constant and changing the surface properties of polymer composite can be used for the development of electrochemical storage device applications.     

Photoaccumulating film systems based on TiO<Subscript>2</Subscript>/MoO<Subscript>3</Subscript> and TiO<Subscript>2</Subscript>/MoO<Subscript>3</Subscript>:V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanoheterostructures

The thin-film photocatalysts TiO₂/MoO₃ and TiO₂/MoO₃:V₂O₅ obtained by a combination of sol–gel and sintering techniques were studied using the photooxidation of probing dyes, EPR spectroscopy, X-ray diffraction analysis, and electron microscopy. It was shown that due to charge accumulation caused by UV irradiation, these photocatalysts retain their oxidative activity and ability for self-sterilization in the dark for a long time after irradiation was terminated (up to 5 h for TiO₂/MoO₃:V₂O₅).     

Efficient visible light-induced photoelectrocatalytic degradation of rhodamine B by polyaniline-sensitized TiO<Subscript>2</Subscript> nanotube arrays

Self-organized anodic TiO₂ nanotube arrays were sensitized with polyaniline by a simple electrodeposite method. The morphological and structural properties studied by scanning electron microscopy and fourier transform infrared spectroscopy reveal the successful deposition of polyaniline on the nanotube arrays. The polyaniline-sensitized TiO₂ nanotube arrays exhibit a distinguishable red shift on the absorption spectrum. Electrochemical impedance investigation attested to a significant improvement of the interfacial electron-transfer kinetics for promoted electron–hole effective separation. The as-prepared samples showed a high efficiency for the photoelectrocatalytic degradation of rhodamine B under visible-light irradiation (λ > 400 nm). The enhanced photoelectrocatalytic activity could be attributed to the extended absorption in the visible-light region by the polyaniline and the effective separation of photogenerated carriers driven by the photoinduced potential difference generated at the polyaniline/TiO₂ nanotube arrays interface.     

Facile one-pot synthesis of cellulose nanocrystal-supported hollow CuFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles as efficient catalyst for 4-nitrophenol reduction

A facile and efficient one-pot method for the synthesis of well-dispersed hollow CuFe₂O₄ nanoparticles (H-CuFe₂O₄ NPs) in the presence of cellulose nanocrystals (CNC) as the support was described. Based on the one-pot solvothermal condition control, magnetic H-CuFe₂O₄ NPs were in-situ grown on the CNC surface uniformly. TEM images indicated good dispersity of H-CuFe₂O₄ NPs with uniform size of 300 nm. The catalytic activity of H-CuFe₂O₄/CNC was tested in the catalytic reduction of 4-nitrophenol (4-NP) in aqueous solution. Compared with most CNC-based ferrite catalysts, H-CuFe₂O₄/CNC catalyst exhibited an excellent catalytic activity toward the reduction of 4-NP. The catalytic performance of H-CuFe₂O₄/CNC catalyst was remarkably enhanced with the rate constant of 3.24 s^?1 g^?1, which was higher than H-CuFe₂O₄ NPs (0.50 s^?1 g^?1). The high catalytic activity was attributed to the introduction of CNC and the special hollow mesostructure of H-CuFe₂O₄ NPs. In addition, the H-CuFe₂O₄/CNC catalyst promised good conversion efficiency without significant decrease even after 10 cycles, confirming relatively high stability. Because of its environmental sustainability and magnetic separability, H-CuFe₂O₄/CNC catalyst was shown to indicate that the ferrite nanoparticles supported on CNC were acted as a promising catalyst and exhibited potential applications in numerous ferrite based catalytic reactions.

Open image in new window

Graphical abstract ?

     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

Methane sensor based on SnO<Subscript>2</Subscript>/In<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> nanostructure

Two sets of samples of SnO₂/In₂O₃/TiO₂ system have been fabricated with different concentrations of component materials. In the first set TiO₂ with rutile structure was used, while in the second set it has the structure of anatase. Thin films (up to 50 nm) of obtained mixtures were deposited. Their sensitivity and selectivity with respect to methane (CH4) were studied. Nanostructure on the basis of 70%SnO₂ — 10%In₂O₃ — 20%TiO₂(anatase) exhibits sufficient sensitivity to methane.     

Minimizing of the boundary friction coefficient in automotive engines using Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and TiO<Subscript>2</Subscript> nanoparticles

Minimizing of the boundary friction coefficient is critical for engine efficiency improvement. It is known that the tribological behavior has a major role in controlling the performance of automotive engines in terms of the fuel consumption. The purpose of this research is an experimental study to minimize the boundary friction coefficient via nano-lubricant additives. The tribological characteristics of Al₂O₃ and TiO₂ nano-lubricants were evaluated under reciprocating test conditions to simulate a piston ring/cylinder liner interface in automotive engines. The nanoparticles were suspended in a commercially available lubricant in a concentration of 0.25 wt.% to formulate the nano-lubricants. The Al₂O₃ and TiO₂ nanoparticles had sizes of 8–12 and 10 nm, respectively. The experimental results have shown that the boundary friction coefficient reduced by 35–51% near the top and bottom dead center of the stroke (TDC and BDC) for the Al₂O₃ and TiO₂ nano-lubricants, respectively. The anti-wear mechanism was generated via the formation of protective films on the worn surfaces of the ring and liner. These results will be a promising approach for improving fuel economy in automotive.

Open image in new window

Graphical Abstract Minimizing of the boundary friction coefficient in automotive engines using Al₂O₃ and TiO₂ nanoparticles

     

The transport and thermal properties of glassy LiPO<Subscript>3</Subscript>/crystalline Al<Subscript>2</Subscript>O<Subscript>3</Subscript> (ZrO<Subscript>2</Subscript>) composite electrolytes

Glassy LiPO₃/crystalline Al₂O₃ and glassy LiPO₃/crystalline ZrO₂ (0–12.5 vol.% of oxide fillers) composite solid electrolytes have been prepared by glass matrix softening. Their thermal and transport properties have been investigated by differential scanning calorimetry (DSC) and impedance spectroscopy methods. The addition of ZrO₂ leads to a decrease in the crystallization temperature of LiPO₃ glass. It was found that the conductivity behavior depends on the nature of the dispersed addition. In the case of the Al₂O₃ addition, the increase in the electrical conductivity is observed. The ionic conductivity of the LiPO₃/10% Al₂O₃ composite reaches 5.8 × 10^?8 S/cm at room temperature. In contrast, the conductivity in the LiPO₃/ZrO₂ composite system decreases.     

Preparation and electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Ti<Subscript>4</Subscript>O<Subscript>7</Subscript> composite for lithium-ion batteries

In order to improve the rate capability of Li₄Ti₅O₁₂, Ti₄O₇ powder was successfully fabricated by improved hydrogen reduction method, then a dual-phase composite Li₄Ti₅O₁₂/Ti₄O₇ has been synthesized as anode material for lithium-ion batteries. It is found that the Li₄Ti₅O₁₂/Ti₄O₇ composite shows higher reversible capacity and better rate capability compared to Li₄Ti₅O₁₂. According to the charge-discharge tests, the Li₄Ti₅O₁₂/Ti₄O₇ composite exhibits excellent rate capability of 172.3 mAh g^?1 at 0.2 C, which is close to the theoretical value of the spinel Li₄Ti₅O₁₂. More impressively, the reversible capacity of Li₄Ti₅O₁₂/Ti₄O₇ composite is 103.1 mAh g^?1 at the current density of 20 C after 100th cycles, and it maintains 84.8% of the initial discharge capacity, whereas that of the bare spinel Li₄Ti₅O₁₂ is only 22.3 mAh g^?1 with a capacity retention of 31.1%. The results indicate that Li₄Ti₅O₁₂/Ti₄O₇ composite could be a promising anode material with relative high capacity and good rate capability for lithium-ion batteries.     

Photoactivity passivation of TiO<Subscript>2</Subscript> nanoparticles using molecular layer deposited (MLD) polymer films

Pigment-grade anatase TiO₂ particles (160 nm) were passivated using ultra-thin insulating films deposited by molecular layer deposition (MLD). Trimethylaluminum (TMA) and ethylene glycol (E.G) were used as aluminum alkoxide (alucone) precursors in the temperature range of 100–160 °C. The growth rate varied from 0.5 nm/cycle at 100 °C to 0.35 nm/cycle at 160 °C. Methylene blue oxidation tests indicated that the photoactivity of pigment-grade TiO₂ particles was quenched after 20 cycles of alucone MLD film, which was comparable to 70 cycles of Al₂O₃ film deposited by atomic layer deposition (ALD). Alucone films would decompose in the presence of water at room temperature and would form a more stable composite containing aluminum, which decreased the passivation effect on the photoactivity of TiO₂ particles.     

The synthesis of graphene-TiO<Subscript>2</Subscript>/g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> super-thin heterojunctions with enhanced visible-light photocatalytic activities

In this paper, an efficient strategy for the synthesis of graphene nanobelt-titanium dioxide/graphitic carbon nitride (graphene-TiO₂/g-C₃N₄) heterostructure photocatalyst was applied to fabricate a kind of visible-light-driven photocatalyst. The heterostructure shows higher absorption edge towards harvesting more solar energy compared with pure TiO₂ and pure g-C₃N₄ respectively. Furthermore, the as-prepared graphene-TiO₂/g-C₃N₄ heterostructure can show enhanced photocatalytic activity under visible-light irradiation. These outstanding performances of photocatalytic activities for graphene-TiO₂/g-C₃N₄ composites can be attributed to the heterojunction interfaces which can separate the electron-hole pairs and impede the recombination of electrons and holes more efficiently. This study conclusively demonstrates a facile and environmentally friendly new strategy to design highly efficient graphene-TiO₂/g-C₃N₄ heterostructure photocatalytic materials for potential applications under visible-light irradiation.

Open image in new window

Graphical abstract ?

     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Novel nanocomposite membranes based on polybenzimidazole and Fe<Subscript>2</Subscript>TiO<Subscript>5</Subscript> nanoparticles for proton exchange membrane fuel cells

In this work, Fe₂TiO₅ nanoparticles were used for improving the proton conductivity, and water and acid uptake of polybenzimidazole (PBI)-based proton exchange membranes. The nanocomposite membranes have been prepared using different amounts of Fe₂TiO₅ nanoparticles and dispersed into a PBI membrane with the solution-casting method. The prepared membranes were then physico-chemically and electrochemically characterized for use as electrolytes in high-temperature PEMFCs. The PBI/Fe₂TiO₅ membranes (PFT) showed a higher acid uptake and proton conductivity compared with the pure PBI membranes. The highest acid uptake (156 %) and proton conductivity (78 mS/cm at 180 °C) were observed for the PBI nanocomposite membranes containing 4 wt% of Fe₂TiO₅ nanoparticles (PFT₄). The PFT₄ composite membrane showed 380 mW/cm² power density and 760 mA/cm² current density in 0.5 V at 180 °C at dry condition. The above results indicated that the PFT₄ nanocomposite membranes could be utilized as proton exchange membranes for high-temperature fuel cells.     

Facial synthesis of carbon-coated ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene and their enhanced lithium storage properties

Carbon-coated ZnFe₂O₄ spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g^?1 and maintains a reversible capacity of 775 mAh g^?1 after 150 cycles at a current density of 500 mA g^?1. After being tested at 2 A g^?1 for 700 cycles, the capacity still retains 617 mAh g^?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe₂O₄ spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.

Open image in new window

Graphical abstract ?

     

EFFECT OF ZnFe22O4 DOPING ON THE OPTICAL PROPERTIES OF TiO2 THIN FILMS

Amorphous TiO₂ thin films and ZnFe₂O₄ doped TiO₂ composite films were deposited by radio frequency magnetron sputtering. The effect of ZnFe₂O₄ doping on the optical properties of TiO₂ thin films was reported. Our results show that the absorption edge of TiO₂ thin films and composite films exhibits a blue shift with decreasing annealing temperature. The absorption edge of composite films has moved to visible spectrum range, and a very large red shift occurs in comparison with TiO₂ thin film. An enhanced photoluminescence in ZnFe₂O₄ doped anatase TiO₂ thin film at room temperature.     

Observation of photoexcitation of Fe-oxide grown on TiO<Subscript>2</Subscript>(100) by visible light irradiation

Electronic excitation of materials is of fundamental and technological importance and interest in terms of photoinduced phase transition, photovoltaics, and photocatalysis. In the present study, photoexcitation of Fe₂ O ₃ epitaxially grown on rutile TiO₂(100) was investigated with conversion electron Mössbauer spectroscopy (CEMS) under dominantly visible-light irradiation. ⁵⁷Fe was deposited on the substrate at a substrate temperature of 973 K, and the resulting film was characterized by RHEED and XPS. After deposition of Fe on TiO₂(100), it was found that Fe was oxidized to Fe ³⁺, and the structure was analyzed to be the rhombohedral phase of Fe₂ O ₃. While the CEMS spectrum without light irradiation showed a quadrupole splitting of 0.80 mm/s with an isomer shift of +0.25 mm/s, an additional component with a quadrupole splitting of 0.85 and an isomer shift of +0.67 mm/s was observed under light irradiation. The latter component corresponds to a reduced state of Fe at the octahedral site surrounded by oxygen atoms. The lifetime of this photoexcited state is discussed.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.