Analysis of radial nonlocal effect on the structural response of carbon nanotubes

In this Letter, finite element model is developed to study the effect of nonlocal parameter in the radial structural response of carbon nanotubes. Timoshenko beam model is employed. The influence of nonlocal parameter in the radial direction due to interaction of atoms is defined as the radial nonlocal effect. It is found that there is significant influence of radial nonlocal effect on the structural response of the carbon nanotubes.     

Modeling and simulation for the field emission of carbon nanotubes array

To optimize the field emission of the infinite carbon nanotubes (CNTs) array on a planar cathode surface, the numerical simulation for the behavior of field emission with finite difference method was proposed. By solving the Laplace equation with computer, the influence of the intertube distance, the anode–cathode distance and the opened/capped CNT on the field emission of CNTs array were taken into account, and the results could accord well with the experiments. The simulated results proved that the field enhancement factor of individual CNT is largest, but the emission current density is little. Due to the enhanced screening of the electric field, the enhancement factor of CNTs array decreases with decreasing the intertube distance. From the simulation the field emission can be optimized when the intertube distance is close to the tube height. The anode–cathode distance hardly influences the field enhancement factor of CNTs array, but can low the threshold voltage by decreasing the anode–cathode distance. Finally, the distribution of potential of the capped CNTs array and the opened CNTs array was simulated, which the results showed that the distribution of potential can be influenced to some extent by the anode–cathode distance, especially at the apex of the capped CNTs array and the brim of the opened CNTs array. The opened CNTs array has larger field enhancement factor and can emit more current than the capped one.     

Magnetization of carbon nanotubes

For narrow-gap carbon nanotubes, the curvature effect due to the misorientation of 2p_z orbitals dominates over electronic structures and thus magnetic properties. It significantly changes magnetization and magnetic susceptibility, and creates special structures in them. There exists a critical field direction in changing magnetism. The critical angle strongly depends on the chiral angle, the nanotube radius, and the temperature. One-dimensional carbon nanotubes are quite different from zero-dimensional carbon tori, such as in terms of special structures in magnetization, the strength of the magnetic response, and the critical angle.     

Terahertz applications of carbon nanotubes

We formulate and justify several proposals utilizing unique electronic properties of carbon nanotubes for a broad range of applications to THz optoelectronics, including THz generation by hot electrons in quasi-metallic nanotubes, frequency multiplication in chiral-nanotube-based superlattices controlled by a transverse electric field, and THz radiation detection and emission by armchair nanotubes in a strong magnetic field.     

Synthesis and characterization of carbon nanotubes on carbon microfibers by floating catalyst method

In this paper, carbon nanotubes were synthesized on carbon microfibers by floating catalyst method with the pretreatment of carbon microfibers at the temperature of 1023 K, using C₂H₂ as carbon source and N₂ as carrier gas. The morphology and microstructure of carbon nanotubes were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). The composition of carbon nanotubes was determined by energy dispersive X-ray spectroscopy (EDX). The results showed that the surface of treated carbon microfibers was thickly covered by carbon nanotubes with diameters of about 50 nm. EDX image indicated that the composition of carbon nanotubes was carbon. In comparison with the sample grown on untreated carbon microfibers surface, it was found that after carbon microfibers were boiled in the solution of sulfur acid and nitric acid (VH₂SO₄:VHNO₃ = 1:3) and immersed in the solution of iron nitrate and xylene, carbon nanotubes with uniform density can be grown on carbon microfibers surface. Based on the results, we concluded that the pretreatment of carbon microfibers had great effect on the growth of carbon nanotubes by floating catalyst method.     

One-step preparation of water-soluble single-walled carbon nanotubes

A novel one-step process using potassium persulfate (KPS) as oxidant is proposed in this paper to prepare water-soluble single-walled carbon nanotubes (SWNTs). The process without the need for organic solvents and acids is a low-cost, eco-friendly, facile method. Morphology observation by atomic force microscopy (AFM) indicates that the KPS-treated SWNTs were effectively debundled without obvious shortening in their length. The functional groups and thermal stability of the treated SWNTs were analyzed by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). XPS results show that several functional groups such as potassium carboxylate (-COOK), carbonyl (-CO) and hydroxyl (-C-OH) groups were formed on the surfaces of the SWNTs, while the TGA results reveal that the quantity of the functional groups can reach to approximately 20%.     

Functionalization of carbon nanotubes with silver clusters

In this paper, an advanced method of one-step functionalization of single and multi walled carbon nanotubes (SWCNTs and MWCNTs) using γ-irradiation was described. Two synthesis procedures, related with different reduction species, were employed. For the first time, poly(vinyl alcohol) PVA is successfully utilized as a source to reduce silver (Ag) metal ions without having any additional reducing agents to obtain Ag nanoparticles on CNTs. The decoration of carbon nanotubes with Ag nanoparticles takes place through anchoring of (PVA) on nanotube's surface. Optical properties of as-prepared samples and mechanism responsible for the functionalization of carbon nanotubes were investigated using UV-vis and FTIR spectroscopy, respectively. Decorated carbon nanotubes were visualized using microscopic techniques: transmission electron microscopy and scanning tunneling microscopy. Also, the presence of Ag on the nanotubes was confirmed using energy dispersive X-ray spectroscopy. This simple and effective method of making a carbon nanotube type of composites is of interest not only for an application in various areas of technology and biology, but for investigation of the potential of radiation technology for nanoengineering of materials.     

Damping of electron Zitterbewegung in carbon nanotubes

Zitterbewegung (ZB, trembling motion) of electrons in semiconductor carbon nanotubes is described taking into account dephasing processes. The density matrix formalism is used for the theory. Differences between decay of ZB oscillations due to electron localization and that due to dephasing are discussed.     

Investigation of electrical transport in hydrogenated multiwalled carbon nanotubes

Highly disordered multiwalled carbon nanotubes of large outer diameter (∼60 nm) fabricated by means of chemical vapor deposition process inside porous alumina templates exhibit ferromagnetism when annealed in a H₂/Ar atmosphere. In the presence of an applied magnetic field, there is a transition from positive to negative magnetoresistance. The transition may be explained in terms of the Bright model for ordered and disordered carbon structures. Additionally, temperature dependent electrical transport experiments exhibit a zero-bias anomaly at low temperature.     

碳纳米管负载矾的第一性原理研究

本文基于密度泛函第一性原理研究了原始和带有缺陷的(Stone-Wales缺陷和单空位缺陷)碳纳米管负载金属V的稳定构型.对于V吸附在原始碳纳米管(CNT)上时,V在内表面的吸附比外表面的吸附有更强的相互作用力,且六元环内表面结构最稳定.当V与Stone-Wales缺陷碳纳米管相互作用时,V原子易吸附在管外七元环C-C键的外表面和内表面处,这说明缺陷位置的有效结合使之局域化加强.而以单空位缺陷碳纳米管为载体时V最易吸附在外缺陷处,相当于碳纳米管的一个C被金属V原子取代,形成了3个V-C_(sur)键,这进一步表明SV管外吸附比管内吸附更容易.我们从上述三种构型载体中发现,金属V吸附在缺陷碳纳米管时的稳定性要优于原始碳纳米管,且SV缺陷对金属V的固定效果最好.     

A detailed model for the flame synthesis of carbon nanotubes and nanofibers

Many experimental investigations of CNT/CNF flame synthesis have been recently reported. However, there are as yet no comprehensive models regarding their formation, growth or structure. Herein, a CNT/CNF growth rate model is proposed that is applicable for any method of CNT/CNF production (although our particular interest lies in flame synthesis in ethylene/air flames). While it is usual for most existing models to consider only a single carbon-carrying gas that contributes towards carbon deposition, our extended model can consider a complex hydrocarbon mixture that can mimic a flame environment. The model shows that before carbon nucleation is initiated, the surface density of carbon atoms increases as they are added through diffusion from the leading face of the catalyst nanoparticle. Over time, the diffusion potential decreases due to a reduction in the carbon atom concentration gradient. However, with the onset of nucleation and growth, diffusion is reinstated as the major driving potential for carbon atom transport through the nanoparticle. Steady carbon deposition and filament growth occurs once there is a stable carbon cluster size due to nucleation. The results support our hypothesis that flame synthesis can be a much faster and higher throughput process than CVD. The CNT/CNF growth rate decreases with increasing height above the burner. Decreasing temperature at higher locations leads to slower catalyst deactivation, but the CO concentration, which is the major contributor to carbon deposition, also decreases with increasing height above the burner. One of the major findings in this work is the contribution of CO to CNT formation by flame synthesis. The concentration of hydrocarbons in the vicinity of the toroidal zone near, which most of the CNT growth is observed, is negligible compared to CO concentration. Our results provide a basis to conduct future multiscale simulations of CNT/CNF growth.     

Biological functionalization and fluorescent imaging of carbon nanotubes

Biofunctionalization and manipulating of carbon nanotubes (CNTs) is important for biomedical research and application. Cy5 labeled goat anti-rabbit IgG (anti-IgG-Cy5) is chemically bonded to CNTs via a two-step process of diimide-activated amidation. This process can avoid the intermolecular connection of proteins. Fluorescent imaging of CNTs in aqueous solution has been demonstrated using anti-IgG-Cy5 immobilized CNTs (IgG-CNTs) as the model. The biologically functionalized carbon nanotubes (f-CNTs) in solution have been observed successfully using fluorescence microscopy. The fluorescent image of highly oriented f-CNTs is obtained at first time. The influencing factors on fluorescent imaging including oxidation duration, background noise and reactant concentration are discussed.     

碳纳米管在储氢上的应用

氢能是一种理想的能源载体,而经济有效的储氢手段是氢能实现规模应用急需解决的关键问题之一。碳纳米管在存储氢气上表现出来的独特性质,使其最有希望成为一种新的高效的储氢材料。从实验、理论研究两个方面总结了前人在碳纳米管储氢上的研究成果,并对碳纳米管储氢吸附方式,吸附量影响因素等方面做出分析。最后指出为实现碳纳米管储氢大规模应用仍需做的一些基础性研究工作。     

Preparation of carbon nanosheets deposited on carbon nanotubes by microwave plasma-enhanced chemical vapor deposition method

Carbon nanosheets were synthesized by microwave plasma-enhanced chemical vapor deposition method on carbon nanotubes substrate which was treated by hydrogen plasma. The results showed that the diameters of carbon nanotubes first got thick and then “petal-like” carbon nanosheets were grown on the outer wall of carbon nanotubes. The diameters of carbon nanotubes without and with carbon nanosheets were 100-150 and 300-500 nm, respectively. Raman spectrum indicated the graphite structure of carbon nanotubes/carbon nanosheets. The hydrogen plasma treatment and reaction time greatly affected the growth and density of carbon nanosheets. Based on above results, carbon nanosheets/carbon nanotubes probably have important applications as cold cathode materials and electrode materials.     

Thermal treatment of the carbon nanotubes and their functionalization with styrene

In this work we studied the functionalization of commercially available multiwalled carbon nanotubes (MWCNT) (Nanocyl 3100) with polystyrene by the method so called “grafting from”. The nanotubes were used as received and oxidized in air at 400 °C. The functionalization was started using thionyl chloride under reflux, followed by a reaction with ethylene glycol which allowed the inclusion of hydroxyl groups. The reaction of those with 2-chloropropionyl chloride led to the generation of the polymerization initiator. Last, the radical polymerization of the functionalized nanotubes, using styrene as the monomer, led to new materials which were studied with thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM) and ultraviolet–visible (UV–vis) spectroscopy.     

Effect of Pt and Fe catalysts in the transformation of carbon black into carbon nanotubes

In this research carbon nanotubes and carbon nano onion-like structures were synthesized from carbon black using metal catalysts at 400 °C and 700 °C. Platinum and iron-group metals were used as catalysts for the transformation of CB into graphitized nanocarbon and the effect of both metals was compared. The synthesized products were characterized using X-ray diffraction (XRD), transmission electron microscope (TEM), high resolution transmission electron microscope (HRTEM) and Raman spectroscopy. The characterization shows that this process is very efficient in the synthesis of high quality graphitized products from amorphous carbon black, even though the process temperature was relatively low in comparison with previous studies. Distinguished graphitic walls of the newly formed carbon nanostructures were clearly visible in the HRTEM images. Possible growth difference related to the type of catalyst used is briefly explained with the basis of electron vacancies in d-orbitals of metals.     

Optical studies of carbon nanotubes and nanographites

Resonance Raman and photoluminescence excitation (PLE) spectroscopies are used to study the optical properties of different types of carbon nanostructures such as carbon nanotube, nanoribbons, nanographites and graphite edges. In the resonance Raman experiments of carbon nanotubes, the (n,m) assignment is obtained by comparing the experimental and theoretical diameter and chirality dependence of the optical transitions. The influence of the environment on the optical transitions of the nanotubes is also obtained in the Raman experiments. The PLE measurements in different samples of carbon nanotubes show both direct and phonon-assisted optical transitions, and the results give new evidences that the optical transitions in nanotubes have an excitonic character, which is very strong for the low energy transitions. We also analyze the Raman spectra of nanoribbons and nanographites, showing that this technique is an important tool for defect characterization in graphitic materials, and can be used to distinguish the atomic structure of the graphite edges.     

A comparison between the mechanical and thermal properties of single-walled carbon nanotubes and boron nitride nanotubes

Carbon nanotubes (CNTs) are semimetallic while boron nitride nanotubes (BNNTs) are wide band gap insulators. Despite the discrepancy in their electrical properties, a comparison between the mechanical and thermal properties of CNTs and BNNTs has a significant research value for their potential applications. In this work, molecular dynamics simulations are performed to systematically investigate the mechanical and thermal properties of CNTs and BNNTs. The calculated Young’s modulus is about 1.1 TPa for CNTs and 0.72 TPa for BNNTs under axial compressions. The critical bucking strain and maximum stress are inversely proportional to both diameter and length-diameter ratio and CNTs are identified axially stiffer than BNNTs. Thermal conductivities of (10, 0) CNTs and (10, 0) BNNTs follow similar trends with respect to length and temperature and are lower than that of their two-dimensional counterparts, graphene nanoribbons (GNRs) and BN nanoribbons (BNNRs), respectively. As the temperature falls below 200 K (130 K) the thermal conductivity of BNNTs (BNNRs) is larger than that of CNTs (GNRs), while at higher temperature it is lower than the latter. In addition, thermal conductivities of a (10, 0) CNT and a (10, 0) BNNT are further studied and analyzed under various axial compressive strains. Low-frequency phonons which mainly come from flexure modes are believed to make dominant contribution to the thermal conductivity of CNTs and BNNTs.     

Catalyst influence on the flame synthesis of aligned carbon nanotubes and nanofibers

Since prepared substrates offer an appropriate method for the selective production of uniform arrays of aligned CNTs and CNFs, it is important to illustrate the influence of different catalysts on the resulting nanostructures. This investigation characterizes the activity of three catalysts—iron in alloyed form as stainless steel, nickel, and platinum—on carbon nanostructure formation under identical conditions in an ethylene/air nonpremixed flame. We have synthesized well-aligned multi-walled CNTs (on Ni) and CNFs (on stainless steel). The third transition metal Pt produces CNF structures of a different kind, and its activity has not been previously characterized in flames. The catalyst and gas-phase conditions leading to the formation of these different structures are discussed.     

Preparation and characterization of biocompatible magnetic carbon nanotubes

Magnetic carbon nanotubes consisting of multi-wall carbon nanotubes (MWNTs) core and Fe₃O₄ shell were successfully prepared by in situ thermal decomposition of Fe(acac)₃ or FeCl₃ or Fe(CO)₅ in 2-pyrrolidone containing acid treated MWNTs at 240 °C with the protection of nitrogen gas. The samples were characterized by TEM, XRD, SEAD, XPS and superconducting quantum interference device. Also, their biocompatibility was compared with naked carbon nanotubes. The results showed that after coated with Fe₃O₄ nanoparticles, the obtained magnetic carbon nanotubes show superparamagnetic characteristic at room temperature, and their blocking temperature is about 80 K. The magnetic properties of the nanotubes are relevant to the content of magnetic particles, increasing content of magnetic nanoparticles leads to higher blocking temperature and saturation magnetization. The results of antimicrobial activities to bacterial cells (Escherichia coli) showed that the MWNTs have antimicrobial activity, while the magnetic nanotubes are biocompatible even with a higher concentration than that of MWNTs.