Device linearity improvement and current enhancement utilizing high-to-low doping-channel FETs

We report device linearity improvement and current enhancement in both a heterostructure FET (HFET) and a camel-gate FET (CAMFET) using InGaAs/GaAs high-low and GaAs high-medium-low doped channels, respectively. In an HFET, a low doped GaAs layer was employed to build an excellent Schottky contact. In a GaAs CAMFET, a low doped layer together withn⁺andp⁺layers formed a high-performance majority camel-diode gate. Both exhibit high effective potential barriers of >1.0 V and gate-to-drain breakdown voltages of >20.0 V (atI_g=1.0 mA mm⁻¹). A thin, high doped channel was used to enhance current drivability and to improve the transconductance linearity. A 2×100 μm²HFET had a peak transconductance of 230 mS mm⁻¹and a current density greater than 800 mA mm⁻¹. The device had a transconductance of more than 80 percent of the peak value over a wide drain current range of 200 to 800 mA mm⁻¹. A 1.5×100 μm²CAMFET had a peak transconductance of 220 mS mm⁻¹and a current density greater than 800 mA mm⁻¹. Similarly, the device had a transconductance of more than 80 percent of the peak value over a wide drain current range of 160 to 800 mA mm⁻¹. The improvement of device linearity and the enhancement of current density suggest that high-to-low doped-channel devices for both an HFET and a CAMFET are suitable for high-power large signal circuit applications.     

AZO/Ag/AZO multilayer films prepared by DC magnetron sputtering for dye-sensitized solar cell application

Ag films were deposited on Al-doped ZnO (AZO) films and coated with AZO to fabricate AZO/Ag/AZO multilayer films by DC magnetron sputtering on glass substrates without heating of glass substrates. The best multilayer films have low sheet resistance of 19.8 Ω/Sq and average transmittance values of 61% in visible region. It was found that the highest figure of merit (F_TC) is 6.9 × 10⁻⁴ Ω⁻¹. For the dye-sensitized solar cell (DSSC) application, the multilayer films were used as transparent conductive electrode (multilayer films/ZnO + Eosin-Y/LiI + I₂/Pt/FTO). The best DSSC based on the multilayer films showed that open circuit voltage (V_oc) of 0.47 V, short circuit current density (J_sc) of 2.24 mA/cm², fill factor (FF) of 0.58 and incident photon-to-current conversion efficiency (η) of 0.61%. It was shown that the AZO/Ag/AZO multilayer films have potential for application in DSSC.     

Interfacial energies of carbon tetrabromide

The equilibrated grain boundary groove shapes for solid carbon tetrabromide (CTB) in equilibrium with its melt were directly observed by using a horizontal temperature gradient stage. From the observed grain boundary groove shapes, Gibbs–Thomson coefficient (Γ) and solid–liquid interfacial energy (σ_SL) and grain boundary energy (σ_gb) of CTB have been determined to be (7.88 ± 0.8) × 10⁻⁸ K m, (6.91 ± 1.04) × 10⁻³ J m⁻² and (13.43 ± 2.28) × 10⁻³ J m⁻², respectively. The ratio of thermal conductivity of equilibrated liquid phase to solid phase for CTB has also been measured to be 0.90 at its melting temperature. The value of σ_SL for CTB obtained in present work was compared with the values of σ_SL determined in the previous works for same material and it was seen that the present result is in good agreement with previous works.     

A Boubaker polynomials expansion scheme (BPES)-related protocol for measuring sprayed thin films thermal characteristics

Measurements of In₂S₃ and ZnIn₂S₄ sprayed thin films thermal characteristics have been carried out using the photodetection technique. The thermal conductivity k and diffusivity D were obtained using a new protocol based on photothermal signal parameters analysis. Measured values of k and D were respectively, (15.2 ± 0.85) W m⁻¹K⁻¹ and (69.8 ± 7.1) × 10⁻⁶ m²s⁻¹ for In₂S₃, (7.2 ± 0.7) W m⁻¹K⁻¹ and (32.7 ± 4.3) × 10⁻⁶ m²s⁻¹ for ZnIn₂S₄. These values are extremely important since similar compounds are more and more proposed as Cd-free alternative materials for solar cells buffer layers.     

Utilization of surface plasmon resonance of Au/Pt nanoparticles for highly photosensitive ZnO nanorods network based plasmon field effect transistor

Hydrothermally processed highly photosensitive ZnO nanorods based plasmon field effect transistors (PFETs) have been demonstrated utilizing the surface plasmon resonance coupling of Au and Pt nanoparticles at Au/Pt and ZnO interface. A significantly enhanced photocurrent was observed due to the plasmonic effect of the metal nanoparticles (NPs). The Pt coated PFETs showed I_on/I_off ratio more than 3 × 10⁴ under the dark condition, with field-effect mobility of 26 cm² V⁻¹ s⁻¹ and threshold voltage of −2.7 V. Moreover, under the illumination of UV light (λ = 350 nm) the PFET revealed photocurrent gain of 10⁵ under off-state (−5 V) of operation. Additionally, the electrical performance of PFETs was investigated in detail on the basis of charge transfer at metal/ZnO interface. The ZnO nanorods growth temperature was preserved at 110 °C which allowed a low temperature, economical and simple method to develop highly photosensitive ZnO nanorods network based PFETs for large scale production.     

Effects of compositions on properties of PEO–KI–I2 salts polymer electrolytes for DSSC

The effects of compositions on properties of PEO/KI/I₂ salts polymer electrolytes were investigated to optimize the photovoltaic performance of solid state DSSCs. XRD pattern for the mole ratio 12:1 of [EO:KI] was showed the formation of complete amorphous complex. DSC results also confirmed the amorphous nature of the polymer electrolyte. The highest value of ionic conductivity is 8.36 × 10^− 5 S/cm at 303 K (ambient temperature) and 2.32 × 10^− 4 S/cm at 333 K (moderate temperature) for the mole ratio 12:1 of EO:KI complex. The effect of contribution of [I⁻] and [I₃⁻] concentration with conductivity were also evaluated. FTIR spectrum reveals that the alkali metal cations were co-ordinated to ether oxygen of PEO. The formation of polyiodide ions, such as symmetric I₃⁻ (114 cm^− 1) and I₅⁻ (145 cm^− 1) caused by the addition of iodine was confirmed by FT Raman spectroscopic measurements. The optimum composition of PEO–KI–I₂ polymer electrolyte system for higher conductivity at ambient and moderate temperatures was reported. A linear Arrhenius type behaviour was observed for all the PEO–KI polymer complexes. Transport number measurements were carried out for several polymer electrolyte compositions. Dye-sensitized solar cells were fabricated by using higher conductivity polymer electrolyte compositions and its photoelectrochemical performance was investigated. The fill factor, short-circuit current, photovoltage and energy conversion efficiency of the DSSC assembled with optimized electrolyte composition were calculated to be 0.563, 6.124 mA/cm², 593 mV and 2.044% respectively.     

Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Effect of series resistance on the performance of silicon Schottky diode in the presence of tin oxide layer

The current–voltage (I–V) characteristics of Al/SnO₂/p-Si (MIS) Schottky diodes prepared by means of spray deposition method have been measured at 80, 295 and 350 K. In order to interpret the experimentally observed non-ideal Al/SnO₂/p-Si Schottky diode parameters such as, the series resistance R_s, barrier height Φ_B and ideality factor n, a novel calculation method has been reported by taking into account the applied voltage drop across interfacial oxide layer V_i and ideality factor n in the current transport mechanism. The values obtained for V_i were subtracted from the applied voltage values V and then the values of R_s were recalculated. The parameters obtained by accounting for the voltage drop V_i have been compared with those obtained without considering the above voltage drop. It is shown that the values of R_s estimated from Cheung’s method were strongly temperature-dependent and decreased with increasing temperature. It is shown that the voltage drop across the interfacial layer will increase the ideality factor and the voltage dependence of the I–V characteristics. The interface state density N_ss of the diodes has an exponential growth with bias towards the top of the valance band for each temperature; for example, from 2.37 × 10¹³ eV⁻¹ cm⁻² in 0.70−E_v eV to 7.47 × 10¹³ eV⁻¹ cm⁻² in 0.62−E_v eV for 295 K. The mean N_ss estimated from the I–V measurements decreased with increasing the temperature from 8.29 × 10¹³ to 2.20 × 10¹³ eV⁻¹ cm⁻².     

First principles study of the structure,electronic state and stability of AlnAsm− anions

Structural and electronic properties of semiconductor binary microclusters Al_nAs_m⁻ anions have been investigated using the B3LYP-DFT method in the ranges of n = 1,2 and m = 1–7. Full structural optimization, adiabatic electron affinities calculation and frequency analysis are performed with the basis of 6–311 + G(d). The charged-induced structural changes in these anions have been discussed. The strong As–As bond is also favored over Al–As bonds in the Al_nAs_m⁻ anions in comparison with corresponding neutral cluster. Among different AlAs_m⁻ and Al₂As_m⁻ (m = 1–7) anions, AlAs₄⁻ and Al₂As₃⁻ are most stable.     

Inorganic polymer phosphazene disulfide as cathode material for rechargeable lithium batteries

Novel inorganic network polymer phosphazene disulfide [(NPS₂)₃]_n was synthesized by a solution cross-link method. IR and element content analysis confirmed the polymer's molecular structure. The polymer has an average particle size of d_0.5 = 7.7 μm and the specific surface area is 57.4 m² g^− 1. TG/DTA analysis showed that [(NPS₂)₃]_n underwent a decomposition reaction from 200 to 300 °C. When used as cathode material in lithium batteries, its initial discharge capacity was 459.1 mAh g^− 1, which is almost 93.5% of theoretical specific capacity (490.9 mAh g^− 1). After 30 charge–discharge cycles, the discharge capacity of [(NPS₂)₃]_n stabilized at approximately 400.1 mAh g^− 1 which revealed an excellent cyclic ability. Therefore [(NPS₂)₃]_n is of great potential as cathode material for secondary lithium batteries.     

Structural,XPS and impedance analysis of LixCoVO4 (x = 0.8, 1.0, 1.2)

Lithium cobalt vanadate Li_xCoVO₄ (x = 0.8; 1.0; 1.2) has been prepared by a solid state reaction method. The XRD analysis confirms the formation of the sample. A new peak has been observed for Li_1.0CoVO₄ and for Li_1.2CoVO₄ indicating the formation of a new phase. The XPS analysis indicates the reduction in the oxidation of vanadium and oxygen with the addition of Li in Li_xCoVO₄ (x = 0.8, 1.0, 1.2). The impedance analysis gives the conductivity value as 2.46 × 10^− 5, 6.16 × 10^− 5, 9 × 10^− 5 Ω^− 1 cm^− 1 for Li_xCoVO₄ (x = 0.8; 1.0; 1.2), all at 623 K. The similarity in the bulk activation energy (E_a) and the activation enthalpy for migration of ions (E_ω) indicate that the conduction in Li_1.2CoVO₄ has been due to hopping mechanism.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

On the step-graded doped-channel (SGDC) field-effect transistor

An i-InGaP/n-In_xGa_1 − xAs/i- GaAs step-graded doped-channel field-effect transistor (SGDCFET) has been fabricated and studied. Due to the existence of a V-shaped energy band formed by the step-graded structure, a large output current density, a large gate voltage swing with high average transconductance, and a high breakdown voltage can be expected. In this study, first, a theoretical model and a transfer matrix technique are employed to analyze the energy states and wavefunctions in the step-graded quantum wells. Experimentally, for a 1  ×  80 μm²gate dimension device, a maximum drain saturation current density of 830 mAmm ^− 1, a maximum transconductance of 188mSmm ^− 1 , a high gate breakdown voltage of 34 V, and a large gate voltage swing 3.3 V with transconductance larger than 150 mSmm ^− 1are achieved. These performances show that the device studied has a good potentiality for high-speed, high-power, and large input signal circuit applications.     

High room-temperature pyroelectric response of MgO-modified Pb0.99(Zr0.95Ti0.05)0.98Nb0.02O3 ceramics

The dielectric and pyroelectric responses of MgO-modified Pb_0.99(Zr_0.95Ti_0.05)_0.98Nb_0.02O₃ ceramics were investigated near F_R(LT)–F_R(HT) phase transition. It was found that MgO additive reduced the F_R(LT)–F_R(HT) phase transition temperature from 41 °C to room temperature (24 °C). Superior room-temperature pyroelectric properties were obtained in the composition of 0.10 wt% MgO addition without DC bias. The largest pyroelectric coefficient, 65 × 10⁻⁸ C cm⁻² K⁻¹, was detected. Accordingly, the detectivity figures of merit F_d had maximum values of 20 × 10⁻⁵ Pa^−1/2, and especially the voltage responsivity F_v = 0.91 m²C⁻¹ is the highest value reported so far among all pyroelectric materials. It shows promising potential for application in uncooled pyroelectric infrared detector.     

Thermal and sonochemical synthesis of porous (Ce,Zr)O2 mixed oxides from metal β-diketonate precursors and their catalytic activity in wet air oxidation process of formic acid

Porous (Ce_0.5Zr_0.5)O₂ solid solutions were prepared by thermolysis (T = 285 °C) or sonolysis (20 kHz, I = 32 W cm⁻², P_ac = 0.46 W mL⁻¹, T = 200 °C) of Ce(III) and Zr(IV) acetylacetonates in oleylamine or hexadecylamine under argon followed by heat treatment of the precipitates obtained in air at 450 °C. Transmission Electron Microscopy images of the samples show nanoparticles of ca. 4–6 nm for the two synthetic approaches. The powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and μ-Raman spectroscopy of solids obtained after heat treatment indicate the formation of (Ce_0.5Zr_0.5)O₂ solid solutions with a metastable tetragonal crystal structure for the two synthetic routes. The specific surface area of the samples varies between 78 and 149 m² g⁻¹ depending on synthesis conditions. The use of Barrett–Joyner–Halenda and t-plot methods reveal the formation of mixed oxides with a hybrid morphology that combines mesoporosity and microporosity regardless of the method of preparation. Platinum nanoparticles were deposited on the surface of the mixed oxides by sonochemical reduction of Pt(IV). It was found that the materials prepared by sonochemistry exhibit better resistance to dissolution during the deposition process of platinum. X-ray photoelectron spectroscopy analysis shows the presence of Pt(0) and Pt(II) on the surface of mixed oxides. Porous (Ce_0.5Zr_0.5)O₂ mixed oxides loaded with 1.5 %wt. platinum exhibit high activity in catalytic wet air oxidation of formic acid at 40 °C.     

Investigation of a graded channel InGaAs/GaAs heterostructure transistor

An InGaAS/GaAs heterostructure transistor utilizing a gradedIn_xGa_1 − xAs channel grown by low-pressure metal-olorganic chemical vapor deposition has been demonstrated. A negative differential resistance (NDR) phenomenon is observed. Electron mobilities are significantly improved by using the graded InGaAs channel. For the In composition varying fromx =  0.25 (at the buffer–channel interface) to x =  0.1 (at the spacer–channel interface) structure, a peak extrinsic transconductance of 24.6 S mm ^− 1(atV_DS =  6.5 V,V_GSstep =  − 0.5 mV) and a saturation current density as high as 555 mA mm ^− 1for a gate length of 1.5 μ m are obtained.     

Rapid synthesis of LiCr0.15Mn1.85O4 by glycine–nitrate method

LiCr_0.15Mn_1.85O₄ spinel has been successfully synthesized by glycine–nitrate method (GNM). The presence of pure spinel phase was confirmed by long term XRPD measurements and the Rietveld structural refinement. Lattice parameter was estimated to be 8.2338 Å. Average particle size of prepared powder material is below 500 nm. The BET surface area is 9.6 m² g^− 1. As a cathode material for lithium batteries LiCr_0.15Mn_1.85O₄ shows initial discharge capacity of 110 mA h g^− 1 and capacity retention of 83% after 50 cycles.     

Transparent CdO/n-GaN(0001) heterojunction for optoelectronic applications

Undoped CdO films were prepared by sol–gel method. Transparent heterojunction diodes were fabricated by depositing n-type CdO films on the n-type GaN (0001) substrate. Current–voltage (I–V) measurements of the device were evaluated, and the results indicated a non-ideal rectifying characteristic with I_F/I_R value as high as 1.17×10³ at 2 V, low leakage current of 4.88×10⁻⁶ A and a turn-on voltage of about 0.7 V. From the optical data, the optical band gaps for the CdO film and GaN were calculated to be 2.30 eV and 3.309 eV, respectively. It is evaluated that interband transition in the film is provided by the direct allowed transition. The n-GaN (0001)/CdO heterojunction device has an optical transmission of 50–70% from 500 nm to 800 nm wavelength range.     

Trapping of metastable high-spin species and weak cooperativity in a mononuclear Fe(II) spin-crossover system

The magnetic and structural properties of three gradual spin transition monomeric compounds based on the cation [Fe(Hpt)₃]²⁺ (Hpt=3-(pyrid-2-yl)-1,2,4-triazole) are presented. The non-cooperative character of the spin-crossover in [Fe(Hpt)₃](BF₄)₂·2H₂O (I) is evaluated in light of its calorimetric properties, which yielded the thermodynamic values Δ_trsH=5.81 kJ mol⁻¹ and Δ_trsS=39.5 J mol⁻¹ K⁻¹. The light-induced excited spin-state trapping effect is performed on [Fe(Hpt)₃](BF₄)₂·2H₂O (I) and [Fe(Hpt)₃](SO₄)_0.4(BF₄)_1.2·3H₂O (II), and the subsequent HS→LS relaxations are studied. Their merely first-order kinetics are affected by disorder in the structure of both complexes, which appears in the presence of a distribution of activation energies. HS species can also be frozen-in in I by rapid cooling. Continuous irradiation is shown to induce only apparent light-induced thermal hysteresis effect in I and II, stemming from slow kinetics of relaxation with respect to the kinetics of measurement.