A novel screen-printed electrode array for rapid high-throughput detection

A novel multi-channel electrode array sensing device was fabricated by screen-printing techniques using 96-well plate as the template. To confirm its practical value, we developed a one-step preparation of multi-walled carbon nanotubes (MWCNTs) doped electrode array by an ink containing MWCNTs, which was applied to the simultaneous detection of a variety of biological samples and environmental pollutants. Results demonstrated that the designed sensing device could carry out the multiple measurements of different analytes at the same time, while MWCNTs enhanced the electrocatalytic activity of electrodes toward electroactive molecules. The required amount of each sample was only ～200 μL. Moreover, the excellent differential pulse voltammetric (DPV) response toward dopamine, hydroquinone and catechol was obtained and the detection limits was determined to be 0.337, 0.289 and 0.369 μM, respectively. Comparing it with the traditional screen-printed electrode (SPE), this sensing device possesses the advantages of high-throughput, fast electron transfer rate for electrodes, short-time analysis and low sample consumption.     

Single-frequency impedance analysis of biofunctionalized dendrimer-encapsulated Pt nanoparticles-modified screen-printed electrode for biomolecular detection

We report the fabrication of polyamidoamine (PAMAM) dendrimer with 128 carboxyl group-encapsulated Pt nanoparticle-modified screen-printed carbon electrode, as an impedimetric biosensor, for the quantitative detection of human cardiac biomarker troponin-I (cTnI). PAMAM-Pt was electrochemically deposited over SPCE and its 128 terminal carboxyl groups were used as anchors for the site-specific biomolecular immobilization of protein antibody, anti-cTnI. The biosensor was characterized by contact angle measurements, transmission electron microscopy, UV-visible spectroscopy, and electrochemical techniques. A single-frequency impedance analysis study was utilized for the biomolecular sensing by monitoring the changes in the phase angle obtained at an optimized frequency resulting from antigen-antibody interactions. An optimized frequency of 100 Hz was obtained at which maximum changes in the phase angle were observed after immunoreactions for a given concentration of analyte. A concentration-dependent increase in the phase angle of the biosensor was observed with increasing cTnI concentration in the range of 1 pg mL^?1 to 100 ng mL^?1. Based on the concentration response data, the dissociation constant was found to be 0.51 pM reflecting high affinity of biosensor towards cTnI analyte arising due to high anti-cTnI loading with a better probe orientation on the 3-dimensional PAMAM-Pt structure.     

Carbon black: a promising electrode material for sodium-ion batteries

The reactions of sodium with non-porous carbon blacks have been studied. These materials show a high reversible capacity in sodium-ion batteries. The presence of disordered layers and the low density of the carbon black materials favor the reversibility of the process. A maximum amount of 0.0155 mole of sodium by cm³ of carbon is achieved. The performance of a sodium-ion cell using Na_0.7CoO₂ as the positive electrode and carbon black as the negative is described.     

Biomolecule-free,selective detection of clenbuterol based on disposable screen-printed carbon electrode

We report here the development of a selective clenbuterol sensor made of disposable screen-printed carbon electrode (SPCE) without the need of adding any biorecognition element. Good analytical performance was achieved through the proper function of both the oxygen functionalities and edge plane sites on the “preanodized” SPCE (SPCE*). It is the amino group of clenbuterol to effectively form hydrogen bond with the SPCE* to induce the adsorption of clenbuterol. The edge plane sites enhance the electron transfer process and further help the dimer formation of clenbuterol to generate electroactivity for analysis. Square wave voltammetry was applied to increase the detection sensitivity with a linear response in the range of 7–1000 ppb and a detection limit of 0.51 ppb (S/N = 3). In the real sample analysis, results observed were satisfactory with meat, human blood, and human urine. High reproducibility in sensor fabrication further favors the disposable purpose of applications.     

Carbon nanofiber electrode array for the detection of lead

A nanoelectrode array of vertically aligned carbon nanofibers was evaluated for the detection of Pb^2 + by anodic stripping voltammetry. The achieved detection limit of 1.73 nM is well below the environmental guidelines. The approach provides a safer alternative to the mercury electrodes commonly used for the detection of heavy metals.     

OH functionalized Multi-Walled Carbon Nanotube modified electrode as electrochemical sensor for the detection of Aceclofenac

ABSTRACT

The rapid electrochemical determination of Aceclofenac (ACF) has been employed by cyclic voltammetry (CV), differential pulse voltammetry (DPV) using developed OH-functionalised multiwalled carbon nanotube carbon paste electrode (OH-MWCNT/CPE). Modified electrode was characterised by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDAX), X-ray diffraction spectroscopy (XRD), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The ACF exhibits two oxidation peaks at +0.4 V, +0.66 V and one reduction peak at +0.3 V. The active surface area of the bare carbon paste electrode (BCPE) and modified electrode have been characterised by using K₃[Fe(CN)₆] solution containing 0.1 M KCl. In DPV mode, variation of ACF gave the limit of detection (LOD = 3s/m) 0.246 μM over the concentration range 1.0 to 190.0 μM (R² = 0.9994). The developed electrode has good stability, reproducibility and could be successfully validated for the detection of ACF in pharmaceutical samples and biological fluids.     

Electrochemical sensors based on antimony tin oxide-Prussian blue screen-printed electrode and PEDOT-Prussian blue for potassium ion detection

Journal of Solid State Electrochemistry - The development and analytical applications of electrochemical sensors based on antimony tin oxide (ATO)–Prussian blue (PB) screen-printed electrode...     

Quinoprotein glucose dehydrogenase modified carbon paste electrode for the detection of phenolic compounds

The development of an amperometric biosensor for the determination of phenolic compounds is described, using quinoprotein glucose dehydrogenase. The enzyme is integrated into carbon paste and its ability to donate electrons to oxidized phenolic compounds during glucose oxidation is exploited. The sensor response is based on electrochemical oxidation of the phenolic compound followed by its enzymatic regeneration when the bulk solution contains glucose and the electrode is potentiostated at +500 mV (vs. Ag/AgCl/0.1 mol/L KCl). As the result of the catalytic analyte regeneration the electrodes offer very sensitive measurements of redox species like p-aminophenol and hydroquinone and catecholamines such as epinephrine, norepinephrine, and dopamine. The sensor performance is characterized for the different substrates. Highest sensitivity is achieved for p-aminophenol which could be determined at sub-nanomolar level.     

Coral reef-like zinc niobate nanostructures decorated functionalized carbon nanofiber as electrode modifier for detection of oxidative stress biomarker: 3-nitro-L-tyrosine

Oxidative stress can transform immunologic disorders to malignancy by enhancing the effect of pathogenic factors associated with adverse health problems. Biomarkers generated during oxidative stress are essential in assessing the in vivo condition of the cell for evaluating health and diagnosing the disease at an early stage, prognosis, benign and effectual drug development, and testing the drug efficacy. 3-Nitro-L-tyrosine is an oxidative stress biomarker produced from L-tyrosine through nitration mediated by active metabolites. Thus, precise detection of 3-NO₂-Tyr in the biological medium is significantly important to monitor the cell environment. Consequently, a novel electrochemical sensing platform had been designed using ZnNb₂O₆ nanostructures anchored f-CNF as a glassy carbon electrode modifier. The crystalline and structural features, morphology, and elemental composition of ZnNb₂O₆/f-CNF nanocomposite were keenly verified. The synchronic activation of ZnNb₂O₆/f-CNF nanocomposite for effective detection of 3-NO₂-Tyr is mainly due to the synergic effect between its counterparts. Accordingly, the fabricated sensor possesses a remarkably low limit of detection (0.021 μM) with a good linear range, and sensitivity is noted to be 7.745 μA/μM?cm?². The consistency of this sensor was evinced through real-time monitoring of 3-NO₂-Tyr in urine and saliva samples which is beneficial in monitoring the pathological situation.     

Rapid hydrolysis and electrochemical detection of trace carbofuran at a disposable heated screen-printed carbon electrode

A disposable heated screen-printed carbon electrode (HSPCE) is successfully fabricated. It demonstrates rapid responses to electrical heating and is easily elevated above the water boiling point by a high frequency alternating current. The temperature rise at the HSPCE was found to be strongly dependent on the square of the heating current and the electrode width. Carbofuran (CAF) could be rapidly hydrolyzed to carbofuran phenol at the HSPCE with raised temperature, and then determined at the same electrode at room temperature by differential potential voltammetry (DPV). The factors influencing the detection were examined, including pH, hydrolytic temperature and heating time. Under the optimum conditions, the detection linear range of CAF was from 4.0 x 10(-7) to 4.0 x 10(-4) mol L(-1) and the detection limit was 5.0 x 10(-8) mol L(-1) (S/N = 3). This method was successfully applied to the analysis of CAF residues in real samples (spiked water, soil and vegetables), and satisfactory recoveries were obtained.     

Disposable screen-printed electrode coupled with recombinant Drosophila melanogaster acetylcholinesterase and multiwalled carbon nanotubes for rapid detection of pesticides

Recombinant Drosophila melanogaster acetylcholinesterase (R-DmAChE), multiwalled carbon nanotubes (MWCNTs), and Prussian blue have been combined for development of a three-electrode biosensor with more rapid responses and higher stability than in our previous study. A new disposable screen-printed electrode (SPE) was developed for rapid detection of organophosphate and carbamate pesticides. After optimization, 10 microg MWCNT and 5 microL enzyme immobilization solution consisting of 0.2% glutaraldehyde, 0.1% Nafion, 0.2% bovine serum albumin, 0.1 g/L MWCNT, and 1.5 mU R-DmAChE were fixed on each of the R-DmAChE/MWCNT SPEs. The LOD of this biosensor was 0.5 microg/L for pesticide standards of dichlorvos (DDV) and carbofuran. The performance of this biosensor was tested for vegetable and water samples at various spiked levels, and good stability and sensitivity were found. The obtained recoveries were from 82.6 to 110.5% for DDV at levels of 0.5-5 microg/L and 73.4 to 118.4% for carbofuran at 1-10 microg/L in lake and sea water samples, demonstrating that the proposed approach is an alternative means for rapid detection of pesticide residues and contaminants in food safety and environmental monitoring.     

Sarcosine oxidase composite screen-printed electrode for sarcosine determination in biological samples

As the prostate cancer (PCa) progresses, sarcosine levels increase both in tumor cells and urine samples, suggesting that this metabolite measurements can help in the creation of non-invasive diagnostic methods for this disease. In this work, a biosensor device was developed for the quantification of sarcosine via electrochemical detection of H₂O₂ (at 0.6 V) generated from the catalyzed oxidation of sarcosine. The detection was carried out after the modification of carbon screen printed electrodes (SPEs) by immobilization of sarcosine oxidase (SOX) on the electrode surface. The strategies used herein included the activation of the carbon films by an electrochemical step and the formation of an NHS/EDAC layer to bond the enzyme to the electrode, the use of metallic or semiconductor nanoparticles layer previously or during the enzyme immobilization. In order to improve the sensor stability and selectivity a polymeric layer with extra enzyme content was further added. The proposed methodology for the detection of sarcosine allowed obtaining a limit of detection (LOD) of 16 nM, using a linear concentration range between 10 and 100 nM. The biosensor was successfully applied to the analysis of sarcosine in urine samples.     

Carbon black nanoparticles film electrode prepared by using substrate-induced deposition approach

A new type of carbon film electrode, composed of a thin layer of tightly packed carbon black (CB) nanoparticles deposited onto a gelatin-covered indium tin oxide/glass support using the surface-induced deposition (SID) approach, is presented. Some parameters of the novel SID method were optimized and the surface image and functionalization of the investigated carbon black film electrode (CBFE) was inspected by employing scanning electron microscopy and infrared spectroscopy. A cyclic voltammetry (CV) study was conducted in which the electron-transfer kinetics and CBFE interfacial characteristics were evaluated employing several selected reference redox systems, such as [Ru(NH₃)₆]^3+/2+, [Fe(CN)₆]^3−/4− and Fe^3+/2+ in aqueous, and ferrocene/ferrocenium in acetonitrile media. CV recordings were also performed in order to compare the electrochemical behavior of the CBFE with that of some well-known and established bare carbon-based electrodes. In order to confirm the validity of the CB film preparation method, the electroanalytical performance of the proposed CBFE was examined by carrying out linear sweep voltammetry of ascorbic acid (AA), anodic stripping square-wave voltammetry of Cu(II) in acidic medium, and amperometric measurements of hydrogen peroxide under flow injection conditions. The sensing characteristics of the novel carbon film electrode, demonstrated in this preliminary study, comprise: (i) a wide working potential window ranging from +1.0 to −1.3 V (depending on the solution pH), (ii) a wide applicable pH range (at least from 2 to 12), (iii) low voltammetric background (<5 μA cm⁻²), (iv) a satisfactory linear voltammetric and amperometric response (r² > 0.99) to various analytes, (v) good reproducibility (for example, r.s.d. of 2% in amperometric detection of H₂O₂ and r.s.d. of 8.5% for electrode-to-electrode CV runs), and (vi) stable and fast current response (at least 100 CV runs with negligible change in CV response). The main advantages of the proposed CBFE originate from the unique CB film formation procedure that enables fast, simple, inexpensive and non-toxic CBFE preparation, which can find application in advanced electrochemical devices and is suitable for mass production.     

Flow-through amperometric methods for detection of the bioactive compound quercetin: performance of glassy carbon and screen-printed carbon electrodes

Journal of Solid State Electrochemistry - Rapid methods using batch injection analysis (BIA) with amperometric detection were developed for the determination of quercetin extracted from the...     

A highly stable and sensitive chemically modified screen-printed electrode for sulfide analysis

We report here a highly stable and sensitive chemically modified screen-printed carbon electrode (CMSPE) for sulfide analysis. The CMSPE was prepared by first ion-exchanging ferricyanide into a Tosflex anion-exchange polymer and then sealing with a tetraethyl orthosilicate sol-gel layer. The sol-gel overlayer coating was crucial to stabilize the electron mediator (i.e., Fe(CN)₆³⁻) from leaching. The strong interaction between the oxy-hydroxy functional group of sol-gel and the hydrophilic sites of Tosflex makes the composite highly rigid to trap the ferricyanide mediator. An obvious electrocatalytic sulfide oxidation current signal at ∼0.20 V versus Ag/AgCl in pH 7 phosphate buffer solution was observed at the CMSPE. A linear calibration plot over a wide range of 0.1 μM to 1 mM with a slope of 5.6 nA/μM was obtained by flow injection analysis. The detection limit (S/N = 3) was 8.9 nM (i.e., 25.6 ppt). Practical utility of the system was applied to the determination of sulfide trapped from cigarette smoke and sulfide content in hot spring water.     

Novel 4-carboxyphenyl-grafted screen-printed electrode for trace Cu(II) determination

This paper reports the interest of 4-carboxyphenyl-grafted screen-printed electrodes (4-CP-SPEs) for trace Cu(II) measurement in water samples. These novel sensors were easily prepared via electrochemically reduction of the corresponding diazonium salt. Detection of Cu(II) was then achieved by immersing the grafted electrode into the sample solution for 10 min, followed by the electrochemical measurement of accumulated metallic ions.The efficiency of the Cu(II) adsorption at the grafted layer was clearly demonstrated. 4-CP-SPEs were able to detect and quantify Cu(II) as low as 5 × 10^?9 and 10^?8 M in a large ionic strength range. Moreover, no major interference of Pb(II) in the determination of Cu(II) is expected in natural water. Electrodes were finally successfully applied for Cu(II) determination in tap water and in estuarine water demonstrating the convenience of such sensors for environmental analysis.     

Pyrenebutanoate as a dynamic protein modifier for fluorometric detection in capillary zone electrophoresis

Pyrenebutanoate as the amphiphilic fluorescent compound is suggested as a buffer additive in capillary zone electrophoresis (CZE) for a dynamic modification of several protein samples. Using deuterium lamp UV excitation for the on-column fluorometric detection, minimum detectable amounts in the amol-range of the proteins sampled on the CZE capillary was achieved.     

Microchip capillary electrophoresis with a cellulose-DNA-modified screen-printed electrode for the analysis of neurotransmitters

A microfluidic chip based on capillary electrophoresis coupled with a cellulose-single-stranded DNA (cellulose-ssDNA) modified electrode was used for the simultaneous analysis of dopamine (DA), norepinephrine (NE), 3,4-dihydroxy-L-phenylalanine (L-DOPA), 3,4-dihydroxyphenylacetic acid (DOPAC), and ascorbic acid (AA). The modification of the electrode improved the electrophoretic analysis performance by lowering the detection potential and enhancing the signal-to-noise characteristic without surface poisoning of the electrode. The sensitivity of the modified electrode was about 12 times higher than those of the bare ones. The test compounds were separated using a 62 mm long separation channel at the separation field strength of +200 V/cm within 220 s in a 10 mM phosphate buffer (pH 7.4). The most favorable potential for the amperometric detection was 0.7 V (vs. Ag/AgCl). A reproducible response (relative standard deviation of 1.3, 1.3, 2.1, 3.1, 3.4% for DA, NE, L-DOPA, DOPAC, and AA, respectively, for n = 9) for repetitive sample injections reflected the negligible electrode fouling at the cellulose-ssDNA modified electrode. Square-wave voltammetric analyses reflected the sensitivities of the modified electrode for DA, NE, L-DOPA, DOPAC, and AA which were 1.78, 0.82, 0.69, 2.45, and 1.23 nC/microM with detection limits of 0.032, 0.93, 1.13, 0.31, and 0.62 microM, respectively. The applicability of this microsystem to real sample analysis was demonstrated.