CMC/PNIPAAm半互穿网络水凝胶的溶胀动力学研究

以羧甲基纤维素钠(CMC)和N-异丙基丙烯酰胺(NIPAAm)为原料,制备了具有温度和pH敏感性的半互穿网络(CMC／PNIPAAmsemi-IPN)水凝胶,并研究了水凝胶在不同温度和pH值条件下的溶胀行为。结果表明：在弱碱性(pH-7．4)条件下,凝胶的溶胀速率和溶胀度都随着凝胶中CMC含量的增加而增大;而在酸性(pH-1．O)条件下则相反。在弱碱性条件下,水分子在凝胶中的扩散行为都可用non-Fickian扩散来描述,水分子在凝胶中的扩散系数D随着凝胶溶胀速率的增大而增大;在酸性条件下,20℃时凝胶的溶胀过程符合non-Fickian扩散规律,而37℃时凝胶的溶胀过程符合Fickian扩散规律,但水分子的扩散系数D相差不大。     

取代度和金属平衡离子对羧甲基纤维素热行为的影响

低取代度(DS<0.8)的NaCMC具有纤维素(Ⅱ)型的晶型结构,随DS增加结晶度迅速下降,DS>1时为无定形结构。其T_(?)随DS增加而降低,但DS=1.55的CMC的T_(?)则稍有提高。其起始分解温度(T_(?))随DS增加而增加,而分解活化能则与DS没有规律性的关系。CMC链上的平衡离子H~+、Na~+、Mg~+、Ca~+和Al~(3+)等对其结晶形态的破坏能力不同,对相同价数的离子,随离子半径增大,破坏力增强,而对半径相近的离子,高价的比低价的破坏作用明显。NaCMC的分解活化能E=251～293 kJ/mol,而高价平衡离子的CMC的E=105 kJ/mol左右。     

Swelling characteristics and application of gamma-radiation on irradiated SBR-carboxymethylcellulose (CMC) blends

Blends of styrene butadiene rubber (SBR) with varying loading degree from 60 wt% to 100 wt% of carboxymethylcellulose (CMC) have been prepared. Gamma radiation vulcanization of prepared blends was carried out with doses varying between 50 kGy and 250 kGy. Mechanical properties, namely, tensile strength (Ts), elongation at break (E_b) and hardness were followed up as a function of loading degree of CMC and gamma irradiation dose. Moreover, physical properties, specifically swelling number (SN) and gel fraction % (GF%) were undertaken. Results obtained showed an improvement in mechanical as well as in physical properties with increasing either CMC content or dose of irradiation. Thermal properties namely thermo gravimetric analysis (TGA) was carried out.     

高取代度阳离子淀粉的合成及其降滤失性能

高取代度阳离子淀粉的合成及其降滤失性能;环氧丙基三甲基氯化铵;阳离子淀粉;半干法;钻井液;降滤失剂     

分子模拟在超临界流体领域中的应用

"分子模拟作为一种全新的研究手段已经在化学、化工、材料、生物等领域受到了广泛的关注。特别是在超临界流体技术方面,其应用不但可以获得许多结构、传递以及热力学信息,而且可以部分取代昂贵的超临界实验。本文从超临界流体在主体相和受限空间中的特性以及超临界萃取、反应等几个方面对现有的分子模拟方法和成果进行总结与评述,并对进一步发展的方向和面临的困难进行了讨论。     

Swelling Resistance and Mechanical Performance of Physical Crosslink‐Based Poly(Vinyl Alcohol) Hydrogel Film with Various Molecular Weight

The present work aimed to develop polyvinyl alcohol (PVA) hydrogel films with physically crosslinking through controllable entanglement density of the polymer chains. The viscoelasticity of PVA aqueous solutions was investigated over a broad range in molecular weight. The chain length between the crosslinks in the hydrogel ( $\overline{M_e}$) and entanglement density was determined by the plateau modulus (G'). The value of ( $\overline{M_e}$) increased with the PVA molecular weight, which can be attributed to the enhanced entanglement associated with the hydrogen bonds between inter‐ and interchains. The melting and crystallization of the transparent PVA hydrogel films showed that the crystallinity was below 30%, which indicated that microcrystallites formed. Therefore, the entanglement effect and microcrystallization enhanced the stable crosslinked hydrogel network, which further improved by an increase in the molecular weight. Altogether, the PVA with the molecular weight higher than 88,000 g/mol can be envisioned as a promising material for preparing the hydrogel film possessing excellent performance. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1673–1683     

疏水改性低分子量阳离子聚丙烯酰胺抑制剂的制备及性能评价

针对现有阳离子类抑制剂与钻井液配伍性、抑制性较差的不足,本文以丙烯酰胺、甲基丙烯酰氧乙基三甲基氯化铵、丙烯酸十八酯为原料,以乙醇和乙酸丁酯的混合物作溶剂,采用沉淀聚合法,制备出了疏水改性低分子量阳离子聚丙烯酰胺BJX-1页岩抑制剂。通过研究不同反应条件对BJX-1分子量的影响规律,得出溶剂组成对BJX-1分子量影响最大,可通过调节溶剂组成实现BJX-1分子量的控制。当分子量为1.45×10~5g/mol~1.87×10~5g/mol时,BJX-1的抑制性最好,页岩岩屑120℃热滚回收率约为78%;增加BJX-1中疏水结构单元含量至2%~4%时,可进一步提高BJX-1抑制性,使页岩岩屑120℃热滚回收率高于90%;此时的最佳反应条件为:以乙醇和乙酸丁酯按体积比90∶10~100∶0组成的混合物作为溶剂,引发剂质量分数为0.1%,单体质量分数为3%,在80℃下反应7h。通过对比研究发现,当加量为1%时,BJX-1所对应的页岩岩屑120℃热滚回收率分别比常用小分子阳离子化合物JA-1和高分子量阳离子聚合物DY-1高27.85%和50.06%。BJX-1更能提高钻井液的综合流变性能,使钻井液流变性更加稳定,而且具有优良的高温高压降滤失性。     

Influence of Molecular Weight on Mild Steel Corrosion Inhibition Effect by Polyvinyl Alcohol in Hydrochloric Acid Solution

The corrosion inhibition of mild steel in hydrochloric acid solution in the presence of three different molecular weights of polyvinyl alcohol (PVA) designated as PVA-I, PVA-II, and PVA-III corresponding to 14,000, 72,000, and 125,000 g mol^?1, respectively, was investigated using electrochemical impedance spectroscopy, linear polarization resistance (LPR), and potentiodynamic polarization techniques at 25°C. It was found that PVA of different molecular weights inhibited the corrosion of mild steel in the acid environment. Inhibition efficiency (η%) increases with increase in concentration of the polymers. LPR measurements clearly show that inhibition efficiency increases with increasing molecular weight in the order PVA-III > PVA-II > PVA-I. Polarization curves indicate that PVA functions as a mixed inhibitor affecting both the anodic metal dissolution and cathodic hydrogen evolution partial reactions of the corrosion process. The experimental data obtained fitted well into Langmuir adsorption isotherm model. Physical adsorption mechanism is proposed from the thermodynamic (free energy of adsorption) parameters obtained.     

低场核磁共振法对油基钻井液乳状液乳滴稳定性的研究

采用低场核磁共振技术,针对油基钻井液油包水型乳状液乳滴的稳定性进行研究。引入弛豫试剂Mn Cl2·4H2O对W/Q型乳状液的T2分布曲线进行定性分析,位于10~1 000 ms之间的弛豫峰对应于中度可自由移动水和白油弛豫峰的叠合峰,定义为乳状液弛豫峰;1 000~10 000 ms之间的峰为高度可自由移动水的弛豫峰。基于此,以弛豫峰峰形为定性指标,弛豫峰面积比率和弛豫峰间距为定量指标,针对弛豫试剂、油水比和老化温度等因素对乳状液横向弛豫时间T2分布曲线的影响进行了分析,进而深入研究了其对油基钻井液乳状液乳滴稳定性的影响。还将低场核磁共振分析技术运用于油基钻井液乳状液体系相对含油率的测量。结果表明,低场核磁共振是一种高效、快捷、准确反映油基钻井液乳状液稳定性的分析测试技术,同时,还可用于油基钻井液乳状液或原油相对含油率的测量。     

The Influence of the Addition of Nuts on the Thermal and Rheological Properties of Wheat Flour

The aim of the study was to assess the influence of replacing wheat flour with hazelnuts or walnuts, in various amounts, on the thermal and rheological properties of the obtained systems. The research material were systems in which wheat flour was replaced with ground hazelnuts (H) or walnuts (W) in the amount of 5%, 10%, and 15%. The parameters of the thermodynamic gelatinization characteristics were determined by the differential scanning calorimetry method. In addition, the pasting characteristics were determined with the use of a viscosity analyzer and the viscoelastic properties were assessed. Sweep frequency and creep and recovery tests were used to assess the viscoelastic properties of the tested gels. It was found that replacing wheat flour with nuts increased the values of gelatinization temperature, gelatinization, and retrogradation enthalpy, and the degree of retrogradation. The highest viscosity was characteristic of the control sample (2039 mPa·s), and the lowest for the paste with 15% addition of walnuts (1120 mPa·s). Replacing the flour with nuts resulted in a very visible reduction in the viscosity of such systems. In addition, gels based on the systems with the addition of H and W were weak gels (tan δ = G″/G′ > 0.1), and the values of G′ and G″ parameters decreased with the increased share of nuts in the systems. Creep and recovery analysis indicated that the systems in which wheat flour was replaced with hazelnuts were less susceptible to deformation compared to the systems with the addition of W.     

Study on Rheologic Behavior and Molecular Configuration in the Mixed Systems of Polyacrylamide and Surfactants

Rheologic properties and the conformations of the mixed system of hydrophobically modified polyacrylamide and surfactants in distilled water with or without NaCl were investigated. The vacuum sublimation freezing-drying technique was employed to maintain the aggregation state of the mixed systems. Scan electron microscopy and transmission electron microscopy were used to investigate microstructure of the mixed systems formed, and obtain the system molecular configuration information. The results showed that the rheologic behavior of the mixed solution revealed by viscosity data and microconformation obtained depend on the salt existence and the hydrophobic group content of the polymer. The relationship between polymer microconformation and the macroscopic properties for the mixed systems was analyzed to explore the aggregating mechanism.     

Poly(L-lactide) Nano- and Microfibers by Electrospinning: Influence of Poly(L-lactide) Molecular Weight

Summary: The electrospinning technique based on single and multi-jet systems was applied for poly(L -lactide) (PLA) nano- and microfibers as well as fibrous mats manufacture; the latter with dimensions suitable for the tensile tests. The PLA's employed were prepared by the controlled ring-opening polymerization of the L,L -lactide (LA) monomer. The resulting fibers thickness was correlated with molecular weights of PLA's and viscosities of spinning solutions. The scanning electron microscopic, thermal, and tensile characteristics of the polymeric materials and fibrous mats were also examined.     

焙烧温度对SO42-改性锆交联粘土固体酸结构与催化活性的影响

用聚羟基锆离子交换Na基膨润土中的水合钠离子,再引入SO4^2-,在不同温度焙烧制备了锆交联粘土固体酸催化剂,利用XRD,IR,DTA等手段,对该催化剂的结构进行了分析测试,并以柠檬酸和正丁醇酯化反应为探针,考察了焙烧温度对其结构与催化活性的影响。实验结果表明,焙烧温度为500℃时,SO4^2-与锆氧化柱形成了具有超强酸性的结构,催化剂活性较佳,能使柠檬酸酯化反应转化率达96．6％,反应酯化率达95．72％。     

Voltammetric Determination of Low‐Molecular‐Weight Sulfur Compounds in Hydrothermal Vent Fluids – Studies with Hydrogen Sulfide,Methanethiol, Ethanethiol and Propanethiol

Determination of sulfide compounds in hydrothermal vent fluid samples was performed by DPCSV. The methodology was applied to speciate sulfides via primitive and first‐derivative curve interpretation. Hydrogen sulfide, methanethiol, and propanethiol were simultaneously assayed in samples containing no ethanethiol. In the presence of ethanethiol, the organic sulfides were determined without speciation. Sulfides were determined in an acidic electrolyte, and detection limits ranging from 0.1 to 1.1 μmol L^?1 were calculated. The method was tested in real hydrothermal vent fluid samples, with recoveries ranging from 86.9% (R–SH) to 115.3% (H₂S). Interference of the metallic species present in seawater was investigated.     

超高分子量聚乙烯基导电复合材料的电性能和自发热性能的研究

超高分子量聚乙烯(UHMWPE)具有优异的综合性能,本文采用凝胶结晶溶液方法制备了分别以碳纤维(CF)和镀镍碳纤维(NiCF)为导电填料,UHMWPE为基体的3个系列导电聚合物复合材料—UHMWPE/CF、UHMWPE/NiCF和UHMWPE/EMMA/CF复合体系,并分别对它们进行了室温伽马射线辐射处理,重点研究了这些材料的电性能和自发热性能,利用DSC、SEM、WAXS、DMA和体积膨胀等仪器进行了一系列测试表征。结果表明,NiCF作为导电填料时体系的逾渗阈值最低,为3vol%。伽马射线辐射处理不仅能有效提高材料的PTC效应,而且在合适的辐射剂量时也能有效提高材料的自发热性能。对材料介电性能的研究揭示了材料的交流电阻率与温度、频率的依赖关系。     

Characterizing the Diffusion and Rheological Properties of Aged Asphalt Binder Rejuvenated with Bio-Oil Based on Molecular Dynamic Simulations and Laboratory Experimentations

Soybean-derived bio-oil is one of the vegetable-based oils that is gaining the most interest for potential use in the rejuvenation of aged asphalt binders. This laboratory study was conducted to characterize and quantify the diffusion and rheological properties of bio-oil-rejuvenated aged asphalt binder (BRAA) using soybean oil. In the study, the chemical structure of the soybean oil was comparatively characterized using an element analyzer (EA), gel permeation chromatography (GPC), and a Fourier infrared (FTIR) spectrometer, respectively. Based on the chemical structure of the bio-oil, BRAA molecular models were built for computing the diffusion parameters using molecular dynamic simulations. Likewise, a dynamic shear rheometer (DSR) test device was used for measuring and quantifying the rheological properties of the aged asphalt binder rejuvenated with 0%, 1%, 2%, 3%, 4%, and 5% soybean oil, respectively. The laboratory test results indicate that bio-oil could potentially improve the diffusion coefficients and phase angle of the aged asphalt binder. Similarly, the corresponding decrease in the complex shear modulus has a positive effect on the low-temperature properties of BRAA. For a bio-oil dosage 4.0%, the diffusion coefficients of the BRAA components are 1.52 × 10⁻⁸, 1.33 × 10⁻⁸, 3.47 × 10⁻⁸, 4.82 × 10⁻⁸ and 3.92 × 10⁻⁸, respectively. Similarly, the corresponding reduction in the complex shear modulus from 1.27 × 10⁷ Pa to 4.0 × 10⁵ Pa suggests an improvement in the low-temperature properties of BRAA. Overall, the study contributes to the literature on the potential use of soybean-derived bio-oil as a rejuvenator of aged asphalt binders.     

Influence of Carbon Black and Silica Filler on the Rheological and Mechanical Properties of Natural Rubber Compound

Rubber compounds are reinforced with fillers such as carbon black and silica. In general, filled rubber compounds shows smooth rheological behavior and mechanical properties. Variation in rheological behavior and mechanical properties was studied in terms of the filler composition using natural rubber compounds filled with both carbon black and silica CB/Si = 0/60, 20/40, 30/30, 40/20 and 60/0 phr (parts per hundred rubber is parts of any non-rubbery material per hundred parts of raw gum elastomer (rubbery material)). The rheological behaviour can be showed in measurement of Mooney viscosity and cure time. The Mooney viscosity of rubber compounds increase with the increasing the carbon black in the compounds. The compound filled with CB/Si of 30/30 and 60/0 showed abnormal rheological behaviour in which the cure time decreased suddenly and the increased at certain ratio during the measurement. The mechanical properties such as hardness, abrasion resistance and tensile stress at 300% elongation were studied. In the hardness and abrasion resistance measurement, the higher ratio CB/Si decrease contribution of silica, which resulting smaller of hardness value. Ratio CB/Si 40/20 gives an optimum filler blended. It is also clearly understood that higher abrasion resistance mainly due to the lower hardness value under the same condition. The tensile stress at 300% elongation of rubber compound increased with the increasing carbon black filler.