Study of injection bias in a simple hydrodynamic injection in microchip CE

The electrokinetically pinched method is the most commonly used mode for sample injection in microchip capillary electrophoresis (microCE) due to its simplicity and well-defined sample volume. However, the limited injection volume and the electrophoretic bias of the pinched injection may limit its universal usage to specific applications. Several hydrodynamic injection methods in microCE have been reported; however, almost all claimed that their methods are bias-free without considering the dispensing bias. To investigate the dispensing bias, a simple hydrodynamic injection was developed in single-T and double-T glass microchips. The sample flow was produced by hydrostatic pressure generated by the liquid level difference between the sample reservoir and the other reservoirs. The reproducibility of peak area and peak area ratio was improved to a significant extent using large-surface reservoirs for the buffer reservoir and the sample waste reservoir to reduce the Laplace pressure effect. Without a voltage applied on the sample solution, the voltage-related sample bias was eliminated. The dispensing bias was analyzed theoretically and studied experimentally. It was demonstrated that the dispensing bias existed and could be reduced significantly by appropriately setting up the voltage configuration and by controlling the appropriate liquid level difference.     

Hydrodynamic injection with pneumatic valving for microchip electrophoresis with total analyte utilization

A novel hydrodynamic injector that is directly controlled by a pneumatic valve has been developed for reproducible microchip CE separations. The PDMS devices used for the evaluation comprise a separation channel, a side channel for sample introduction, and a pneumatic valve aligned at the intersection of the channels. A low pressure (≤ 3?psi) applied to the sample reservoir is sufficient to drive sample into the separation channel. The rapidly actuated pneumatic valve enables injection of discrete sample plugs as small as ~ 100?pL for CE separation. The injection volume can be easily controlled by adjusting the intersection geometry, the solution back pressure, and the valve actuation time. Sample injection could be reliably operated at different frequencies (< 0.1?Hz to > 2?Hz) with good reproducibility (peak height relative standard deviation ≤ 3.6%) and no sampling biases associated with the conventional electrokinetic injections. The separation channel was dynamically coated with a cationic polymer, and FITC-labeled amino acids were employed to evaluate the CE separation. Highly efficient (≥ 7.0 × 103 theoretical plates for the ~2.4-cm-long channel) and reproducible CE separations were obtained. The demonstrated method has numerous advantages compared with the conventional techniques, including repeatable and unbiased injections, little sample waste, high duty cycle, controllable injected sample volume, and fewer electrodes with no need for voltage switching. The prospects of implementing this injection method for coupling multidimensional separations for multiplexing CE separations and for sample-limited bioanalyses are discussed.     

Electrophoretic microchip with dual-opposite injection for simultaneous measurements of anions and cations

A novel dual-injection poly(methylmethacrylate) (PMMA) microchip electrophoretic system has been designed and fabricated for simultaneous measurements of anions and cations using a single channel and detection device. It consists of two sample reservoirs, on both sides of a common separation channel. Anions and cations can be simultaneously electrokinetically injected into both ends of the separation channel. Due to lower electroosmotic flow in polymer channels compared to glass ones, the cations and anions migrate in opposite directions and can be separated from each other and detected using a movable contactless conductivity detector (MCCD) positioned around the center of the separation channel. The effects of the detector position and of the separation voltage on the response and resolution have been studied and optimized for simultaneous determination of six low-energy explosive-related ions, including ammonium, methyl ammonium, sodium, chloride, nitrate, and perchlorate in a single analytical run (of ca. 3 min). Simultaneous detection of nerve-agent degradation products along with explosive-related anions and cations is also demonstrated. The versatile system can also be used for separately measuring anions or cations. The attractive behavior of the dual-opposite injection microchip offers great promise for a wide range of applications, including "total ion analysis" of various samples.     

Single potential electrophoresis microchip with reduced bias using pressure pulse injection

We propose two variants of a new injection technique for use in electrophoresis microchips, called "front gate pressure injection" and "back gate pressure injection", that both enable a controlled and reproducible sample introduction with reduced bias compared to electrokinetic gated injection. A continuous flow of a test solution of fluorescein/rhodamine B in 20 mM Tris/boric acid buffer (pH 8.6) sample test solution is electrokinetically driven near to the entrance of the separation channel, using a single voltage (3 kV) that is constant in time. A sample plug is injected in the separation channel by a pressure pulse of the order of 0.1 s. The latter is generated using the mechanical deflection of a PDMS membrane that is loosely placed on a dedicated chip reservoir. The analysis of the peak area ratio of the separated compounds demonstrates a nearly constant sample composition when using pressure-based injection. A small remaining injection bias for the shortest membrane deflection times can be attributed to a dilution effect of the charged compound due to the presence of an electrical field transverse to the sample flow boundary in the channel junction.     

Effects of the electric field distribution on microchip valving performance

Valving characteristics on microfluidic devices were controlled through manipulation of the electric field strengths during both the sample loading and dispensing steps. Three sample loading profiles for the constant volume valve (pinched injection) in conjunction with four dispensing schemes were investigated to study valving performance. The sample confinement profiles for the sample loading step consisted of a weakly pinched sample, a medium pinched sample, and a strongly pinched sample. Four dispensing schemes varied the electric field strengths in the sample and sample waste channels relative to the analysis channel to control the volume of the sample dispensed from the valve. The axial extent of the sample plug decreased as the electric field strengths in the sample and sample waste channels were raised relative to the analysis channel. In addition, a trade-off existed between sample plug length and sensitivity.     

Multiple enzyme linked immunosorbent assay system on a capillary-assembled microchip integrating valving and immuno-reaction functions

Gastrodin is a bioactive constituent of rhizome in Gastrodia elata Blume (Orchidaceae) The aim of this study is to develop a rapid and sensitive liquid chromatographic method coupled to microdialysis sampling system to measure the unbound of gastrodin in rat blood, brain and bile. Microdialysis probes were simultaneously inserted into the jugular vein, brain striatum and bile duct of each anesthetized rat for sampling after the administration of gastrodin (100 or 300 mg kg⁻¹) through the femoral vein. Separation of unbound gastrodin from various biological fluids was applied to an RP-select B column (250 mm × 4.6 mm i.d., 5 μm). The mobile phase consisted of acetonitrile–50 mM potassium dihydrogen phosphate buffer–triethylamine (5:95:0.1, v/v/v, adjusted to pH 2.5 with orthophosphoric acid) with a flow rate of 1 mL min⁻¹. The UV detector wavelength was set at 221 nm. Fifteen minutes after the administration, the gastrodin reached the peak concentration in brain and bile. In addition, the results indicate that gastrodin penetrates the blood-brain barrier (BBB) and goes through hepatobiliary excretion.     

Bias-free pneumatic sample injection in microchip electrophoresis

We have developed a new microfluidic chip capable of accurate metering, pneumatic sample injection, and subsequent electrophoretic separation. The pneumatic injection scheme, enabling us to introduce a solution without sampling bias unlike electrokinetic injection, is based upon the hydrophobicity and wettability of channel surfaces. An accurately metered solution of 10 nL could be injected by pneumatic pressure into a hydrophilic separation channel through Y-shaped hydrophobic valves, which consist of polydimethylsiloxane (PDMS) and fluorocarbon (FC) film layers. We demonstrated the successful pneumatic injection of a red ink solution into the separation channel as a proof of the concept. A mixture of fluorescein and dichlorofluorescein (DCF) could be baseline-separated using a single power source in microchip electrophoresis.     

Fabrication of a fiberglass-packed channel in a microchip for flow injection analysis

A novel fiberglass-packed channel in a microchip has been fabricated for flow injection analysis (FIA) based on the in situ polymerization of methyl methacrylate (MMA). MMA prepolymer molding solution containing an ultraviolet initiator was sandwiched between a poly(methyl methacrylate) (PMMA) cover plate and a PMMA base plate bearing a glycerol-permeated fiberglass bundle and exposed to UV light. During the UV-initiated polymerization, the fiberglass bundle was embedded in the PMMA substrate to form a fiberglass-packed microchannel. When the glycerol in the fiberglass bundle was flushed away with water, the obtained porous fiberglass-packed microchannel could serve as an electroosmotic pump and a FIA channel. Scanning electron micrographs offer insights into the fiber-based microchip. The analytical performance of the FIA system has been demonstrated by detecting catechol in connection with end-column amperometric detection. The fiber- based microchips can be fabricated by the new approach without the need for complicated and expensive lithography-based microfabrication techniques, indicating great promise for the low-cost production of microchips, and should find a wide range of applications.     

Sample transport and electrokinetic injection in a microchip device for chemical cytometry

Sample transport and electrokinetic injection bias are well characterized in capillary electrophoresis and simple microchips, but a thorough understanding of sample transport on devices combining electroosmosis, electrophoresis, and pressure-driven flow is lacking. In this work, we evaluate the effects of electric fields from 0 to 300 V/cm, electrophoretic mobilities from 10(-4) to 10(-6) cm(2)/Vs, and pressure-driven fluid velocities from 50 to 250 μm/s on sample injection in a microfluidic chemical cytometry device. By studying a continuous sample stream, we find that increasing electric field strength and electrophoretic mobility result in improved injection and that COMSOL simulations accurately predict sample transport. The effects of pressure-driven fluid velocity on injection are complex, and relative concentration values lie on a surface defined by pressure-driven flow rates. For high-mobility analytes, this surface is flat, and sample injection is robust despite fluctuations in flow rate. For lower mobility analytes, the surface becomes steeper, and injection depends strongly on pressure-driven flow. These results indicate generally that device design must account for analyte characteristics and specifically that this device is suited to high-mobility analytes. We demonstrate that for a suitable pair of peptides fluctuations in injection volume are correlated; electrokinetic injection bias is minimized; and electrophoretic separation is achieved.     

Sensitivity enhancing injection from a sample reservoir and channel interface in microchip electrophoresis

The stacking of a cationic analyte (i.e., rhodamine B) at the interface between a sample reservoir and channel in a microchip electrophoresis device is described for the first time. Stacking at negative polarity was by micelle to solvent stacking where the dye was prepared in a micellar solution (5 mM sodium dodecyl sulfate in 25 mM phosphoric acid, pH 2.5) and the channel was filled with high methanol content background solution (70% methanol in 50 mM phosphoric acid, pH 2.5). The injection of the stacked dye into the channel was by simple reversal of the voltage polarity with the sample solution and background solution at the anodic and cathodic reservoirs of the straight channel, respectively. The enrichment of rhodamine B at the interface and injection of the stacked dye into the channel was clearly visualized using an inverted fluorescence microscope. A notable sensitivity enhancement factor of up to 150 was achieved after 2 min at 1 kV of micelle to solvent stacking. The proposed technique will be useful as a concentration step for analyte mixtures in simple and classical cross‐channel microchip electrophoresis devices or for the controlled delivery of enriched reagents or analytes as narrow plugs in advanced microchip electrophoresis devices.     

Power-free sequential injection for microchip immunoassay toward point-of-care testing

This paper presents a simple fluid handling technique for microchip immunoassay. Necessary solutions were sequentially injected into a microchannel by air-evacuated poly(dimethylsiloxane), and were passively regulated by capillary force at the inlet opening. For heterogeneous immunoassay, microchips are potentially useful for reduction of sample consumption and assay time. However, most of the previously reported microchips have limitations in their use because of the needs for external power sources for fluid handling. In this paper, an on-chip heterogeneous immunofluorescence assay without such an external power source is demonstrated. The microchip consisting of poly(dimethylsiloxane) (PDMS) and glass has a simple structure, and therefore is suitable for single-use applications. Necessary solutions were sequentially injected into a microchannel in an autonomous fashion with the power-free pumping technique, which exploits the high solubility and the rapid diffusion of air in PDMS. For deionized water, this method yielded flow rates of 3-5 nL s-1 with reproducibility of 4-10%. The inlet opening of the microchannel functioned as a passive valve to hold the solution when the flow was finished. Rabbit immunoglobulin G (rIgG) and human C-reactive protein (CRP) were detected using the microchannel walls as reaction sites. With the sample consumption of 1 microL and the assay time of approximately 20 min including the antibody immobilization step, the sandwich immunoassay methods for rIgG and CRP exhibited the limits of detection of 0.21 nM (0.21 fmol) and 0.42 nM (0.42 fmol), respectively.     

Rapid serial analysis of multiple oligonucleotide samples on a microchip using optically-gated injection

Optically-gated injection of fluorescently-labeled DNA has been accomplished for the first time. Rapid, serial analysis of oligonucleotide ladders has been shown on a microchip using this injection technique. Separations of five- and six-component samples have been completed in 60 s or less with a capability to carry out serial injections of these samples every 15 s. The technique has been shown to have better than five base resolution for small oligonucleotides and excellent reproducibility in migration times (< or = 0.75% RSD). Currently, the limit of detection for the system is 0.23 microM. Additionally, multiple unique samples of DNA have been consecutively analyzed in a single separation lane using optical gating. Six consecutive injections of three different samples have been achieved with no sample carryover and a total analysis time of approximately 10 min. These results show the potential of optical gating as an alternative injection technique for high-throughput DNA applications, such as genotyping and monitoring dynamic processes.     

Pesticide analysis by MEKC on a microchip with hydrodynamic injection from organic extract

An integrated microchip for monitoring carbamate pesticides in environmental water using continuous flow chemical processes is under development, i. e., the integration of hydrolysis, azo-derivatization, liquid-liquid extraction, electrophoretic separation, and quantification. The separation of the derivatives of four carbamate pesticides (carbaryl, carbofuran, propoxur, and bendiocarb) extracted in the continuous flow of a 1-butanol phase was studied in a silica microchip using micellar EKC. A baseline separation of four pesticide derivatives was achieved on a silica chip using hydrodynamic injection with electroosmotic gating. Detection using a thermal lens microscope showed good linearity in the concentration range of 10(-6 )-10(-5 )M with an LOD of 5 x 10(-7) M, which is superior to that of conventional CE with UV absorption detection at a level of 10(-4) M.     

Further improvement of hydrostatic pressure sample injection for microchip electrophoresis

Hydrostatic pressure sample injection method is able to minimize the number of electrodes needed for a microchip electrophoresis process; however, it neither can be applied for electrophoretic DNA sizing, nor can be implemented on the widely used single-cross microchip. This paper presents an injector design that makes the hydrostatic pressure sample injection method suitable for DNA sizing. By introducing an assistant channel into the normal double-cross injector, a rugged DNA sample plug suitable for sizing can be successfully formed within the cross area during the sample loading. This paper also demonstrates that the hydrostatic pressure sample injection can be performed in the single-cross microchip by controlling the radial position of the detection point in the separation channel. Rhodamine 123 and its derivative as model sample were successfully separated.     

A minimally invasive microchip for transdermal injection/sampling applications

The design, fabrication, and characterization of a minimally invasive silicon microchip for transdermal injection/sampling applications are reported and discussed. The microchip exploits an array of silicon-dioxide hollow microneedles with density of one million needles cm(-2) and lateral size of a few micrometers, protruding from the front-side chip surface for one hundred micrometers, to inject/draw fluids into/from the skin. The microneedles are in connection with independent reservoirs grooved on the back-side of the chip. Insertion experiments of the microchip in skin-like polymers (agarose hydrogels with concentrations of 2% and 4% wt) demonstrate that the microneedles successfully withstand penetration without breaking, despite their high density and small size, according to theoretical predictions. Operation of the microchip with different liquids of biomedical interest (deionized water, NaCl solution, and d-glucose solution) at different differential pressures, in the range 10-100 kPa, highlights that the flow-rate through the microneedles is linearly dependent on the pressure-drop, despite the small section area (about 13 μm(2)) of the microneedle bore, and can be finely controlled from a few ml min(-1) up to tens of ml min(-1). Evaporation (at room temperature) and acceleration (up to 80 g) losses through the microneedles are also investigated to quantify the ability of the chip in storing liquids (drug to be delivered or collected fluid) in the reservoir, and result to be of the order of 70 nl min(-1) and 1300 nl min(-1), respectively, at atmospheric pressure and room temperature.     

Instrumentation design for hydrodynamic sample injection in microchip electrophoresis: A review

Reproducible and representative sample injection in microchip electrophoresis has been a bottleneck for quantitative analytical applications. Electrokinetic sample injection is the most used because it is easy to perform. However, this injection method is usually affected by sample composition and the bias effect. On the other hand, these drawbacks are overcome by the hydrodynamic (HD) sample injection, although this injection mode requires HD flow control. This review gives an overview of the basic principles, the instrumentation designs, and the performance of HD sample injection systems for microchip electrophoresis.     

Numerical analysis of an electrokinetic double-focusing injection technique for microchip CE

The injection techniques in electrophoresis microchips play an important role in the sample-handling process, whose characteristics determine the separation performance achieved, and the shape of a sample plug delivered into the separation channel has a great impact on the high-quality separation performance as well. This paper describes a numerical investigation of different electrokinetic injection techniques to deliver a sample plug within electrophoresis microchips. A novel double-focusing injection system is designed and fabricated, which involves four accessory arm channels in which symmetrical focusing potentials are loaded to form a unique parallel electric field distribution in the intersection of injection channel and separation channel. The parallel electric field effectuates virtual walls to confine the spreading of a sample plug at the intersection and prevents sample leakage into separation channel during the dispensing step. The key features of this technique over other injection techniques are the abilities to generate regular and nondistorted shape of sample plugs and deliver the variable-volume sample plugs by electrokinetic focusing. The detection peak in the proposed injection system is uniform regardless of the position of the detection probe in the separation channel, and the peak resolution is greatly enhanced. Finally, the double-focusing injection technique shows the flexibility in detection position and ensures improved signal sensitivity with good peak resolution due to the delivered high-quality sample plug.     

Electrophoretic affinity measurements on microchip. Determination of binding affinities between diketopiperazine receptors and peptide ligands

ACE on a microchip (MC-ACE) is introduced as a fast and reliable method to determine binding affinities. It is based on monitoring the change in the ionic mobility of a receptor upon binding to a ligand, or vice versa. The method is complementary to other standard methods for binding affinity determinations, like isothermal titration calorimetry (ITC), NMR, UV-Vis spectroscopy, etc. and allows for affinity studies of weak to strong binding interactions. The method is attractive since it principally allows for the analysis of the binding affinity of multiple receptors to a given ligand and requires comparatively small quantities of the binding partners (particularly in comparison to affinity measurements on capillary). We demonstrate the applicability of MC-ACE for the determination of the binding affinities between acid-rich diketopiperazine receptors and basic tripeptides in aqueous solution.     

Frontal analysis on a microchip

Conventional microchip applications involving capillary electrophoresis (CE) typically inject a sample along one channel and use an intersection of two channels to define the sample plug--the portion of sample to be analysed along a second channel. In contrast to this method of zone separation, frontal analysis proceeds by injecting sample continuously into a single channel or column. Frontal analysis is more common in macroscopic procedures but there are benefits in sensitivity and device density to its application to electrophoresis on microchips. This work compares conventional microchip zone analysis with frontal analysis in the separation of PCR products. Although we detect on the order of 5000 fluorophores with a compact instrument using the zone separation CE method, we found a several-fold increase in the effective signal-to-noise ratio by using a frontal analysis method. By removing the need for additional channels and reservoirs the frontal method would allow device densities to be significantly increased, potentially improving the cost-effectiveness of microchip analyses in applications such as medical diagnostics.