Curing of linear and crosslinked epoxy systems: A fluorescence study with dansyl derivatives

The curing of diglycidyl ether of bisphenol A (DGEBA) with N,N′-dimethylethylenediamine (N,N′-DMEDA) or ethylenediamine (EDA) was monitored by fluorescence spectroscopy and Fourier transform infrared (in the near-infrared region). 5-Dimethylamino-naphthalene-1-sulfonamide (DNS) derivatives were used as probes (fluorophores added to the reaction mixture) and labels (fluorophores attached by covalent bonds to diglycidyl reactants). The term containing the ratio of the reaction rate constants for the addition of the secondary and primary amine hydrogens to the epoxide was included in the reduced reaction rate term for the autocatalyzed and catalyzed epoxide curing reactions. The changes in the integrated fluorescence intensities of the labels during the epoxy group conversion indicated, in some cases, the most important changes in the chemical transformations of the reaction mixture: the epoxy group conversion, during which a rapid increase in the tertiary amino group concentration was first observed; the gel point (for EDA); and the entry of the system into the glassy state (for N,N′-DMEDA and EDA). The fluorescence probes monitored neither the gel point nor the threshold of the glassy state. For the DGEBA–N,N′-DMEDA system, a wavy dependence of the integrated fluorescence intensities of the DNS labels on the epoxy group conversion might reflect the molar concentrations of polymer homologues (referred to the initial number of moles in the system) in the reaction mixtures of the diepoxide and secondary diamine. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 64–78, 2004     

Mechanistic modeling of the reaction kinetics of phenyl glycidyl ether (PGE) + aniline using heat flow and heat capacity profiles from modulated temperature DSC

Modulated temperature DSC (MTDSC) has been performed on phenyl glycidyl ether (PGE) + aniline in order to obtain the non-reversing heat flow and heat capacity profiles simultaneously in a wide range of cure temperatures and mixture compositions. The epoxy (PGE) conversion as determined from the former signal corresponds to the one obtained from separate high performance liquid chromatography (HPLC), while the latter signal contains information on the individual reaction steps. Optimized kinetic parameters using a mechanistic approach, including both reactive and non-reactive complexes can successfully simulate MTDSC measurements for isothermal reaction temperatures ranging from 50 to 120 °C and for non-isothermal experiments with mixture compositions corresponding to concentrations of aniline in a range from 1.68 to 6.53 mol kg⁻¹. Concentration profiles for three mixture compositions as obtained from HPLC are also well predicted. The activation energies for the primary amine and secondary amine-epoxy reaction catalyzed by hydroxyl groups are 50 and 52 kJ mol⁻¹, respectively, while the initiation of the reaction corresponds to the primary amine-epoxy reaction catalyzed by primary amine groups with an activation energy of 72 kJ mol⁻¹. A negative substitution effect can be calculated at 0.18 from the ratio of secondary amine to primary amine-epoxy reaction rate constants.     

Structure of a typical amine-cured epoxy resin

A technique for estimating M_c, the molecular weight between crosslinks, of amine-cured epoxy resins is described. The technique is based upon the stoichiometry of the curing reaction and the amount of primary amino and epoxy groups remaining in the polymer at a given time. The M_c values so calculated are shown to be consistent with M_c results obtained from separate measurements of swelling and the polymer–solvent interaction parameter χ₁ for the range of polymer concentration in which both measurements could be obtained. A means of estimating the relative reaction rates of the primary and secondary amino groups with the epoxy groups is given. Under proper curing conditions the amine–epoxy reaction goes very nearly to completion. The presence or absence of an exotherm has no noticeable effect on the course of the reaction between bisphenol A-epichlorohydrin (Epon 828) and methylene dianiline.     

Reaction thermodynamics of amine‐cured epoxy systems: Validation of the enthalpy and heat capacity of reaction as determined by modulated temperature differential scanning calorimetry

The reaction enthalpy and reaction heat capacity of three aromatic epoxy–amine systems have been determined with modulated temperature diffential scanning calorimetry (MTDSC), mostly in quasi‐isothermal conditions, over a wide temperature range (33–140 °C) and for different mixture compositions. The reaction enthalpy is only slightly dependent on the epoxy–amine chemistry, from ?111 to ?98 kJ/mol epoxy functionality. With the model system phenyl glycidyl ether (PGE)+aniline, the reaction enthalpy of the secondary amine–epoxy reaction step is equal to that of the primary amine–epoxy reaction. Group contributions needed to calculate the reaction heat capacity with an additivity approach are evaluated, and a new value of 37.2 J mol^?1 K^?1 for the group N? (H)(C)(CB) is proposed. With this group contribution, the additivity method predicts almost equal values for the reaction heat capacity of both amine–epoxy reaction steps at 298.15 K (Δ_rC_p,prim = 15.7 J mol^?1 K^?1 and Δ_rC_p,sec = 14.6 J mol^?1 K^?1), whereas the experimental value of Δ_rC_p,sec is about three times larger than that of Δ_rC_p,prim at 100 °C. These results are confirmed experimentally for PGE+aniline as a different temperature dependence of both reaction heat capacities. MTDSC therefore is potentially interesting for differentiating between reactive species in an epoxy–amine reaction, a benefit previously assigned to spectroscopic methods only. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 594–608, 2003     

双(2,3-环氧环戊基)醚与双酚A环氧树脂混合体系固化机理的研究

用红外光谱法、电导法和化学分析对双(2,3-环氧环戊基)醚(W-95)与4,4′-二氨基二苯甲烷(MDA)的反应速度进行了测定,并和双酚A环氧树脂(E-54)与MDA的反应进行了比较。两个反应体系的表现反应活化能的测定结果接近相等。若W-95的环氧基与MDA的Ⅰ级胺和Ⅱ级胺的反应速度为k_1′和k_′,而E-54的为k_1和k_2,则它们的相对反应速度为:k_1:k_2:k_1′:k_2′=200:22:20:1。本文对W-95和E-54混合体系的固化机理也作了探讨。     

Determination of constants of the reaction of epoxy model compounds with organic amines in actual conditions

Kinetic studies of the interaction of monoepoxides with primary and secondary monoamines are carried out. It is shown that the reactivity of the epoxide ring of an active modifier depends on the structure during interaction both in bulk and in solvent environment. It was found that the ratio of the constants of the reaction of primary amino groups with an epoxy ring to the constants of the secondary amine is about 2.     

Novel,environmentally friendly crosslinking system of an epoxy using an amino acid: Tryptophan‐cured diglycidyl ether of bisphenol A epoxy

Tryptophan, an amino acid, has been used as a novel, environmentally friendly curing agent instead of toxic curing agents to crosslink the diglycidyl ether of bisphenol A (DGEBA) epoxy resin. The curing reaction of tryptophan/DGEBA mixtures of different ratios and the effect of the imidazole catalyst on the reaction have been evaluated. The optimum reaction ratio of DGEBA to tryptophan has been determined to be 3:1 with 1 wt % catalyst, and the curing mechanism of the novel reaction system has been studied and elucidated. In situ Fourier transform infrared spectra indicate that with the extraction of a hydrogen from NH₃⁺ in zwitterions from tryptophan, the formed nucleophilic primary amine and carboxylate anions of the tryptophan can readily participate in the ring‐opening reaction with epoxy. The secondary amine, formed from the primary amine, can further participate in the ring‐opening reaction with epoxy and form the crosslinked network. The crosslinked structure exhibits a reasonably high glass‐transition temperature and thermal stability. A catalyst‐initiated chain reaction mechanism is proposed for the curing reaction of the epoxy with zwitterion amino acid hardeners. The replacement of toxic curing agents with this novel, environmentally friendly curing agent is an important step toward a next‐generation green electronics industry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 181–190, 2007     

Curing of epoxide resins: Model reactions of curing with amines

The reaction of tetrafunctional diamines and bifunctional amines with monoepoxy compounds was investigated by gel-permeation chromatography. At a stoichiometrically equivalent ratio of the functional groups or excess of amine, the consecutive reaction of the epoxide groups with the hydrogen atoms of the amino groups is the only reaction that is taking place; if epoxide is present in excess, the OH groups formed in the reaction are gradually added to the epoxide groups. The ratio of the rate constants of the reaction of the epoxy group with the hydrogen atoms of the primary and secondary amino group was calculated from the concentrations of the reaction products at various excess amounts of amines. The ratio is in good accord with the value calculated from the gel points and limiting stoichiometric ratios in the curing of diepoxides with diamines.     

Facile synthesis of 1,8-naphthalimides in palladium-catalysed aminocarbonylation of 1,8-diiodo-naphthalene

1,8-Diiodo-naphthalene was aminocarbonylated with various primary and secondary amines in the presence of palladium(0) complexes formed in situ from palladium(II) acetate and triphenylphosphine. In the case of primary amines, depending on the amine to substrate ratio, two types of products have been obtained in highly chemoselective reaction: dicarboxamides and N-substituted imides have been formed at high and low amine to substrate ratio, respectively. The reaction tolerates the ester functionality, so that amino acid esters could serve as N-nucleophiles and in this way, naphthalimides possessing stereogenic centre in the N-substituent could be synthesised.     

Morphologic and kinetic study of an epoxy-poly(ethyleneoxide) system. The fluorescence to predict miscibility

The kinetic of the curing process in the ethylenediamine (EDA)-poly (bisphenol A-co-epichlorohydrin) glycidyl end-capped (DGEBA) mixture modified with poly(ethylene oxide) (PEO) was studied. The epoxy component was labeled with a fluorescence group (dansyl) treating the DGEBA with the reactive dansyl derivative DNS-EDA. Dynamic DSC experiments were carried out and from their results the effect of the PEO composition on the epoxy curing was discussed. Furthermore, the effect of cure temperature and PEO composition on the morphology and crystallinity of the blend were studied as well. The morphologic study was carried out using complementarily optical transmission (TOM) and epifluorescence (EFM) microscopy. It was observed that: i) the addition of a non-reactive thermoplastic leads to a dilution effect of the reactive groups and therefore a decrease of the epoxy amine reaction rate; ii) the PEO composition does not seem to affect the non catalyzed process of the epoxy curing, while an increase in the PEO fraction within the epoxy/PEO mixture seems to change the mechanism of the cure reaction; iii) dynamic DSC scans, TOM and EFM images and steady state fluorescence spectra of the cured samples suggest that when the curing temperature increases there is an increase in the miscibility between PEO and the epoxy-amine reaction mixture; and iv) a reduction in the PEO/cured epoxy miscibility as the fraction of PEO increases was observed.     

Theoretical study of gas phase reactions of important SOA intermediates: (cis‐ and trans‐) BEPOX and β‐IEPOX with OH radical

Mechanisms for hydroxide radicals reacting with 2,3‐epoxy‐1,4‐butanediol (BEPOX) and 2‐methyl‐2,3‐epoxy‐1,4‐butanediol (β‐IEPOX) in the gas phase are investigated using quantum chemistry computations. Geometries of all the structures are optimized at the X3LYP/6‐31+g(d,p) level. The ground‐state energy for each structure is then refined at the CCSD(T)/6‐31+g(d,p) level. All possible reaction paths for BEPOX and β‐IEPOX are analyzed. The results show that during BEPOX and β‐IEPOX gas phase reactions, hydrogen abstractions on C_chain? H are the most energetically favorable reaction paths (S3, S7) while the addition reactions (S6, S9) are not likely to occur. The present theoretical study is consistent with previous experimental results. © 2013 Wiley Periodicals, Inc.     

Reductive monoalkylation of nitro aryls in one-pot

The scope of the serendipitous reductive monoalkylation of ethyl (4-methoxy-3-nitrophenyl) acetate taking place during reduction of the nitro functionality to the corresponding primary amine when treated with hydrogen (1 atm) over Pd/C (10%) in ethanol is investigated. Upon prolonged reaction time the reaction conducted in ethanol and methanol yields significant amount of the corresponding secondary amines, while when performed in n-butanol and i-propanol it only resulted in the formation of a small amount of the corresponding secondary amines. Further development of the reductive monoalkylation reaction provided conditions that facilitate conversion of a range of different nitro aryls in one-pot to the corresponding secondary benzyl amino aryls in mostly good to excellent yields. This is accomplished by using hydrogen (1 atm) over Pd/C (10%) as reducing agent and benzaldehyde as the benzyl source combined with a stepwise reaction sequence. This chemistry was further extended to the formation of substituted benzyl amino aryls. The yields of the latter products varied dramatically depending on the substitution patterns associated with the benzaldehyde. However, by altering the reaction conditions it was possible to improve the yields of the benzylated products.     

Influence of substituents on the kinetics of epoxy/aromatic diamine resin systems

Eleven different epoxy/diamine systems, including tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), triglycidyl p‐aminophenol (TGAP), and diglycidyl ether of bisphenol A (DGEBA) with 4,4′‐diaminodiphenylsulfone (DDS), diethyltoluenediamine (DETDA), dimethylthiotoluenediamine (DMTDA), and meta‐phenylenediamine (m‐PDA), were studied with near‐infrared spectroscopy at different temperatures. The reactivities of the epoxies were determined and found to be in the following order when reacted with the same amine: DGEBA > TGAP > TGDDM. When the primary amine was reacted with the same epoxy, the order was DETDA > DDS > DMTDA; for the secondary amine, the order was DETDA > DMTDA > DDS. The relative reaction rates of the secondary amine to the primary amine were compared and discussed in terms of the structural differences and the corresponding substitution effect. It was concluded that the increase in the secondary amine reactivity of DETDA and DMTDA was caused by the deconjugation of the benzene‐ring π electrons from the lone pair on the N atom. The overall order of the secondary amine relative reactivity was DMTDA > DETDA > DDS for the same epoxy and TGDDM > TGAP > DGEBA for the same amine. The m‐PDA systems had no significant positive or negative substitution effects. Molecular orbital calculations were performed, and the results showed the most significant deconjugation effect in the secondary amine of DETDA. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3143–3156, 2004     

Spectrofluorimetric flow-injection determination of tertiary amines in non-aqueous media

The cyclic condensation of malonic acid with acetic anhydride in non-aqueous media is catalyzed selectively by tertiary amines. This derivatization reaction is adapted for flow injection analysis. A reaction pathway for the cyclization of a mixed anhydride condensate to form a fluorescent fully acylated phloroglucinol carboxylic acid is proposed. The effects of reaction parameters on the sensitivity of the reactionare described and calibration data are presented for ?2.7 mM triethylamine, tripentylamine, N,N-diethylaniline and pyridine. A secondary amine (diethylamine) gave a negligible response, but both primary and secondary amines partially quenched the fluorescence induced by a tertiary amine.     

Isoconversional kinetic analysis of stoichiometric and off-stoichiometric epoxy-amine cures

The curing reaction of stoichiometric and off-stoichiometric diglycidyl ether of bisphenol A (DGEBA) and 1,3-phenylene diamine (m-PDA) mixtures was studied by differential scanning calorimetry, thermogravimetric analysis and rheological measurements. In order to highlight the side reactions such as etherification and homopolymerization, the neat DGEBA and DGEBA/DMBA (N,N-dimethylbenzylamine) mixture were examined. The classical model-fitting and the advanced isoconversional methods were used to determine the activation energy of the different reactions. The advanced isoconversional method leads to a good agreement between isothermal, nonisothermal and rheological results. The effective activation energies of primary amine epoxy reaction, etherification and homopolymerization were estimated to about 55-60, 104 and 170 kJ mol⁻¹, respectively.     

Electrochemical synthesis of new organic compounds based on the oxidation of 1,4-dihydroxybenzene derivatives in the presence of primary and secondary amines

An efficient method for the synthesis of 2-benzyl(4-hydroxyphenyl)amino)-6-(benzylamino)-p-benzoquinone derivatives and 2,5-bis-benzyl(methyl)amino)-p-benzoquinone based on the Michael type reaction is described. The electrochemically generated p-benzoquinone reacted with benzylamine derivatives (primary amines) and N-methylbenzylamine (a secondary amine), respectively, to produce the final products. In this work, some new symmetric and asymmetric p-benzoquinone derivatives are synthesized using green solvents with high yields.     

‘Reductive ozonolysis’ via a new fragmentation of carbonyl oxides

This account describes the development of methodologies for ‘reductive’ ozonolysis, the direct ozonolytic conversion of alkenes into carbonyl groups without the intermediacy of 1,2,4-trioxolanes (ozonides). Ozonolysis of alkenes in the presence of DMSO produces a mixture of aldehyde and ozonide. The combination of DMSO and Et₃N results in improved yields of carbonyls but still leaves unacceptable levels of residual ozonides; similar results are obtained using secondary or tertiary amines in the absence of DMSO. The influence of amines is believed to result from conversion to the corresponding N-oxides; ozonolysis in the presence of amine N-oxides efficiently suppresses ozonide formation, generating high yields of aldehydes. The reactions with amine oxides are hypothesized to involve an unprecedented trapping of carbonyl oxides to generate a zwitterionic adduct, which fragments to produce the desired carbonyl group, an amine, and ¹O₂.     

Acceleration of amine/epoxy reactions with N‐methyl secondary amines

Kinetic studies established that the monomethylation of a primary amine leads to significantly higher reaction rates with glycidyl ethers. The relative rates for approximately 25 amines were determined in an alcohol solvent under pseudo‐first‐order conditions (excess epoxy). The rates were referenced to aniline. For the aliphatic amines, reactivity consistently increased upon going from a primary amine to the corresponding N‐methyl secondary amine. This acceleration effect was not seen for aniline. The enhanced reactivity was also seen in curing systems, both with pure methylated amine curing agents and with complex mixtures obtained from the partial methylation of polyamines. Economically viable partially methylated amine curing agents were obtained by the reductive alkylation of commercial polyamines with formaldehyde and by the reaction of monomethylamine with 3‐(N‐methylamino)propionitrile in the presence of hydrogen and a hydrogenation catalyst. Although actual cure performance is based on a complex combination of several factors, the acceleration due to monomethylation could be a useful tool for enhancing amine/epoxy curing reactions. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 921–930, 2000     

超声波技术制备功能化二氧化硅在苯酚和碳酸二甲酯甲基化反应中的应用

Porous silica modified with -（CH2）3NH2 （primary amine）, -（CH2）3NHCH2CH2NH2 （secondary/primary amine） and -（CH2）3N-cycl-（CH2）4 （tertiary amine） were synthesized by ultrasonic technique under mild conditions. The samples were characterized by BET, elemental analysis and TG, showing that the organosilane moieties were grafted onto the surface of porous silica by covalent bond. The structure of the organosilane moieties and ultrasonic treatment time were all significant for the quantities of grafted amino groups. The samples exhibited promising catalytic properties towards the methylation reaction of phenol with dimethyl carbonate （DMC）. The methylation reaction with the modified samples featured high selectivity at high conversion. The samples were subjected to utilization for a few recycles without obvious loss of activity to indicate that ultrasonic technique was effective for the preparation of organically modified porous silica catalysts.