A Method for Increasing the Sensitivity of Phase Doppler Interferometry to seed particles in liquid spray flows

A method has been developed to increase the sensitivity of phase Doppler interferometry-based particle sizing systems to small particles in the presence of a spray containing large and small droplets; an important consideration when using seed particles to track the gas-phase velocity in multi-phase flows. The method, applicable to PDPA systems configured to operate in first and higher order refraction mode, involves doping the sprayed liquid with a dye that is strongly absorbing at the incident laser wavelengths. This results in greatly diminished scattered intensity from larger droplets, thus allowing the photomultiplier gain to be set to a level sufficient to easily detect small particles without saturation. Tests conducted indicate that, at a collection angle of 30° and droplet absorptivity of γ = 0.014/μm, the PDPA can accurately size absorbing droplets up to approximately 200 μm. This upper limit can be extended by changing selection angle. Tests performed with an actual spray demonstrated that the method allowed detection of 1 μm to 235 μm droplets; more than four times the instrument's usual range of 50: 1. A data correction scheme to determine the effective probe volume radius for each particle size class has been developed for absorbing particles, as standard correction schemes derived for non-absorbing droplets excessively weigh distributions toward smaller particles.     

相态对冰水混合云微观特性反演的影响研究

当云层的温度在－40℃~0℃之间时, 云层中会存在冰和水两种相态的云滴, 其散射特性与纯水云以及纯冰云特性有较大差异, 因此遥感反演混合相云层的微观和宏观物理特性具有重要的意义。本文采用冰水双层球模型模拟了冰水混合云中的云滴, 利用Mie理论计算了纯水、纯冰和冰水颗粒的单次散射特性, 分析了单次散射相函数, 不对称因子, 单次散射反照率等随着有效半径、相态、内外半径比等的变化特性。利用离散纵标法(DISORT)计算了水云和冰云对0.75 μm、2.16 μm和3.3 μm的双向反射函数, 讨论了利用纯水滴和纯冰滴反演冰水混合云滴的误差。分析结果表明, 利用0.75 μm和2.16 μm的太阳光反演冰水混合云的光学厚度和有效半径时, 光学厚度误差较大, 有效半径误差较小; 结合0.75 μm和3.3 μm的太阳光反演冰水混合云的光学厚度和有效半径时, 光学厚度误差较小, 有效半径误差较大, 其会高估其有效半径; 另外结合0.75 μm和3.3 μm这两个波长的反射函数反演冰水云的冰水混合比更为有效。     

Electrostatic Charge Measurement and Charge Neutralization of Fine Aerosol Particles during the Generation Process

An aerosol charge analyzer has been constructed to measure the charge distribution of NaCl particles generated in the laboratory. A radioactive electrostatic charge neutralizer utilizing Po‐210 was used to neutralize the electrostatic charge of the particles. The atomization technique was used to generate NaCl particles with diameters of 0.2 to 0.8 μm, while the evaporation and condensation method was adopted to generate particles of 0.01 to 0.2 μm in diameter. The experimental data demonstrates that the absolute average particle charge depends on the particle diameter, and is higher than that calculated by the Boltzmann charge equilibrium for particles within the range of 0.2 to 0.8 μm. The charge increases with decreasing NaCl concentration. When these particles are neutralized using the Po‐210 neutralizer, it is found that the electrostatic charge reaches the Boltzmann charge equilibrium. For 0.01 to 0.2 μm NaCl particles generated using the evaporation and condensation method, test results show that the absolute average particle charge is higher than that calculated by the Boltzmann charge equilibrium for particles larger than 0.03 to 0.05 μm in diameter, while it is lower than that predicted by the Fuchs theory [1], for particles smaller than 0.03 to 0.05 μm. However, after charge neutralization, particles with diameter above 0.05 μm reach the Boltzmann charge equilibrium condition, and the charges for particles with diameters of 0.010 to 0.05 μm, agree well with Fuchs' theory.     

Optimization of mark edge recording waveform for a phase change rewritable optical disk using a 680 nm laser diode

A high density mark edge recording method on a phase change rewritable disk is reported. A carrier-to-noise ratio of 55 dB for a mark length of 0.55,μm is obtained by using a 680 nm, NA 0.6 head and a phase change rewritable disk. In mark edge recording, it is necessary to record each mark in correct length. A new laser power modulation pattern is proposed. This pattern consists of a first-pulse, a multi-pulse chain and a last-pulse. Both positions of the first-ptilse and the last-pulse are movable. By adjusting these positions, a jitter, σ/T_w (T_w is window margin), is improved to 6.5% in high density EFM (Eight to Fourteen Modulation) recording of 0.4 μm/bit.     

Aerosol Generation Method for Measuring Particles Suspended in Water – Detection of Particulate Impurities in Ultrapure Water and Sizing of Fine Powders –

The method described is based on the fact that the measurement of particles in the gaseous phase is generally easier than that in the liquid phase for fine particles smaller than 1 μm in diameter. The system consists of a liquid nebulizing unit, evaporator, condenser, mixing diluter and two different aerosol sizing instruments. It has been found that this method can continuously detect particulate impurities in ultrapure water in situ and can measure the size distribution of fine powders in the submicron particle size range down to about 0.05 μm.     

Parallel optical coherence tomography using a CCD camera

Parallel optical coherence tomography is demonstrated using a 12-bit scientific-grade charge-coupled device array.A superluminescent diode in combination with a free-space Michelson interferometer was employed to achieve 10-μm axial resolution and 1.1-μm transverse resolution on a 902×575 μm2 field of view.We imaged a test mirror and bovine retinal tissue using a four-step phase shift method.     

Acoustic particle manipulation in a 40 kHz quarter-wavelength standing wave with an air boundary

An implementation of a quarter-wavelength standing wave separator that exploits an air drum to achieve the pressure node is presented and characterized experimentally. The air drum configuration was implemented and tested in a set-up with a 40 kHz transducer immersed in a water tank with the quarter-wavelength gap being approximately 9 mm wide. Injection of suspensions of 5 μm and 45 μm diameter polystyrene particles at flow rates of 30 ml/h and 60 ml/h was studied and particle deflection towards the pressure node at the air drum surface was observed for a range of acoustic pressures. Computational results on single particle trajectories show good agreement with the experimental findings for the 45 μm particles, but not for the 5 μm particles. These were considered to behave as aggregates of higher effective dimension, due to their much higher number density relative to the 45 μm particles in the suspensions used. The set-up developed in this study includes a robust method for achieving a pressure node in a quarter-wavelength system and can represent the first step toward the development of an alternative separator configuration in respect to small channel MHz range operated systems for the manipulation of particles streams.     

The use of a temperature programmable brabender mixing head for the evaluation of the processing characteristics of poly(vinyl chloride)

A technique is described for determining the temperature-torque profile of a PVC compound in a Brabender Plasticorder mixing chamber from room temperature to the temperature at which degradation occurs. Within this temperature range many PVC compounds show three characteristic peaks in the torque temperature trace. It is suggested that these three peaks are associated with the breakdown of the PVC powder particles (Stage III, 100 to 150 μm), micro-granules (Stage II, 0.5 to 2 μm), and primary particles (Stage I, 10 nm), respectively. The positions and shapes of these peaks are functions of the compound being investigated and as such can be used to characterize the processing behavior of the compound.

The greater part of the work has been carried out using suspension polymers but application of the technique to mass and emulsion polymers suggests that the conclusions are applicable to all polymers which possess a particulate substructure.     

SCF micronization of poly-3-hydroxybutyrate using supercritical antisolvent

Micronization of poly-3-hydroxybutyrate (PHB) by the supercritical fluid antisolvent precipitation (SAS) technique using supercritical carbon dioxide as an antisolvent was studied experimentally. The possibility of preparing particles of varying morphology (including hollow spheres) and specified size from 100 nm to 20 μm was demonstrated. The influence of different mechanisms of solid phase formation during SAS micronization on the size and morphology of PHB microparticles under different experimental conditions was considered.     

Measuring in-plane and out-of-plane coupled motions of microstructures by stroboscopic microscopic interferometry

A stroboscopic Mirau microscopic interferometer system for measuring in-plane and out-of-plane periodic motions of microstructures is demonstrated. One full cycle of a periodic motion is divided into a number of motion phases. One sequence of interferograms with different phase shifting steps is collected at every motion phase by using stroboscopic imaging. A bright-field image can be extracted from one sequence of interferograms with the same motion phase. In-plane displacements are measured by applying an image matching method to all bright-field images, followed by a compensation for the relative positions of interferograms at the different motion phases, before calculating the phase distribution related to out-of-plane deformation. We demonstrate its capability for measuring a combination of out-of-plane deformation and in-plane displacement in a microresonator.     

喷射成形粉末高温合金FGH4095M的制备及组织特征

喷射成形是一种近净成形的在粉末冶金气体雾化制粉技术基础上发展起来的快速凝固技术. 本文采用喷射成形技术制备成分优化后的FGH4095M合金, 研究了喷射成形FGH4095M合金沉积坯的致密度、显微组织特征, 特别是研究了喷射成形高温合金组织中特殊形貌的γ’相. 研究表明, 致密度与沉积坯部位有关, 底部致密度最高, 可达99.63%, 热等静压后的致密度可达100%. 喷射成形合金组织以均匀细小的等轴晶为主, 不存在原始颗粒边界; 一次γ’ 相尺寸约为0.6-0.8 μm, 二次γ’相尺寸约为0.1-0.5 μm, 在二次γ’相的间隙中有少量尺寸约为10-20 nm的三次γ’相. 喷射成形FGH4095M 合金中的二次 γ’相中出现特殊形貌的γ’相, 这是由单个γ’颗粒分裂形成, 与沉积过程的低冷却速度有关. 分裂过程是γ’颗粒总能量降低的过程, γ’颗粒间的弹性交互作用能起到主导作用. 对分裂γ’相的等效直径进行统计, 得到γ’ 相等效直径超过0.40 μm 后, 会出现分裂趋势. 合金具备优异的拉伸性能, 室温塑性得到显著提高, 出现γ’ 相分裂的特殊形貌组织是否对合金性能的提高产生直接影响仍需进行进一步的研究.     

冲击波作用下微米尺度金属颗粒群的动力学行为

基于平面化爆驱动飞片高压加载技术和激光测速技术,研究了冲击波加载不同粒径锡颗粒群的微喷射行为以及在空气中的减速规律.实验结果表明,锡颗粒的最快喷射速度随粒径增大而显著增大.通过对微喷射形成过程的三维光滑粒子流体动力学方法数值模拟发现,大粒径锡颗粒之间存在较大的空隙结构,冲击波与空隙结构的相互作用诱导产生高速汇聚射流,空隙结构越大对应的喷射速度也越高.此外,通过研究不同粒径颗粒在复杂流场中的减速规律,进一步深化了对微喷射破碎后的颗粒尺度状态以及混合输运特性的认识.研究结果对于预测和分析冲击波加载微米颗粒群的微喷混合特性具有一定价值.     

高掺镁LiNbO3晶体折射率温度系数的表示式

推导了掺５ｍｏｌ％ＭｇＯ的ＬｉＮｂＯ３晶体折射率温度系数的表示式。利用这些表示式可以计算２９３～４２８Ｋ温度和０．５３９８μｍ～１．３４１４μｍ波长范围内的折射率温度系度，结果表明：计算值和实验值的最大相对偏差是１２％，用具有最大相对偏差的折射率温度系数的计算值，计算１．０７９５μｍ波长的非临界相位匹配温度，其值为３８２．４Ｋ，它与实验值仅差６Ｋ。因此，本文得到的表示式，对于采用这种晶体，设计在上     

The Phase-Doppler-Difference-Method,a New-Laser-Doppler Technique for Simultaneous Size and Velocity Measurements. Part 2: Optical particle characteristics as a base for the new diagnostic technique

Simultaneous size and velocity measurements can be obtained by using photodetector positions of different off-axis-angles. But not for all of these positions one receives unambiguous results for the correlation between the phase difference and the particle diameter. This can be clearly demonstrated by the plots of the numerical calculations of the complete Mie's scattering equations. These plots show that for transparent particles which exceed the continuous phase in density at special off-axis-angles the situation of light refraction changes into a situation of additional light reflection or vice versa. On the other hand for transparent particles which are less dense compared with the continuous phase and for totally absorbing materials these plots confirm the simplified equations for reckoning the particle diameter by the laws of geometrical optics. The good agreement between these results can also be verified for the backscatter mode for measurements of metallic spheres with an imaginary refractive index.     

Non-collinear phase matched 4-wave mixing of CO2 and NH3 laser radiation in germanium

4-wave mixing has been demonstrated in room temperature germanium using a TEA CO₂ laser (9.3 μm) and an optically pumped NH₃ laser (12.8 μm) as radiation sources. Non-collinear phase matched emission near 7 μm has been observed with a mixing efficiency close to the calculated value. The extension of this mixing process to generate wavelengths in the important region near 16 μm is discussed.     

Movable aperture lensless transmission microscopy: a novel phase retrieval algorithm

We propose an iterative phase retrieval method that uses a series of diffraction patterns, measured only in intensity, to solve for both amplitude and phase of the image wave function over a wide field of view and at wavelength-limited resolution. The new technique requires an aperture that is scanned to two or more positions over the object wave function. A simple implementation of the method is modeled and demonstrated, showing how the algorithm uses overlapping data in real space to resolve ambiguities in the solution. The technique opens up the possibility of practical transmission lensless microscopy at subatomic resolution using electrons, x rays, or nuclear particles.     

A nano-metallic-particles-based CMOS image sensor for DNA detection

In this paper we report on a study of the CMOS image sensor detection of DNA based on self-assembled nano-metallic particles, which are selectively deposited on the surface of the passive image sensor. The nano-metallic particles effectively block the optical radiation in the visible spectrum of ordinary light source. When such a technical method is applied to DNA detection, the requirement for a special UV light source in the most popular fluorescence is eliminated. The DNA detection methodology is tested on a CMOS sensor chip fabricated using a standard 0.5 μm CMOS process. It is demonstrated that the approach is highly selective to detecting even a signal-base mismatched DNA target with an extremely-low-concentration DNA sample down to 10 pM under an ordinary light source.     

A method for investigating the orientational behaviour of fibrous particles in gaseous flow

A method is described by which the angular orientation distribution of fibrous particles carried in a gaseous stream may be investigated. The method is based upon the interpretation of the spatial intensity distribution or scattering profile of laser light scattered by individual fibres. The scattering instrument used to capture the profiles is described, and the mathematical computation required to ascertain the orientation of each particle at the measurement point is detailed. Illustrative results are given for a study of airborne micromachined silicon particles of 12 μm length and 1.0 μm by 1.5 μm cross-section. The method is currently being employed by the authors to investigate ways of improving the orientation control over nonspherical particles in systems such as aerodynamic particle sizers and particle shape classifiers, since lack of particle orientation control is known to adversely affect the measurement accuracy of both these types of instrument.     

Direct near-field phase measurement of laser diodes employing a single-mode fiber interferometer

A method of direct measurement of near-field phase and intensity distribution of laser diodes employing a single-mode fiber interferometer is proposed and demonstrated. The phase and intensity of the output beam of the laser in the vicinity of the output facet are measured directly via interferometry. Using a 980 nm laser diode as an example, we obtained a beam width of 0.9 and 3.6 μm at the output facet in the vertical and horizontal axes, respectively. In addition, the phase information of the output beam was also obtained by using interferometry. This technique is particularly useful for laser diodes whose near-field phases are difficult to measure directly. The measured vertical and horizontal wavefront radius of curvatures of a laser diode are in good agreement with the calculation from Gaussian beam theory. Detailed understanding and measurement of the near-field phase and intensity distributions of light sources and optical components are essential for micro-optic designs with better mode matching to minimize the insertion loss.     

A Multi‐Thresholding Algorithm for Sizing out of Focus Particles

A methodology is presented that enables efficient acquisition of sufficient droplet information (e.g. diameter and aspect ratio) from images of in and out of focus droplets. The newly developed multi‐threshold algorithm is successfully implemented in the automatic particle/droplet image analysis (PDIA) system. Under the same optical hardware set‐up, and compared to the dual threshold methods [1], the multi‐threshold method increases the measurable/acceptable depth of field (DoF) of particles, especially for the small particles of diameters less than 50 μm (1098 pixels in this optical set‐up). When testing the 70 μm~110 μm and 100 μm~200 μm moving glass spheres, the dual threshold method can only detect 11%~29 % of the particles found by the multi‐threshold method. The multi‐threshold method is also capable of generating the aspect ratios of particles more accurately than dual threshold methods.