Demonstration of a multiwave coherent holographic beam combiner in a polymeric substrate

We demonstrate an efficient coherent holographic beam combiner (CHBC) that uses angle multiplexing of gratings in a thick polymeric substrate. Our experimental results compare well with the theoretical model based on the coupled-wave theory of multiwave mixing in a passive medium. A CHBC of this type may prove useful in producing a high-power laser by combining amplified beams produced by splitting a master oscillator. Furthermore, the ability to angle multiplex a large number of beams enables a CHBC to be used in multiple-beam interferometry applications as a high-precision surface sensor.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

Demonstration of a simple entangling optical gate and its use in bell-state analysis

We demonstrate a new architecture for an optical entangling gate that is significantly simpler than previous realizations, using partially polarizing beam splitters so that only a single optical mode-matching condition is required. We demonstrate operation of a controlled-z gate in both continuous-wave and pulsed regimes of operation, fully characterizing it in each case using quantum process tomography. We also demonstrate a fully resolving, nondeterministic optical Bell-state analyzer based on this controlled-z gate. This new architecture is ideally suited to guided optics implementations of optical gates.     

Reducing the stray light of holographic gratings by shifting the substrate a short distance in the direction parallel or perpendicular to the exposure interference fringes

This research proposes a simple and practical method to make low-stray-light gratings, where the substrate shifts about a 1 mm distance in the direction parallel or perpendicular to the exposure interference fringes. When the substrate shifts, a reference grating next to the substrate is used to adjust in real time the phase of the exposure interference fringes relative to the substrate. Shifting eliminates the exposure defects and therefore decreases the stray light of gratings. Several gratings are successfully made by using this method, which have straighter grooves,smoother surfaces, and lower stray light than gratings made in conventional interference lithography.     

全息技术制作二维光子晶体蓝宝石衬底提高发光二极管外量子效率

为了提高GaN基发光二极管(LED)的外量子效率,在蓝宝石衬底制作了二维光子晶体.衬底上的二维光子晶体结构采用激光全息技术和感应耦合等离子体(ICP)干法刻蚀技术制作,然后采用金属氧化物化学气相沉积(MOCVD)技术在图形蓝宝石衬底(PSS)上生长2μm厚的n型GaN层,4层量子阱和200nm厚的p型GaN层,形成LED结构.衬底上制作的二维光子晶体为六角晶格结构,晶格常数为3.8μm,刻蚀深度为800nm.LED器件光强输出测试结果显示,在PSS上制作的LED(PSS-LED)的发光强度普遍高于蓝宝石平 关键词： 全息 发光二极管 图形蓝宝石衬底 外量子效率     

Comment on “a simple model for the 1/f-type power spectrum” by M. Agu

A gaussian distribution of S, where 1/D₀S is a relaxation time, does not yield the 1/f spectrum.     

Three-dimensional object recognition by use of a photorefractive volume holographic processor

We present a photorefractive volume holographic processor for recognition of three-dimensional (3D) objects. The templates are recorded by use of a volume hologram in a photorefractive LiNbO(3):Fe crystal located at the Fresnel diffraction region and correlated in real time with a 3D object illuminated by coherent light. Experimental results for recognition of 3D objects are presented and discussed. To the best of our knowledge, this is the first time a photorefractive volume holographic technique for 3D object recognition has been reported.     

A simple technique for real time pulsewidth measurements of single ultrashort laser pulses

A simple technique is described employing noncollinear second harmonic generation, for real time measurement of the pulse duration of individual pulses in the 1 ps to 1 ns range. The pulsewidth is derived from the recorded two points of the second-order autocorrelation function. The system may be used as a permanent on-line monitor of the pulsewidth.     

通过保留相位进行全息图信息压缩的方法

从全息图的特点出发,研究了全息图的记录和再现原理,提出了一种对离轴菲涅耳全息图信息压缩的方法。对全息图进行傅里叶变换,滤除零级噪声及物光波的共轭波前,仅仅保留物光波的相位信息,而后以采用较低的采样频率对全息图重新抽样,从而大大减少了数字全息图的信息冗余。压缩后的全息图也可以获得良好像质的再现像。理论和实验均证明了该方法的可行性,为全息图的信息存贮与传输提供一条新的途径。     

A simple technique for the alignment of a ring resonator

A simple technique for the alignment of a ring resonator is presented. The positional and the directional alignments are obtained by the movements of independent mirrors. The effects of alignment inaccuracies on the performance of a ring resonator are discussed.     

Estimation of trap concentration in photorefractive crystals by a technique of adaptive holographic interferometry

12 GeO₂₀, Bi₁₂SiO₂₀, Bi₁₂TiO₂₀). Received: 17 June 1998/Revised version: 3 August 1998     

Improvement of holographic recording property of a Ce: KNSBN crystal by the moving grating technique

The moving grating technique is applied to improve the holographic recording property of the Ce: KNSBN crystal. In the case of extraordinarily polarized recording, the diffraction efficiency at large fringe modulations is enhanced by a factor of up to 35% at the optimum fringe velocity and the fringe modulation dynamic range is improved from m = 0.2 to m = 0.6. In the case of ordinarily polarized recording, a linear holographic reconstruction in the range of m ≤ 0.8 can be achieved by the moving grating at a fringe velocity of 9.6 nm/s. These results are significant in holography where a grey-level object needs to be recorded and reconstructed with high fidelity.     

Application of the holographic carrier fringe and FFT technique for deformation measurement

This paper describes a holographic system based on the use of fibre optics and automatic spatial carrier fringe pattern analysis. Carrier fringes are generated by simply translating the object beam between two exposures. Single-mode optical fibres are used to transfer both the object and reference beams. The fast Fourier transform method is used to process the interferograms: it extracts phase from fringe patterns resulting from the interference of tilted wavefronts. The method is illustrated by measuring the deformation of an arbitrarily clamped, uniformly loaded circular plate. The results are given for the perspective plot of the out-of-plane deformation field, the maps of wrapped and unwrapped phase, and a contour map of the unwrapped phase.     

Experimental setup for determining the carrier mobility using a transit time technique

A new scheme of the experimental setup for measuring the carrier mobility in thin films of organic semiconductor materials was proposed. Major factors controlling the time of exponential relaxation of the measuring system were analyzed. On this basis, conclusions were made on operating parameters of the measuring equipment required to reduce as much as possible the relaxation time. According to this, a new setup was developed. A qualitative improvement of current kinetic curves for a control sample was experimentally shown using the new setup. This allowed determination of transit times and carrier mobilities with high reliability.     

In situ technique for measuring the orthogonality of a plane wave to a substrate

A new compact in situ method of measuring the perpendicularity of a plane wave to a substrate is proposed. Off-axis cylindrical Fresnel lenses are used to focus a portion of the incident plane wave onto target lines. The displacement of the focal line from the targets is determined by the degree of angular misalignment. The proposed design has been incorporated into a 10-mm-thick fused-silica module, which enables us to obtain an alignment precision of better than 0.0083 degrees. This method is designed for use in optical assembly procedures that require an incident collimated beam that is normal to the alignment features. Experimental results are presented.     

Thickness measurement for submicron metallic coatings on a transparent substrate by laser optoacoustic technique

A new nondestructive technique for determining the thicknesses of submicron metallic coatings on transparent substrates is developed. The technique is based on measuring the frequency dependence of the efficiency of thermooptical conversion on the thickness of a metallic film in the case of its contact with a transparent fluid. Experiments were conducted with three chromium coatings of different thicknesses (0.2, 0.3, and 0.6 μm) on quartz substrates. Two different experimental schemes were used: a direct scheme (laser radiation hits the film from the side of the substrate) and an indirect one (the laser action upon the film occurs from the side of the fluid). The film thickness is determined by approximating the experimental frequency dependences of thermooptical conversion efficiency by theoretical curves with the use of the least-squares method. The optoacoustic method can be used for determination of coating thicknesses in the range from 50 nm to 5 μm with an error of about 50 nm.     

Remote detection of Raman scattering by use of a holographic optical element as a dispersive telescope

We describe the retrieval of nighttime lidar profiles by use of a large holographic optical element to simultaneously collect and spectrally disperse Raman-shifted return signals. Results obtained with a 20-Hz, 6-mJ/pulse , frequency-tripled Nd:YAG source demonstrate profiles for atmospheric nitrogen with a range greater than 1 km for a time average of 26 s.     

Switchable holographic gratings formed in polymer-dispersed liquid-crystal cells by use of a He-Ne laser

We report on the formation of switchable holographic transmission gratings in polymer-dispersed liquid-crystal cells by use of the 633-nm wavelength of a He-Ne laser. We present results for the structure, diffraction efficiency, and switching characteristics of the gratings.     

Improvement of the optical signal-to-noise ratio in common-path holographic storage by use of a polarization-controlling media structure

A holographic storage arrangement with common-path optics is likely to suffer from degradation of the optical signal-to-noise ratio (SNR) owing to scattering of the reference beam. Instead of the conventional method of spatial separation between the reference beam and a reconstruction beam, adoption of a combined spatial and polarization separation is proposed. To achieve polarization separation by using a photopolymer as the recording material, a media structure including retardation films and a reflection layer is proposed such that the polarization states of the two beams are the same inside the material but orthogonal outside. Preliminary experiments to show the feasibility of this idea for improving optical SNR are also demonstrated.     

Raman studies of InAs/In0.53Ga0.47As single quantum wells grown on InP substrate by M.B.E.

We analyzed using the Raman technique a series of single quantum wells of InAs/In _0.53Ga_0.47As at different thicknesses of InAs layer grown on a (100) InP substrate by MBE. These high lattice mismatch systems are particularly interesting for potential applications in the mid-IR wavelength range. The well thickness was between 6 and 12 monolayers. The In _0.53 Ga_0.47As grown on an InAs layer is subject to a tensile biaxial strain and the InAs to a compressive one. In the Raman spectra we observed an intense narrow line corresponding to the LO phonon of the InAs layer between a GaAs-like LO mode and a smaller InAs-like LO phonon typical of In_0.53Ga_0.47As. With the increase of the well thickness the experimental energy shift of the LO phonon of the InAs layer decreases, indicating a smaller strain, whereas the GaAs-like LO phonon of the alloy remains constant and the intensity ratio of these two modes becames smaller. The dominant and sharp features of the InAs LO and GaAs-like LO characterize the good quality of our structures. With the increase of the InAs layer thickness we also observed the appearance and the intensity rise of a weak peak around the frequency of the InAs TO mode. This peak could be associated with the TO mode that is forbidden in our scattering geometry. We believe that this is indicative of a slight deterioration of the structural perfection of the sample with the increase of the well thickness. To our knowledge, this is the first study of vibrational properties of InAs/In _0.53 Ga_0.47As single quantum wells grown on InP substrates.