Photodegradation of biodegradable polyesters: A comprehensive study on poly(l-lactide) and poly(?-caprolactone)

The photodegradation of melt-crystallized and amorphous-made poly(l-lactide) (PLLA-C and PLLA-A, respectively) and cast-crystallized poly(?-caprolactone) (PCL) was investigated comprehensively for the periods up to 200 h using gel permeation chromatography, differential scanning calorimetry, tensile testing, and polarization optical microscopy. The photodegradation of PLLA and PCL films proceeds via a bulk erosion mechanism, indicating that UV penetrates the specimens with no significant reduction in its intensity, irrespective of the chemical structure and the crystallinity of biodegradable polyesters. The photodegradability of PCL chains was higher than that of PLLA chains. This strongly suggests that the chemical structure of the two sequential groups adjacent to the ester oxygen rather than the density of ester group is crucial to determine the photodegradability of biodegradable polyesters. Although PLLA chains are photodegradable even in the crystalline regions, their photodegradability is lower than that in the amorphous regions. The significant increase in weight-average molecular weight (M_w)/number-average molecular weight (M_n) was observed for PLLA-A and PCL films, even when the decrease in M_n by UV irradiation was small. Most of the tensile properties of PLLA and PCL films remained unchanged during UV irradiation, while solely the elongation at break of PCL film significantly decreased. This result reflects that among the tensile properties the elongation at break was most sensitive to the change in molecular characteristics of biodegradable polyesters by UV irradiation. The contrast between bright and dark parts of Maltese crosses remained unchanged for the spherulites in PLLA-C and PCL films even after UV irradiation for 200 h. This result exhibits that the cleaved fraction of the tie chains was too low to cause the traceable disorientation of lamellae.     

聚甲基丙烯酸甲酯辐射裂解和消旋的空间立构效应

本文研究了三种不同空间立构聚甲基丙烯酸甲酯的辐射效应,提出裂解过程是一种裂解与重合的动态平衡过程。分子量降低和消旋作用对温度的依赖性,是由于分子运动和笼罩效应以及重合的空间位阻效应所致。辐照温度愈高,裂解产额愈大。相同条件下辐照,全同立构比无规立构试样的裂解产额更大。 全同立构聚甲基丙烯酸甲酯辐照后,不仅分子链断裂,而且空间立构也发生很大变化。随着辐照剂量的增加,全同立构含量逐渐减少,而无规立构含量和间同立构含量却逐渐增加。     

The effect of light on the viscosity and molecular mass of nitrocellulose

The photodegradation of a series of nitrocellulose (NC) samples with nitrogen contents ranging from 11.69% to 13.55% has been investigated by observing changes in molecular mass and viscosity using, respectively, size exclusion chromatography (SEC) and a modified cone and plate rheometer. When NC in γ-butyrolactone was subjected to UV light in the range 320-390 nm its specific viscosity (η_sp) was found to decrease noticeably, a change attributed to polymer chain scission and de-aggregation. This view was supported by an observed reduction in the mass average molecular mass (M_w). In contrast, irradiation with a single wavelength at 365 nm did not significantly change either η_sp or M_w and similar behaviour was observed when NC solutions were irradiated with visible light (400-500 nm). In the solid state, the photodegradation of water-wet NC is faster than that of the dried material, which is attributed to the catalytic effect of acids formed from the reaction between water and nitrogen oxides (NO_x) arising from NC decomposition. A higher degree of crystallinity in the NC, as found by X-ray diffraction (XRD), was shown to lead to a smaller decrease in viscosity and molecular mass. This is thought to be because the photodegradation reaction is suppressed in crystalline NC by more effective radical-radical recombination.     

Biobased myo-inositol as nucleator and stabilizer for poly(lactic acid)

myo-Inositol made from a biomass feedstock was used as an additive for poly (l-lactic acid) (PLLA) which was also made from biomass feedstock. The crystallization and stabilization of PLLA by the addition of myo-inositol were evaluated by the melt injection molding process. While the isothermal crystallization of PLLA at 100 °C had finished over 14 min after melting, that of PLLA with 5 wt% myo-inositol finished within 2 min. The crystal growth of PLLA started when the myo-Inositol crystal was added, and the crystallization was promoted. Furthermore, the molecular weight of PLLA with myo-inositol did not decrease during the melt-mixed at 200 °C, different from that of PLLA without the myo-inositol. myo-Inositol prevented the degradation of PLLA during the thermal melting process. The biomass carbon ratio measured by the accelerator mass spectroscopy method showed that the PLLA with 5 wt% myo-inositol was a fully biobased material. It was demonstrated that myo-inositol was a multi-functional biobased additive for the modification of PLLA without decreasing its mechanical properties.     

High-energy radiation forming chain scission and branching in polypropylene

The degradation of high molecular weight isotactic polypropylene (iPP) subjected to gamma rays irradiation up to 100 kGy in inert atmosphere was analyzed. The investigation relied upon complex viscosity, elastic modulus, gel fraction, morphology of the insoluble fraction and deconvoluted molecular weight distribution (MWD) curves. At low irradiation doses, already at 5 kGy, the MWD curve is strongly shifted to the low molecular weight side showing chain scission, which is confirmed using the calculated chain scission distribution function (CSDF). At high dose levels, the appearance of a shoulder in the high molecular weight side of the MWD curve indicates the formation of chain branching. The presence of a considerable insoluble fraction at these high dose levels indicates also the formation of cross-linking, which has different morphology then the insoluble fraction present in the original iPP. The rheological results show changes in the molecular structure of irradiated samples in agreement with the gel content data. The chromatographic and rheological data has shown that gamma irradiation of iPP produces chain scission, branching and cross-linking.     

Electron beam irradiation effects on poly(ethylene terephthalate)

Changes in poly(ethylene terephthalate) subjected to electron beam irradiation at doses up to 15 MGy and dose rate of 1.65 MGy/h, were investigated by differential scanning calorimetry, molecular weight measurement, X-ray photoelectron spectroscopy, and scanning electron microscopy. Irradiated samples showed a decrease of molecular weight with a minimum at 5 MGy, which is attributed to chain scission of the macromolecules and then an increase at further doses due to branching and some degradation effect. Irradiation in air is not an important factor because the high dose rate of irradiation inhibits oxygen diffusion in the samples.     

Poly(vinyl acetate) paints in works of art: A photochemical approach. Part 1

The photochemistry of poly(vinyl acetate), PVAc, homopolymer, of PVAc mixtures with selected pigments and fillers, and of accurate historic reproductions based on the colours prepared by Portuguese artist Joaquim Rodrigo and on those supplied by the company A Favrel was studied. The systems, applied as films, were irradiated at λ ≥ 300 nm and the changes followed by size exclusion chromatography, infrared spectroscopy, and colorimetry.PVAc as homopolymer or as an emulsion paint proved to be very stable to light, and after 5000 h of irradiation no gel fraction was observed. Φ_R (λ_irr = 313 nm) for chain scission for PVAc was determined to be 7 × 10⁻⁸. This value indicates that the mechanism/s operating when irradiating at λ ≥ 300 nm are different from those previously published with irradiation involving 254 nm. No side-group scission was observed, and main chain scission is the foremost photodegradation mechanism. Also, the metal ions present in the pigments do not affect the photochemical stability of the polymer.     

高分子量聚L-乳酸热降解回收L-丙交酯*

本文综述了高分子量聚L-乳酸(Poly(L-lactide), PLLA)经热降解直接回收L-丙交酯的研究进展。纯PLLA的热降解为无规反应,经添加金属类催化剂后,PLLA则可获得以L-丙交酯为主的热降解产物。本文介绍了聚乳酸热降解的反应机理,详细阐述了添加的金属催化剂的种类,及其催化PLLA热降解生成L-丙交酯及发生消旋化作用的机理。经PLLA热降解直接回收L-丙交酯技术的研究,可缩短PLLA再循环使用周期,既降低生产成本,又充分利用资源,达到促进发展循环经济的目的。     

Unusual change in molecular weight of polyhydroxyalkanoate (PHA) during cultivation of PHA-accumulating Escherichia coli

This study aimed to investigate the factors affecting molecular weight of poly[(R)-3-hydroxybutyrate] [P(3HB)] when polyhydroxyalkanoate (PHA) synthase (PhaRC_Bsp) from Bacillus sp. INT005 was used for P(3HB) synthesis in Escherichia coli JM109. It was found that the molecular weight of P(3HB) decreased with time in mid- and late-phase of culture and was strongly affected by culture temperature. At 37 °C culture temperature, the molecular weight of P(3HB) rapidly decreased from 4.4 × 10⁵ to 4.8 × 10⁴ with culture time, whereas it was almost unchanged at 25 °C. Kinetic analysis suggested that the decrease in molecular weight of P(3HB) was due to random scission of the polymer chain. The decrease in molecular weight of P(3HB) was not observed when PHA synthases other than PhaRC_Bsp were expressed. This study sheds light on the unique behaviour in molecular weight change of P(3HB) that is synthesized by E. coli expressing PhaRC_Bsp.     

Photodegradation of ethylene–octene copolymers with different octene contents

The influence of the octene content on the photodegradation behaviour of ethylene–octene copolymers (EOCs) was revealed by investigating the photooxidation of low density polyethylene (LDPE) and EOCs with different octene contents through a series of characterisation methods. LDPE was very sensitive to ultraviolet light and the photostabilities of EOCs decreased with increasing octene concentration. The photodegradation of all samples produced hydroxyl, carbonyl and vinyl groups. The ease of chain crosslinking and scission was increased as the octene content rose. Crosslinking predominated in late irradiation period of LDPE while chain scission was dominant in that of EOCs. Annealing and chain scission promoted the secondary crystallisation of the crystallisable chain segments. Chain scission enhanced the crystallisation ability of the irradiated EOCs while it decreased that of the weathered LDPE. The photostabilities of crystals could be ranked as follows: the chain-folded lamellar crystals > the bundled crystals > the fringed micellar crystals. The thermal stabilities and mechanical properties of samples decreased with increasing irradiation time and the decreasing extent was correlated with the comonomer content.     

Photodegradation of polyglycidol in aqueous solutions exposed to UV irradiation

The photodegradation of polyglycidol in aqueous solution with UV wavelength of 254 nm was investigated. The experiments were carried out in air at a constant temperature and the photodegradation of polyglycidol (PGl) was compared to that of poly(ethylene oxide) (PEO), the most widely studied polyether. Size exclusion chromatography with multiangle light scattering detection (SEC-MALLS) was used to measure the changes in the molar masses and molar mass dispersities of polymers during degradation. The molar mass of PGl decreased dramatically during the first period of UV irradiation and then gradually approached a limiting value of 17,000 g/mol, regardless of the initial polymer concentration. PEO was less sensitive to UV irradiation than polyglycidol however, both polymers degrade mainly via chain scission. The degradation of PGl and PEO leads to acidification of their water solution. The photooxidation products were analyzed by FTIR and NMR spectroscopy and the spectrophotometric results revealed that the irradiation of the polymers led to the formation of carbonyl groups in the macromolecular chains. A mechanism accounting for the main routes of PGl photooxidation is proposed.     

Thermal and crystallization behaviour of gamma irradiated PLLA

Structure, crystallization behaviour and some thermal properties of poly-l-lactide (PLLA), gamma irradiated up to 300 kGy, have been studied. Through differential scanning calorimetry measurements, radiation-induced changes were evident in the enthalpy of melting and cold crystallization, as well as in the degree of crystallinity. Decay of the glass transition, cold crystallization and melting temperatures with irradiation dose was observed in all cases. The annealing treatment, which can substantially reduce the concentration of free radicals, also had a great impact on thermal/crystallization behaviour of irradiated PLLA. Extensive chain scission, as a dominant effect of gamma irradiation, confirmed by gel permeation chromatography, has as a consequence a growth of new thin crystal lamellae and occurrence of the second low-temperature melting peak. Thermogravimetric analyses have shown that irradiation lowered the thermal stability of PLLA.     

Gamma polymorph and branching formation as inductors of resistance to electron beam irradiation in metallocene isotactic polypropylene

The influence of a wide dose range of electron beam (EB) irradiation is analyzed on films obtained from metallocene isotactic polypropylene (iPP) under two different thermal processing conditions. A greater irradiation resistance is observed in those films with content in γ crystallites higher than in α monoclinic entities in terms of melting temperature variation with irradiation. This change is on the order of 0.5 °C per 100 kGy in slowly crystallized films while a value of 1.5 °C per 100 kGy is found in quenched specimens. On the other hand, dual studies on films and pellets have proved that branching takes place in this metallocene iPP. The scission processes that occur during irradiation cannot account by themselves for the observed changes in molecular weight distribution as demonstrated by simulation. The observed changes in the rheological behaviour of the irradiated iPP corroborate that increasing degrees of branching are generated by the irradiation process.     

Enhanced crystallization,thermal properties,and hydrolysis resistance of poly(l-lactic acid) and its stereocomplex by incorporation of graphene nanoplatelets

Poly(d-lactic acid) (PDLA) and graphene nanoplatelets were used as nucleating agents for poly(l-lactic acid) (PLLA). The graphene (1 wt%) shows a more pronounced effect than PDLA in facilitating PLLA crystallization. Graphene effect on crystallization of stereocomplex (SC) polylactide is also demonstrated. Although medium molecular weight PLLA was blended with a limited content (1 wt%) of low molecular weight PDLA in the presence of graphene (0.5 phr), SC melting temperature is slightly increased without the use of high molecular weight polylactide pair. Also, optimal graphene content (0.5 phr–1.5 phr) promotes crystallization of PLLA homocrystals in the three-component system (PLLA/PDLA/graphene). Graphene additionally enhances Young's modulus and barrier property to thermal degradation of both PLLA and SC systems. Furthermore, PLLA/graphene is more resistant to hydrolysis than PLLA. Likewise, PLLA/PDLA/graphene is more stable than PLLA/PDLA during hydrolysis.     

Degradation behavior of poly (l-lactide-co-glycolide) films through gamma-ray irradiation

Gamma-ray irradiation is a very useful tool to improve the physicochemical properties of various biodegradable polymers without the use of a heating and crosslinking agent. The purpose of this study was to investigate the degradation behavior of poly (l-lactide-co-glycolide) (PLGA) depending on the applied gamma-ray irradiation doses. PLGA films prepared through a solvent casting method were irradiated with gamma radiation at various irradiation doses. The irradiation was performed using 60Co gamma-ray doses of 25–500 kGy at a dose rate of 10 kGy/h.The degradation of irradiated films was observed through the main chain scission. Exposure to gamma radiation dropped the average molecular weight (M_n and M_w), and weakened the mechanical strength. Thermograms of irradiated film show various changes of thermal properties in accordance with gamma-ray irradiation doses. Gamma-ray irradiation changes the morphology of the surface, and improves the wettability. In conclusion, gamma-ray irradiation will be a useful tool to control the rate of hydrolytic degradation of these PLGA films.     

Gel permeation chromatography studies of chain scission and cross-linking during photo-oxidation of atactic polystyrene below and at tg

Photo-oxidative degradation of polystyrene in the form of film 20 μm thick was carried out in air using u.v. light of 254 nm at room temperature and at temperatures up to T_g. GPC was used to study changes of molecular weight distribution during the process. The GPC results were analysed using equations for an initially most probable distribution and non-uniform energy dissipation; the quantum yield values of chain scission and cross-linking of polystyrene during degradation were calculated. Initially, degradation progressed at high rate, connected with consumption of oxygen dissolved in the film. The slower subsequent degradation was connected with consumption of oxygen supplied during the reaction. An appreciable increase in the quantum yields for chain scission and cross-linking was observed just below and at T_g for the initial stage of photo-oxidative degradation. This increase of the quantum yield of photodegradation was caused by increased mobility of oxygen molecules in the film, connected with movement of polymer chain elements.     

Degradation and stability of polyaniline on exposure to electron beam irradiation (structure-property relationship)

Polyaniline (PAni) was prepared by electrochemical polymerization and subjected to different doses of electron beam (EB) irradiation. The effect of EB irradiation causes both chain scission and cross-linking process in PAni, which depends on irradiation dose. The degree of chain scission and cross-linking in PAni by EB irradiation is characterized through XRD, TGA, DSC, solubility, EPR and electrical properties measurement. The results reveal that with increase in EB irradiation dose from 0 to 150 kGy DC and AC conductivity and dielectric constant are found to increase mainly due to the chain scission or further doping in PAni. Due to irradiation there is change in the structure of PAni, such as decrease in the d-spacing, inter-chain separation, thermal stability and T_g but increase in the percent crystallinity and solubility. With further increase in the EB irradiation dose from 150 kGy onwards the DC and AC conductivity and dielectric constant are decreased due to the cross-link formation or dedoping in PAni, which causes the decrease in percentage of crystallinity and solubility and increase in d-spacing, inter-chain separation, thermal stability and T_g of PAni.     

Hydrolysis of poly(l-lactic acid) using microwave irradiation

Poly(l-lactic acid) (PLLA) was hydrolyzed using microwave irradiation, and yields of the resultant lactic acid and reaction time were compared with those obtained by conventional heating. In both cases, the reaction temperature was maintained at 170 °C and the weight ratio of PLLA:H₂O was 3:1. Under conventional heating, the lactic acid yield reached saturation after 800 min at 45%, whereas only 120 min was required to reach the same yield level under microwave irradiation. The optical purity under conventional heating decreased with hydrolysis of the PLLA and dropped to 94%ee when the lactic acid yield reached at 45%. Under microwave irradiation, however, the optical purity decreased only after the equilibrium state of hydrolysis was attained. Therefore, to maintain the optical purity at 98%ee, it was necessary to stop microwave irradiation when the lactic acid yield reached 45%.     

Photodegradation of poly-5-bromoacenaphthylene

Bromoacenaphthylenes were synthesized and polymerized by ionic and free-radical initiation. 5-Bromoacenaphthylene was found to yield high molecular weight polymers (10⁴ < M < 10⁶). Kinetic studies on the photodegradation of poly-5-bromoacenaphthylene in solution were carried out at various temperatures in tetrahydrofuran and dioxane as solvent. The polymers were found to undergo random chain scission. The photodegradation is solvent- and temperature-dependent and leads to a lower limiting value. As for polyacenaphthylene, some weak links were detected in the polymers.     

Electron-beam treatment of poly(lactic acid) to control degradation profiles

Bioresorbable polymers such as polylactide (PLA) and polylactide-co-glycolide (PLGA) have been used successfully as biomaterials in a wide range of medical applications. However, their slow degradation rates and propensity to lose strength before mass have caused problems. A central challenge for the development of these materials is the assurance of consistent and predictable in vivo degradation. Previous work has illustrated the potential to influence polymer degradation using electron beam (e-beam) radiation. The work addressed in this paper investigates further the utilisation of e-beam radiation in order to achieve a more surface specific effect. Variation of e-beam energy was studied as a means to control the effective penetrative depth in poly-l-lactide (PLLA). PLLA samples were exposed to e-beam radiation at individual energies of 0.5 MeV, 0.75 MeV and 1.5 MeV. The near-surface region of the PLLA samples was shown to be affected by e-beam irradiation with induced changes in molecular weight, morphology, flexural strength and degradation profile. Moreover, the depth to which the physical properties of the polymer were affected is dependent on the beam energy used. Computer modelling of the transmission of each e-beam energy level used corresponded well with these findings.