A preliminary study of a colorimetric method for anisole determination

The colour reaction between anisole, concentrated sulphuric acid and formaldehyde has been studied in glacial acetic acid as solvent The reaction can be used for the quantitative colorimetric analysis of anisole in mixtures with acetic acid and with benzene.     

Measurement of volatile organic compounds emitted in libraries and archives: an inferential indicator of paper decay?

Background

A sampling campaign of indoor air was conducted to assess the typical concentration of indoor air pollutants in 8 National Libraries and Archives across the U.K. and Ireland. At each site, two locations were chosen that contained various objects in the collection (paper, parchment, microfilm, photographic material etc.) and one location was chosen to act as a sampling reference location (placed in a corridor or entrance hallway).

Results

Of the locations surveyed, no measurable levels of sulfur dioxide were detected and low formaldehyde vapour (< 18???g?m^-3) was measured throughout. Acetic and formic acids were measured in all locations with, for the most part, higher acetic acid levels in areas with objects compared to reference locations. A large variety of volatile organic compounds (VOCs) was measured in all locations, in variable concentrations, however furfural was the only VOC to be identified consistently at higher concentration in locations with paper-based collections, compared to those locations without objects. To cross-reference the sampling data with VOCs emitted directly from books, further studies were conducted to assess emissions from paper using solid phase microextraction (SPME) fibres and a newly developed method of analysis; collection of VOCs onto a polydimethylsiloxane (PDMS) elastomer strip.

Conclusions

In this study acetic acid and furfural levels were consistently higher in concentration when measured in locations which contained paper-based items. It is therefore suggested that both acetic acid and furfural (possibly also trimethylbenzenes, ethyltoluene, decane and camphor) may be present in the indoor atmosphere as a result of cellulose degradation and together may act as an inferential non-invasive marker for the deterioration of paper. Direct VOC sampling was successfully achieved using SPME fibres and analytes found in the indoor air were also identified as emissive by-products from paper. Finally a new non-invasive, method of VOC collection using PDMS strips was shown to be an effective, economical and efficient way of examining VOC emissions directly from the pages of a book and confirmed that toluene, furfural, benzaldehyde, ethylhexanol, nonanal and decanal were the most concentrated VOCs emitted directly from paper measured in this study.     

Sensitive reaction rate method for the determination of low levels of formaldehyde with photometric detection

A simple and rapid method is proposed for the determination of ultra trace amounts of formaldehyde. It is based on the catalytic effect of formaldehyde on the oxidation of Brilliant cresyl blue by bromate. The reaction is monitored photometrically by measuring the decrease in absorbance of the dye. Formaldehyde in the range of 0.005–2.300 μg/mL can be determined with a limit of detection of 0.003 μg/mL. The relative standard deviation for ten replicate measurements of 1.5 μg/mL formaldehyde is 0.1%. The method was used for the determination of formaldehyde in real samples with satisfactory results. Received: 26 May 1998 / Revised: 30 September 1998 / Accepted: 3 October 1998     

Kinetics of the formation of copper β-octaphenylporphyrin complexes in pyridine and acetic acid

The formation kinetics of copper β-octaphenylporphyrin complexes in pyridine and acetic acid is reported and is compared with that of copper β-octamethylporphyrin and dodecaphenylporphyrin complexes. The introduction of electron-donating or electron-withdrawing substituents in the β-positions of the porphyrin macrocycle change the rate of the complexation reaction by at most one order of magnitude. On passing from the planar porphyrin macrocycle to the heavily distorted one, the rate of the reaction in pyridine (electron donor solvent) and acetic acid (electron acceptor solvent) increases and decreases, respectively, by several orders of magnitude.     

Spectrophotometric determination of formaldehyde in air

A spectrophotometric method for the determination of formaldehyde in air is described, based on the colour reaction of formaldehyde, p-aminoazobenzene and sulphur dioxide in hydrochloric acid medium. Beer's law is obeyed at 505 nm in the range 2-12 mug of formaldehyde per 25ml of final solution (0.08-0.48 ppm). Optimum conditions for colour development, and possible interferences, have been studied.     

Fluorometric determination of formaldehyde

A simple, selective and sensitive fluorometric method is presented for the determination of formaldehyde in water based on its reaction with 3,4-diaminoanisole in alkaline ethanol-water solution to give a strongly fluorescing Schiff base. The dependence of the fluorescence intensity on the solvent composition, quenching by acetic and sulphuric acid, heating time and interference by other compounds is discussed. The detection limit of the method is 0.6 μg/L. The recovery of formaldehyde spiked into river water is 93% with an R.S.D of 6.05% at a concentration level of 10 μg/L. Received: 18 November 1996 / Revised: 17 February 1997 / Accepted: 18 February 1997     

TiO2/柚子皮生物质活性炭复合材料的制备和吸附光降解性研究

本文以自制柚子皮生物质活性炭为原料,采用凝胶-溶胶法合成TiO2/柚子皮生物质活性炭复合材料(TiO2/BAC)。对复合材料进行SEM、FTIR、XRD等表征,并研究该复合材料对中性红、亚甲基蓝染料及甲醛的吸附降解性能。结果表明,在复合材料中柚子皮生物质活性炭的添加量为7 g、预吸附时间为2 h时,对染料具有最佳的吸附降解效果,复合材料在循环使用5次后对染料的吸附降解率仍达到了80 %以上。当活性炭的添加量为6 g、复合材料的添加量为2 g时,复合材料对甲醛的吸附降解达到最大,可达61%。表明该复合材料对中性红、亚甲基蓝染料及甲醛具有良好的吸附降解效果,有望用于废水染料的去除和家居甲醛净化。     

Non-destructive dating of fiber-based gelatin silver prints using near-infrared spectroscopy and multivariate analysis

An innovative approach to date fiber-based gelatin silver prints using near-infrared spectroscopy (NIR) and multivariate analysis is presented. NIR spectra were acquired for 152 film stills printed in the USA between 1914 and 1986, and partial least square (PLS) analysis was used to correlate the spectra with the year the photographs were printed. Principal component analysis and spectral interpretation helped clarify the underlying correlation between the print date and the composition and ageing of the photographic papers. The method was successfully validated with an independent set of 66 film stills printed in the USA, and a prediction error (root mean square error of prediction) of 6 years was achieved. The method was also tested on films stills printed in Germany and Russia, as well as amateur prints and photographs in the collection of the Museum of Modern Art. The prediction error was significantly larger, with the exception of the amateur prints, due to differences in the composition and/or properties of the papers depending on their geographical origin and purpose as confirmed by discriminant analysis.     

Ag/MgO串联协同催化降解偶氮染料

以纳米氧化镁为载体,采用浸渍法制备一系列过渡金属负载型催化剂.测试其对染料的降解性能后筛选出了效果最优的催化剂Ag/MgO,并采用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、扩展X射线吸收精细结构谱(EXAFS)以及X射线吸收近边结构(XANES)等表征方法对该催化材料的结构特征、微观形...     

Dyeing wool and cotton fibres with acidic extract of Hibiscus rosa sinensis flower

Abstract

The focus of this work is to extract a natural dye for colouring camel wool as a substitute for synthetic dyes used in the Sadu House of Kuwait. Their target is to keep the tradition of tent and rug production natural in all its manifestations. Therefore, our task was to find an abundant source that provides a colour preferably red to purple. Hibiscus rosa sinensis (HRS) is an abundantly available plant in Kuwait that was explored for extraction of the red dye to colour camel wool permanently. The powdered petals of red flowers of HRS was extracted with 5% acetic acid which yielded a deep red colour that showed a great potential for woollen fibre dyeing. The use of mordants like alum and some metal salts manifested a wide range of fixed colours which intensified at 85 °C. The colours produced had excellent fastness and was accepted by the Sadu House.     

Stereochemie und Mechanismus derPrins-Reaktion bei ausgeprägter Ladungsdelokalisierung im intermediären Carbeniumion

A detailed investigation of the reaction of 2.6-dimethyl-4-propenylphenol with formaldehyde showed thatPrins reactions of hydroxystyrenes in alkaline medium in most cases are kinetically controlled. By attack of formaldehyde, the same intermediate is generated from eithercis ortrans olefin. On further reaction by two independent pathways a 1.3-diol is formed by attack of a hydroxyl ion, or a 1.3-dioxane by reaction with additional formaldehyde via a hemiacetal. The steric course of the reaction is deduced from a discussion of the conformations of transition states.Prins reactions of arylolefins carrying strong +M-substituents proceed analogously under acylating conditions (e.g. in acetic acid) in weak acidic medium.

---

---

Mit 2 Abbildungen     

对氨基偶氮苯及其盐酸盐的分光光度法测定

对氨基偶氮苯(简称p-AAB)及其盐酸盐(简称p-AAB·HCl),是一有机中间体,又是有机试剂。有关它的含量测定,目前生产上缺少一适当的方法。p-AAB是芳伯胺,若用重氮化或非水酸碱滴定。     

A comparative study of the behaviour of Crystal Violet,alizarin-9-imine and quinalizarin-9-imine as indicators in anhydrous acetic acid medium

A comparative study has been made of the behaviour of alzarin-9-imine, quinalizarin-9-imine and the widely used Crystal Violet as indicators in anhydrous acetic acid medium. The protonation constants of quinalizarin-9-imine, and the properties required by a base if it is to be titratable in acetic acid medium with use of the indicators studied, the chromaticity co-ordinates, optimal concentration for titration and the quality of the colour changes have been determined. The results obtained show Crystal Violet and alizarin-9-imine to be very good indicators in acetic acid medium but alizarin-9-imine gives better end-point location. Quinalizarin-9-imine is also a good indicator but exhibits poorer colour change quality than the other two.     

Modified Natural Rubber as a Simple Chemical Sensor with Smartphone Detection for Formaldehyde Content in a Seafood Sample

A new biodegradable platform-based sensor for formaldehyde assay is proposed. Natural rubber latex was modified to polylactic acid–chloroacetated natural rubber polymer blend sheets. The polymer blend sheet was grafted using a water-based system with amine monomers as a platform, with a spot exhibiting positive polarity for immobilizing with anionic dye (Acid Red 27). The sensor was exposed to formaldehyde. The color intensity of the dye on the sensor spot would decrease. Using a smartphone with image processing (via ImageJ program), the color intensity change (∆B) could be followed. A linear calibration, ∆B intensity = 0.365 [FA] + 6.988, R² = 0.997, was obtained for 10–150 mM FA with LOD and LOQ at 3 and 10 mM, respectively (linear regression method). The precision was lower than 20% RSD. Application to real seafood samples was demonstrated. The ready-to-use sensor with the proposed method was cost-effective, was portable for on-site analysis, and demonstrated green chemical analysis.     

The inhibition of Saccharomyces cerevisiae cells by acetic acid quantified by electrochemistry and fluorescence

In this paper, the effect of acetic acid on S. cerevisiae metabolism was studied for the first time with the combinational utilization of the mediated electrochemical method and intrinsic fluorescence method, and the results from both methods were compared with each other. It was confirmed in vivo that not only the glycolysis enzymes but also the NADH dehydrogenase were sensitive to acetic acid. The established technique might also be applicable in studying the toxicity of other environmental pollutants, such as phenol and its derivatives.     

Determination of ultramicro amounts of sulphate as methylene blue—II The reduction

Sulphate may be determined spectrophotometrically as methylene blue after reduction to sulphide, which is allowed to react with p-aminodimethylaniline and ferric iron to form the dye. A previous paper¹ dealt with the colour reaction; this paper deals with the reduction.

A method for the reduction of sulphate to sulphide by hydriodic and hypophosphorous acids in acetic acid solution is proposed. It is founded on an investigation of the following variables: composition of the reducing reagent, composition of the carrier gas and gas-washing liquid, temperature at reduction, and time. The yield of the reduction is found to be 100% within the experimental errors. The standard deviation of a single determination of 100 μg S or 2 μg S is found to be 0.14 μg S or 0.05 μg S, respectively. Some interferences in connection with the application of the method for certain purposes are discussed.     

Effects of NO2 and acetic acid on the stability of historic paper

This research investigates degradation of historic paper in polluted environments during long-term dark storage. In an innovative experiment, degradation rates at realistic pollution levels are compared with degradation rates in the absence of pollution, using a set of real historic papers. The most abundant pollutants in repositories in post-industrial environments are taken into account: acetic acid and nitrogen dioxide. Their action was assessed in terms of reduction of ‘handling’ (as defined by decrease in degree of polymerisation) and ‘display’ (as defined by discolouration) lifetimes. Extrapolations to room conditions enabled lifetime predictions in conditions that are comparable to a real archival or library repository environments while prediction uncertainties were analytically evaluated to assess the significance of conclusions. While 10 ppb of NO₂ does reduce the handling lifetime of almost all types of paper, their predicted lifetimes were still assessed to be several millennia, with the exception of acidic paper. Acetic acid at concentrations that are typical for archival and library repositories (<100 ppb) has significantly less effect than NO₂ while it does not affect display lifetimes. From a conservation management perspective, it needs to be addressed whether the predicted reductions in otherwise significant handling lifetimes are of real concern and whether air filtration in archival and library repositories is justified.     

Oxidation of Polyisoprene Popcorn Polymer. III. Further Studies on Water and Carbon Dioxide Production

The volatile products resulting from polyisoprene popcorn polymer oxidation were analyzed quantitatively for carbon dioxide and water, and semiquantitatively for formaldehyde. The production of these three products was a linear function of the amount of oxygen consumed in the reaction. For every mole of oxygen reacted, 0.098 mole of water, 0.038 mole of carbon dioxide, and > 0.016 mole of formaldehyde were formed. Twenty-four products were detected after extensive oxidation; the major ones being water, carbon dioxide, formaldehyde, formic acid, 2,5-hexanedione, and acetic acid. No levulin-aldehyde was identified in the products. A tentative oxidation mechanism is discussed.     

A sensitive flow-injection method for determination of trace amounts of nitrite

A new sensitive colour reaction for nitrite determination is presented. In acidic medium, nitrite was reacted with safranine to form a diazonium salt which caused the reddish-orange dye colour of the solution to change to blue. The carrier stream, into which the sample solution was injected, was doubly distilled water. The reagent solution stream, which contained safranine dye, hydrochloric acid and potassium chloride, was mixed with the carrier in a 3-m length of silicon tubing (bore 0.5 mm) maintained at 30°C in a thermostatic bath. The absorbance intensity was measured at 520 nm. The detection limit was 20 ng ml⁻¹ and the RSD% of 20 injections of 1 μg ml⁻¹ of nitrite was 0.65%. Analysis can be done at a rate of up to 30 h⁻¹. Under the optimum conditions in the concentration range of 30–4000 ng ml⁻¹ of nitrite ion, a linear calibration graph was obtained (r=0.9999). The method was applied successfully to the determination of nitrite in sausages.     

Plasmonic-based colorimetric and spectroscopic discrimination of acetic and butyric acids produced by different types of Escherichia coli through the different assembly structures formation of gold nanoparticles

We present a plasmonic-based strategy for the colourimetric and spectroscopic differentiation of various organic acids produced by bacteria. The strategy is based on our discovery that particular concentrations of dl-lactic, acetic, and butyric acids induce different assembly structures, colours, and optical spectra of gold nanoparticles. We selected wild-type (K-12 W3110) and genetically-engineered (JHL61) Escherichia coli (E. coli) that are known to primarily produce acetic and butyric acid, respectively. Different assembly structures and optical properties of gold nanoparticles were observed when different organic acids, obtained after the removal of acid-producing bacteria, were mixed with gold nanoparticles. Moreover, at moderate cell concentrations of K-12 W3110 E. coli, which produce sufficient amounts of acetic acid to induce the assembly of gold nanoparticles, a direct estimate of the number of bacteria was possible based on time-course colour change observations of gold nanoparticle aqueous suspensions. The plasmonic-based colourimetric and spectroscopic methods described here may enable onsite testing for the identification of organic acids produced by bacteria and the estimation of bacterial numbers, which have applications in health and environmental sciences.