Plutonium extraction from mixed aqueous media. Plutonium—Uranium separation

A systematic study is presented on Pu IV extraction with tri-n-butyl phosphate and trilaurylamine from binary mixtures of H₂SO₄ with HCl and HBr. The addition of sulfuric acid to the mentioned mineral acid solutions, was found to affect appreciably D_Pu, which recommended some useful purification procedures. The effect of water-miscible alcohols on the extraction of plutonium from HCl and HNO₃ solutions was also investigated.     

Extraction of some elements of the groups IV b and VI b with 1-phenyl-3-methyl-4-caproyl-pyrazolone-5 (PMCP) from aqueous mineral acid solutions

Solvent extraction of Cr(VI), Mo(VI), W(VI) and Hf(IV) with 1-phenyl-3-methyl-4-caproyl-pyrazolone-5 (PMCP) in methyl isobutylketone (MIBK), xylene and chloroform (CHCl₃) from mineral acid solutions was studied. Chromium(VI) is not extracted from any of the acids studied (HCl, H₂SO₄ and HClO₄). Molybdenum(VI) is quantitatively extracted by the reagent in xylene and CHCl₃ from HClO₄ and HNO₃ solutions. It is also extracted quantitatively by the reagent in MIBK from HCl, HNO₃ and H₂SO₄ solutions but the participation of the diluent as extractant is considerable. Tungsten(VI) is quantitatively extracted in xylene from 9M HClO₄ solution. MIBK used as diluent also affects its extraction with PMCP. Hafnium(IV) is not extracted from H₂SO₄ solutions while it extracts more than 99% at 3M HNO₃ and above. The extracted species likely are: MoO₂(PMCP)₂, WO₂(PMCP)₂ and Hf(PMCP)₄, respectively.     

Speciation in strongly acidic metastable solutions of oxotungstate(vi) compounds

The ionic composition of long-lived metastable aqueous solutions of oxo compounds of tungsten(IV) with pH ≤ 1 was studied by spectrophotometry. The nature of some isopolytung-states formed in these solutions in the presence of various inorganic acids (HCl, HClO₄, HNO₃, H₂SO₄, and H₂SeO₄) was established.     

LIX 84 as an extractant for throium(IV), uranium(VI) and molybdenum(VI)

The extraction order of Th(IV), U(VI) and Mo(VI) based on pH_0.5 values is Mo(VI)>U(VI)>Th(IV). Quantitative extraction has been observed for U(VI) by mixture of 10% (v/v) LIX 84 and 0.1M dibenzoylmethane at pH 4.2 and by mixture of 10% LIX 84 and 0.05M HTTA in the pH range 5.5–7.3 and for Mo(VI) by 10% LIX 84 from chloride media at pH 1.5. The order of extraction of Mo(VI) from 1N acid solutions is HCl>H₂SO₄>HNO₃>HClO₄ and extraction decreases very rapidly with increase in the concentration of HCl as compared to that from H₂SO₄, HNO₃ and HClO₄ acid solutions. The diluents C₆H₆, CCl₄ and CHCl₂ are found to be superior ton-butyl alcohol and isoamyl alcohol for extraction of Mo(VI). Influence of concentration of different anions on the extraction of U(VI) and Mo(VI) has been studied. Very little extraction has been observed in case of Th(IV) by LIX 84 or its mixtures with other chelating extractants or neutral donors.     

Extraction of molybdenum(VI) by 4-(5-nonyl)pyridine in benzene from aqueous mineral acid solutions containing thiocyanate ions

Extraction of Mo(VI) by 4-(5-nonyl)pyridine (NPy) in benzene from mineral acid solutions containing thiocyanate ions has been investigated at room temperature (23±2°C). From mineral acid (HCl, HNO₃, and H₂SO₄) solutions alone Mo(VI) is not extracted quantitatively while the presence of small amounts of KSCN in the system augments the extraction by a large factor. Stoichiometric studies indicate that ion-pair type complexes (NPyH)₂·[MoO₂(SCN)₄] are responsible for the extraction. Separation factors determined at fixed extraction conditions (0.1M Npy/C₆H₆–0.1M acid +0.2M KSCN) reveal that Ag(I), Cu(II), Co(II), Zn(II), Hg(II) and U(VI) are co-extracted while a clean separation from alkali metals, alkaline earths and some transition metals like Ln(III), Zr(IV), Hf(IV), Cr(III), Cr(VI) and Ir(III) is possible. Some of the complexing anions like oxalate, citrate, acetate, thiosulfate or ascorbate do not affect the degree of extraction of Mo(VI) allowing it to be recovered from diverse matrices.     

Liquid-liquid extraction of molybdenum(VI) and uranium(VI) by LIX 622

The order of extraction of Mo(VI) from 1M acid solutions by 5% (v/v) LIX 622 (HL) in benzene is HCl>HNO₃>HClO₄>H₂SO₄, and extraction decreases with increasing concentration of HCl and H₂SO₄, and increases slightly with increasing concentration of HNO₃ and HClO₄. The extracted species is shown to be MoO₂L₂ as established by IR data of organic extracts and the extracted species in the solid form. Extraction is almost quantitative at and above 10% LIX 622, and is found to be independent of [Mo(VI)] in the range of 10^–4 to 10^–3 M. The diluents CCl₄, CHCl₃ and C₆H₆ are found to be superior to solvents of high dielectric constant for extraction of Mo(VI). Extraction of uranium(VI) by 10% (v/v) LIX 622 in benzene was found to increase with increasing equilibrium pH (3.0 to 6.0), and becomes quantitative at pH 5.9. Tributyl phosphate acts as a modifier up to 2% (v/v). Thorium(IV) is almost not extracted by LIX 622 or its mixture. Separation of Mo(VI) and U(VI) is feasible.     

Solvent extraction of hafnium(IV)

^{175, 181}Hafnium(IV) was extracted by HDBP in 2-ethylhexanol from 1–10M solutions of HClO₄, HCl and HNO₃, and 1–8M H₂SO₄. As with low polar organic phase diluents, the acidity dependence of the distribution ratio of Hf, D, passes through a minimum for HClO₄, HCl, and H₂SO₄ whereas only an increase of D can be observed with increasing HNO₃ concentration. From the slope analysis the following complexes were found to be extracted (HDBP=HA): HfA₄ at <4M HClO₄ and <5M HCl, lg K_extr=9, HfX₄(HA)₄ (X=ClO ₄ ⁻ , Cl⁻ or NO ₃ ⁻ ) at >5M HClO₄, >7M HCl and 1–10M HNO₃, Hf(SO₄)A₂(HA)_3–4 at <3M H₂SO₄, and Hf(SO₄)₂ (HA)₄ at >6M H₂SO₄. Coextraction of sulphate with hafnium from H₂SO₄ solutions was evidenced in experiments with macro concentrations of Hf(IV) and³⁵SO ₄ ²⁻ . Part XX: Coll. Czech. Chem. Commun., 40 (1975) 3617.     

Extraction with benzene and its derivatives

The extractability of selenium halides with benzene and some of its derivatives has been investigated using a radioactive tracer technique in order to establish the optimum conditions for its extraction. It has been found that Se(IV) is poorly extracted from HCl, HBr or H₂SO₄ solutions but high distribution ratios are observed with binary mixtures of 9M H₂SO₄ and acid halides. The extraction of some other elements is also studied under the conditions selected for Se(IV) extraction and it has been found that only antimony follows Se(IV) in the organic phase. In view of the data obtained, analytical advantages are mentioned and separation procedures are recommended. The extraction mechanism is also discussed and the role of sulfuric acid in the extraction system is explained.     

Liquid-liquid extraction of 233Pa(V) with Aliquat 336</p> </p>

Summary The extraction of protactinium with Aliquat 336 (methyl-tri-caprylyl ammonium chloride) in toluene, cyclohexane and chloroform from HCl, HNO₃, H₂SO₄, HClO₄, HF and mixed HCl-HF media was investigated by radioactive tracer technique. Distribution ratios of protactinium between the aqueous solution and the organic phase were determined as a function of shaking time, concentrations of acid in aqueous solution phase, extractant concentration and type of diluents in the organic phase. Aliquat 336 can almost quantitatively extract protactinium from strong HCl solution. At the same time, small amounts of HF in HCl solutions have a strong effect on Pa distribution.</p> </p>     

Solvent extraction studies on tetravalent selenium

A systematic study has been carried out on the extraction of SeI₄, by various water-immiscible organic solvents. Extraction has been investigated as a function of H₂SO₄ and Kl concentrations. It has been found that Se(IV) extraction is appreciably increased by addition of iodide ion to sulfuric acid solutions. On the other hand, the presence of water-miscible alcohols and acetone was found to enhance Se(IV) extraction from H₂SO₄–Kl solutions. In the light of the results, an extraction mechanism is suggested.     

Determination of inorganic acids by ion chromatography with n-tetradecylphosphocholine (zwitterionic surfactant) as the stationary phase and pure water as the mobile phase

A new ion chromatographic (IC) system, in which n-tetradecylphosphocholine (TDPC, a phosphobetaine type of zwitterionic surfactant) was used as the stationary phase, pure water as the mobile phase, and conductivity as the method of detection, has been developed for the determination of inorganic acids. Five model acids, HCl, HNO₃, HClO₄, H₂SO₄, and H₃PO₄, were separated to baseline and eluted in the order H₃PO₄ > HCl > HNO₃ > H₂SO₄ > HClO₄. When peak areas were plotted against the concentrations of the acids in samples, linear calibration curves were obtained. Ultimate determination limits were approximately 1 mmol L^–1, but the discrimination of the method between solutions of different concentration was better than 10 μmol L^–1 for those model analytes. Salts of divalent cations could also be separated, but they were eluted faster than the acids. No separation was observed for the salts of monovalent cations. This newly proposed approach is applicable to the simultaneous determination of the inorganic acids (produced by reactions of NO_x, SO_x, and HCl with water) in aerosols.     

Liquid-liquid extraction and recovery of indium using Cyanex 923

The extraction of In(III) from HCl, H₂SO₄, and HNO₃ media using a 0.20 mol l⁻¹ Cyanex 923 solution in toluene is investigated. In(III) is quantitatively extracted over a fairly wide range of HCl molarity while from H₂SO₄ and HNO₃ media the extraction is quantitative at low acid concentration. The extracted metal ion has been recovered by stripping with 1.0 mol l⁻¹ H₂SO₄. The stoichiometry of the In(III): Cyanex 923 complex is observed to be 1:2. The extraction of In(III) is insignificantly changed in diluents namely toluene, n-hexane, kerosene (160-200 °C), cyclohexane, and xylene having more or less the same dielectric constants, whereas, it decreases with increasing polarity of diluents such as cyclohexanone and chloroform. The extractant is stable towards prolonged acid contact and there is a negligible loss in its extraction efficiency even after recycling for 20 times. The extraction behavior of some commonly associated metal ions namely V(IV), Ti(IV), Al(III), Cr(III), Fe(III), Ga(III), Sb(III), Tl(III), Mn(II), Fe(II), Cu(II), Zn(II), Cd(II), Pb(II), and Tl(I) has also been investigated. Based on the partition data the conditions have been identified for attaining some binary separations of In(III). These conditions are extended for the recovery of pure indium from zinc blend, zinc plating mud, and galena. The recovery of the metal ions is around 95% with purity approximately 99%.     

Flocculation of Butadiene-Styrene Latex with Polymeric Ammonium Salts of N,N-Dimethylaminoethyl Methacrylate and Mineral Acids

The flocculation performance of cationic polyelectrolytes (polymeric ammonium salts of N,N-dimethylaminoethyl methacrylate) and mineral acids (HCl, HNO₃, H₂SO₄, H₃PO₄) in recovery of rubber from SKS-30 ARK butadiene-styrene latex was studied.     

Electrical conductivity of aqueous acids in binary and ternary water-electrolyte systems

We analyze electrical conductivity data for aqueous solutions of strong and weak acids over a wide range of concentrations at various temperatures. Electrical conductivity isotherms in these solutions are characterized by peaks, whose parameters correlate with the molecular structure of solutions. On the basis of the concentration dependence of the activation energy of electrical conductivity, the acid solutions are divided into two groups. One includes HIO₃, H₂SO₄, and H₃PO₄; the other includes HCl, HBr, HI, HClO₄, HNO₃, and carboxylic acids. We show that anomalous proton migration is operative only in low-concentration solutions until their concentration reaches the peak on conductivity isotherms. The effect of extrinsic ions on proton mobility and on conductivity in acid-salt-water systems is considered.     

Mechanical degradation of filter polymer materials: Polyphenylene sulfide

Polyphenylene sulfide (PPS) is known as a material resistant to high temperature and chemicals; however, there are arguments on the durability of PPS non-woven fabrics to chemicals, such as nitric acid (HNO₃), sulfuric acid (H₂SO₄), and hydrochloric acid (HCl). Therefore, this work aims at investigating the degradation of PPS non-woven fabrics in HNO₃, H₂SO₄ and HCl, and at confirming acid durability of PPS non-woven fabrics. In addition, this paper also studies the interaction among these three acids by measuring the retention of strength in binary or tertiary mixtures of these three acids. A discussion has been made on the acceleration/retardation of PPS degradation by the interactive effects, and also on the chemistry related to the degradation by these acids. Furthermore, there is a linear relationship between the nitric acid concentration and the proportion of carbon in the remaining PPS structures after 100 h of acid exposure. Also, this proportion of carbon is a good indicator of the retained strength in PPS fabrics.     

Size-controlled synthesis and formation mechanism of manganese oxide OMS-2 nanowires under reflux conditions with KMnO4 and inorganic acids

This study presents a simplified approach for size-controlled synthesis of manganese oxide octahedral molecular sieve (OMS-2) nanowires using potassium permanganate (KMnO₄) and different inorganic acids (HCl, HNO₃, and H₂SO₄) under reflux conditions. The morphology and nanostructure of the synthesized products are characterized by X-ray diffraction, Ar adsorption, and electron microscopy analysis, in order to elucidate the controlling effects of acid concentration and type as well as the formation mechanism of OMS-2 nanowires. The concentration of inorganic acid is a crucial factor controlling the phase of the synthesized products. OMS-2 nanowires are obtained with HCl at the concentration ≥0.96 mol/L or with HNO₃ and H₂SO₄ at the concentrations ≥0.72 mol/L. Differently, the type of inorganic acid effectively determines the particle size of OMS-2 nanowires. When the acid is changed from HCl to HNO₃ and H₂SO₄ in the reflux system, the average length of OMS-2 declines significantly by 60–70% (1104–442 and 339 nm), with minor decreased in the average width (43–39 and 34 nm). The formation of OMS-2 nanowires under reflux conditions with KMnO₄ and inorganic acids involves a two-step process, i.e., the initial formation of layered manganese oxides, and subsequent transformation to OMS-2 via a dissolution-recrystallization process under acidic conditions. The proposed reflux route provides an alternative approach for synthesizing OMS-2 nanowires as well as other porous nano-crystalline OMS materials.     

Extraction studies of Pu(IV) with octylphenyl acid phosphate

Octylphenyl acid phosphate, the commercially available mixture of monooctylphenylphosphoric acid (MOPPA) and dioctylphenylphosphoric acid (DOPPA) in xylene medium has been employed as an extractant for distribution studies on Pu(IV) in different mineral acids including phosphoric acid. It was found possible to extract Pu quantitatively from an acid mixture comprising 2.5M H₃PO₄, 0.75M H₂SO₄ and 0.5M HNO₃. Quantitative stripping was observed with a mixture of 0.25M oxalic acid and 0.2M ammonium oxalate.Parts of this work have been reported at symposie (Refs^1,2)     

Solvent extraction of hafnium(IV) by TBP and topo from acidic organic-aqueous solutions

Tracer concentrations of Hf(IV) were extracted by 60% TBP solution in benzene from 5M HClO₄, 5M HCl, 6M HNO₃ and 8M H₂SO₄ solutions, and by 1·10^?4 M TOPO solution in benzene from 2M HClO₄ and 2M HCl solutions in the presence of a variety of organic solvents miscible with the aqueous phase. Whereas for TBP these solvents caused an increase of HF(IV) extraction, an opposite effect was observed for TOPO. The results were discussed from the point of view of various solute-solvent and solvent-solvent interactions.     

Studies on extraction of zirconium(IV) by tricapryl methyl ammonium chloride from sulphate media and its separation from hafnium(IV)

The distribution of Zr(IV) between aqueous H₂SO₄ solutions and organic phases of tricapryl methyl ammonium chloride has been described. The dependence of extraction on acidity, metal and solvent concentration, diluent type and temperature was thoroughly investigated. The possible extraction mechanism is discussed in the light of results obtained. A method for the separation of Hf(IV) from Zr(IV) is also suggested.     

Extraction of europium from mixed acids and mixed aqueous—Organic media

The extraction of Eu with Amberlite LA-2, TBP and HDEHP from HF, HCl, HBr, H₂SO₄, CH₃ COOH and KI solutions was investigated. The extraction of Eu with TBP and LA-2 is small over a wide range of concentrations. The extraction of Eu with HDEHP from HCl, HBr, and H₂SO₄ is inversely proportional to the third power of the acid concentration, while the extraction from KI is proportional to the square of the extractant concentration. The extraction by the three extractants from H₂SO₄ in presence of small amounts of hydrogen halides is small. These extraction data can be used to separate Eu from Th and many of the fission products. The presence of water-miscible alcohols and acetone generally increases the extraction of Eu from H₂SO₄ and KI solutions.